Cleveland 36-GM-K1010-200 User Manual

Cleveland

™

P

roject ________________________________

Item __________________________________

Quantity _______________________________

F

CSI Section ____________________________

A

pproval _______________________________

D

ate __________________________________

1333 East 179 St.,

Cleveland, Ohio, U.S.A. 44110

Tel: [phone]

Fax: [phone]

Web Site: www.ClevelandRange.com

Email: [e-mail]

1

0

0

%

5

Y

e

a

r

B

o

i

l

e

r

W

a

r

r

a

n

t

y

N

i

c

k

e

l

G

u

a

r

d

™

MODULAR BASES

MODULAR BASE WITH KETTLES

200M or 300M BTU GAS-FIRED STEAM GENERATOR with NICKELGUARD™
TWO 10 GALLON KETTLES
CABINET BASE: 36" (900MM) WIDE

Cleveland Standard Features

II

Factory assembled Kettle/Steam Generator NickleGard Base
combination with two 10 gallon kettles with 200M or 300M
BTU Gas-Fired Steam Generator

II

Solid State steam generator Water Level Controls

II

Low Water Safety Cut-Off

II

Pressure Limit Controls with 15 psi Safety Valve

II

Type 430 Stainless Steel exterior enclosure, and table top
(with Drain Trough which has 1.50" diameter male drain),
#4 exterior finish

II

Type 304 Stainless kettles, #4 exterior finish

II

Separate "Start/Reset" Illuminated Switch Controls, plus
Pressure Gauge

II

Solid State Electronic Spark Ignition for energy savings

II

Major components serviceable from the front of the unit

II

10 gallon kettles are 2/3 Steam Jacketed and include
Lift-off Covers and Splash Guard

II

Hot and Cold Water Faucet with Swing Spout

II

Kettles have 50 psi Steam Jacket Rating, 50 psi chrome
plated Safety Valves and Manual Tilting, balanced design

II

Tilt Handles can be mounted on right side

II

Steam Generator empties under pressure (blowdown)
automatically upon each Shut-Down, Automatic Water
Refill on Start-Up

II

Standard voltage for controls is 115 volt, 60 Hz,
single phase

II

6" Stainless Steel Legs with Adjustable Flanged Feet (FF-A)

II

Secondary Low Water Cut-Off, factory installed (CALG)

(Required for AZ. AR. CA. CO. CT. DE. FL. GA. HI. IL. IA. KS. MD. MA. MI. MN. MT.
NE. NV. NM. NC. OK. OR. PR. RI. TN. UT. VA. WA. WV., Buffalo, NY, Wash. DC)

MODELS:  36-GM-K1010-200

 36-GM-K1010-300

Short Form Specifications

Shall be CLEVELAND, Modular Cabinet Base with two 10 gallon kettles, Model
36-GM-K1010 -____ , 200M or 300M BTU Nickelguard Gas-Fired Steam
Generator, type 430 Stainless Steel exterior enclosure, Table Top, Back
Splash and 4 level adjustable feet. 2/3 Steam Jacketed type 304 Stainless
Steel kettles with 50 psi Steam Jacket Rating. Console mounted Controls,
Pressure Gauge and Illuminated "Start/Reset" Control Switches. Solid State
Water Level Steam Generator Controls and Electronic Spark Ignition. Steam
Generator drains under pressure (blowdown) after each Shut-Down with
Automatic Water Refill on Start-Up. 15 psi Safety Valve

Options & Accessories

Ë Power Take-Off Kit (GPTO)
Ë Gas, other than natural
Ë Type 316 Stainless Steel kettle interior for high acid food

products (316)

Ë Food Strainers (FS)
Ë Stainless Steel Base Frame (FSS)
Ë Boiler Descaling Pump Kit (107142)

SECT. VII PAGE 31

0609

H

C1

C1

D

D

C2

H

C2

GAS FLUE

2

8.31"

7

19mm

2.03"

52mm

5

.00"

1

27mm

19.00"

482mm

3.50"

89mm

24.00"

610mm

2

5.88"

657mm

2

9.56"

7

51mm

37.00"

940mm

3

.00"

7

6mm

6.12"
155mm

6.68"

170mm

29.65"

753mm

30.81"

782mm

35.43"

900mm

5.38"

137mm

1.38"

35mm

6.00"

152mm

7.50"

191mm

9.00"

229mm

12.50"

318mm

30.00"

762mm

62.00"

1575mm

32.21"

818mm

1.61"

41mm

1.61"

41mm

I.D.

15.75"

400mm

17.00"

432mm

D

C1

C2

D

WATER QUALITY

REQUIREMENT

The recommended minimum water quality
standards whether untreated or pre­treated, based upon 10 hours of use per
day, and a Daily Blowdown, are as follows:

TOTAL DISSOLVED SOLIDS

less than 60 parts per million

TOTAL ALKALINITY

less than 20 parts per million

SILICA

less than 13 parts per million

pH FACTOR

greater than 7.5

CHLORINE

less than 30 parts per million

Consult a local water treatment specialist for
an on site water analysis for recommenda­tions concerning steam generator feed water
treatment (if required), in order to remove or
reduce harmful concentrations of minerals.
The use of highly mineralized water will
mean that more frequent servicing of the
steam generator will be necessary. The fact
that a water supply is potable is not proof
that it will be suitable for the generator.

CAPACITIES: (in 4 oz. servings,

other sizes may be calculated.)

10 Gallon / 36 liters . . . . . . .320 servings

ELECTRIC

50 watts for generator
115 V-1 PH

** Do not connect to GFI outlet. See
note below.

WATER

C1: 1/4" IPS Cold water for boiler
C2: 3/8" NPT Cold water for faucet
C2: 3/8" NPT Hot water for faucet

DRAIN

GAS

NATURAL

3/4" IPS for 200,000

1.00" IPS for 300,000
Supply Pressure

4.00" W.C. Minimum

14.00" W.C. Maximum

NOTES:

**DO NOT CONNECT TO GFI OUTLET. CLEVELAND RANGE RECOMMENDS GAS FIRED 120 VOLT STEAMERS BE HARD WIRED DIRECTLY TO ELECTRICAL SYSTEM.
Cleveland Range reserves right of design improvement or modification, as warranted.
Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes.
Cleveland Range equipment is built to comply with applicable standards for manufacturers. Included among those approval agencies are ASME/N. Bd, UL/NSF#4 and CSA (AGA, CGA).

PROPANE

3/4" IPS for 200,000

1.00" IPS for 300,000
Supply Pressure

12.00" W.C. Minimum

14.00" W.C. Maximum

1 1/2" IPS Common Drain
The floor drain must be

located outside the confines
of the equipment.

Do not connect to any other drain.

CLEARANCES

Right: 6.00"
Left: 6.00"
Rear: 6.00"

(NOT TO SCALE)

SECT. VII PAGE 32

0609

Litho in U.S.A.