Page 1
PrimeStart 450 Owner’s Manual
Page 2
I WARNING I
! Always exercise caution and common sense when
operating your PrimeStart system.
! This product is intended for vehicles with fuel-injection
and automatic transmissions only. NEVER attempt to
remote start a vehicle with a manual (stick shift)
transmission. Serious injury may occur with improper
use.
! NEVER attempt to remote start the engine while anyone
(including pets) is in the vehicle.
! NEVER attempt to remote start the engine while the
vehicle is in an enclosed area without sufficient
ventilation.
! NEVER attempt to remote start the engine while the keys
are in the ignition.
! Always be sure the gearshift selector is in "Park" and the
emergency brake is on before attempting to remote start
the vehicle.
! Keep your PrimeStart remote controls out of the reach of
children.
! Whenever the vehicle is being serviced or valet parked,
place the system in Protected Valet Mode to prevent
accidental or unauthorized remote starting. See
"Protected Valet Mode" on page 9.
PrimeStart 450 Owner’s Manual - INSIDE FRONT COVER
Page 3
Table of Contents
PrimeStart 450............................... 2
Lifetime Warranty ............................2
Remote Controls ............................2
Stealth Coding Technology.......................3
Electronic Scan Prevention (ESP)..................... 3
Instant Remote Control Code Deletion .................. 3
One-Step Remote Control Code Learning ................ 3
Valet Switch............................... 3
Operating Your PrimeStart.........................4
Remote-Controlled Door Lock/Unlock.................. 4
Two-Stage Unlock Capability ...................... 4
User-Programmable Ignition-Controlled Door Lock/Unlock ....... 4
User-Programmable RPM Door Lock .................. 4
Remote Panic with Safety Locks™ (capability)..............5
User-Programmable Starter Disable ................... 5
User-Programmable Passive Starter Disable ............... 5
Interior Light Illumination ........................ 5
Remote-Controlled Trunk Release Capability .............. 6
Remote-Controlled Accessory Output .................. 6
Remote Engine Start - Safety and Counter-Theft ............. 6
Remote Engine Start - Operation..................... 7
User-Programmable Temperature-Controlled Starting .......... 8
Pit Stop Mode.............................. 8
Protected Valet Mode ..........................9
User-Programmable Features....................... 10
Programming Table for System Features ................ 11
Pro gram ming Ta ble for Re mote Con trols ................ 12
PrimeStart 450 Owner’s Manual
1
Page 4
PrimeStart 450
Congratulations! You have just purchased the PrimeStart 450, a keyless entry
and remote engine starter system manufactured by Prime Security. You are
about to experience the convenience and luxury of being able to start your
vehicle engine from the comfort of your home, office, department store or
other remote location.
To benefit fully from the capabilities of your PrimeStart system, we encourage
you to read the Owner's Manual thoroughly before using the system. If you
should have any problems or questions regarding your PrimeStart system,
consult the dealer from whom you purchased this product. To locate an
authorized Prime dealer, contact Prime Security directly at 1-800-253-0334
(toll-free within the U.S.) or 1-847-215-2233.
Lifetime Warranty
Prime Security guarantees the operation of your PrimeStart control unit and
remote controls for as long as you own your car. (Please refer to your Lifetime
Limited Warranty Card for complete information.) Make sure that you receive
your warranty card from your dealer, complete the required information and
mail the registration portion to Prime Security. You should retain the top
portion of the warranty card for your records.
Remote Controls
Included with your PrimeStart system are two AviGlo™ 4-button/9-channel
remote controls. Once exposed to light, the AviGlo™ remote control buttons
will glow, making the buttons visible in the dark.
The remote control (remote) is a miniature transmitter powered by a small
+12 volt battery. The RangeMaster™ super-heterodyne receiver (installed in
your vehicle) allows your remote to command your system from up to ¼ mile
away. Obstructions, electrical or radio interference, weather conditions,
window tint or a weak battery can reduce this range. Your remote is the key to
your PrimeStart system and can be used lock and unlock your doors, "pop"
your trunk, start your engine and control optional accessories.
The PrimeStart system can accept up to four Prime remote controls. Additional
remote controls and remote control batteries can be purchased from any
authorized Prime Security dealer, or by calling Prime Security toll-free at
1-800-253-0334 (within the U.S.) or 1-847-215-2233.
2
PrimeStart 450 Owner’s Manual
Page 5
Stealth Coding Technology
Stealth Coding™ technology offers the most advanced protection available
against "code-grabbing" devices which thieves may use to record the digital
code transmitted by your remote control. When you leave the area, thieves
can then play back the code to unlock the doors and deactivate your system.
But Prime Security’s remote controls with Stealth Coding™ randomly change
the code every time you use them, and your system will not respond if any
code is retransmitted. This technology makes code-grabbing devices useless.
Electronic Scan Prevention (ESP)
Your PrimeStart system also includes ESP, which blocks electronic scanner
codes to prevent unauthorized operation of your system.
Instant Remote Control Code Deletion
In the event of a lost or stolen remote control, all remote controls can be
erased from the system’s memory to prevent unauthorized system operation.
(See the "Programming Table for Remote Controls" on page 12).
One-Step Remote Control Code Learning
The PrimeStart system allows you to add new remote controls in one step. (See
the "Programming Table for Remote Controls" on page 12).
Valet Switch
The valet switch is a small hidden toggle switch which allows you to control
all of the system’s programmable features. (See the "User-Programmable
Features" on page 10). This switch can only be controlled with the use of your
ignition key.
NOTE: Be sure to have your dealer show you where the valet switch is located.
PrimeStart 450 Owner’s Manual
3
Page 6
Operating Your PrimeStart
Remote-Controlled Door Lock/Unlock
To Lock the Doors:
Press the remote control LOCK button for 1-2 seconds. The doors will lock,
the parking lights will flash twice and the dash mounted LED will flash slowly.
If the Remote Lock Starter Disable feature was programmed ON, the vehicle
starter motor will be disabled . (See the "Programming Table for System
Features" on page 11.)
To Unlock the Doors:
Press the remote control UNLOCK button for 1-2 seconds. The doors will
unlock. The interior lights will turn on for 30 seconds or until the ignition key
is turned on. The parking lights will flash once and the dash mounted LED will
turn off. If the Remote Lock Starter Disable feature was programmed ON, it
will disengage allowing you to start the vehicle engine.
Two-Stage Unlock Capability
If the optional Two-Stage Unlock feature was installed, press the UNLOCK
button for 1-2 seconds and only the driver door will unlock. Within 3
seconds, press the UNLOCK button again and the passenger doors will unlock
(may require an optional relay).
User-Programmable Ignition-Controlled Door Lock/Unlock
For the ultimate in security and convenience, the PrimeStart can be
programmed to automatically lock your doors when the ignition key is turned
on or the engine is started, and will unlock when the ignition key is turned off.
This feature can be programmed ON or OFF. (See the "Programming Table for
System Features" on page 11.)
User-Programmable RPM Door Lock
The system can be programmed to automatically lock the doors when the
engine reaches the factory preset RPM level. (See the "Programming Table for
System Features" on page 11).
When you begin driving, your vehicle doors will automatically lock. When
you turn the ignition key off, the doors will automatically unlock.
NOTE: Ignition-Controlled Door Lock feature must be programmed OFF.
4
PrimeStart 450 Owner’s Manual
Page 7
Remote Panic with Safety Locks™ (capability)
In a threatening situation, you can activate Remote Panic with Safety Locks .
When activated, the siren/horn will sound and the parking lights will flash. If
you are inside your vehicle and the ignition key is "ON," the doors will lock. If
you are outside the vehicle with the ignition key "OFF," the doors will unlock
allowing you to move to safety. (Requires the addition of a siren or interfacing
with your vehicle horn.)
To Activate:
1. Press the remote control LOCK button for 3-4 seconds.
2. The siren/horn will sound and the parking lights will flash.
3. If the ignition key is "OFF," the doors will unlock. If the ignition key is
"ON," the doors will lock.
To Deactivate:
1. Press the remote control LOCK button for 1-2 seconds.
2. The siren/horn will shut off and the parking lights will stop flashing.
User-Programmable Starter Disable
The PrimeStart can be programmed to electronically disable the vehicle starter
every time the doors are remote locked. (See the "Programming Table for
System Features" on page 11).
User-Programmable Passive Starter Disable
Your PrimeStart system can be programmed to automatically disable the
vehicle starter whenever you exit the vehicle. (See the "Programming Table for
System Features" on page 11.)
To Activate:
1. Turn the iginition key "OFF." The LED will begin to flash rapidly.
2. After 30 seconds, the LED will flash slowly and the starter will be disabled.
To Deactivate:
1. Press the remote UNLOCK button for 1-2 seconds.
Interior Light Illumination
When you remote unlock the doors, PrimeStart will turn on the vehicle
interior light(s) for 30 seconds or until the ignition key is turned on.
PrimeStart 450 Owner’s Manual
5
Page 8
Remote-Controlled Trunk Release Capability
If you have the optional Trunk Release installed, simply press the remote
control TRUNK button for 1-2 seconds to activate your vehicle electronic
trunk release. The trunk will "pop" open (may require an optional relay).
Remote-Controlled Accessory Output
This output allows you to add a remote-controlled optional accessory such as
a window roll-up or fuel door release. To activate your optional accessory, see
the "Programming Table for Remote Controls" on page 12.
Remote Engine Start - Safety and Counter-Theft
CAUTION : Be sure to read the "WARNING" bulletin on the inside
cover of this manual before attempting to operate remote start.
I
Automatic Safety and Counter-Theft Features
Before remote starting your engine, the PrimeStart system will automatically
perform a safety check to ensure the following conditions have been met:
• Brake pedal is not depressed.
• Engine and ignition are turned off.
• Hood is closed.
After remote starting your engine, the PrimeStart system will shut off the
engine immediately if the ignition is OFF and any of the following occurs:
• The hood is opened.
• The engine RPM rises above preset level.
• The brake pedal is pressed.
• The remote control START button is pressed.
• The 20 or 30 minute programmable run time expired.
Visual Fault Indication
The PrimeStart has a built-in fault detection system that automatically scans all
of the safety zones, prevents the system from remote starting and provides a
visual indication if a fault is detected. The parking lights will flash 1 time if the
hood is opened or 3 times if the brake pedal is depressed and will not allow
the engine to start. If this occurs, bring your vehicle to your authorized Prime
Security dealer for service.
6
PrimeStart 450 Owner’s Manual
Page 9
Remote Engine Start - Operation
Your PrimeStart system will start your vehicle engine with a touch of a button
on your AviGlo™ remote control. To also cool or warm the interior of your
vehicle before you enter, set the climate control to your preference (heater,
defrost or air conditioning) before remote starting . Set the fan to a medium
speed (not maximum). Ensure the vehicle is in "Park" and the key is not in the
ignition.
To Remote Start the Engine:
1. Press the remote control START button for 1-2 seconds, 10-15 minutes
before you enter the vehicle (this will allow the climate control time to
heat or cool the vehicle.) The parking lights will flash 2 times, the engine
will start and the parking lights will remain on as a visual indication that
the engine is running. PrimeStart will automatically lock the doors when
the engine is remote started. If you have a diesel engine, the PrimeStart
will be programmed to start 15 seconds after the parking lights flash 2
times. This will allow time for the glow plugs to heat up.
2. If the engine does not remote start, the PrimeStart system will attempt to
start the engine two additional times.
3. If the vehicle is left unattended, the engine will run for 20 minutes and then
shut off automatically. You can also program the system to run the engine for
30 minutes. (See the "Programming Table for System Features" on page 11.)
To Operate the Vehicle While Remote Started:
1. Press the remote control UNLOCK button for 1-2 seconds. The doors will
unlock.
2. Enter the vehicle (do not touch the brake pedal), turn the ignition key to the
"ON" position and then press the brake pedal. Pressing the brake pedal will
shut off the remote start and parking lights but the engine will remain
running.
3. You can now drive the vehicle.
To Shut Off Remote Start:
At any time while the engine is remote started, you can shut the engine off
with the remote control by pressing the remote control START button for 1-2
seconds. The engine and parking lights will shut off.
PrimeStart 450 Owner’s Manual
7
Page 10
User-Programmable Temperature-Controlled Starting
CAUTION : Do not activate Temperature-Controlled Starting while
the vehicle is in an enclosed area.
I
The PrimeStart system can be programmed to automatically start the vehicle
engine whenever the temperature inside the vehicle reaches or drops below
the preprogrammed temperature level. The PrimeStart will monitor the air
temperature every 2½ hours and will only start the engine during extreme
cold temperatures. There are three temperature levels to choose from. (This
feature is programmed OFF from the factory and must be programmed ON to
operate. (See the "Programming Table for System Features"on page 11).
To Activate:
Press the remote control LOCK and START buttons at the same time. The
parking lights will turn on for 3 seconds, shut off for 1 second and turn on for
3 seconds. This will be your visual indication that you have activated the
Temperature-Controlled Starting feature.
When the temperature inside the vehicle reaches the preprogrammed
temperature level, the parking lights will flash 2 times, the vehicle will start
and the parking lights will turn on. The vehicle will run for 10 minutes and
then shut off. This will allow the engine to warm up and charge the battery.
To Deactivate:
Press the remote control LOCK and START buttons at the same time for 1-2
seconds. The parking lights will turn on for 3 seconds and then turn off. This
will be your visual indication that you have deactivated the TemperatureControlled Starting feature.
NOTE : At any time, if the ignition key is turned on or the vehicle is remote
started, the Temperature-Controlled Starting feature will deactivate.
Pit Stop Mode
CAUTION : Do not leave passengers or pets in the vehicle while the
system is in Pit Stop Mode.
I
The Pit Stop Mode allows you to park the vehicle for short-term stops, remove
the ignition key and leave the engine running.
8
PrimeStart 450 Owner’s Manual
Page 11
To Activate:
1. While the vehicle engine is running with the ignition key turned on, press
the remote control START button for 1-2 seconds. The parking lights will
flash 2 times and then stay on. (Make sure the vehicle is in "Park" and set
the emergency parking brake.)
2. Turn the ignition key off and the engine will stay running.
3. Remove the ignition key and remote control and exit the vehicle.
Remember to keep the ignition key and remote control in your possession.
4. Press the remote control LOCK button for 1-2 seconds to secure your vehicle.
To Deactivate:
1. When you return to the vehicle, press the remote control UNLOCK button
for 1-2 seconds. The doors will unlock.
2. Enter the vehicle (do not touch the brake pedal), turn the ignition key to the
"ON" position and then press the brake pedal. The parking lights will shut
off and you will now be able to drive the vehicle.
Protected Valet Mode
You should place your system in Protected Valet Mode whenever your vehicle
is being serviced by mechanics, car wash personnel or driven by valet parking
attendants. While in the Protected Valet Mode, all remote starter functions are
bypassed to prevent unauthorized or accidental operation. If a remote start is
attempted, the parking lights will flash 4 times and the vehicle will not start.
Remote controlled door lock/unlock and trunk release will still operate.
To Turn on Protected Valet Mode:
1. Turn the ignition key to the "ON" position or start the engine.
2. Flick the valet switch to the "ON" position.
3. The LED will turn on solid red to indicate the system is in the Protected
Valet Mode.
4. Turn the ignition key to the "OFF" position.
To Turn off Protected Valet Mode:
1. Turn the ignition key to the "ON" position or start the engine.
2. Flick the valet switch to the "OFF" position.
3. The LED will turn off to indicate the system is no longer in the Protected
Valet Mode.
4. Turn the ignition key to the "OFF" position.
PrimeStart 450 Owner’s Manual
9
Page 12
User-Programmable Features
All PrimeStart system and remote control programmable features are
accomplished by turning the ignition key on (or starting the engine) and
flicking the valet switch on and off a preset number of times.
The PrimeStart also allows you to add new remote controls in one step, delete
lost or stolen remote controls or rearrange the factory preset remote control
functions.
1. Remove the system from Protected Valet Mode. Programming cannot be
accessed while the system is in Protected Valet Mode indicated by the LED
on solid red.
2. Select the feature you wish to program from the "Programming Table for
System Features" or the "Programming Table for Remote Controls" on
pages 11 and 12. Note the number of beeps associated with that feature.
3. Turn the ignition key to the "ON" position.
4. Within 10 seconds, begin flicking the valet switch on and off. The built-in
piezo beeper will beep once each time you flick the switch on then off.
5. Continue flicking the switch on and off, counting the number of beeps.
NOTE: Stop when you reach the number of beeps associated with
your chosen feature.
6. Follow the "Secondary Action." You will hear a number of beeps to
confirm that you have changed the setting of that feature.
7. Turn the ignition key to the "OFF" position.
8. Repeat steps 1-7 for any other feature you wish to program.
10
PrimeStart 450 Owner’s Manual
Page 13
Programming Table for System Features
Feature
Ignition-Controlled Door
Lock/Unlock
0 or 3 Second Delay for
Ignition-Controled Door Lock
RPM Door Locking OFF 8
Passive Starter Disable OFF 9
Remote Lock Starter Disable ON 10
Remote Start Run Time
20 or 30 Minutes
Temperature-Controlled
Starting
OFF or 5 °F (-15 °C)
Temperature-Controlled
Starting
-7 °F (-20 °C) or -22°F (-30 °C)
Factory
Setting
On 6
0 Second 7
20
Minutes
OFF 15
— 16
No. of
Beeps
Secondary Action
Wait 3 seconds, the piezo beeper will
beep once for OFF, twice for ON.
Wait 3 seconds, the piezo beeper will
beep once for 3 seconds, twice
for 0 seconds.
Wait 3 seconds, the piezo beeper will
beep once for OFF, twice for ON.
Wait 3 seconds, the piezo beeper will
beep once for OFF, twice for ON.
Wait 3 seconds, the piezo beeper will
beep once for OFF, twice for ON.
13
Wait 3 seconds, the piezo beeper will
beep once for 30 minutes, twice
for 20 minutes.
Wait 3 seconds. The piezo beeper will
beep once for OFF, twice for 5°F
(-15°C).
Wait 3 seconds. The piezo beeper will
beep once for -7 °F (-20°C), twice for
-22 °F (-30°C).
PrimeStart 450 Owner’s Manual
11
Page 14
Pro gram ming Ta ble for Re mote Con trols
Feature
Remote Door Lock/Panic
Remote Door Unlock
Remote Engine Start
Remote Trunk Release
Temperature Controlled Start
Active/Inactive
Remote Accessory Output (-)
One-Step Remote Control Code
Learning
Instant Remote Control Code
Deletion
Factory
Setting
LOCK
Button
UNLOCK
Button
START
Button
TRUNK
Button
LOCK +
START
Buttons
LOCK +
UNLOCK
Buttons
LOCK
Button
— 24
# of
Beeps
17
18
19
20
21
22
23
Secondary Action
Press the LOCK Button, the piezo
beeper will beep 1 time.
Press the UNLOCK Button, the piezo
beeper will beep 2 times.
Press the START Button, the piezo
beeper will beep 3 times.
Press the TRUNK Button, the piezo
beeper will beep 4 times.
Press the LOCK + START Button, the
piezo beeper will beep 5 times.
Press the LOCK + UNLOCK Button,
the piezo beeper will beep 6 times.
Press the LOCK Button, the piezo
beeper will beep 1 time.
Wait 3 seconds, the piezo beeper will
beep twice, all codes are erased
out of memory.
12
PrimeStart 450 Owner’s Manual
Page 15
PrimeStart 450 Owner’s Manual
Page 16
Loading...