CNB SSM2065PW User Manual
Xpeed Mini Outdoor Speed Dome Camera Series
Outdoor Mini Speed Dome Camera Series / SM2000 Series
INSTRUCTION MANUAL Ver 1.0
www.cnbtec.com
(3810-0170D)
This lightning flash with arrowhead symbol is intended to alert the user to the
presence of un-insulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
www.cnbtec.com
2
NOTICE
Xpeed Mini Outdoor Speed Dome Camera Series
CONTENTS
Xpeed Mini Outdoor Speed Dome Camera Series
▣ Important Safeguard
1. Read Instructions
Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments/Accessories
Do not use attachments or accessories unless recommended by the appliance manuf acturer as they may
cause hazards, damage product and void warranty.
4. Water and Moisture
Do not use this product near water or moisture.
5. Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly
installed product may fall, causing serious injury to a child or adult, and damage to the product. Use only with
a mounting device recommended by the manufacturer, or sold with the product. To insure proper mounting,
follow the manufacturer's instructions and use only mounting accessories recommended by manufacturer.
6. Power source
This product should be operated only from the type of power source indicated on the marking label.
▣ Precautions
■ Operating
z Before using, make sure power supply and others are properly connected.
z While operating, if any abnormal condition or malfunction is observed, stop using the camera
immediately and then contact your local dealer.
■ Handling
z Do not disassemble or tamper with parts inside the camera.
z Do not drop or subject the camera to shock and vibration as this can damage camera.
z Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your
quality of camera.
■ Installation and Storage
z Do not install the camera in areas of extreme temperature, which exceed the allowable range.
z Avoid installing in humid or dusty places.
z Avoid installing in places where radiation is present.
z Avoid installing in places where there are strong magnetic fields and electric signals.
z Avoid installing in places where the camera would be subject to strong vibrations.
z Never expose the camera to rain and water.
1. Introduction
Features ………………………………………………………………………………………………………………… 5
Product & Accessories ……………………….………………………………………………………………………. 7
Parts Name & Functions ..…………………….……………………………………………………………………… 8
2. Installation
DIP Switch Setup ……………………………………………………………………………………………………… 9
Direct Installation on the Ceiling …………………………………………………………………………………… 11
Installation of Mount Gasket ………………………………………………………………………………………… 12
Installation using Pendant Mount Bracket .....…………………………………………………………………….. 13
Installation using Wall Mount Bracket ……………………………………………………………………………… 14
Cabling ………………………………………………………………………………………………………………… 16
3. Operation
Check points before Operation …………………………………………………………………………………….. 18
Preset and Pattern Function Pre-Check …………………………………………………………………………… 18
Starting OSD Menu …………………………………………………………………………………………………… 18
Reserved Preset ………………………………………………………………………………………………………. 18
Preset ………………………………………………………………………………………………………………...... 19
Swing ………………………………………………………………………………………………………………...... 19
Pattern ..……………………………………………………………………………………………………………...... 20
Group ………………………………………………………………………………………………………………...... 21
Other Functions …..………………………………………………………………………………………………...... 22
OSD Display of Main Screen ……………………………………………………………………………………...... 23
4. Menu
General Rules of Key operation for Menu .……………………………………………………………………...... 24
Main Menu ………………………………….……………………………………………………………………....... 24
Display Setup .……………………………….……………………………………………………………………...... 25
Privacy Zone Mask Setup .................…….……………………………………………………………………...... 26
Zoom Camera Setup .……………………….……………………………………………………………………...... 27
Motion Setup .……………………………….……………………………………………………………………...... 29
Preset Setup ……………………………….…………………………………………………………………………... 31
Swing Setup ………………………………….……………………………………………………………………...... 33
Pattern Setup .……………………………….……………………………………………………………………....... 34
Group Setup ..……………………………….……………………………………………………………………....... 35
System Initialize …………………………….……………………………………………………………………....... 37
5. Specifications
SM2065N(P) ………………………………….……………………………………………………………………...... 38
Dimension ..………………………………….……………………………………………………………………...... 39
www.cnbtec.com
3
www.cnbtec.com
4
1. INTRODUCTION
Xpeed Mini Outdoor Speed Dome Camera Series
1. INTRODUCTION
Xpeed Mini Outdoor Speed Dome Camera Series
▣ Fe at u r es
Camera Specifications
z CCD Sensor : 1/4" Interline Transfer CCD
z Zoom Magnification : 10x Optical Zoom, 10x Digital Zoom (Max. 100x Zoom) Æ Model SM2065N(P)
z Day & Night Function
z Various Focus Mode : Auto-Focus / Manual Focus / Semi-Auto Focus.
z Independent & Simultaneous Camera Characteristic Setup in Preset operation
Powerful Pan/Til t Functions
z Max. 360°/sec high speed Pan/Tilt Movement.
z Using Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path. As a result, time to
target view is reduced dramatically and the video on the monitor is very natural to watch.
z For jog operation using a controller, since ultra slow speed 0.05°/sec can be reached, it is very easy to
locate camera to desired target view. Additionally it is easy to move camera to a desired position with
zoom-proportional pan/tilt movement.
Preset, Pattern, Swing, Group, Privacy Mask and More…
z Max. 127 Presets are assignable and characteristics of each preset can be set up independently, such as
White Balance, Auto Exposure, Label and so on.
z Max. 8 set of Swing action can be stored. This enables to move camera repetitively between two preset
positions with designated speed.
z Max. 4 of Patterns can be recorded and played back. This enables to move camera to follow any trajectory
operated by joystick as closely as possible.
z Max. 8 set of Group action can be stored. T his enables to move camera repetitively with combination of
Preset or Pattern or Swing. A Group is composed of max. 20 entities of Preset/Pattern/Swings.
z Privacy Masks are assignable, not to intrude on other’s privacy. (4 Privacy Zones)
Æ Only available with 10x Models.
PTZ(Pan/Tilt/Zoom) Control
z With RS-485 communication, max. 255 of cameras can be controlled at the same time.
z Pelco-D or Pelco-P protocol can be selected as a control protocol in the current version of firmware.
OSD(On Screen Display) Menu
z OSD menu is provided to display the status of camera and to configure the functions interactively.
z The information such as Camera ID, Pan/Tilt Angle, Alarm Input and Preset can be displayed on screen.
Alar m I/O Functions
z 4 alarm sensor Inputs and 1 alarm output relay are available.
z To reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo coupler.
z The signal range of sensor input is from DC 5.0 to 12.0 volts to adopt various applications.
z Relay output is able to connect. (max. 125VAC, 0.5A or 24VDC, 1A)
z If an external sensor is activated, camera can be set to move to the corresponding Preset position.
Easy Installation and Perfect Outdoor Environment Compatibility
z Fans and heaters are built-in in camera for cold and hot temperature environment.
Also idealistic mechanical design protects camera from water and dust. (IP66)
z It is easy to install and maintain camera with terminal for cable connection in brackets.
www.cnbtec.com
5
www.cnbtec.com
6
1. INTRODUCTION
Xpeed Mini Outdoor Speed Dome Camera Series
1. INTRODUCTION
Xpeed Mini Outdoor Speed Dome Camera Series
▣ Product & Accessories
Basic Components
Camera Bracket & Bracket Accessories
Other Components (available to be ordered separately)
▣ Parts Name & Functions
① Dome Cover Do not detach protection vinyl from dome cover before finishing all
installation process to protect dome cover from scratches or dust.
② DIP Switch Sets up camera ID and protocol.
③ Main Body Cable Enables signals and power to come and go between main body and mount
bracket.
④ Drop Prevention Spring This part keeps the camera from dropping during installation and
maintenance. After install the Bracket, please, hang the spring to the drop
prevention hook of main body as shown in picture for further tasks.
⑤ Fuse If the fuse is burnt to protect your came from over-current damage, the fuse
have to be replace with new one. The fuse specification is 250V, 2A.
However, we recommend consulting with supplier to remove the cause of
over-current.
⑥ Lockup Screw After assembling main body to bracket, screw main body to bracket to
protect them from separation by vibration and so on.
⑦ Cablling Terminal Block During installation, Power, Video, Ciommunication, Alarm I/O cables are
connected on to this cabling terminal block.
⑧ Mold Line Mark to assemble main body to bracket.
www.cnbtec.com
7
www.cnbtec.com
8
2. INSTALLATION
Xpeed Mini Outdoor Speed Dome Camera Series
2. INSTALLATION
Xpeed Mini Outdoor Speed Dome Camera Series
▣ DIP Switch Setup
Before you install the camera, you should set the DIP switches to configure the camera ID, communication protocol.
Camera ID Setup
z ID number of camera is set using dip switch. The example is shown
bellow.
Pin 1 2 3 4 5 6 7 8
ID Value 1 2 4 8 16 32 64 128
ex) ID=5 on off on off off off off off
ex) ID=10 off on off on off off off off
z The range of ID is 1~255. Do not u se 0 as camera ID. Factory default of
Camera ID is 1.
z If you want to control a certain camera, you must match the camera ID
with Cam ID setting of DVR or Controller.
Communication Protocol Setup
z Select the appropriate Protocol with DIP switch combination.
z If you want to control using DVR or P/T controller, their protocol must be
z If you changed camera protocol by changing DIP S/W, the change will be
z Factory default of protocol is “Pelco-D, 2400 bps”.
z Reserved for supplier.
Switch State
P0
(Pin 1)
OFF OFF OFF PELCO-D, 2400 bps
ON OFF OFF PELCO-D, 9600 bps
OFF ON OFF PELCO-P, 4800 bps
ON ON 0FF PELCO-P, 9600 bps
identical to camera. Otherwise, you can not control the camera.
effective after you reboot the camera.
P1
(Pin 2)
Others Reserved
P3
(Pin 3)
Protocol
www.cnbtec.com
9
www.cnbtec.com
10
2. INSTALLATION
Xpeed Mini Outdoor Speed Dome Camera Series
2. INSTALLATION
Xpeed Mini Outdoor Speed Dome Camera Series
Termination Switch Setting
Termination switch(Pin 4) is used in cases listed below.
z Long-distance communication between the controller and the
camera (1-to-1 connection)
When the connecting distance between the two units is especially long,
communication errors may occur due to the impedance of transmission
cable. In this case, set the termination switch of both units to ON.
z Controlling multiple cameras (Multiple connection)
The camera may not operate correctly if multiple cameras are connected
and controlled. In this case, set the termination switch of the controller
and the last connected camera to ON and the switch of other cameras is
OFF.
Ex) Using the Terminating Resistance
▣ Installation of Mount Gasket
① Pull out the rounded
② Make a incision in the
③ Have the cables run
④ Tie up the rubber
rubber rubber tube.
(+) form at the upper
part of the rubber tube.
through the rubber tube
as illustrated on the
picture.
tube in the middle.
www.cnbtec.com
11
⑤ Assemble the gasket to
the bracket and
www.cnbtec.com
12
complete the installation
after put the tied tube
back to the orginal
position.
2. INSTALLATION 2. INSTALLATION
Xpeed Mini Outdoor Speed Dome Camera Series
2. INSTALLATION
Xpeed Mini Outdoor Speed Dome Camera Series
▣ Installation using the Wall Mount Bracket
z Before install, you must have bracket with mount gasket.
z Refer to the Installation of mount gasket section.
① Install Wall Mount Bracket on wall
③ Hook up “Drop Prevention Spring” on main body to
prevent camera from unexpected drop and connect
Main Body Cable to Main Body Connector in Wall
Mount Bracket.
② Wire cables to terminal blocks on the PCB in Wall
Mount Bracket.
④ Line up the mold lines and assemble main body to
Wall Mount Bracket.
▣ Installation using Pendant Mount Bracket
z Before install , you must have bracket with mount gasket.
z Refer to the Installation of mount gasket section.
① To pass cables to upside of ceiling, Please make a
hole with 50 ~ 60mm diameter on the ceiling
panel and attach the Ceiling mount bracket on it.
③ Hook up “Drop Prevention Spring” on main body to
prevent camera from unexpected drop and connect
Main Body Cable to Main Body Connector in Ceiling
Mount Bracket.
② Wire cables to terminal blocks on the PCB in
Ceiling Mount Brakcket.
④ Insert the main body into the pendant mount
bracket with the molding lines on each part
being aligned and turning clockwise.
⑤ Turn main body on its axis in CW(Clockwise)
direction and after assembling them, screw main
body to Wall Mount Bracket to protect them from
separation by vibration or others.
www.cnbtec.com
13
www.cnbtec.com
14
Loading...