Whether you are adding to a wired intercom system or creating
a standalone wireless communications system, the WBS-670
and WBS-680 wireless intercoms are excellent choices. These
systems extend the reach of your communications system in live
performance, studio and mobile television production, industrial
and aerospace applications, or wherever full-duplex wireless
communications are required.
Frequency-agile UHF Operation
The WBS-670 and WBS-680 operate in select frequency
bands between 470-686MHz. Both wireless systems are
supplied with 24 factory-selected, intermodulation-free
frequencies. Select from factory presets or any suitable
frequency in 25KHz increments. 720 Tx and 720 Rx
frequencies can be selected; each from independent
18 MHz operational bands.
Adjustable Transmitter Power
The beltpacks can sense when operating in close proximity
to the base station and intelligently reduce transmitter
output by 10dB. This effectively eliminates overloading
the base station receiver front end which is the primary
cause of “nearfar” densing problems. WBS wireless
system beltpacks operate in normal power mode for
typical distances; a manual high power setting is available
when operating the equipment more than 200ft (160m)
for the base station.
Pre-Selected Compatible
Frequencies and Frequency Scan System setup is easy
with the 24 internal pre-selected and intermodulation-free
frequency groups. Aided by the “ClearScan” function,
base stations and beltpacks can typically be coordinated
and working together within minutes. Memory locations
can be allocated so that particular sets of frequencies can
be chosen, programmed and saved as a new preset.
Graphical User Interface
A clear, backlit LCD screen displays the status of the
beltpacks and provides easy access to all the powerful
features as well as conguration of the operational parameters. The LCD displays which beltpack is transmitting,
operating frequencies, and group/channel status.
Superior Audio Quality and Range
The audio quality of the WBS-670 and WBS-680 wireless
systems is on par with that of professional wired partyline
and digital matrix intercoms. UHF frequencies are ideally
suited for operating through obstacles; a variety of remote
antenna options can help improve range in difcult,
interference-prone production environments.
Seamless Connection to Wired Intercoms
WBS wireless systems can interface with a variety of 2-wire
partyline, 4-wire digital matrix or other wireless intercom
systems. In addition to interfacing with external intercom
systems, the systems provide connections for auxiliary
balanced audio input and output. Wireless Talk-Around
(WTA) and Stage Announce (SA) features are available on
the WTR-680 beltpack.
Rechargeable Battery Option
The battery pack will operate the beltpack in full-duplex
mode for 14 hours with a set of alkaline batteries. The
optional rechargeable NiMH (nickel metal hydride) batteries
will give over 11 hours of continual use. Chargers are
available in single-bay or 4-bay congurations.
2 Clear-Com WBS
WIRELESS INTERCOM SYSTEMS
WBS-670 SINGLE-CHANNEL WIRELESS
The WBS-670 1RU, rack-mountable base station supports
up to four full-duplex wireless beltpacks.
System features:
Full talk/listen headset at the base•
Rear panel connections allow system expansion•
LCD screen displays which beltpacks are transmitting •
the operating frequencies and group/channel status
Input and output level adjustment controls for •
both the connected wired intercom and auxiliary
audio connection
3-pin XLR loop-through connectors for one channel •
of wired partyline intercom at the rear
WTA (Wireless-Talk-Around) button momentarily routes •
audio to only the wireless beltpacks monitoring the
current channel, serving as isolation (ISO) channel
Stage Announce (SA) button allows a (dry) relay signal•
RJ-45 connector for direct connection to a digital 4-wire •
intercom port, and a pair of auxiliary connectors
WBS-680 TWO-CHANNEL WIRELESS
The WBS-680 1RU, rack-mountable base station supports
up to four full-duplex wireless beltpacks.
System features:
Full talk/listen headset at the base•
A pair of efcient, half-wave co-linear antennas is •
supplied with system; A variety of external antennas
may also be used.
WTR-670 BELTPACK FEATURES
Extremely light, durable cast magnesium•
Durable, detachable antennas are secured to the •
beltpack via threaded post connectors
Rear panel connections allow base station to connect •
to two separate channels of wired intercom (2-wire,
4-wire, or both)
Toggle switch enabling the user to communicate with •
either intercom channel A or B (including any wired
intercoms connected at the base station)
LCD screen displays which beltpacks are transmitting •
the operating frequencies and group/channel status
Input and output level adjustment controls for both the •
connected wired intercom and auxiliary audio connection
3-pin XLR loop-through connectors for one channel •
of wired partyline intercom at the rear
WTA (Wireless-Talk-Around) button momentarily routes •
audio to only the wireless beltpacks monitoring the
current channel, serving as isolation (ISO) channel
Stage Announce (SA) button allows a (dry) relay signal, •
which can activate a loudspeaker, two-way radio, IFB,
or any other relay activated device
RJ-45 connector for direct connection to a digital 4-wire •
intercom port, and a pair of auxiliary connectors
A pair of efcient, half-wave co-linear antennas is •
supplied with system; A variety of external antennas
may also be used.
WTR-680 BELTPACK FEATURES
Extremely light, durable cast magnesium•
Durable, detachable antennas are secured to the •
beltpack via threaded post connectors
RF Sensitivity<0.7mV for 12dB SINAD<0.7mV for 12dB SINAD
Signal-to-Noise Ratio95dB95dB
IF Selectivity3dB at 230KHz3dB at 230KHz
Image Rejection70dB or better70dB or better
Squelch Quieting95dB95dB
RF Frequency Stability0.005%0.005%
Distortion<1% at full deviation<1% at full deviation
Local Headset Output40mW output into 600W (1% distortion)40mW output into 600W (1% distortion)
FCC AcceptanceNotification under FCC Part 15Notification under FCC Part 15
Clear-Com WBS 5
BATTERY CHARGERS
WTR1C
The WTR1C is a single battery charger that provides
built-in maintenance capability to maximize the battery
cycle life for the WBS-670 and WBS-680 wireless
intercom systems. It helps to optimize the battery and
maintains the battery’s peak capacity while it is charging.
There is no restriction to how long the battery can remain
in the charger. Rapid Charge capabilities fully charge
batteries in less than 2 hours.
WTR4C
Charging LED - Solid light indicates battery •
pack is charging
Ready LED - Solid light indicates battery •
is fully charged
Rejected LED - Flashing light indicates faulty •
or dead battery
STATUS INDICATORS
The WTR4C has the same features as the WTR1C,
except that the WTR4C can charge up to 4 batteries
simultaneously.
BATTERY FEATURES
Easy-to-read LED status indicator lights•
Battery is fully charged in less than 2 hours•
Maintains battery at peak capacity•
Optimizes battery life•
Battery can remain in charger indenately•
Power LED - Solid light indicates there is power •
to the charging slot
Conditioning Cycle LED - Flashing light indicates •
discharging process
6 Clear-Com WBS
TECHNICAL SPECIFICATIONS
BC-800NM4 & BC-800NM BATTERY CHARGERS
Physical CharacteristicsBC-800NM4BC-800NM
Product Dimensions13” (33cm) W x 1.7” (4.5cm)
H x 7” (17.8cm) D
Product Weight4lbs (1.5kg) without battery adapters1lb, 6oz (0.62kg)
Shipping Dimensions11.5” (29.2cm) W x 10.5” (26.7cm)
H x 18.5” (47cm) D
Shipping Weight10lbs, 9oz (4.8kg) with battery adapters,
Conditioning CycleProvides built-in maintenance capability to maximize battery cycle life
Status Indicators‘Charging’, ‘Ready’, ‘Rejected’ (dead battery), ‘Conditioning Cycle’
and ‘Power LED’ indicators make the BC-800NM simple and easy to use
Intelligent Charging• Optimizes the battery • Battery can remain in the charger indenitely
• Maintains battery at peak capacity
Rapid Charge CapabilityCharges in less than 2 hours
3” (7.62cm) W x 3.5” (8.89cm)
H x 6” (15.24cm) D
7” (17.8cm) W x 4.5” (11.43cm)
H x 7” (17.8cm) D
2lbs, 10oz (1.2kg) with rechargeable
battery pack & power supply
USER ENVIRONMENT
ESD8KV continuous contact discharge; 15KV from air to all surfaces without contact
Humidity95% relative humidity (non-condensing)
DropUnit functions normally after 4ft./1.2m drop to concrete
Storage Temperature-40° to 122oF/-40° to 50°C
Operating Temperature32° to 122°F/0o to 50°C
Power SupplyBC-800NM4: (Universal): 90V-230VAC, 50/60Hz Output: 15VDC, 5A or 24VDC, 4.5A
BC-800NM: (Universal): 90V-230VAC, 50/60Hz Output: 15VDC, 1.5A or 24VDC, 1.3A
Safety StandardsCharger & power supply UL listed (UL 1950), CSA Certified (C 22.2 No. 223);
Compliant to FCC part 15 Class A and CE Marking
(Electromagnetic Compatibility) Directive 89/336/EEC and Low Voltage Directive 73/23/EEC;
C15PR-22 Class B
PERFORMANCE CHARACTERISTICS
Rapid ChargeCharges batteries to 90+% capacity in 2 hours or less
Complete ChargeCompletes 100% capacity charge in 4 hours or less
ConditioningCompletely discharges a battery and automatically switches to charging mode
Maintenance ChargeMaintains the battery at optimum capacity indefinitely
USER INTERFACE
Power LEDIndicates POWER to charging slot
Conditioning/Charging LEDFlashing indicates discharging process
Reject LEDFlashing indicates faulty battery
Conditioning/Charging LEDSolid indicates battery pack is being charged
Ready LEDSolid indicates battery charged
Clear-Com WBS 7
About Clear-Com
®
Clear-Com, an HME company, is a global provider in professional voice communications systems since
1968. We develop and market proven intercom technologies such as Analog & Digital Partyline, Digital
Matrix, Wireless and Intercom-over-IP systems for critical communication applications in broadcast,
performance venues, military, government and enterprise markets. Recognized for our legacy of intercom
innovations, production teams around the world have come to depend on Clear-Com for clear, reliable
and scalable communications solutions.
About HM Electronics, Inc. (HME)
A privately held company founded in 1971, HME has continued to be a leading provider of innovative
technology focused on enhancing productivity and customer service for multiple markets including
pro audio, sports, and restaurants. HME developed the rst wireless intercom system for pro audio and
continues to introduce exciting, cutting-edge wireless intercoms that enhance communications, increase
productivity and facilitate creativity for virtually any application.
www.clearcom.com
Americas and Asia-Pacific Headquarters
California, United States
Tel: +1.510.337.6600
Email: SalesSupportUS@clearcom.com
Europe, Middle East, and Africa Headquarters
Cambridge, United Kingdom
Tel: +44 1223 815000
Email: SalesSupportEMEA@clearcom.com