Cleveland KGT-12-TGB User Manual

Cleveland

™

P

roject ________________________________

Item __________________________________

Quantity _______________________________

F

CSI Section ____________________________

A

pproval _______________________________

D

ate __________________________________

1333 East 179 St.,

Cleveland, Ohio, U.S.A. 44110

Tel: [phone]

Fax: [phone]

Web Site: www.ClevelandRange.com

Email: [e-mail]

GAS KETTLES

TABLE TOP, GAS-FIRED KETTLES

TILTING with GEARBOX, 2⁄3 STEAM JACKETED
“SPLASH PROOF SERIES”
12 GALLONS (45 LITERS)

Cleveland Standard Features

II

Self contained gas tilting kettle is easily installed, only needs a
gas connection and a 115 volt outlet.

II

Tilt Mechanism of roller bearings and case hardened self­locking worm and segment gear

II

Precise, consistent temperature control, less than 1°C
temperature variance (ideal for simmering). Operating
temperature range from 145°- 260°F (63°C-127°C).

II

“Splash Proof” solid state control panel for temperature,
low water safety, and power “on/off” switch. Accurate L.E.D.
indicators for heat cycle and low water warning.

II

Kettle and all exterior surfaces are a 304 Stainless Steel
with a #4 finish.

II

Energy efficient (65%), high performance gas-fired
heating system for fast heat up and recovery time:

I Twelve gallon model with a 53,000 BTU firing rate, and

I 34,450 BTU directly applied to the product.

II

Supplied with Gas Pressure Regulator.

II

Standard for natural gas operation.

II

Double safety gas shut off turns off the gas when the unit is
tilted.

II

Large pouring lip for easier, faster pouring. Heavy duty
Rolled Rim design provides strong reinforcement, prevents
damages from abuse.

II

“Splash Proof” pressure/vacuum gauge.

II

Steam jacket permanently filled with treated distilled
water, venting and / or refilling is not required.

II

50 PSI Steam Jacket Rating. Safety valve mounted toward
rear of kettle to avoid tampering.

II

Automatic Electronic Spark Ignition System.

II

Supplied with cord and plug for 115 volt controls.

II

Typical approvals include AGA, CSA, NSF and ASME.

Options & Accessories

Ë Stainless Steel equipment stand with sliding drain drawer and

splash shield (ST-28)

Ë Hot and cold water faucet (DPK), or Cold Water (SPK).

Requires bracket (FBKT)

Ë 316 Stainless Steel Liner (316G)

Ë Cooking Baskets (BS)

Ë Food Strainers (FS)

MODELS:  KGT-12-TGB

Short Form Specifications

Shall be CLEVELAND, gas kettle, Table Type, self-contained, tilting,
Model KGT- _____ -T; _____ gallons, natural or LP gas, 2/3 steam jack­eted, type 304 Stainless Steel and supports. Jacket rated at 50 psi
with Safety Valve. Complete with solid state water level, tempera­ture, and safety low water power cut off, including LED indicators.
Optional lift off cover.

Ë Measuring Strips (MS)

Ë Spray Hose (PRS-K)

Ë Lift Off Cover (CL)

Ë Propane Gas Operation (PG)

Ë Kettle Markings (KM)

Ë Protective Control Panel (PCE)

SECT. IX PAGE 1B

0609

DOUBLE
PANTRY
FAUCET
(Optional)

5/16-18 THREADED BUSHING
(FOUR PLACES)

GEARBOX

1

4.50”

(

368mm)

10.00”

(254mm)

14.50”

(368mm)

26.00”

(660mm)

4.00”

(102mm)

33.50”

(851mm)

2

.00” (51mm)

1.75”
(44mm)

27.00”

(686mm)

2

7.00”

(

686mm)

2

3.25”

(591mm)

16.75”

(425mm)

(I.D.)

28.5”

(724mm)

3

.25”

(83mm)

3.88”

(98 mm)

BASE MOUNTING DETAIL

RIGHT: 0, LEFT: 3” (76mm), REAR: 4” (102mm)

CAPACITIES: (in 4 oz. servings, other

•

sizes may be calculated)

12 gallons / 45 liters .......352 servings

Manufacturer must be notified if unit will be operated above 2,000 ft. [610m] altitude.

NOTES:

Cleveland Range reserves right of design improvement or modification, as warranted.
Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes.
Installation of backflow preventers, vacuum breakers and other specific coder requirements is the responsibility of the owner and installer.
Cleveland Range equipment is built to comply with applicable standards for manufacturers. Included among those approval agencies are U.L., A.G.A., NSF, ASME/N.Bd., CSA, CGA, ETL and others.

(NOT TO SCALE)

SECT. IX PAGE 2B

0609

Litho in U.S.A.