Clinton Electronics CE-CP12B User Manual

CLINTON Electronics 6701 Clinton Road Loves Park, IL 61111
1.800.447.3306 Sales
1.800.549.6393 Support
1.800.633.8712 Fax
www.clintonelectronics.com
Hold lower pole section and turn counter-clockwise to loosen
Prevent lower pole from falling by holding lower pole section here
Secure assembly by turning collar clockwise: hand tighten as snug as possible
Prevent lower pole from falling by holding lower pole section here
Thread the conduit set-screw through the hole on the end of the lower pole.
Conduit set-screw
1/4”-20 Lock Nut
1/4” Washer
1/4” Washer
3/4” Conduit Set-Screw Connector (included with Clinton Electronics pendant mount)
1/4”-20 socket head allen bolt
1/4” Washer
7
/
16
3/8”-16 Lock Nut
Fender Washer
Truss or Channel Strut
1/4”-20 Lock Nut
1/4”-20 socket head allen bolt
1/4” Washer
1/4” Washer
Min. Hole Size: 3/8” Max. Hole Size: 5/8”
400mm Long Safety Cable
1/4”-20 Safety Cable Lock Nut
7/16” Wrench
Secure assembly by turning collar clockwise: hand tighten as snug as possible
Prevent lower pole from falling by holding lower pole section here
Thread the conduit set-screw through the hole on the end of the lower pole.
Conduit set-screw
3/4” Conduit Set-Screw Connector (included with Clinton Electronics pendant mount)
Hold lower pole section and turn counter-clockwise to loosen
Prevent lower pole from falling by holding lower pole section here
Secure assembly by turning collar clockwise: hand tighten as snug as possible
7/16”
If drilling is necessary,
Use 7/16” metal drill
bit to drill through steel
mounting surface.
Prevent lower pole from falling by holding lower pole section here
Thread the conduit set-screw through the hole on the end of the lower pole.
Conduit set-screw
1/4”-20 Lock Nut
1/4”-20 socket head allen bolt
1/4” Washer
1/4” Washer
3/4” Conduit Set-Screw Connector (included with Clinton Electronics pendant mount)
7/16”
If drilling is necessary, Use 7/16” metal drill bit to drill through steel mounting surface.
7
/
16
10
1/4”-20 socket head allen bolt
1/4” Washer
3/16” Allen Wrench
7/16” Wrench
Hold lower pole section and turn counter-clockwise to loosen
Prevent lower pole from falling by holding lower pole section here
Secure assembly by turning collar clockwise: hand tighten as snug as possible
Prevent lower pole from falling by holding lower pole section here
Thread the conduit set-screw through the hole on the end of the lower pole.
Conduit set-screw
1/4”-20 Lock Nut
1/4” Washer
1/4” Washer
3/4” Conduit Set-Screw Connector (included with Clinton Electronics pendant mount)
1/4”-20 Lock Nut
1/4”-20 socket head allen bolt
1/4” Washer
1/4” Washer
400mm Long Safety Cable
1/4”-20 Safety Cable Lock Nut
If drilling is necessary, Use 7/16” metal drill bit to drill through steel mounting surface.
7/16”
CAUTION: This mount is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in instability causing possible injury. This product is intended to mount to a steel support truss, or channel strut.
Hold lower pole section and turn counter-clockwise to loosen
Prevent lower pole from falling by holding lower pole section here
Secure assembly by turning collar clockwise: hand tighten as snug as possible
Prevent lower pole from falling by holding lower pole section here
Thread the conduit set-screw through the hole on the end of the lower pole.
Conduit set-screw
3/4” Conduit Set-Screw Connector (included with Clinton Electronics pendant mount)
1/4”-20 socket head allen bolt
1/4” Washer
1/4” Washer
1/4”-20 Lock Nut
Hold lower pole section and turn counter-clockwise to loosen
Prevent lower pole from falling by holding lower pole section here
CLINTON Electronics 6701 Clinton Road Loves Park, IL 61111
Secure assembly by turning collar clockwise: hand tighten as snug as possible
Prevent lower pole from falling by holding lower pole section here
1.800.447.3306 Sales
1.800.549.6393 Support
www.clintonelectronics.com
1.800.633.8712 Fax
Loading...