CNB SDN-23Z27FW User Manual
www.cnbtec.com
INSTALLATION AND OPERATION MANUAL
XPEED Outdoor Series Ver 1.0
(3810-0250A_110119)
p
panying
XPEED Outdoor Series WWW.CNBTEC.COM
This lightning flash with arrowhead symbol is intended to alert The user to
the presence of un-insulated “dangerous voltage”
Within the product’s enclosure that may be of sufficient magnitude
To constitute a risk of electric shock to
ersons.
~ Important Safety Instructions
Read Instructions
• Read all of the safety and operation instructions before using the product.
Retain Instructions
• Save these instructions for future reference.
Attachments / Accessories
• Do not use attachments or accessories unless recommended by the appliance manufacturer as they may cause hazards, damage product
and void warranty.
Installation
• Do not place or mount this product in or on an unstable or improperly supported location. Improperly installed product may fall, causing
serious injury to a child or adult, and damage to the product. Use only with a mounting device recommended by the manufacturer, or
sold with the product. To insure proper mounting, follow the manufacturer’s instructions and use only mounting accessories
recommended by manufacturer.
Power source
• This product should be operated only from the type of power source indicated on the marking label.
~ Precautions
Operating
• Before using, make sure power supply and others are properly connected.
• While operating, if any abnormal condition or malfunction is observed, stop using the camera immediately and then contact your local
dealer.
Handling
• Do not disassemble or tamper with parts inside the camera.
• do not drop or subject the camera to shock and vibration as this can damage camera.
• Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your quality of camera.
Installation and Storage
• Do not install the camera in areas of extreme temperature, which exceed the allowable range.
• Avoid installing in humid or dusty places.
• Avoid installing in places where radiation is present.
• Avoid installing in places where there are strong magnetic fields and electric signal.
• Avoid installing in places where the camera would be subject to strong vibrations.
This exclamation point symbol is intended to alert the user to
The presence of important operating and maintenance (servicing)
instructions in the literature accom
the appliance.
2
XPEED Outdoor Series WWW.CNBTEC.COM
~ Table of Contents
1. Introduction
Features 4
Product & Accessories 6
Parts Name & Functions 7
2. Installation
Dip Switch Setup 8
Installation Using the Wall Mount 11
Installation Using the Pendant Mount 12
Wire Connections 13
3. Operation
Check Points before Operation 15
Preset and Pattern Function Pre-Check 15
Starting OSD Menu 15
Reserved Preset 15
Preset 16
Swing 16
Pattern 16
Group 17
Other Functions 17
4. OSD Menu
OSD Display of Main Screen 18
General Rules of key Operation for Menu 19
Main Menu 19
Display Setup 19
Privacy Zone Mask Setup ( 26x (S2465N(P)X), 36x (S2965N(P)X) EXview 27x(SCN-22Z27F /SCN-23Z27F) (Option) Models Only ) 20
Camera Setup (27x (SCN-22Z27F /SCN-23Z27F models) 21
Camera Setup (26x (S2465N(P)X), 36x (S2965N(P)X ) EXview Models) 23
Motion Setup 25
Preset Setup 26
Swing Setup 28
Patten Setup 29
Group Setup 30
System Initialize 32
5. Specifications
26x (S2465N(P)X) EXview Models 33
27x (SCN-22Z27F/SCN-23Z27F) Models 34
36x (S2965N(P)X) EXview Models 35
Dimensional Drawings 36
6. System Models and Related Accessories
System Model Numbers 38
Related Accessories 38
3
XPEED Outdoor Series WWW.CNBTEC.COM
1. Introduction
~ Features
Camera Specifications
• Image Pick-up Device: 1/4" Interline Transfer CCD
• Zoom Magnification: 26x Optical Zoom, 12x Digital Zoom (Max. 312x Zoom) → Model S2465N(P)X
27x Optical Zoom, 10x Digital Zoom (Max. 270x Zoom) → Model SCN-22Z27F /SCN-23Z27F
36x Optical Zoom, 12x Digital Zoom (Max. 432x Zoom) → Model S2965N(P)X
• Day & Night Function
• Various Focus Mode : Auto-Focus / Manual Focus / SemiAuto Focus.
• Each Preset has its own video configuration, label, relay output setting values.
You can adjust each Preset setting independently.
Powerful Pan/Tilt Functions
• Max. 360°/sec high speed pan/Tilt Movement
• Using Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path. As a result, time to target view is reduced
dramatically and the video on the monitor is very natural to watch.
• For jog operation using a controller, since ultra slow speed 0.05°/sec can be reached, it is very easy to locate camera to desired target view.
Additionally it is easy to move camera to a desired position with zoom-proportional pan/tilt movement.
Preset, Pattern, Swing, Group, Privacy Mask and More...
• Max. 127 Presets are assignable and characteristics of each preset can be set up independently, such as white Balance, Auto Exposure, Label,
Digital Outputs and so on.
• Max. 8 set of Swing action can be stored. This enables to move camera repetitively between two preset positions with designated speed.
• Max. 4 of patterns can be recorded and played back. This enables to move camera to follow any trajectory operated by joystick as closely as
possible.
• Max. 8 set of Group action can be stored. This enables to move camera repetitively with combination of preset or pattern or Swing. A Group is
composed of Max. 20 entities of Preset/Patten/Swings.
• Privacy Masks are assignable, not to intrude on other’s privacy. (8 Privacy Zones)
→ Only available with Models S2465N(P)X, S2965N(P)X, SCN-22Z27F /SCN-23Z27F (option)
PTZ(Pan/Tilt/Zoom) Control
• With RS-485 communication, Max. 255 of cameras can be controlled at the same time.
• Pelco-D, Pelco-P, Samsung or Panasonic protocol can be selected as a control protocol in the current version of firmware.
4
XPEED Outdoor Series WWW.CNBTEC.COM
OSD(On Screen Display) Menu
• OSD menu is provided to display the status of camera and to configure the functions interactively.
• The information such as Camera ID, Pan/Tilt Angle, Alarm I/O and Preset can be displayed on screen.
Alarm I/O Functions
• 4 alarm sensor inputs and 2 alarm Output relays are available.
• To reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo coupler and the relay is used for alarm output.
• The signal range of sensor input is from DC 5.0 to 12.0 volts to adopt various applications. Meanwhile, the maximum load of relay contact is
250VAC, 3A or 28VDC, 3A.
• If an external sensor is activated, camera con be set to move to the corresponding Preset position. Meanwhile, the output relay can be
matched to some specific preset positions to do counteractions such as turning on the light or sound the alarm.
Reserved Presets for Special Purpose
• Most camera characteristics can be set up easily and directly with reserved preset, not entering into OSD menu. For more information, refer to
“Reserved Preset” in this manual.
Easy Installation and Perfect Outdoor Environment Compatibility
• Fans and heaters are built-in camera for cold and hot temperature environment.
Also idealistic mechanical design protects camera from water and dust. (IP 66)
• It is easy to install and maintain camera with terminal for cable connection in brackets.
5
XPEED Outdoor Series WWW.CNBTEC.COM
1. Introduction
⊙ Product & Accessories
■ Basic Components
■ Other Components (available to be ordered separately)
6
XPEED Outdoor Series WWW.CNBTEC.COM
1. Introduction
⊙ Parts Name & Functions
① Dome Cover Do not detach protection vinyl from dome cover before finishing all installation process to protect dome cover
from scratches or dust.
② DIP Switch
③ Main Body
Cable
④ Drop Prevention
Spring
⑤ Lockup Screw After assembling main body to bracket, screw main body to bracket to protect them from separation by vibration
⑥ Fuse If the fuse is burnt to protect your came from over-current damage, the fuse have to be replace with new one. The
⑦ Cabling
Terminal Block
⑧ Mold Line Mark to assemble main body to bracket.
⑨ TACT Switch
Sets up camera ID and protocol.
Enables signals and power to come and go between main body and mount bracket.
This part keeps the camera from dropping during installation and maintenance. After install the Bracket, please,
hang the spring to the drop prevention hook of main body as shown in picture for further tasks.
and so on.
fuse specification is 250V 2A. however, we recommend consulting with supplier to remove the cause of over-
current.
During installation, Power, Video, Communication, Alarm I/O cables are connected on to this cables terminal block.
Network Board Factory reset
7
XPEED Outdoor Series WWW.CNBTEC.COM
2. Installation
9 Before installing the camera, you should set the DIP switches to configure the camera ID, communication protocol. Do not use the
system upgrade terminal.
~ DIP Switch Setup
■ Camera ID Setup
• ID number of camera is set using binary number.
The example is shown bellow.
Pin 1 2 3 4 5 6 7 8
ID Value 1 2 4 8 16 32 64 128
ex) ID=5 ON OFF ON OFF OFF OFF OFF OFF
Ex) ID=10 OFF ON OFF ON OFF OFF OFF OFF
• The range of ID 1~255. Do not use 0 as camera ID.
• Factory default of Camera ID is 1.
• If you want to control a certain camera, you must match the camera ID with Cam ID setting of
DVR or Controller.
8
XPEED Outdoor Series WWW.CNBTEC.COM
2. Installation
■ Communication Protocol Setup
• Select the appropriate Protocol With DIP switch combination.
Switch state
P0 (Pin 1) P1(Pin 2) P2(Pin 3)
OFF OFF OFF PELCO-D, 2400bps
ON OFF OFF PELCO-D, 9600bps
OFF ON OFF PELCO-P, 4800bps
ON ON OFF PELCO-P, 9600bps
OFF OFF ON SAMSUNG, 4800bps
ON OFF ON PANASONIC, 9600bps
• If you want to control using DVR or P/T controller, their protocol must be identical to camera.
Otherwise, you can not control the camera.
• It you changed camera protocol by changing DIP S/W, the change will be effective after you
reboot the camera.
• Factory default of protocol is “Pelco-D, 2400bps”.
Others Reserved
Protocol/Baud rate
■ Input Sensor Active Type
• When a sensor input is used, its functional type should be set.
There are two types; Normal Open type and Normal Close type.
-Normal Open : Voltage is let out when the sensor is activated
-Normal Close : Voltage is let out when the sensor is not activated
Pin Switch position Sensor type
ST1 (Pin 4)
ST2 (Pin 5)
ST3 (Pin 6)
ST4 (Pin 7)
• If a wrong type of sensor is selected, it activates in the opposite way to the sensor input.
ON Sensor 1 Normal Close
OFF Sensor 1 Normal Open
ON Sensor 2 Normal Close
OFF Sensor 2 Normal Open
ON Sensor 3 Normal Close
OFF Sensor 3 Normal Open
ON Sensor 4 Normal Close
OFF Sensor 4 Normal Open
9
XPEED Outdoor Series WWW.CNBTEC.COM
■ Termination Switch Setting
Termination switch (Pin 4) is used in cases listed below.
• Long-distance communication between the controller and the camera (1-to-1 connection)
When the connection distance between the two units is especially long, communication errors
may occur due to the impedance of transmission cable. In this case, set the termination switch
of both units to ON.
• Controlling multiple cameras (Multiple connection)
The camera may not operate correctly if multiple cameras are connected and controlled. In this
case, set the termination switch of the controller and the last connected camera to ON and the
switch of other cameras is OFF.
Ex) Using the Terminating Resistance.
10
XPEED Outdoor Series WWW.CNBTEC.COM
2. Installation
⊙ Installation Using the Wall Mount
11
XPEED Outdoor Series WWW.CNBTEC.COM
2. Installation
⊙ Installation Using the Pendant Mount
12
Loading...