CLICKER MODEL CLK1 
The Clicker can be programmed to operate with different brands of garage door openers.
It is compatible with most garage door opener systems manufactured by Chamberlain, Do It, Genie, LiftMaster, Linear, Master Mechanic, Moore-O-Matic, Multi-Code, Sears and Stanley.
1 
2 
3 
4 
5 
6 
7 
Dip Switches or Smart-Learn Button
THE CLICKER IS NOT COMPATIBLE WITH SOME ROTATING SUCH AS GENIE INTELLICODE OR STANLEY SECURE CODE OPENER SYSTEMS DEVELOPED BY SEVERAL MANUFACTURERS
Identify Your Garage Door Opener
Determine your brand from an original hand held remote or receiver. The receiver can be mounted on the back or side panel or could be mounted on the ceiling or wall.
SECTION BRAND
1Chamberlain, Sears, LiftMaster, Master Mechanic,
(9 Code Switch Systems, Yellow, White or Gray
2Chamberlain, Sears, LiftMaster, Master Mechanic,
(Green Learn Button)
3Chamberlain, Sears, LiftMaster,
Master Mechanic, Do It - (Orange/Red Learn
4Linear, Moore-O-Matic
5 |
Genie - (9 Code Switch Systems) |
Circle your |
6 |
Genie - (12 Code Switch Systems) |
Brand and |
7 |
Multi-Code |
proceed to the |
8 |
Stanley |
appropriate |
|
|
section. |
Helpful Hints
You must choose a 4-digit Personal Identification Number (PIN) when programming the CLK1. After programming is complete, your PIN plus any additional number must be entered to activate your system.
If an incorrect PIN is entered, the keypad flashes. When flashing stops, just re-enter the correct PIN followed by any 5th additional number. (Do not use the or # Key)
Clear and start over: Press and # together until keypad stops flashing
(5 one second flashes). If both keys are not pressed down at the same time, the keypad flashes 10 1/2 second flashes, followed by 5 one second flashes. This erases previous programming and returns unit to unprogrammed factory setting.
Keypad will flash: During certain programming sequences - when pressing the or # key or an incorrect PIN is entered.
To program a second garage door opener brand after successfully programming the first: Determine brand, then follow the brand steps, choosing a different PIN and in step 1 enter 5,6,7,8 instead of 1,2,3,4. If unsuccessful, wait until keypad stops flashing, then begin at step 1. Do not clear and start over as first door programming will be erased.
Keypad will light steadily for 5 seconds: After pressing any key or after entering a correct PIN. Once programmed, the keypad remains active for 15 seconds. During this time you may stop, reverse or reactivate the door by pressing any number on the keypad.
MOUNTING THE CLK1
Select a smooth vertical surface. Mount the keypad out of the path of the moving garage door, but within sight of it. At least 4 inches of clearance is needed above the keypad in order to slide the cover up.
Slide outside cover up and remove. Remove battery cover. Take battery out of compartment (it is not necessary to disconnect it). Mount the keypad using the two mounting holes and screws supplied, then reinsert battery, replace battery cover, and slide outside cover down.
CHANGING YOUR PIN
It is not necessary to reprogram the CLK1 to change the existing PIN. To change your PIN:
Enter existing 4-digit PIN and the key.
Enter new 4-digit PIN and the key.
To test, enter new 4-digit PIN followed by any 5th additional number.
Note: Do not use the or # keys as a 5th number.
Wireless Keypad - For use with Garage Door Openers
WARNING
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
•ALWAYS keep keypads out of reach of children. NEVER permit children to operate, or play with remote control transmitters/keypads.
•Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
•ALWAYS keep gate or garage door in sight until completely closed. Never permit anyone to cross path of moving gate or door.
BATTERY REPLACEMENT
Replace the 9-volt battery when the keypad light becomes dim or does not light up. Slide the outside cover up, unscrew the battery cover and replace battery. It may be necessary to reprogram the keypad after battery is replaced.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CHAMBERLAIN, SEARS, LIFTMASTER,
MASTER MECHANIC, DO IT - SECTIONS 1, 2 AND 3
Determine if your system has code switches or a smart-learn button. If your system has code switches they can be found in an original hand held remote or on the motor unit receiver. The receiver can be mounted on the side or back panel of the motor unit or could be mounted on the ceiling or wall (locate the small gray wire antenna). If you have code switches proceed to Section 1.
1 CODE SWITCH SYSTEMS
If the switch is in the plus (+) position place a 1, neutral (0) position place a 2, negative (-) position place a 3 in the corresponding box in the TABLE below.
If you do not have an 8th or 9th switch on your codes, switches 8 & 9 are in the
(0) position.
CODE SWITCH SEQUENCE 1 2 3 4 5 6 7 8 9
0
–
Exception: If your original hand held remote has 3 buttons and you are using the small button on left, place a 1; center button, place a 2; large button place a 3 in box 1 in the table above. Boxes 2 through 9, place number that corresponds with switch position.
Choose a 4-digit Personal Identification Number (PIN). Any combination of numbers from 0 to 9 may be used.
Write PIN here:
PROGRAMMING
Before initial programming, press and # together until keypad stops flashing. This erases
previous programming and returns unit to unprogrammed factory setting.When programming to more than one door, do not clear keyless after a successful programming of the first door.
Step 1 Door 1, Enter 1 2 3 4 and the key. or Door 2, Enter 5 6 7 8 and the key.
Step 2 Enter your PIN and the key. Step 3 Enter your PIN and the # key. Step 4 Enter 1 and the # key.
Step 5 Enter code in sequence from the TABLE above and the # key. Programming is complete.
To test, enter PIN followed by any 5th additional number.
Note: Do not use the star or # pound keys as a 5th number.
If programming is unsuccessful, Check to be sure the code from TABLE above match’s switch positions from your system. Clear and start over.
If you did not have any remotes and you set a 9 digit random code and you have a yellow, white or gray smart-learn button, press the smart-learn button and release it. Enter your 4-digit pin number and hold any additional number, the door should operate. Programming is complete.
2 GREEN LEARN BUTTON
3 ORANGE/RED LEARN BUTTON SYSTEMS WITH SMART-LEARN BUTTON
Locate your smart-learn button on your system. It will be located on the side or back panel of the motor unit (near the small grey wire antenna).
The original hand held remote will not have code switches.
Choose a 4-digit Personal Identification Number (PIN). Any combination of numbers from 0 to 9 may be used.
Write PIN here:
PROGRAMMING
Before initial programming, press and # together until keypad stops flashing. This erases previous
programming and returns unit to unprogrammed factory setting. When programming to more than one door, do not clear keyless after a successful programming of the first door.
Step 1 Door 1, Enter 1 2 3 4 and the key. or Door 2, Enter 5 6 7 8 and the key.
Step 2 Enter your PIN and the key. Step 3 Enter your PIN and the # key.
Step 4 GREEN LEARN BUTTON Enter 2 and the # key.
or ORANGE LEARN BUTTON Enter 3 and the # key. Wait 10 seconds. Step 5 Press and release smart-learn button on motor unit. (indicator light
next to smart-learn button should turn on.) Step 6 Enter your PIN into the keypad.
Step 7 Press and HOLD any additional number on the keypad until the indicator light next to the smart-learn button blinks.
Note: Do not use the or # keys as a 5th number.
Programming is complete. Wait 10 seconds.
the keypad remains active for 15 seconds. During this time you or reactivate the door by pressing any number on the keypad.
followed by any 5th additional number. the or # keys as the 5th number.
4 LINEAR AND MOORE-O-MATIC
Locate your systems code switch positions from an original hand held remote or the motor unit receiver. If the switch is “on” or “up”, place a 1; “off” or “down”, place a 2 in the corresponding box in the TABLE below.
CODE SWITCH SEQUENCE 1 2 3 4 5 6 7 8
ON/UP
OFF/DOWN
Choose a 4-digit Personal Identification Number (PIN). Any combination of numbers from 0 to 9 may be used.
Write PIN here:
Before initial programming, press |
PROGRAMMING |
|
|
together until keypad stops flashing. |
|
previous programming and returns unit to |
factory setting.When |
programming to more than one door, do not clear keyless after a successful programming of the first door.
Step 1 |
Door 1, Enter 1 2 3 4 and the key. |
|
|
or Door 2, Enter 5 6 7 8 and the |
. |
Step 2 |
Enter your PIN and the key. |
|
Step 3 |
Enter your PIN and the # key. |
|
Step 4 |
Enter 4 and the # key. |
|
Step 5 |
Enter code in sequence from the |
above and the # key. |
|
Programming is complete. |
|
|
|
To test enter PIN followed by any 5th additional number.
Note: Do not use the star or # pound keys as a 5th number.
If programming is unsuccessful:
•Clear and start over.
•Check to be sure code from table above matches switch positions.
•Reverse code from table above (change 1 to 2; 2 to 1)
5 GENIE (9 CODE SWITCH SYSTEMS)
6 GENIE (12 CODE SWITCH SYSTEMS)
Locate your systems code switch positions from an original hand held remote or the motor unit receiver. If the switch is “on” or “up”, place a 1; “off” or “down”, place a 2 in the corresponding box in the TABLE below.
CODE SWITCH SEQUENCE 1 2 3 4 5 6 7 8 9 10 11 12
ON/UP
OFF/DOWN
Choose a 4-digit Personal Identification Number (PIN). Any combination of numbers from 0 to 9 may be used.
Write PIN here:
|
|
|
|
PROGRAMMING |
|
Before initial programming, press |
and # |
||||
|
|||||
together until keypad stops flashing. This erases
previous programming and returns unit to unprogrammed factory setting. When programming to more than one door, do not clear keyless after a successful programming of the first door.
Step 1 Door 1, Enter 1 2 3 4 and the key. or Door 2, Enter 5 6 7 8 and the key.
Step 2 Enter your PIN and the key. Step 3 Enter your PIN and the # key.
Step 4 GENIE (9 Code Switch Systems) - Enter 5 and the # key.
or GENIE (12 Code Switch Systems) - Enter 6 and the # key.
Step 5 Enter code in sequence from the TABLE above and the # key. Programming is complete.
To test enter PIN followed by any 5th additional number.
Note: Do not use the star or # pound keys as a 5th number.
If programming is unsuccessful:
•Clear and start over.
•Check to be sure code from table above matches switch positions.
•Reverse code from table above (change 1 to 2; 2 to 1)
7 MULTI-CODE ï 8 STANLEY
Locate your systems code switch positions from an original hand held remote or the motor unit receiver. If the switch is “on” or “up”, place a 1; “off” or “down”, place a 2 in the corresponding box in the TABLE below.
CODE SWITCH SEQUENCE 1 2 3 4 5 6 7 8 9 10
ON/UP
OFF/DOWN
Choose a 4-digit Personal Identification Number (PIN). Any combination of numbers from 0 to 9 may be used.
Write PIN here:
PROGRAMMING
Before initial programming, press and # together until keypad stops flashing. This erases
previous programming and returns unit to unprogrammed factory setting. When programming to more than one door, do not clear keyless after a successful programming of the first door.
Step 1 Door 1, Enter 1 2 3 4 and the key. or Door 2, Enter 5 6 7 8 and the key.
Step 2 Enter your PIN and the key. Step 3 Enter your PIN and the # key.
Step 4 MULTI-CODE - Enter 7 and the # key. or STANLEY - Enter 8 and the # key.
Step 5 Enter code in sequence from the TABLE above and the # key. Programming is complete.
To test enter PIN followed by any 5th additional number.
Note: Do not use the star or # pound keys as a 5th number.
If programming is unsuccessful:
•Clear and start over.
•Check to be sure code from table above matches switch positions.
•Reverse code from table above (change 1 to 2; 2 to 1)
•Stanley brands try as Multi-Code, Multi-Code brands try as Stanley.
TECHNICAL SUPPORT: 800-442-1255
(MONDAY-FRIDAY 6AM-7PM CST; SATURDAY 8AM-6PM)
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door Corporation. Linear and Multi-Code are Trademarks of Linear Corporation. Master Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. Do It is a Trademark of Do It Best Corporation.
|
©2004, Clicker Corporation |
|
114A2517C |
All Rights Reserved |
Printed in Mexico |
Loading...