CNB SD1760PA User Manual

USER INFORMATION:

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION!

Explanation of two Symbols

THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM
OF THE SYSTEM.

"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT
TO RAIN OR MOISTURE"

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance­(servicing) instructions in the literature accompanying the appliance.

PRECAUTION:

!

All the warnings and instructions of this manual should be followed.
Remove the plug from the outlet before cleaning. Do not use liquid

aerosol detergents. Use water damped cloth for cleaning.
To reduce the risk of fire or electric shock, do not expose this appliance

to rain or moisture.
Do not place anything on top of the unit that might spill or fall into it.
Do not attempt to service this unit yourself as opening or removing

covers may you to dangerous voltage or other hazards. Please refer
all servicing to qualified service personnel.

Keep enough space around the unit for ventilation.
Slots and openings on the monitor should not be blocked.

During flashes of lightning or cracks of thunder, or when the system
is not used for a long time, unplug the system power supply to
protect the unit from lightening or power surges.

DIMENSIONS(mm):

Dome (Ø89.5)

SPECIFICATIONS:

Signal System
Scanning System
Scanning Frequency (H)
Scanning Frequency (V)
Image Sensor
Total/Effective Pixels No.
S/N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC / BLC
Input/Output Connector
Audio (Option)
Supplied Voltage
Power Consumption
Dimensions (ØxH
Weight

410K/380K [Normal:270K/250K] 470K/440K[Normal:320K/290K]

Fixed Lens(f=3.8mm, 6.0mm Selectable)/ Pin Hole Lens

1/60~100,000 Sec. 1/50~100,000 Sec.

)

89.5

113.0

NTSC : 525 Lines PAL : 625 Lines

15.734kHz 15.625kHz

550 TV Lines / 480 TV Lines / 380 TV Lines

DC 9V ~ 15V (Recommendation DC 12±0.5V)

2 : 1 Interlace

59.94Hz 50Hz
1/3 inch SONY Super HAD CCD

More than 48dB

1.0 Vp-p (75 Ohms, composite)

Manual

0.3 Lux(High) / 0.1 Lux(Normal)

Power(Red Jack), Video(Yellow Jack)

Internal

Auto
Auto

3 Vp-p (max), 45dB (typ.)

Less than 150mA

89.5 x 63mm
Approx. 157g

ver.0604E

39.024.0

P/N:3810-0083A

CCD CameraColor

ColorDigital DSP

cameracolor

.Fixed

LENS

.Pin Hole

1/3" SONY CCD

INSTALLATION:

This manual explains the installation and operating method for the

color dome camera. Before installation, make sure you are familiar

with this product's special features and proper operating technique.

Stick the guide pattern

1

on the wall or ceiling.

Fixed the camera to a

2

ceiling using two screws.

After fixing it, adjust its

3

pan base and tilt base
properly.

After adjust them, fixed

4

the dome cover.

Ceiling

COMPOSITION:

Guide Pattern

Dome Base

Owner's Manual

CONNECTION:

Mounting
Screw

Dome Cover

NOTE

Insert coin to the side hole and
remove the dome cover by twist coin.

#

1

#

2

Dome Camera

Video

(Yellow)

Power

(

)

Red

Changes in this user manual can
be made without notice, in order
to improve the product quality.

Guide Pattern

Mounting Screw

Video Output

GND

(DC 12V/ Over 0.3A Power Adapter)

No.

Function

#1

Video Output

Power Input

#2

Audio Output White (Option)

※

Power(+)

※

Recommendable

Power Supply

Terminal Color

Yellow

Red

GND

TROUBLESHOOTING:

If you have trouble operating your camera, refer to the following.

If the guidelines do not enable you to solve the problem,

contact an authorized technician.

The image does not
appear on the screen.

The image on the
screen is dim.

The camera does not
work properly, the
surface of the camera
case is hot, and a
black line appears on
the screen.

The screen blinks a lot.

Check the power source for the monitor
and camera and assure that the voltage
and polarity are properly connected and
being supplied correctly.

Check if the lens is stained. If dirty,
clean the lens with a soft, clean cloth.

Adjust the Back Focus of the lens again.

Check if you have connected the camera
to a proper power source and If there is
no problem with the power, turn the unit
off immediately and seek assistance from
our After Service department.

Check if the camera is pointed toward
the sun or a fluorescent lamp.

Adjust the angle or location of the
camera if too much light is coming into
the screen.