
Color profile: Disabled
Composite Default screen
Welcome to the world
of high-technology
vehicle security and convenience
Your Clifford Electronics Prime Level THREE security upgrade package adds extensive security features to
the keyless entry functions of your vehicles factory remote.
TO ARM SECURITY:
Lock the doors with your factory remote control.* The LED inside the car will flash
repeatedly to confirm that the starter motor is electronically immobilized and the
doors will be monitored.
TO DISARM SECURITY:
Unlock the doors with your factory remote control.* The LED will stop flashing and
the system will restore starter motor function. If your system is so equipped, the interior
lights will also turn on and stay on for 30 seconds or until you turn on the ignition.
* If your factory keyless entry system does not provide audible confirmation, the system can be wired to provide
two brief horn beeps upon locking/arming and one beep upon unlocking/disarming.
AutoArming™
This passive arming feature can be turned on (it is factory turned off) to automatically arm and lock 30
seconds after exiting if you forget to use the remote. For programming instructions, call Clifford Prime
Customer Service toll-free at 877-48-PRIME or download from
1
1
D:...31-923 level 3 owners.vp
Mon Jul 26 16:07:59 1999
www.clifford.com/prime
.

Color profile: Disabled
Composite Default screen
Starter AutoImmobilization
While armed, the starter motor is electronically immobilized. An optional triple-point upgrade is
available to additionally immobilize the ignition system and fuel pump for enhanced security.
LED status indicator
Flashing = Armed & Locked Off = Disarmed and unlocked On = Valet mode
Optional CliffNet Wizard™ & DataPort Interface Connector
If you opted to have the Clifford DataPort interface connector installed, you can use our CliffNet
Wizard software to access your Prime system through your Windows 95/98 PC or your Windows CE
palmtop. CliffNet Wizard will show you right on the screen, all programmable feature settings. You can
change settings, customize features, view a chronological history of trigger and sensor activations, and
much more. Its actually fun! To learn more and download this free software, go to
www.clifford.com/wizard
.
Smart prior intrusion attempt alert
If the alarm sounded while you were away, the system will provide 3 horn beeps (if so wired) when you
remotely unlock to alert you to approach with caution.
D:...31-923 level 3 owners.vp
Mon Jul 26 16:07:59 1999
2
2

Color profile: Disabled
Composite Default screen
Smart AutoTesting™
If a
door
is ajar when you remotely arm, youll hear the usual 2 beeps (if so wired), then, 5 seconds later,
4 more beeps (this warning is not possible on vehicles that have delayed or dimming courtesy lights).
Valet Mode
Valet mode lets you override all security features if your factory remote fails or needs a new battery.
Coded valet mode via the valet switch
NOTE: If you lose the use of your remote (lost; dead battery; etc.), you can
turn off the alarm by enabling valet mode.
To enable valet mode, you enter a code on the switch mounted behind the underdash LED assembly.
Entering the code
To enter the code, toggle the valet switch to the left 2 times, then once to the right.
The system’s factory-set valet code is 2: left, left, right.
To set your own code, request programming instructions from Clifford Prime Customer Service at
877-48-PRIME or download from
www.clifford.com/prime
3
.
D:...31-923 level 3 owners.vp
Mon Jul 26 16:07:59 1999
3

Color profile: Disabled
Composite Default screen
To enable valet mode
1. Turn the ignition on or start the engine (you may also do this while the engine is running).
2. Enter your valet code (factory-set valet code is 2: left, left, right) on the switch mounted behind the LED
assembly.
3.
Continue
holding the switch to the right for 5 seconds, then release. The LED will stay on for
ongoing visual confirmation of valet mode.
To exit valet mode and restore normal operation
1. Turn the ignition on or start the engine (you may also do this while the engine is running).
2. Enter your valet code (left, left, right). The LED will turn off.
User-selectable features
Many of your Prime systems features can be changed via a programming procedure. To do so, request
programming instructions by calling Clifford Prime Customer Service toll-free at 877-48-PRIME or
download from
www.clifford.com/prime
. Or use the CliffNet Wizard Windows software (see page 2).
© Clifford Electronics 1999 31-923B/P3om/0799
D:...31-923 level 3 owners.vp
Mon Jul 26 16:08:00 1999
877-48-PRIME www.clifford.com/prime
4
4