CNB NXE3055MR User Manual

XNET Network Weatherproof Camera Installation Manual

XNET Network Weatherproof Camera

(NXE3055MR)

Installation Manual

Ver. 1.2

2 / 23

Network Weatherproof Camera Installation Manual

About this Installation Guide

This product has been tested for compatibility and stability as per high performance standard.
This installation guide covers the installation and operation of Network weatherproof Camera only.
Please read this manual including the important cautions and warnings thoroughly before using the
product even if you are an expert.

Important Notices

The copyright of this manual is owned by Manufacturer.
It is illegal to copy and distribute this manual without permission.
Damages caused by misuse (i.e. use of parts not suggested) will not be covered under warranty.
Contact the store or the manufacturer immediately if there is any problem with the product.
Do not disassemble the product for alteration or repair.
This product complies for CE (Europe) and FCC (USA) regulations for industrial and home electrical
device.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

3 / 23

Network Weatherproof Camera Installation Manual

Index

1. About the product................................................................................................................. 4

1.1. Features of the product .................................................................................................. 4

1.2. Applications .................................................................................................................. 4

2. Product Description ............................................................................................................... 5

2.1. Contents ....................................................................................................................... 5

2.2. Product Information ....................................................................................................... 5

2.3. Hardware Designation .................................................................................................... 6

2.3.1. Switch and Controls ............................................................................................ 6

2.3.2. Internal configuration ......................................................................................... 7

2.3.3. Connecting to Cables .......................................................................................... 8

2.3.4. Alarm Device Connection .................................................................................. 10

2.3.5. Mounting the Camera ....................................................................................... 11

3. Software Installation............................................................................................................13

3.1. Installing system ..........................................................................................................13

3.2. IP-Installer and IP address Configuration ........................................................................18

3.2.1. About IP-Installer ............................................................................................. 18

3.2.2. IP Address Configuration ................................................................................... 18

4. Using Web Viewer ...............................................................................................................20

4.1. Logging In ...................................................................................................................20

4.2. Web Viewer Page ..........................................................................................................21

5. Specification .......................................................................................................................22

4 / 23

Network Weatherproof Camera Installation Manual

1. About the product

This Product is an internet based security and surveillance system that is compatible with various networks

with its easy installation, various user interfaces, and multi-functional compressor Codec such as H.264 and

MJPEG. The product provides reliable real-time surveillance by SXGA real time video/ audio, event-based local

storage, and hybrid IP technology that can be used with the existing analog CCTV systems.

11..11.. FFeeaattuurreess ooff tthhee pprroodduucctt

Advanced Video/ Audio compression technology (MJPEG/H.264, G.711)

 Progressive technology - Sharp and clear image with no ghost effect.

 Hybrid IP Technology - Analog CCTV video output for connecting to an existing analog system.

 Multi-Codec stream - Live video signal compression to MJPEG or H.264 for various applications.

 2-way Audio - Bi-directional voice communication between Client’s PC and camera.

 Smart Event feature - Motion detection, Alarm sensor/output, pre- and post- alarm for automated

surveillance with no need for an attendant or monitoring.

 Installation Wizard - Easy and unified installation for large network.

 Motion Detection with three different areas - Alarm output and Video/ Audio data transmission to FTP site

or e-mail.

 Supports Various resolutions

-

1080P(1920X1080),SXGA(1280X1024),SXGA(1280X960),720P(1280X720),XGA(1024X768),D1(720X480),

VGA(640x480),CIF(352x240),QVGA(320X240),

 Remote firmware upgrade over the network

11..22.. AApppplliiccaattiioonnss

 Surveillance (Surveillance areas can be a building, store, factory, parking lot, financial institutions,

government buildings, military facilities, etc.)

 Remote video monitoring (Monitoring areas can be a hospital, kindergarten, traffic monitoring, remote

branch office, weather, environment preservation, illegal disposal of trash, etc.)

 Real time broadcasting over the internet (Broadcasting can be from a resort facility, parties, festivals,

remote business meetings, educational trainings, etc.)

5 / 23

Network Weatherproof Camera Installation Manual

Contents

Description

Additional info.

Product

NXE3055MR

POWER ADAPTOR

AC Power Cable

INPUT : 100~240VAC 50-60Hz
OUTPUT : 12VDC 2A / AC24V 2.5A
2 Jack Power Cable for Outlet

BRACKET, SUNVISOR

BRACKET BASE:1EA
SUNVISOR : 1EA

CD

Software and User’s manual

DC Plug

AC/DC CONNECTOR

CVBS Cable

A Plug for DC Power Adaptor
Two Position Connector for Power
Input
BNC connector for Analog Video
Output

Accessory

L-WRENCH : 2EA
SCREW 4EA
Wall Anchors 4EA
Sunvisor Screws : 1EA
Nut : 4EA

NXE3055MR

Install CD

IP-Installer

Viewer Program

(CMS)

IP Weatherproof Camera

(NXE3055MR)

A software for detecting the camera
in the network and assigning an IP
address

A software to monitor/record live Video
and audio from the camera

2. Product Description

22..11.. CCoonntteennttss

Please make sure the following contents are included in the package.

22..22.. PPrroodduucctt IInnffoorrmmaattiioonn

6 / 23

Network Weatherproof Camera Installation Manual

22..33.. HHaarrddwwaarree DDeessiiggnnaattiioonn

22..33..11.. SSwwiittcchh aanndd CCoonnttrroollss

1. Motorize Lens : 3-9mm Motorize Lens

2. IR LED : IR Led light controlled by CDS Sensor.

3. CDS Sensor : senses the light intensity (low light level).

4. Casing Screws (front - 4EA) : attach the front and rear bodies together

5. Sunvisor : Shields off the direct sunlight to avoid overheating the camera module

6. Sunvisor Screws : fix the Sunvisor on the main body

7. Rotate adjusting Bolt: fixes the adjustment of the camera’s rotational angle.

8. Tilt adjusting Bolt: fixes the adjustment of the camera’s tilt angle.

9. Pan adjusting Bolt: fixes the adjustment of the camera’s pan angle.

10. FRONT BODY

11. Connecting Terminal: Please refer to 2.3.2. Connecting Terminal

12. REAR-BODY

7 / 23

Network Weatherproof Camera Installation Manual

22..33..22.. IInntteerrnnaall ccoonnffiigguurraattiioonn

1. Micro SD Card Slot :

Video images can be stored into a Micro SD card when an event occurs. Please use less than 16 GB

MICRO SD Memory.

Figure 2-3. MICRO SD CARD

2. Video Out: Analog Video output. When installing the camera, use this output to connect a CCTV

monitor to quickly check for desired image. The enclosed CVBS cable has an RCA termination.

(Enable Video Out in Camera’s menu to activate this Analog video output. The analog Video can only

be used in resolutions lower than VGA.)

3. Factory Reset Button : When the Camera is powered up, press and hold this button for 3 seconds

to reset the camera to factory default state

4. Autofocus Button : Adjust automatically the focus of the camera.

5. LINK LED: Yellow light indicates that the network is properly connected.

6. ACT LED: Green light indicates that the camera is connected to 100Mbps LAN. Also, the blinking

green light indicates that the system is receiving data.

7. PWR LED: Red light indicates that 12V DC/24V AC power is connected.