Clinton Electronics ce-x109 Instruction Manual

High Resolution Built-in Lens Color Camera

INFORMATION - This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

◆

Do NOT use power sources other than those specified.

◆

Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and

should conform to all local codes.

The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING - Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.

CAUTION : To prevent electric shock and risk of fire hazards:

High Resolution Built-in Lens Color Camera

■

Contents

Camera Operation

■ Settings

■ EXIT

ㆍ LENS

ㆍ SHUTTER

ㆍ WHITE BALANCE

ㆍ󰼿BLC (Back Light Compensation)

ㆍ AGC (Auto Gain Control)

ㆍ ADJUST

ㆍ FUNCTION

󰼿󰼿󰼿- CAMERA ID

󰼿󰼿󰼿- DAY & NIGHT

󰼿󰼿󰼿- MIRROR

󰼿󰼿󰼿- MOTION DETECTION

󰼿󰼿󰼿- PRIVACY

󰼿󰼿󰼿- GAMMA

󰼿󰼿󰼿- LANGUAGE

󰼿󰼿󰼿- RESET

󰼿󰼿󰼿- RETURN

Specifications

Troubleshooting

Features

Warnings and Precautions

Names and Functions of Parts

■

Front

■

Top

■

Rear

Installation

■

Connecting to a monitor

■

Connecting to power

High Resolution Built-in Lens Color Camera

■

Features

Warning ■

The camera requires periodic inspection.

Contact an authorised technician to carry out the inspection.

Stop using your camera when you find it malfunctioning.

If the camera emits smoke or is unusually hot for a long period, a fire may be caused.

Do not Install the camera on a surface that can not support it.

If the camera is installed on an inappropriate surface, it may fall and cause injury.

Do not hold plug with wet hands.

It could cause an electric shock.

Do not dis-assemble the camera.

It may result in an electric shock or other hazards.

Do not use the camera close to a gas or oil leak.

It may result in a fire or other hazards.

Horizontal Resolution of 540 TV Lines

Clear image quality has been achieved by employing a SONY CCD with 410,000 (effective) pixels, which provides a horizontal resolution of 540 TV lines.

PRIVACY Function

The PRIVACY function conceals the areas not required to appear on the image.

High Sensitivity

The built-in high sensitivity SONY COLOR CCD enables a clear image even at 0.15Lux

Programmable GAMMA Processing

Controlled by OSD Menu

The camera functions are controlled by selecting text displayed on the monitor screen.

Additional Functions

MOTION DETECTION, MIRROR, SHARPNESS and COLOR ADJUST functions are also available.

Electronic IRIS

The electronic IRIS function enables continuous automatic control of the shutter between 1/50(1/60)~1/100,000 seconds.

Auto Iris Vari-focal Built-in Lens

DC Auto Iris Vari-focal Lens is built in.

Fashionable Design

The most modernized and simple design of the camera will go well with the place inquiring good appearance.

DAY & NIGHT

This camera has a function that automatically selects the mode that is appropriate for daytime or night-time conditions. The COLOR mode operates in daytime conditions to provide optimum colors, and BW mode operates in nighttime conditions to enhance the definition of the image.

DNR (Digital Noise Reduction)

The amount of low illuminance noise has been significantly reduced, and the signal-to-noise ratio (S/N ratio) as well as horizontal resolution have been improved, resulting in a clear and sharp image display even in the dark.

High Resolution Built-in Lens Color Camera

■

Precautions

Do not install the camera in extreme temperature conditions.

Do not install the camera under unstable lighting conditions.

Do not touch the front lens of the camera.

Only use the camera under conditions where temperatures are between

-10˚C and +50˚C. Be especially careful to provide ventilation when operating under high temperatures.

It can cause the image quality to be poor.

Severe lighting change or flicker can cause the camera to work improperly.

This is one of the most important parts of the camera. Be careful not to leave fingerprints on the lens cover.

Do not install or use the camera in an environment where the humidity is high.

ㆍIf the camera is exposed to spotlight or an object reflecting strong light,

smear or blooming may occur.

ㆍPlease check the power supply satisfies the normal specification before

connecting the camera.

It can cause malfunctions to occur.

If it gets wet, wipe it dry immediately. Liquids can contain minerals that corrode the electronic components.

If exposed to radioactivity the CCD will fail.

It can damage the CCD.

Do not drop the camera and protect it from physical shocks.

Do not expose the camera to rain or spill beverage on it.

Do not expose the camera to radioactivity.

Never keep the camera pointed directly at strong light.

High Resolution Built-in Lens Color Camera

Front

■

Components

Names and Functions of Parts ■

Top

①

Built-in Lens

Built-in DC Auto Iris Vari-focal lens.

②

Front Cover

Used to access focus or zoom handle. After adjusting, be sure to close it.

③

Focus Handle

Used to provide accurate focusing of object within lens field of view.

④

Zoom Handle

Used to adjust zoom magnification of lens.

⑤

Tripod Mount Bracket Screw Hole

Used to fix the tripod mounting bracket on the top of the camera

⑥

Mounting bracket screw hole

Please use the screw hole when fixing the camera onto the mounting bracket. Please use the clamp screw as specified picture.

※

The mounting bracket can be separated and attached to the top of the camera. In this instance please do not tighten the screw to a depth of more than 5mm, otherwise serious damage can occur to the inside of the camera.

High Resolution Built-in Lens Color Camera

■

Camera Operation

■

SETUP menu

LENS (selection)

SHUTTER (

condition and speed control)

WHITE BALANCE control

BLC

(Back Light Compensation)

AGC (Auto Gain control)

ADJUST

FUNTION

EXIT

ㆍMANUAL ㆍDC

ㆍFIXED ㆍAUTO ㆍFLK

ㆍATW ㆍMANUAL

ㆍAWB ㆍFIXED

ㆍBLC AREA ㆍBLC RATIO

ㆍAGC CONTROL

ㆍCONTRAST ㆍCAMERA ID

ㆍCR - GAINㆍCB - GAIN

ㆍRETURN ㆍCAMERA ID ㆍDAY / NIGHT ㆍMIRROR

ㆍMOTION ㆍPRIVACY ㆍGAMMA ㆍLANGUAGE ㆍRESET

Settings can be made using the 5 buttons located in the camera.

1. Press the SET button

ㆍSettings can now be made. The SETUP menu is displayed on the monitor.

2. Select a menu item from the list available by using the UP and DOWN buttons.

ㆍ

Funtions are selected using up and down buttons.

ㆍ

The selected position is displayed in blue.

■

Settings

SETUP

LENS DC

SHUTTER FIXED

WHITE BAL. ATW

BLC OFF

AGC ON

ADJUST

FUNCTION

EXIT

AC 24V IN DC 12V IN

VIDEO OUT

POWER

UP button

SETUP button

RIGHT button

DOWN button

LEFT button

SET

Note

SETUP

LENS DC

SHUTTER FIXED

WHITE BAL. ATW

BLC OFF

■

Camera Operation

3. Press the LEFT or RIGHT button to change modes.

ㆍWhen the LEFT or RIGHT button is pressed, available values and modes are displayed in order. Keep pressing the button until you get to the mode you wish to select.

4. Select 'EXIT' and then press the SET button to exit the set up menu.

This function is used to adjust the brightness of the screen.

1. When the SETUP menu is displayed on the screen, position the cursor to point to 'LENS' by using the UP and DOWN buttons.

2. Select the type of the lens setting to use by pressing the LEFT or RIGHT button.

LENS (selection)

ㆍIf appears at the mode selected, it means that there is a sub-menu

which can be selected by pressing the SET button.

● DC

: Auto Iris Lens selection

● MANUAL : Manual Lens selection

3. Press the SET button to return to the previous menu.

Note

ㆍThe brightness of the screen can be adjusted in DC mode. The

brightness can be adjusted within the range of 0 ~255. The optimum level of brightness can be achieved using this adjustment.

SETUP

LENS DC

SHUTTER FIXED

WHITE BAL. ATW

BLC OFF

AGC ON

ADJUST

FUNCTION

EXIT

Modes can be changed using the LEFT and RIGHT buttons.

Select the desired

menu item by

using the UP and

DOWN buttons.

LENS DC

: RETURN

BRIGHTNESS 093

High Resolution Built-in Lens Color Camera

SETUP

LENS MANUAL

SHUTTER FIXED

WHITE BAL. ATW

BLC OFF

■

Camera Operation

Auto or manual control can be selected.

1. When the SETUP menu is on the screen, position the cursor to point to 'SHUTTER' by using the UP and DOWN buttons.

2. Select the shutter mode by pressing the LEFT or RIGHT button.

● FLK : Select 'FLK' mode when flickering occurs on the screen

due to an imbalance between illumination and frequency. NTSC Model:1/100, PAL Model: 1/120

● AUTO : Automatic control of the shutter speed is enabled.

When AUTO mode is on, the shutter speed is controlled automatically according to the brightness of the scene.

● FIXED : The shutter speed can be controlled manually.

● MANUAL mode (256 steps) :

There are 256 pre-defined electronic shutter speeds in manual mode available for selection; set according to environment conditions.

3. Select 'FIXED' mode for manual shutter speed adjustment.

ㆍ

Selectable speeds are from '1/60' to '1/120,000'sec (NTSC) and '1/50'

to '1/120,000'sec (PAL).

4. Press the SET button when the settings are completed.

SHUTTER (condition and speed control)

The screen colors can be adjusted using the WHITE BALANCE function.

Position the cursor to point to 'WHITE BAL' on the SETUP menu by using the

UP and DOWN buttons.

2. Select the mode you wish to adjust by pressing the LEFT or RIGHT buttons.

WHITE BALANCE

※Select one of the 4 modes below.

●

ATW

(Auto Tracking White Balance) : This mode can be used within the

color temperature range 1,800˚K ~ 10,500˚K (eg, fluorescent light, outdoor, sodium vapour lamp etc.)

●

AWB(Automatic White Balance)

: Press the SET button while the camera is directed at a piece of white paper to obtain the optimum state under current illumination. If the environment, including the light source, changes the white balance will need to be adjusted again.

●

MANUAL : The manual adjustment mode enables finer adjustment.

Select ATW or AWB first then change to manual adjustment mode and press the SET button. Set the appropriate color temperature then increase / decrease the red and blue color values and monitor the color changes of the object.

●

AWB FIXED optimized at 2100˚K

MODE1 : 2680˚K (No light source) MODE2 : 3200˚K MODE3 : 5500˚K (Fluorescent light source) MODE4 : 5100˚K

SETUP

LENS MANUAL

SHUTTER AUTO

WHITE BAL. ATW

BLC OFF

AGC ON

ADJUST

FUNCTION

EXIT

SETUP

LENS MANUAL

SHUTTER FLK

WHITE BAL. ATW

BLC ON

AGC ON

ADJUST

■

Camera Operation

ㆍUnder the following conditions the WHITE BALANCE function may not operate

properly. In such cases, please select the AWB mode.

①

When the object's surroundings have a very high color temperature (eg, a clear sky and sunset)

②

When the object's surroundings are dark

③

If the camera directly faces a fluorescent light or is installed in a place where there are considerable changes in illumination, the WHITE BALANCE function may become unstable.

Note

1. Position the cursor to point to 'AGC' on the SETUP menu by using the UP and DOWN buttons.

2. Select the value required by pressing the LEFT or RIGHT button. As the level of gain increases the screen gets brighter but the level of noise will also increase. (256 steps)

AGC (Auto Gain Control)

When there is a strong backlight behind the object, clear images of the background as well as the object can still be obtained by using the BACKLIGHT function.

1. Position the cursor to point to 'BLC' on the SETUP menu by using the UP and DOWN buttons.

2. Select the value required by pressing the LEFT or RIGHT button.

Press the SET button to enter the BLC AREA and BLC RATIO menus.

4. The BLC Area contains a grid of 64 squares where BLC can be applied.

5. The BLC RATIO can now be adjusted (64 steps); a higher value leads to a clearer image.

BLC (Back Light Compensation)

SETUP

LENS MANUAL

SHUTTER FLK

WHITE BAL. ATW

BLC OFF

AGC ON

ADJUST

FUNCTION

EXIT

BLC AREA

ALL SET RETURN EXIT

BLC SETUP

RETURN

BLC RATIO

BLC AREA

BACKLIGHT ON BACKLIGHT OFF

High Resolution Built-in Lens Color Camera

■

Camera Operation

● Contrast : The image contrast can be adjusted using the left and right

buttons. (256 steps)

● Sharpness : The sharpness of the image can be adjusted using the left

and right buttons. (32 steps)

● CB-Gain : The blue color can be increased/decreased using the left

and right buttons. (256 steps)

● CR-Gain : The red color can be increased/decreased using the left

and right buttons. (256 steps)

ADJUST FUNCTION

Position the cursor to point to 'FUNCTION' on the SETUP menu by using

the UP and DOWN buttons.

2. Select the mode required by pressing the LEFT and RIGHT button.

●

CAMERA ID : If an ID is input, this camera ID appears on the monitor and recorded footage.

1) Position the cursor to point to 'CAMERA ID' by using the UP or DOWN button.

2) Select 'ON' by pressing the LEFT or RIGHT button.

ㆍ

If 'OFF' is selected, the ID does not appear on the monitor even if it has been input.

Note

SETUP

LENS MANUAL

SHUTTER AUTO

WHITE BAL. ATW

BLC ON

AGC ON

ADJUST

FUNCTION

EXIT

FUNCTION

RETURN

DAY NIGHT

OFF

RESET

LANGUAGE

MOTION

OFF 0 . 45 ENGLISH

MIRROR

OFF

CAMERA ID

COLOR

PRIVACY GAMMA

DAJUST

RETURN

CONTRAST 083

SHARPNESS 16

CB_GAIN 193

CR_GAIN 253

FUNCTION

RETURN

DAY NIGHT

OFF

RESET

LANGUAGE

MOTION

OFF 0 . 45 ENGLISH

MIRROR

OFF

CAMERA ID

COLOR

PRIVACY GAMMA

High Resolution Built-in Lens Color Camera

■

Camera Operation

ㆍIf the wrong name has been input.....

Press the SET button after moving the cursor to CLR and all the letters will be erased. If you want to correct a letter move the cursor to the arrow at the bottom left of the screen and press 'SET'. Position the cursor above the letter you wish to correct and then move the cursor onto the letter you wish to choose and press the SET button.

Note

3) Press the SET button.

4) Up to 15 characters can be used for the camera ID.

5) User can select a position to display the camera ID.

ㆍ Move the cursor to a Position and choose a character by using the

UP and DOWN button.

ㆍ Select from the alphabet, numbers(0~9) or 27 special symbols.

ㆍ Repeat the above steps until the ID is complete.

ㆍ

Move the cursor to ' ' symbol and press SET to finish the ID process.

ㆍ Lock in the characters by using the SET button at ' ' position.

ㆍ

Move the cursor to ' C ' letter and press SET to delete the selected letter.

● DAY & NIGHT

AUTO :

This camera has a function which automatically changes to the appropriate mode dependant on lighting levels. COLOR mode is selected during daylight and B/W mode at night time.

- COLOR : The color mode is selected as the default, and the camera does not change automatically.

- B/W : Discards the color information and displays in black and white.

ㆍWhen the AGC is turned off, COLOR does not operate.

Note

●

MIRROR

- ON : Sets a horizontal image inversion.

- OFF : Cancels the inversion.

ID SETUP

RETURN

POSITION

CAMERA ID CT

●

MOTION DETECTION

Users can set the motion detection area just like BLC area setting. The screen is divided in to 64 squares. Selected areas are brighter than non-selected areas. The cursor turns red within selected areas, whilst it turns yellow in non-selected areas. To escape from the area selection press the 'SET' button for 3 seconds and select 'EXIT' to return to the main menu. Users can select all areas using 'ALL SET' and can deselect all areas using 'ALL CLEAR'.

MOTION

RETURN

MOTION TH.

AREA

037

MOTION TRACE. OFF

MIRROR ON

MIRROR OFF

High Resolution Built-in Lens Color Camera

■

Camera Operation

●

PRIVACY

Users can set up to 4 areas as privacy zones. 'AREA STATE' allows users to turn the privacy mode on or off within each designated area. The value of 'LEFT' cannot be greater than the value of 'RIGHT'. The value of 'TOP' cannot be greater than the value of 'BOTTOM'. 'COLOR' setting is applied to all 4 privacy areas.

●

LANGUAGE

Users can select their preferred language for the OSD menu from either, English, Korean, Chinese (Big5), Chinese (Simplified) or Japanese.

●

GAMMA

Users can change the gamma settting in 0.5 steps, between 0 and 1.0 (20 steps).

●

RESET :

Returns to factory settings.

●

RETURN :

Saves the FUNCTION menu and returns to the SETUP menu.

Saves all the setting menus and then exits.

EXIT

FUNCTION

RETURN

OFF

DAY NIGHT

OFF

RESET

LANGUAGE

MOTION

OFF 0 . 45 ENGLISH

MIRROR

OFF

CAMERA ID

COLOR

PRIVACY GAMMA

FUNCTION

RETURN

OFF

DAY NIGHT

OFF

RESET

LANGUAGE

MOTION

OFF 0 . 45 ENGLISH

MIRROR

OFF

CAMERA ID

COLOR

PRIVACY GAMMA

PRIVACY

AREA SEL AREA 0

RETURN

AREA STATE

LEFT

137

185

RIGHT

TOP

029

BOTTOM

084

COLOR

008

■

Troubleshooting

If there are problems with the camera operation, check the tables below. If the problem persists, please contact the agent who supplied the product.

Problems

Nothing appears on the screen.

The video image is not clear.

The screen is dark.

There is a problem with the camera operation. The camera surface is too hot and black stripes appear on the screen.

ㆍCheck the power connection.

ㆍCheck the video signal line connection.

ㆍMake sure that the lens is clean.

Clean the lens with a clean lint free cloth or brush.

ㆍAdjust the contrast control on the monitor. ㆍMake sure that the screen is not exposed

directly to a bright light. Re-position the camera if necessary.

ㆍAdjust the contrast control of the monitor. ㆍIf there is an intermediate device, set the75ohm

Hi-z correctly, and also check the connections.

ㆍIf necessary, adjust the brightness level..

ㆍCheck if an appropriate power source to

the camera complies with the manufacturer's standard requirement, or if the voltage is fluctuating. Check for ground loops.

Troubleshooting

Problems

The MOTION DETECTION function is not working.

Colors are not quite right.

The screen is flickering.

COLOR mode is not working.

ㆍCheck if 'MOTION DETECTION' mode is turned on.

ㆍCheck the setting of the MD AREA.

ㆍCheck the 'WHITE BAL' setting.

(Please refer to page 16)

ㆍCheck if the camera is facing directly into sunlight or fluorescent light.

ㆍCheck if the AGC menu is set to the OFF position.

Troubleshooting

High Resolution Built-in Lens Color Camera

■

Specifications

ITEM

Power Source

Total Pixels

Effective Pixels

Size

Scanning System

Synchronisation Frequency

Resolution

Video Output

S/N (Y signal)

Min. Illumination

Color

White Balance

Electronic Shutter Speed

O.S.D

Motion Detection

BLC

Mirror

Privacy Function

C C D

sync

E L E C T R I C A L

AC24V / DC12V DC12V AC24V / DC12V DC12V

130mA(AC24V)/180mA(DC12V)

130mA

130mA(AC24V)/180mA(DC12V)

130mA

811(H) x 508(V) 795(H) x 596(V)

768(H) x 494(V) 752(H) x 582(V)

SONY 1/3" Super HAD High Sensitivity Color CCD

2:1 Interlace

INT

Horizontal:15.734 KHz Vertical :59.94 Hz Horizontal: 15.625 KHz Vertical : 50.00 Hz

More than 540 TV Lines

1.0Vp-p/75(Video 0.714Vp-p Sync 0.286Vp-p) 1.0Vp-p/75 (Video 0.7 Vp-p Sync 0.3 Vp-p

)

50dB (AGC Off)

0.15Lux 40 IRE (F1.2)

COLOR / AUTO / BW

ATW / AWB / FIXED / MANUAL(1,800˚K~10,500˚K)

AUTO / MANUAL(1/60~1/100,000) AUTO / MANUAL(1/50~1/100,000)

Built-in

ON / OFF (64 Programmable Zones)

Built-in (Horizontal Image Inversion)

ON / OFF (4 Programmable Zones)

-10˚C ~ +50˚C / 30~90% RH

380g

NTSC PAL

Operating Temperature/Humidity

Weight

Clinton Electronics ce-x109 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual