CNB NDE5055MF User Manual

XNET Network Dome Camera Installation Manual

XNET Network Dome Camera

(NDE5055MF)

Installation Manual

Ver. 1.2

XNET Network Dome Camera Installation Manual

About this Manual

A compatibility and durability test ensured this product’s high performance.

This manual is for XNET IP Dome Camera users only, and it describes operations related to XNET IP
Dome Camera.

Please read this manual thoroughly paying attention to cautions and warnings before using the product
even if you have used similar products before.

Important Notices

The copyright of this manual is owned by CNB Technology Inc.
It is illegal to copy and distribute this manual without permission.
Damages caused by use of parts not recommended and by misuse will not be applicable for support.
Contact the store or the manufacturer immediately if (you think) there is any problem with the
product.
Contact the store or the manufacturer before disassembling the product for alteration or repair.
XNET is a trademark of CNB Technology Inc.
This product complies for CE (Europe) and FCC (USA) regulations for industrial/home use electrical
device.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

2 / 22

XNET Network Dome Camera Installation Manual

Index

1. About XNET ...................................................................................................................... 4

1.1. About XNET .......................................................................................................................... 4

1.2. Features of XNET .................................................................................................................. 4

1.3. Applications ........................................................................................................................... 4

2. About the Product ........................................................................................................... 5

2.1. Contents ................................................................................................................................ 5

2.2. Product Information ............................................................................................................... 5

2.3. Hardware Designation ........................................................................................................... 6

2.3.1. Switch and Controls .................................................................................................................... 6

2.3.2 Connecting Cables ....................................................................................................................... 7

2.3.3 Connecting to Alarm Devices ....................................................................................................... 9

3. Software Installation ...................................................................................................... 10

3.1. Installing XNET .................................................................................................................... 10

3.1.1. Installation ................................................................................................................................. 10

3.1.2. Cable Connection ...................................................................................................................... 11

3.2. Installing IP-Installer Software and Configuring IP address .................................................. 16

3.2.1. About IP-Installer ....................................................................................................................... 16

3.2.2. Configuring IP Address .............................................................................................................. 16

4. Using Web Viewer .......................................................................................................... 18

4.1. Logging In ........................................................................................................................... 18

4.2. Web Viewer Page ................................................................................................................ 19

5. Specification .................................................................................................................. 21

3 / 22

XNET Network Dome Camera Installation Manual

1. About XNET

11..11.. AAbboouutt XXNNEETT

XNET is an internet based security and surveillance system that is compatible with various network conditions

through easy installation and user interface as well as multi-functional compressor Codec such as H.264,

MJPEG. XNET provides stable real-time surveillance by real time video/ audio at 1080p level, local storage for

any network problems, and hybrid IP technology that can be used with existing analog CCTV devices.

11..22.. FFeeaattuurreess ooff XXNNEETT

Most advanced Video compression technology (H.264/MJPEG)

Progressive technology - Progressive scan makes the image sharp and clear without ghost effect.

Hybrid IP Technology - CCTV analog video output can be used for existing analog CCTV devices.

Transmission of Multi-Codec stream - Live video signal can be compressed to H.264 or MJPEG and sent to

meet various applications of network or user.

2-way Audio Communication (Bi-directional voice communication between Client’s PC and XNET)

Smart Event feature - On the top of motion detection and sensor/alarm feature, pre- and post- alarm

feature allows automated surveillance without an attendant’s monitoring.

Install/ Operation Wizard - Install/ Operation Wizard not only makes it easy for installers and users, but

also offers a unified installation setup for massive scale installations.

Up to 3 motion detection areas

and Video data transmission to FTP site or e-mail upon detecting a motion.

Supports Various resolutions

-

1080P(1920X1080), SXGA(1280X1024), SXGA(1280X960), 720p(1280X720), XGA(1024X768), D1(720X480),

VGA(640x480), CIF(352x240), QVGA(320X240)

Remote Control over the network for software upgrade

11..33.. AApppplliiccaattiioonnss

 Surveillance (Building, store, factory, parking lot, financial institutions, government buildings, military

facilities, etc.)

 Remote video monitoring (Hospital, kindergarten, traffic monitoring, remote branch office, weather,

environment preservation, and illegal disposal of trash, etc.)

 Real time broadcasting over the internet (Resort facility, parties, festivals, etc), remote business meetings,

and educational trainings, etc.

4 / 22

XNET Network Dome Camera Installation Manual

Contents

Description

Additional info.

XNET

XNET IP Dome Camera

POWER ADAPTOR

AC Power Cable

INPUT : 100~240VAC 50-60Hz
OUTPUT : 12VDC 2A

GUIDE PATTERN

Guide Pattern

CD

Software and User’s manual

DC JACK

DC CONNECTOR

CVBS JACK

Connect the Power Adaptor DC jack
Connect the DC jack Connector

CVBS JACK

Accessory

SCREW 3EA, Wall Anchors 3EA

XNET

(NDE5055MF)

Install CD

IP-Installer

Viewer Program

(CNB-CMS)

IP Dome Camera

(NDE5055MF)

A software that assigns an IP address
to the product

A software that monitors and records
Audio and Video signal from the device

2. About the Product

22..11.. CCoonntteennttss

Please make sure the following contents are included when you open the package.

22..22.. PPrroodduucctt IInnffoorrmmaattiioonn

5 / 22

XNET Network Dome Camera Installation Manual

Analog Video
Output

EVENT LED

EVENT Alarm Out
Signal is turned on.

SYSTEM LED
The camera at the end of boot

PWR LED

Power is connected indicates

SD CARD SLOT

For Mounting the SD
Card Slot.

Factory Reset button

Recalls factory default
configurations

ACT, LINK LED

Network status LED

EASY-SWITCH(Auto Focus)
Adjust automatically
the focus of the camera

Mega Pixel

Motorize Lens

22..33.. HHaarrddwwaarree DDeessiiggnnaattiioonn

22..33..11.. SSwwiittcchh aanndd CCoonnttrroollss

This shows Camera module inside the dome cover.

 STATUS LED

 PWR LED : Red light indicates that 12V DC power is connected.

 EVENT LED : Green light indicates that Alarm Out signal is turned on.
 SYSTEM LED : The system operates normally when the Green LED blinks

 LINK LED : Red light indicates that the network is properly connected.
 ACT LED : Green light indicates that the XNET system connected to 100Mbps LAN. This green lamp

will blink If the system receives data.

6 / 22

XNET Network Dome Camera Installation Manual

NETWORK

ALARM IN/OUT

Audio OUTPUT

Audio INPUT

POWER

CVBS OUT

22..33..22 CCoonnnneeccttiinngg CCaabblleess

 INPUT, OUTPUT

 Power Input

Use the cable adapter(DC12V JACK) in the package to connect power.

Please use the accessory power supply provided in the package.

Except when connected to AC24V DC jack please use(DC12V/2A)

 Analog Video Output

Use this output for immediate monitoring of the video during installation.

Use the supplied cable adapter

(Yellow for video and White for Video Ground GND)

This adapter can be connected to a cable through a BNC terminal Output connector.

(Select Video Out at menu screen to enable this output)

Audio Connection

MIC/Line Input (Mono)

Connects to auxiliary Audio device or microphone.

Line Output (Mono)

Audio signal output to a Power Amplified device or Speaker. This can be used to listen to the audio

signal sent from a remote PC for Bi-directional Audio communication.

 Alarm Connection

These wires connect to Alarm input/output devices.

 Alarm Sensor Input: Connect to Alarm sensor devices such as IR Sensor or Heat sensor. These can

be configured to normally close or normally open operation.

 Alarm Output: Connect to Alarm devices such as Relay operated Siren Lamp or Alarm Light.

These can be configured to normally close or normally open operation.

 Please refer to “2.3.3 Connection to Alarm Devices” for detailed instruction on how to connect

sensors and Relays.

7 / 22