CNB V3810PF User Manual
USER INFORMATION:
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION!
Explanation of two Symbols
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM
OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT
TO RAIN OR MOISTURE"
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.
PRECAUTION:
!
All the warnings and instructions of this manual should be followed.
Remove the plug from the outlet before cleaning. Do not use liquid
aerosol detergents. Use water damped cloth for cleaning.
To reduce the risk of fire or electric shock, do not expose this appliance
to rain or moisture.
Do not place anything on top of the unit that might spill or fall into it.
Do not attempt to service this unit yourself as opening or removing
covers may you to dangerous voltage or other hazards. Please refer
all servicing to qualified service personnel.
Keep enough space around the unit for ventilation.
Slots and openings on the monitor should not be blocked.
During flashes of lightning or cracks of thunder, or when the system
is not used for a long time, unplug the system power supply to
protect the unit from lightening or power surges.
Dome (Ø68), (Ø85)
SPECIFICATIONS:
Signal System
Scanning System
Scanning Frequency (H)
Scanning Frequency (V)
Image Sensor
Total/Effective Pixels No.
S/N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC
Input/Output Connector
Power Consumption
(Option: AC 24V/DC 12V)
Dome Size (Ø
※
AC 24V / DC 12V: Ø85 Only
410K/380K [Normal:270K/250K] 470K/440K[Normal:320K/290K]
)
Design and specifications
are subject to change
without notice.
P/N:3810-0084A
NTSC : 525 Lines PAL : 625 Lines
15.734kHz 15.625kHz
550 TV Lines / 480 TV Lines / 380 TV Lines
Fixed Lens (f=3.8mm, 6.0mm Selectable)
1/60~10,000 Sec. 1/50~10,000 Sec.
Power(Red or Green Jack), Video(Yellow Jack)
AC 24V (20V~28V) or DC 12V (10V~15V), 5W (Max)
2 : 1 Interlace
59.94Hz 50Hz
1/3 inch SONY Super HAD CCD
More than 48dB
1.0 Vp-p (75 Ohms, composite)
Manual
Internal
0.3 Lux(High) / 0.1 Lux(Normal)
Auto
Auto
DC 12V (DC 9V~15V) / 3W (Max)
68mm / 85mm
ver.0611E
Digital
CCD CameraColor Dome
Color DomeDigital DSP
cameracolor
LENS
1/3" SONY CCD
.Fixed Lens
COMPOSITION:
Vandal Resistant Dome Camera
Ø
68
Ø
68
Ø
85
Owner's Manual
Vandal Resistant Dome Camera
Owner's Manual
Vandal Resistant Dome Camera
Owner's Manual
L-Wrench
L-Wrench
L-Wrench
(Surface Type)
Mounting Screw
(Flush Type)
Mounting Screw
(Surface Type)
Mounting Screw
Guide Pattern
Guide Pattern
Guide Pattern
CONNECTION:
DC 12V Power Type
#
1
Video
(Yellow)
Power - DC 12V
(Red)
#
2
AC 24V/DC 12V Power Type
#
1
Video
(Yellow)
Power - AC 24V/ DC 12V
(Green)
#
2
Video Output
GND
Video Output
GND
※
AC 24V / DC 12V: Ø85 Only
You must be fully aware of all the
distinctive features and precautions
related to this camera before installing it.
• The wire is polarized.
• Use DC 12V power source.
No.
#1
#2
Function
Video Output
Power Input
Terminal Color
Yellow
Red
Remark
1.0 Vp-p
DC12V(10V~15V),
3W(Max)
• The wire is non-polarized.
• Use AC 24V power source or
DC 12V power source.
No.
#1
#2
Function
Video Output
Power Input
Terminal Color
Yellow
Green
Remark
1.0 Vp-p
AC24V(20V~28V) or
DC12V(10V~15V),5W(Max)
TROUBLESHOOTING:
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem,
contact an authorized technician.
The image does
not appear on the
screen.
The image on the
screen is dim.
The camera does
not work properly,
the surface of the
camera case is hot,
and a black line
appears on the
screen.
The screen blinks
a lot.
Check the power source for the monitor
and camera and assure that the voltage
and polarity are properly connected and
being supplied correctly.
Check if the lens is stained. If dirty,
clean the lens with a soft, clean cloth.
Adjust the Back Focus of the lens again.
Check if you have connected the camera
to a proper power source and If there is
no problem with the power, turn the unit
off immediately and seek assistance from
our After Service department.
Check if the camera is pointed toward
the sun or a fluorescent lamp.
Adjust the angle or location of the
camera if too much light is coming into
the screen.
Loading...