Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments / Accessories
Do not use attachments or accessories unless recommended by the appliance manufacturer as they may
cause hazards, damage product and void warranty.
4. Water and Moisture
Do not use this product near water or moisture.
5. Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly
installed product may fall, causing serious injury to a child or adult, and damage to the product. Use only
with a mounting device recommended by the manufacturer, or sold with the product. To insure proper
mounting, follow the manufacturer's instructions and use only mounting accessories recommended by
manufacturer.
6. Power source
This product should be operated only from the type of power source indicated on the marking label.
Precautions
Operating
z Before using, make sure power supply and others are properly connected.
z While operating, if any abnormal condition or malfunction is observed, stop using the camera
immediately and then contact your local dealer.
Handling
z Do not disassemble or tamper with parts inside the camera.
z Do not drop or subject the camera to shock and vibration as this can damage camera.
z Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your
quality of camera.
Installation and Storage
z Do not install the camera in areas of extreme temperature, which exceed the allowable range.
z Avoid installing in humid or dusty places.
z Avoid installing in places where radiation is present.
z Avoid installing in places where there are strong magnetic fields and electric signals.
z Avoid installing in places where the camera would be subject to strong vibrations.
z Never expose the camera to rain and water.
ini Speed Dome Camera/SM1000 Series
3
Page 4
M
CONTENTS
1
○
Introduction
Feat ures
Product & Accessories
Parts Name & Functions
2
○
Installation
DIP Switch Setup 9
Direct Installation on the Ceiling
Installation using Ceiling Mount Bracket
Installation using Wall Mount Bracket
Cabling
3
○
Operation
Check points before Operation
Preset and Pattern Function Pre-Check
Start OSD Menu
Reserved Preset
Preset
Swing
Pattern
Group
Other Functions
OSD Display of Main Screen
4
○
How to use OSD Menu
General Rules of Key operation for Menu
Main Menu
Display Setup
Privacy Zone Mask Setup
Camera Setup
Motion Setup
Preset Setup
Swing Setup
Pattern Setup
Group Setup
System Initialize
○5 Specifications
Dimension
5
7
8
11
12
14
16
18
18
19
19
20
20
21
22
23
24
25
25
26
27
28
30
32
34
35
36
38
39
ini Speed Dome Camera/SM1000 Series
4
Page 5
M
INTRODUCTION
Features
Camera Specifications
z CCD Sensor : 1/4" Interline Transfer CCD
z Zoom Magnification : × 10 Optical Zoom, × 10 Digital Zoom (Max × 100 Zoom) Æ SM1063(5)N(P)
z Day & Night Function
z Various Focus Mode : Auto-Focus / Manual Focus / Semi-Auto Focus.
z Independent & Simultaneous Camera Characteristic Setup in Preset operation
Powerful Pan/Tilt Functions
z Max. 360°/sec high speed Pan/Tilt Motion
z Using Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path. As a result,
time to target view is reduced dramatically and the video on the monitor is very natural to watch.
1
z For jog operation using a controller, since ultra slow speed 0.05°/sec can be reached, it is very easy
to locate camera to desired target view. Additionally it is easy to move camera to a desired position
with zoom-proportional pan/tilt movement.
Preset, Pattern, Swing, Group, Privacy Mask and More…
z MAX. 127 Presets are assignable and characteristics of each preset can be set up independently,
such as White Balance, Auto Exposure, Label and so on.
z Max. 8 set of Swing action can be stored. This enables to move camera repetitively between two
preset positions with designated speed.
z Max. 4 of Patterns can be recorded and played back. This enables to move camera to follow any
trajectory operated by joystick as closely as possible.
z Max. 8 set of Group action can be stored. This enables to move camera repetitively with
combination of Preset or Pattern or Swing. A Group is composed of max. 20 entities of
Preset/Pattern/Swings.
z Privacy Masks are assignable, not to intrude on other’s privacy. (4 Privacy Zones)
PTZ(Pan/Tilt/Zoom) Control
z With RS-485 communication, max. 255 of cameras can be controlled at the same time.
z Pelco-D or Pelco-P protocol can be selected as a control protocol in the current version of firmware.
ini Speed Dome Camera/SM1000 Series
5
Page 6
M
OSD(On Screen Display) Menu
z OSD menu is provided to display the status of camera and to configure the functions interactively.
z The information such as Camera ID, Pan/Tilt Angle, Alarm Input and Preset can be displayed on
screen.
Alarm I/O Functions
z 4 alarm sensor Inputs are available.
z To reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo
coupler.
z The signal range of sensor input is from DC 5.0 to 12.0 volts to adopt various applications.
z If an external sensor is activated, camera can be set to move to the corresponding Preset position.
Reserved Presets for Special Purpose
INTRODUCTION
1
z Most camera characteristics can be set up easily and directly with reserved preset, not entering
into OSD menu. For more information, refer to “Reserved Preset” in this manual.
ini Speed Dome Camera/SM1000 Series
6
Page 7
M
Product & Accessories
Product & Accessories
z Main Body z Clear Bubble z Screws & Terminal Block
INTRODUCTION
1
Options
& Guide Pattern & Adaptor(Option)
z Ceiling Mount Bracket z Wall Mount Bracket
ini Speed Dome Camera/SM1000 Series
7
Page 8
M
Parts Name & Functions
INTRODUCTION
1
z Main Unit / Surface Mount Bracket z Back of Main Unit
z Dome Cover Do not detach protection vinyl from dome cover before finishing all
installation process to protect dome cover from scratches or dust.
z Surface Mount Bracket This is used to install the camera directly on the ceiling. After
separating this cover first and then attach this directly to ceiling.
Camera must be assembled at the last stage.
Do not use this bracket when installing camera on the wall with wall
mount bracket or on the ceiling with ceiling mount bracket.
z Lockup Screw Fixes main unit to surface mount bracket.
z Cabling Terminal Block During installation, Power, Video, Communication, Alarm Input cables
are connected on to this cabling terminal block.
z DIP Switch Adjusts camera ID and protocols.
ini Speed Dome Camera/SM1000 Series
8
Page 9
M
n
INSTALLATION
DIP Switch Setup
Before you install the camera, you should set the DIP switches to configure the camera ID, communication
protocol.
Communicatio
Protocol
Camera ID
2
Camera ID Setup
ON
ON
123456
ON
the Manual
78
OPTIONS
Refer to
PAL
NTSC
ADDRESS (ID)
1248 16 32 64 128
00000000
z ID number of camera is set using dip switch. The example is shown
bellow.
Pin 1 2 3 4 5 6 7 8
ID Value 1 2 4 8 16 32 64 128
ex) ID=5 on off on off off off off off
ex) ID=10 off on off on off off off off
z The range of ID is 1~255. Do not use 0 as camera ID. Fact o r y
default of Camera ID is 1.
z If you want to control a certain camera, you must match the camera
ID with Cam ID setting of DVR or Controller.
ini Speed Dome Camera/SM1000 Series
9
Page 10
M
INSTALLATION
Communication Protocol Setup
ON
ON
1234
z Select the appropriate Protocol with DIP switch combination.
Switch State
P0
(Pin 1)
P1
(Pin 2)
Protocol
2
Reserved for Supplier
ON
ON
1234
OFF OFF PELCO-D, 2400 bps
ON OFF PELCO-D, 9600 bps
OFF ON PELCO-P, 4800 bps
ON ON PELCO-P, 9600 bps
z If you want to control using DVR or P/T controller, their protocol must
be identical to camera. Otherwise, you can not control the camera.
z If you changed camera protocol by changing DIP S/W, the change
will be effective after you reboot the camera.
z Factory default of protocol is “Pelco-D, 2400 bps”.
z Since Pin 3 ~ Pin 4 is only for supplier, DO NOT CHANGE THESE ITS
ORIGINAL STATE. If you change one of these, proper operation can
not be achieved.
~ Pin 3 PAL / NTSC system selection of Camera. DO NOT
CHANGE THIS PIN.
~ Pin 4 Factory default is ON state. This pin is used for system
firmware upgrade. DO NOT CHANGE THIS PIN
ini Speed Dome Camera/SM1000 Series
.
10
Page 11
M
Direct Installation on the Ceiling
① To pass cables to upside of ceiling, please, make
about 50~60mm hole on the ceiling panel.
② Detach the marked part from the rubber gasket
and srew the surface mount bracket to the ceiling
with fixing screws.
2
You can use “Guide Pattern” for the
making holes.
③ Wire cables to terminal block and connect the
terminal blocks to main unit.
④ Insert the main body into the surface mount
bracket with the molding lines on each part being
aligned and turning clockwise.
ini Speed Dome Camera/SM1000 Series
11
Page 12
M
INSTALLATION
2
⑤ Insert the fixing screw tightly and detach the
protection vinyl from dome cover.
Installation using Ceiling Mount Bracket
① Screw ceiling mount bracket to ceiling with
screws.
② Detach the marked part from the rubber gasket
and srew the mounting base to the ceiling mount
bracket with fixing screws.
You can use “Guide Pattern” for the
making holes.
ini Speed Dome Camera/SM1000 Series
12
Page 13
M
INSTALLATION
2
③ Wire cables to terminal block and connect the
terminal blocks to main unit.
⑤ Insert the fixing screw tightly and detach the
protection vinyl from dome cover.
④ Insert the main body into the ceiling mount
bracket with the molding lines on each part being
aligned and turning clockwise.
ini Speed Dome Camera/SM1000 Series
13
Page 14
M
Installation using Wall Mount Bracket
① Screw wall mount bracket to ceiling with 3
screws.
You can use “Guide Pattern” for the
making holes.
② Detach the marked part from the rubber gasket
and srew the mounting base to the wall mount
bracket with fixing screws.
INSTALLATION
2
③ Wire cables to terminal block and connect the
terminal blocks to main unit.
④ Insert the main body into the wall mount bracket
z Please, check the voltage and current capacity of rated power carefully. Rated power is indicated in the
back of main unit.
Rated Power Input Voltage Range Current Consumption
DC 12V DC 11V ~ 18V 0.8 A
AC 24V AC 17V ~ 29V 0.4 A
RS-485 Communication
z For PTZ control, connect this line to keyboard and DVR. To control multiple cameras at the same time,
RS-485 communication lines of them is connected in parallel as shown below.
ini Speed Dome Camera/SM1000 Series
16
Page 17
M
Video Connection
z Connect with BNC coaxial cable.
Alarm Input Connection
z Sensor Input
INSTALLATION
2
Internal
Before connecting sensors, check driving voltage and output signal type of the sensor. Since output
signal types of the sensors are divided into Open Collector and Voltage Output type in general, the
cabling must be done properly after considering these typed.
Signal Description
IN COM+ Connect (+) cable of electric power source for Sensors to this port as
IN1−, IN2 −, I N 3−, IN4−Connect output of sensors for each port as shown in the circuit above.
IN COM+
IN 1-
IN 4-
shown in the circuit above.
Sensor 1 Output
Sensor 4 Output
+5V~12V
+
+
+
-
-
-
If you want to use Alarm Input, the types of sensor must be selected in OSD menu. The sensor types are
Normal Open and Normal. If sensor type is not selected properly, the alarm can be activated reversely.
~ Normal Open Output Voltage is high state when sensor is activated
~ Normal Close Output Voltage is high state when sensor is not activated
ini Speed Dome Camera/SM1000 Series
17
Page 18
M
OPERATION3
Check points before operation
z Before power is applied, please check the cables carefully.
z The camera ID of the controller must be identical to that of the target camera. The camera ID can be checked
by reading DIP switch of the camera.
z If your controller supports multi-protocols, the protocol must be changed to match to that of the camera.
z If you changed camera protocol by changing DIP switch, the change will be effective after you reboot the
camera.
z Since the operation method can be different for each controller available, refer to the manual for your
controller if camera can not be controlled properly. The operation of this manual is based on the standard
Pelco® Controller.
Preset and Pattern Function Pre-Check
z Check how to operate preset and pattern function with controller or DVR in advance to operate camera
function fully when using controller or DVR.
z Refer to the following table when using standard Pelco® protocol controller.
< Go Preset > Input [Preset Number] and press [Preset] button shortly.
< Set Preset > Input [Preset Number] and press [Preset] button for more than 2 seconds.
< Run Pattern > Input [Pattern Number] and press [Pattern] button shortly.
< Set Pattern > Input [Pattern Number] and press [Pattern] button for more than 2 seconds.
z If controller or DVR has no pattern button or function, use shortcut keys with preset numbers. For more
information, refer to “Reserved Preset” in this manual.
ini Speed Dome Camera/SM1000 Series
18
Page 19
M
OPERATION
Starting OSD Menu
z Function Using the OSD menu, Preset, Pattern, Swing, Group and Alarm Input function can be
configured for each application.
z Enter Menu <Go Preset> [95]
Reserved Preset
z Description Some Preset numbers are reserved to special functions.
z Function <Go Preset> [95] : Enters into OSD menu
<Go Preset> [131~134] : Runs Pattern Function 1 ~ 4
<Go Preset> [141~148] : Runs Swing Function 1 ~ 8
3
<Go Preset> [151~158] : Runs Group Function 1 ~ 8
<Go Preset> [170] : Sets Camera BLC Mode to OFF
<Go Preset> [171] : Sets Camera BLC Mode to ON
<Go Preset> [174] : Sets Camera Focus Mode to AUTO
<Go Preset> [175] : Sets Camera Focus Mode to Manual
<Go Preset> [176] : Sets Camera Focus Mode to SEMI-AUTO
<Go Preset> [177] : Sets Day & Night Mode to AUTO
<Go Preset> [178] : Sets Day & Night Mode to NIGHT
<Go Preset> [179] : Sets Day & Night Mode to DAY
<Go Preset> [190] : Sets OSD Display Mode to AUTO (Except Privacy Mask)
<Go Preset> [191] : Sets OSD Display Mode to OFF (Except Privacy Mask)
<Go Preset> [192] : Setting OSD Display Mode to ON (Except Privacy Mask)
<Go Preset> [193] : Sets all Privacy Mask Display to OFF
<Go Preset> [194] : Sets all Privacy Mask Display to ON
ini Speed Dome Camera/SM1000 Series
19
Page 20
M
OPERATION
Preset
z Function Max. 127 positions can be stored as Preset position. The Preset number can be assigned
from 1 to 128, but 95 is reserved for starting OSD menu.
Camera characteristics (i.e. White Balance, Auto Exposure) can be set up independently
for each preset. Label should be blank and "Camera Adjust" should be set to "GLOBAL" as
default. All characteristics can be set up in OSD menu.
z Set Preset<Set Preset> [1~128]
z Run Preset<Go Preset> [1~128]
z Delete Preset To delete Preset, use OSD menu.
Swing
3
z Function By using Swing function, you can make camera to move between 2 Preset positions
repeatedly. When swing function runs, camera moves from the preset assigned as the 1st
point to the preset assigned as the 2nd point in CW(Clockwise) direction. Then camera
moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in
CCW(Counterclockwise) direction.
1
1st Preset
n
o
i
t
c
e
r
i
D
W
C
W
C
C
2
i
D
c
e
r
n
o
i
t
2nd Preset
In case that the preset assigned as the 1st point is same as the preset assigned as the 2nd
point, camera turns on its axis by 360° in CW(Clockwise) direction and then it turns on its
axis by 360° in CCW(Counterclockwise) direction.
Speed can be set up from 1°/sec to 180°/sec.
z Set SwingTo set Swing, use OSD menu.
z Run SwingMethod 1) <Run Pattern> [Swing NO.+10]
Method 2) <Go Preset> [Swing NO.+140]
ex) Run Swing 3 : <Run Pattern> [13]
ex) Run Swing 3 : <Go Preset> [143]
z Delete Swing To delete Swing, use OSD menu.
ini Speed Dome Camera/SM1000 Series
20
Page 21
M
OPERATION
Pattern
z Function Pattern Function is that a camera memorizes the path (mostly curve path) by joystick of
controller for assigned time and revives the path exactly as it memorized.
4 Patterns are available and Maximum 1200 communication commands can be stored in
a pattern.
z Set Pattern Pattern can be created by one of following two methods.
Method 1) <Set Pattern> [Pattern NO.]
{ Pattern editing screen is displayed as bellow.
EDIT PATTERN 1
3
[NEAR:SAVE /FAR:DELETE]
0/0/x1/N
{ Movement by Joystick and preset movement can be memorized in a pattern.
{ The rest memory size is displayed in progress bar.
{ To save the recording, press NEAR key and to cancel, press FAR key.
Method 2) OSD Using OSD Menu: See the section “How to use OSD Menu”.
z Run Pattern Method 1) <Run Pattern> [Pattern NO.]
Method 2) <Go Preset> [Pattern NO.+130]
z Delete Pattern To delete Pattern, use OSD menu.
ex) Run Pattern 2 : <Run Pattern> [2]
ex) Run Pattern 2: <Go Preset> [132]
ini Speed Dome Camera/SM1000 Series
21
Page 22
M
Group
z Function The group function allows running sequence of Presets, Pattern and/or Swings. Max 8
group can be stored. Each group can have max 20 action entities which can be preset,
pattern or swing. Preset speed can be set up and the repeat number of Pattern & Swing
can be set up in Group setup. Dwell time between actions can be set up also.
Dwell Time
Preset 1Pattern 1Swing 1
OPERATION
3
z Set GroupUse OSD Menu to create a Group.
z Run GroupMethod 1) <Run Pattern> [Group NO.+20]
Method 2) <Go Preset> [Group NO.++150]
z Delete Group To delete Group, use OSD menu.
Max 20 Entities
ex) Run Group 7 : <Run Pattern> [27]
ex) Run Group 7 : <Go Preset> [157]
ini Speed Dome Camera/SM1000 Series
22
Page 23
M
OPERATION
Other Functions
z Power Up Action This function enables to resume the last action executed before power down. Most of
actions such as Preset, Pattern, Swing and Group are available for this function but Jog
actions are not available to resume.
z Auto Flip In case that tilt angle arrives at the top of tilt orbit (90°), zoom module camera keep
moving to opposite tilt direction (180°) to keep tracing targets. As soon as zoom module
camera passes through the top of tilt direction(90°), images should be reversed
automatically and F appears in screen. If this function is set to OFF, tilt movement range
is 0 ~ 95°.
z Parking Action This function enables to locate the camera to specific position automatically if operator
doesn’t operate the controller for a while. The Park Time can be defined as an interval
from 1 minute to 4 hours.
3
z Alarm Input 4 Alarm Inputs are used. If an external sensor is activated, camera can be set to move to
corresponding preset position. It is noted that the latest alarm input is effective if
multiple sensors are activated.
z Privacy Zone Mask To protect privacy, MAX. 4 Privacy Masks can be created on the arbitrary position to
hide objects such as windows, shops or private house. With Spherical Coordinates
system, powerful Privacy Zone Mask function is possible.
z GLOBAL/LOCAL
Image Setup
z SemiAuto Focus
WB(White Balance) and AE(Auto Exposure) can be set up independently for each
preset. There are 2 modes, "Global" mode & "Local" mode. The Global mode means that
WB or AE can be set up totally and simultaneously for all presets in "ZOOM CAMERA
SETUP" menu. The Local mode means that WB or AE can be set up independently or
separately for each preset in each preset setup menu. Each Local WB/AE value should
activate correspondingly when camera arrives at each preset location.
During jog operation, Global WB/AE value should be applied. All Local WB/AE value
do not change although Global WB/AE value changes.
This mode exchanges focus mode automatically between Manual Focus mode and Auto
Focus mode by operation. Manual Focus mode activates in preset operation and Auto
Focus mode activates during jog operation. With Manual mode at presets, Focus data is
memorized in each preset in advance and camera calls focus data in correspondence
with presets as soon as camera arrives at a preset. It should shorten time to get focuses.
Focus mode changes to Auto Focus mode automatically when jog operation starts.
ini Speed Dome Camera/SM1000 Series
23
Page 24
M
OPERATION
OSD Display of Main Screen
3
Preset Label
Image Flip
Camera ID
LABEL12345 PRESET1
F I:1--4
CAM 1 15/4/x1/N
P/T/Z Information
Action Title
Alarm Information
z P/T/Z Information Current Pan/Tilt angle in degree, zoom magnification and a compass direction.
z Camera ID Current Camera ID(Address).
z Action Title
Followings are possible Action Titles and their meaning.
"SET PRESET ×××" When Preset ××× is stored
"PRESET ×××" When camera reach to Preset ×××
"PATTERN ×" When Pattern × is in action
"SWG×/PRESET ×××" When Swing × is in action
"UNDEFINED" When undefined function is called to run
z Preset Label The Label stored for specific Preset.
z Alarm Input This information shows current state of Alarm Input. If an Input point is ON state it will
show a number corresponding to each point. If an Input point is OFF state, '-' will be
displayed.
Ex) Point 2 & 3 of inputs are ON, OSD will show as below
I:-23-
z Image Flip Shows that images are currently reversed by Auto Flip Function.
ini Speed Dome Camera/SM1000 Series
24
Page 25
M
HOW TO USE OSD MENU
General Rules of Key Operation for Menu
z The menu items surrounded with ( ) always has its sub menu.
z For all menu level, to go into sub menu, press NEAR key.
z To go to up-one-level menu, press FARkey.
z To move from items to item in the menu, use joystick in the Up/Down or Left/Right.
z To change a value of an item, use Up/Down of the joystick in the controller.
z Press NEAR key to save values and Press FAR key to cancel values.
Main Menu
4
SPEED DOME CAMERA
----------------------- <SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME CAMERA SETUP>
<SYSTEM INITIALIZE>
EXIT
z System Information Displays system information and configuration.
z Display Setup Enable/Disable of OSD display on Main
Screen.
z Dome Camera Setup
z System Initialize Initializes system configuration and sets all
Configure various functions of this camera.
data to factory default configuration.
ini Speed Dome Camera/SM1000 Series
25
Page 26
M
Display Setup
HOW TO USE OSD MENU
4
DISPLAY SETUP
----------------------- CAMERA ID ON
PTZ INFORMATION AUTO
ACTION TITLE AUTO
PRESET LABEL AUTO
ALARM INPUT AUTO
<SET NORTH DIRECTION>
<PRIVACY ZONE>
BACK
EXIT
Compass Direction Setup
SET NORTH DIRECTION
------------------------
This menu defines Enable/Disable of OSD display on Main Screen. If an
item is set to be AUTO, the item is displayed only when the value of it is
changed.
z Camera ID [ON/OFF]
z PTZ Information [ON/OFF/AUTO]
z Action Title [ON/OFF/AUTO]
z Preset Label [ON/OFF/AUTO]
z Alarm Input [ON/OFF/AUTO]
Set North to assign compass direction as criteria. Move camera and
press NEAR button to save.
MOVE TO TARGET POSITION
[NEAR:SAVE /FAR:CANCEL
ini Speed Dome Camera/SM1000 Series
26
Page 27
M
PRIVACY ZONE MASK Setup
HOW TO USE OSD MENU
PRIVACY ZONE
----------------------- MASK NO 1
UNDEFINED
DISPLAY OFF
CLEAR MASK CANCEL
<EDIT MASK>
BACK
EXIT
Select area in image to mask.
z Mask No [1~4]
z Display [ON/OFF]
Select Mask number. If the selected mask has
already data, camera moves as it was set.
Otherwise, “UNDEFINED” will be displayed
under “Mask NO”.
Sets if camera makes mask shows or not on
images.
4
Privacy Zone Area Setup
EDIT MASK 1
------------------------
MOVE TO TARGET POSITION
[NEAR:SELECT/FAR:CANCEL]
Privacy Zone Size Adjustment
EDIT MASK 1
------------------------
z Clear Mask [CANCEL/OK]
Deletes data in the selected mask NO.
Move camera to area to mask. Then the menu to adjust mask size will be
displayed.
Adjust mask size. Use joystick or arrow buttons to adjust mask size.
z (Left/Right) Adjusts mask width.
z (Up/Down) Adjusts mask height.
[ :ADJUST MASK WIDTH]
[ :ADJUST MASK HEIGHT]
[NEAR:SAVE /FAR:CANCEL]
ini Speed Dome Camera/SM1000 Series
27
Page 28
M
CAMERA SETUP
HOW TO USE OSD MENU
4
ZOOM CAMERA SETUP
----------------------- FOCUS MODE SEMIAUTO
DIGITAL ZOOM ON
LINE LOCK OFF
<WHITE BALANCE SETUP>
<AUTO EXPOSURE SETUP>
BACK
EXIT
Setup the general functions of zoom camera module.
z Focus Mode [AUTO/MANUAL/SEMIAUTO]
Sets camera focus mode.
{ SEMIAUTO Mode
This mode exchanges focus mode automatically
between Manual Focus mode and Auto Focus mode.
z Digital Zoom [ON/OFF]
z Line Lock [ON/OFF]
Manual Focus mode activates in preset operation
and Auto Focus mode activates when jog operation
starts.
With Manual mode at presets, Focus data is
memorized in each preset in advance and camera
calls focus data in correspondence with presets as
soon as camera arrives at a preset.
Sets digital zoom function to ON/OFF. If this is set to
OFF, optical zoom function runs but zoom function
stops at the end of optical zoom magnification.
If Line lock sync is ON, video signal is synchronized
with AC power. Video can be fluctuated after
setting is changed.
White Balance Setup
WB SETUP - GLOBAL
----------------------- WB MODE AUTO
RED ADJUST -- BLUE ADJUST ---
BACK
EXIT
ini Speed Dome Camera/SM1000 Series
z WB Mode [AUTO/MANUAL]
In Manual mode, Red and Blue level can be set
up manually
z Red Adjust [10~60]
z Blue Adjust [10~60]
28
Page 29
M
Auto Exposure Setup
HOW TO USE OSD MENU
AE SETUP - GLOBAL
----------------------- BACKLIGHT OFF
DAY/NIGHT AUTO1
BRIGHTNESS 25
IRIS AUTO
SHUTTER ESC
AGC NORMAL
SSNR MIDDLE
SENS-UP <AUTO>
BACK
EXIT
z Backlight [ON/OFF]
Sets Backlight Compensation
z Day/Night [AUTO1/AUTO2/DAY/NIGHT]
AUTO1 exchanges Day/Night mode faster than
AUTO2.
z Brightness [0~100]
z IRIS [AUTO/MANUAL(0~100)]
Adjusts brightness of images. Iris, Shutter Speed
and Gain are adjusted automatically in
correspondence with this value.
If Iris is set to Auto, Iris should have highest
priority in adjusting AE and Shutter Speed should
be fixed.
4
If Iris is set to Manual, Iris should be fixed and Iris
has lower priority in adjusting AE, in comparison
with others.
z Shutter Speed [ESC/A.Flicker/Manual(×128~1/120000 sec)]
If Iris is set to Manual and Shutter Speed is set to
ESC, Shutter Speed should have highest priority. If
Shutter Speed is set to A.Flicker, to remove
Flicker, Shutter Speed should be set to 1/100 sec.
for NTSC and 1/120 for PAL.
z AGC [OFF/NORMAL/HIGH]
Enhances image brightness automatically in case
that luminance level of image signal is too low.
z SSNR [OFF/LOW/MIDDLE/HIGH]
Enhances images by deducting noises when gain
level of images is too high.
z SENS-UP [AUTO(2~128)/OFF]
Activates Slow Shutter function when luminance of
image (signal) is too dark.
It is possible to set up the maximum number of
frames piled up one on another by Slow Shutter
function.
ini Speed Dome Camera/SM1000 Series
29
Page 30
M
Motion Setup
HOW TO USE OSD MENU4
Setup the general functions of Pan/Tilt motions.
MOTION SETUP
----------------------- MOTION LOCK OFF
PWR UP ACTION ON
AUTO FLIP ON
JOG MAX SPEED 120/SEC
JOG DIRECTION INVERSE
FRZ IN PRESET OFF
<PARKING ACTION SETUP>
<ALARM INPUT SETUP>
BACK
EXIT
z Motion Lock [ON/OFF]
z Power Up Action [ON/OFF]
If Motion Lock is set to ON, it is impossible to
set up and delete Preset, Swing, Pattern and
Group. It is possible only to run those functions.
To set up and delete those functions, enter into
OSD menu.
Refer to “Other Functions" section.
z Auto Flip [ON/OFF]
Refer to “Other Functions" section.
z Jog Max Speed [1°/sec ~360°/sec]
Sets maximum jog speed. Jog speed is
inversely proportional to zoom magnification.
As zoom magnification goes up, pan/tilt speed
goes down.
z Jog Direction [INVERSE/NORMAL]
If you set this to ‘Inverse’, the view in the
screen is moving same direction with jog
tilting. If ‘Normal’ is selected, the view in the
screen is moving reversely.
z Freeze in Preset [ON/OFF]
At start point of preset movement, camera
starts freezing the image of start point. Camera
keeps displaying the image of start point
during preset movement and does not display
the images which camera gets during preset
movement. As soon as camera stops at preset
end point, camera starts displaying live images
which it gets at preset end point.
This function availability should be different by
models.
ini Speed Dome Camera/SM1000 Series
30
Page 31
M
HOW TO USE OSD MENU
Parking Action Setup
4
PARKING ACTION SETUP
----------------------- PARK ENABLE OFF
WAIT TIME 00:10:00
PARK ACTION HOME
BACK
EXIT
Alarm Input Setup
ALARM INPUT SETUP
----------------------- ALARM1 TYPE N.OPEN
ALARM2 TYPE N.OPEN
ALARM3 TYPE N.OPEN
ALARM4 TYPE N.OPEN
ALARM1 ACT NOT USED
ALARM2 ACT NOT USED
ALARM3 ACT NOT USED
ALARM4 ACT NOT USED
BACK
EXIT
If Park Enable is set to ON, camera runs assigned function automatically
if there is no PTZ command during assigned "Wait Time".
z Park Enable [ON/OFF]
z Wait Time [1 minute ~ 4 hour]
The time is displayed with "hh:mm:ss" format
and you can change this by 1 min unit.
z Park Action [HOME/PRESET/PATTERN/SWING/GROUP]
{ HOME
Camera moves to home position if there is no
PTZ command during assigned "Wait Time".
Match the Alarm sensor input to one of Preset positions. If an external
sensor is activated, camera will move to corresponding preset position