Page 1
Color profile: Disabled
Composite Default screen
Welcome to the world
of high-technology
vehicle security and convenience
The remote controls of your Clifford Prime security upgrade are each powered
by a 3-volt lithium battery. Your system is supplied with two remotes: one with
symbols, the other has words. You can buy additional remote controls from
your new vehicle dealer. Your system responds to up to four remote controls.
Remotely controlling your Clifford system
TO LOCK &
ARM SECURITY:
TO UNLOCK &
DISARM SECURITY:
TO PANIC:
TO LOCATE IN LOT:
D:...31-923 level 3 owners.vp
Mon Jul 26 16:08:36 1999
Press the
Lock
button. Two horn beeps (and two parking light flashes, if your system
is so wired) confirm remote arming & locking and the LED inside the car will flash
repeatedly. If you have the SmartWindows 4 option, the windows automatically close.
Press the
UnLock
button. One horn beep will confirm remote unlocking/disarming
and the LED will stop flashing. If your system is so equipped, the interior lights will
also turn on and stay on for 30 seconds or until you turn on the ignition.
Press and
for 30 seconds or until you press the
Press (but do not hold) the
HOLD
the
Panic
button for three seconds. The horn will honk repeatedly
Panic
button again to turn off panic mode.
Panic
button. If within range, the horn will beep.
1
Page 2
Color profile: Disabled
Composite Default screen
TO OPEN TRUNK:
OPTION 2:
TO ENGAGE VALET
MODE OR RETURN TO
NORMAL OPERATION:
TO REMOTELY
START THE ENGINE:
TO ENGAGE THE
AUTOSTART OR
SAFESTART FEATURE:
TO REMOTELY OPEN
OR VENT WINDOWS:
D:...31-923 level 3 owners.vp
Mon Jul 26 16:08:37 1999
If your system is so equipped, press the
If your system is so equipped, press the
Simultaneously press the
Opt+UnLock
Opt
button to pop the trunk release.
Opt+Lock
buttons to activate option 2.
buttons. The LED will stay on to
confirm valet mode. Press this combination again to return to normal operation
(LED will turn off). See the Valet Mode section for details on this feature.
If so equipped, press the
(for manual transmission, see the next item). See the
Lock+UnLock
buttons to remotely start the engine
DOs and DONTs
section of the IntelliStart 4 users manual for details on this feature. If your system
does not have this feature, the optional IntelliStart 4 accessory can be added.
If so equipped, simultaneously press the
Lock+Panic
buttons to engage the
remote engine starting LowBattery/ LowTemp AutoStart or the manual
transmission SafeStart functions noted in the IntelliStart 4 operations manual.
If equipped with the SmartWindows 4 option, pressing the
Opt+Panic
buttons
immediately after remote unlocking will open the windows. Or, right after locking,
this combination vents the windows slightly while the system remains armed.
2
Page 3
Color profile: Disabled
Composite Default screen
Automatic remote control low-battery warning
If your remote control battery is low, youll hear 5-beeps when you disarm instead of the usual one beep.
Replacement batteries are available from your new vehicle dealer or any Authorized Clifford Dealer.
Starter AutoImmobilization
While armed, the starter motor is electronically immobilized. An optional triple-point upgrade is
available to additionally immobilize the ignition system and fuel pump for enhanced security.
LED status indicator
Flashing = Armed & Locked Off = Disarmed and unlocked On = Valet mode
Optional CliffNet Wizard™ & DataPort Interface Connector
If you opted to have the Clifford DataPort interface connector installed, you can use our CliffNet
Wizard software to access your Prime system through your Windows 95/98 PC or your Windows CE
palmtop. CliffNet Wizard will show you right on the screen, all programmable feature settings. You can
change settings, customize features, add or delete remote controls, change remote control button
assignments, view a chronological history of trigger and sensor activations, and much more. Its actually
fun! And secure. To learn more and download this free software, go to
3
www.clifford.com/wizard
.
D:...31-923 level 3 owners.vp
Mon Jul 26 16:08:37 1999
3
Page 4
Color profile: Disabled
Composite Default screen
User-Selectable AutoLock and AutoUnLock™
For safety, the power door locks automatically lock the instant you turn on the ignition. When you turn
the ignition off, they automatically unlock (some vehicles are incompatible with these features).
Smart prior intrusion attempt alert
If you hear 3 beeps when you disarm instead of the usual 1 beep, it means that the alarm sounded while
you were away. Approach with caution.
Smart AutoTesting™
If a
door
is ajar when you remotely arm, youll hear the usual 2 beeps, then, 5 seconds later, there will be
4 more beeps (this warning is not possible on vehicles that have delayed or dimming courtesy lights).
AutoArming™
This passive arming feature can be turned on (it is factory turned off) to automatically arm and lock
30 seconds after exiting if you forget to use the remote. For programming instructions, call Clifford
Prime Customer Service toll-free at 877-48-PRIME or download from
www.clifford.com/prime
.
D:...31-923 level 3 owners.vp
Mon Jul 26 16:08:37 1999
4
4
Page 5
Color profile: Disabled
Composite Default screen
Valet Mode
Valet mode allows you to silence the alarm and override all security features if your Clifford system is
not responding to the remote control (if, for example, the remote control battery is dead). You can
engage valet mode via the remotes
Opt+UnLock
buttons as noted and via the valet switch:
Coded valet mode via the valet switch
NOTE: If you lose the use of your remote (lost; dead battery; etc.), you can
turn off the alarm by enabling valet mode.
To enable valet mode, the driver must enter a valet code on the valet switch mounted behind the
underdash LED assembly.
Entering a code
To enter a code, toggle the valet switch to the left 2 times, then once to the right.
The system’s factory-set valet code is 2: left, left, right.
To set your own code, request programming instructions from Clifford Prime Customer Service at
877-48-PRIME or download from
www.clifford.com/prime
.
D:...31-923 level 3 owners.vp
Mon Jul 26 16:08:38 1999
5
5
Page 6
Color profile: Disabled
Composite Default screen
To enable valet mode
1. Turn the ignition on or start the engine (you may also do this while the engine is running).
2. Enter your valet code (factory-set valet code is 2: left, left, right) on the switch mounted behind the LED
assembly.
3.
Continue
holding the switch to the right for 5 seconds, then release. The LED will stay on for
ongoing visual confirmation of valet mode.
To exit valet mode and restore normal operation
1. Turn the ignition on or start the engine (you may also do this while the engine is running).
2. Enter your valet code (left, left, right). The LED will turn off.
User-selectable features
Many of your Prime systems features can be changed via a programming procedure. To do so, request
programming instructions by calling Clifford Prime Customer Service toll-free at 877-48-PRIME or
download from
www.clifford.com/prime
. Or use the CliffNet Wizard Windows software (see page 3).
© Clifford Electronics 1999 31-921B/P245om/0799
D:...31-923 level 3 owners.vp
Mon Jul 26 16:08:39 1999
877-48-PRIME www.clifford.com/prime
6
6
Loading...