CNB V2862PVF User Manual

COMPOSITION:

Surface Mount Bracket

Owner's Manual

You must be fully aware of all the distinctive
features and precautions related to this
camera before installing it.

Service Monitor Cable

Tapping Screw

L-Wrench

Surface Mount Screw

Guide Pattern

Simple to install

3-Axis bracket makes
adjustment easy.

The 3D bracket (Pan, Tilt and Horizontal)
allows the camera to be manually as well
as moved horizontally and vertically.

s

e

n

i

L

V

T

SDNR

SDNR

0

5

5

•

Super

Super

Digital

Digital

Noise

Noise

R

eduction

R

eduction

s

t

a

n

i

l

l

o

•

S

u

p

e

r

D

i

g

i

t

a

l

N

o

i

s

e

R

e

d

u

c

t

i

o

n

t

e

l

p

m

i

S

•

.

y

s

a

e

t

n

e

m

t

3

­A

x

i

s

b

r

a

c

k

e

t

m

a

k

e

s

s

a

u

j

d

INSTALLATION:

Stick the guide pattern on the

1

wall or ceiling.

Drill four holes according to

2

the guide pattern then insert
anchors into the drilled holes.

Fix the surface mount bracket

3

by screws on the ceiling.

Draw out power / video wires

4

to the connecting places.

Connect the dome base to the

5

surface mount bracket by screws.

Adjust desired focus and scene

6

by turning and moving the
3-axis camera bracket by hand.

Put the dome cover over the

7

base.

Fix the dome cover on the base

8

by L-Wrench.

Ceiling

Guide Pattern

Surface Mount
Bracket

Surface Mount
Screw

Dome Base

Tapping Screw

Dome Cover

L-Wrench

SPECIFICATIONS:

Model

Signal System
Scanning System
Scanning Frequency (H
Scanning Frequency (V
Image Sensor
Total / Effective Pixels No.
S / N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity (F1.2)
Electronic Shutter
White Balance
AGC/ BLC/ D&N/ FL
DSS
D-ZOOM
DNR
Input / Output Connector
Operrating Temperature
Storage Temperature
Power Consumption
(Option : AC 24V/DC 12V)
Dome Size (Ø
Weight

)
)

)

NTSC PAL

NTSC : 525 Lines PAL : 625 Lines

15.734kHz 15.625kHz

59.94Hz 50Hz

410K 470K

Fixed Lens (f=2.45mm, 3.8mm, 6mm Selectable)/ Vari-focal Lens

0.3 Lux (color)/ 0.1 Lux (B/W) / 0.008 Lux (DSS On, x32)
1/60 ~ 120,000 Sec. 1 /50 ~ 120,000 Sec.

DC 12V (DC 9.6V~13.2V) / 150mA (Max)

AC 24V (20V~28V) or DC 12V (10V~15V), 3W (Max)

2 : 1 Interlace

1/3 inch SONY IT CCD

50dB Min. (AGC Off)

550 TV Lines

1.0 Vp-p (75 Ohms, composite)

Manual
Internal

Auto

On / Off Selectable

Max 32 times

2 x

AUTO

Power, Video, UTP (Option)

-10°C ~ 45°C

-20°C ~ 65°C

100mm

Approx. 1210g

Dome CameraVandal Proof

Vandal ProofDigital DSP

Digital Slow Shutter DSS

3-Axis

1/3" SONY CCD

.Vari-focal

LENS

ver.0605E

P/N:3810-0062C

.Fixed Lens

Design and specifications are
subject to change without notice.

PRECAUTIONS:

Do not install the camera in

!

extreme temperature conditions.

Do use the camera under conditions
where temperatures are within -10°C
to 45°C.
Be especially careful with ventilation
under high temperatures.

Do not install or use the camera

!

in an environment where the
humidity is high.

It can cause the image quality to be
poor.

Do not disassemble the camera.

!

There are no user-serviceable parts
inside it.

Do not drop the camera or

!

subject them to physical shocks.

It can cause malfunctions to occur.

Note

!

When this camera is installed near
wireless communication devices
that emits strong electromagnetic
field, irregularity such as noise on
the monitor may appear.

1

Tilt rotation: Adjusting the vertical angle.

2

Pan rotation: Adjusting the horizontal angle.

3

Horizontal rotation: Adjusting the horizontal
position of the screen.

NAME AND FUNCTION:

Fixed Lens Type

1

2

Vari-focal Lens Type

4

5

2

Camera Lay-out

4

Focus handle: Focus (Far or Near)

5

Zoom handle: Zoom (Tele or Wide)

CONNECTION:

Connecting to Monitor and Power

DC 12V Power Type

• The wire is polarized.

• Use DC 12V power source.

#

1

3

#

2

No.

Function

#1

Video Output

#2

Power Input

Video

(Yellow)

Power - DC 12V
(Red)

Terminal Color

Yellow

Red

DC 12V(DC9.6V~13.2V), 150mA(Max)

AC 24V/DC 12V Power Type

• The wire is non-polarized.

•

Use AC 24V power source or DC 12V power source.

#

1

1

3

#

2

No.

#1
#2

Function

Video Output
Power Input

IR LED

• Power Consumption: 5W

• IR LED Specification: 850nm / 30° (24EA)

Video

(Yellow)

Power - AC 24V/ DC 12V
(Green)

Terminal Color

Yellow

AC24V(20V~28V)orDC12V(10V~15V), 3W(Max)

Green

(3.8mm Fixed Lens Only)

HEATER: Option

• Power Consumption: 10W

• Operating Temperature Range: -40°C ~ 50°C

Video Output

GND

Remark

1.0 Vp-p

Video Output

GND

Remark

1.0 Vp-p

: Option

90º

Built-in camera
bracket will make user

3-axis

360º

much easier to rotate in
any direction.

CAMERA SET-UP:

Vari-focal Lens Type

a

Service Monitor Connecter:

Use service monitor connector
to set camera angle & focus
when installing.

a

05

5

J

ER

O

T

I

A

E

H

/AUD

VIDEO

(AC 24V)

DC LEVEL

J503

b

TROUBLESHOOTING:

If you have trouble operating your camera, refer to the following.

If the guidelines do not enable you to solve the problem, contact an authorized technician.

The image does not
appear on the screen.

The image on the
screen is dim.

The camera does not work
properly, the surface of the
camera case is hot, and a black
line appears on the screen.

The screen blinks a lot.

J502

AC24V

J501

BLC ON

AGC OFF

D/N OFF

DSS OFF

D/Z ON

FL ON

ON

21 43 65

c

Check the power source for the monitor and camera
and assure that the voltage and polarity are properly
connected and being supplied correctly.

Check if the lens is stained. If dirty, clean the lens with
a soft, clean cloth.
Adjust the Back Focus of the lens again.

Check if you have connected the camera to a proper
power source and If there is no problem with the power,
turn the unit off immediately and seek assistance from
our After Service department.

Check if the camera is pointed toward the sun or a
fluorescent lamp.
Adjust the angle or location of the camera if too much
light is coming into the screen.

b

DC Level Adjustment V.R

c

Function Selection Switch:

•

BLC(Back Light Compensation)

ON/OFF

•AGC(Auto Gain Control) ON/OFF

•D/N(Day & Night) ON/OFF

•

DSS(Digital Slow Shutter) ON/OFF

•D/Z(Digital Zoom) ON/OFF

•FL(Flickerless) ON/OFF

CAUTION

the switching of D&N doesn't work.
Because the D&N switching function
is related in AGC level.

: In case of AGC off,

360º