Clearaudio Innovation Wood, Innovation User Manual

Page 1
Innovation
Clearaudio electronic
®
GmbH
Spardorfer Str. 150 • D-91054 Erlangen • Tel. +49 9131 40300100 • FAX + 49 9131 40300119
www.clearaudio.de • www.analogshop.de • info@clearaudio.de
© Clearaudio electronic GmbH 2016
User manual
Made in Germany
Innovation
Innovation Wood
Picture: Package with Clearaudio tonearm „TT3“ and Clearaudio cartridge „Titanium V2 “.
Picture: Package with Clearaudio tonearm „Universal“ and Clearaudio cartridge „da Vinci V2 “.
Page 2
Dear Clearaudio customer,
Congratulation’s to your choice of the
Innovation / Innovation Wood
(in the following:
Innovation
named)
turntable, a world class turntable, handmade in Germany by Clearaudio electronic GmbH.
Resonance minimizing chassis construction in a sandwich in combination with the innovative motor unit (low noise level and high turning moments), guarantees total isolation of resonances from the turntable chassis, providing the best music reproduction and authentic High End imaging. A high precision, maintenance free sinter bronze bearing is completing the analogue pleasure.
The Clearaudio patented CMB-Bearing-Technology, an inverted bearing with jewelled and polished ceramic bearing shaft and a bronzed liner, provides frictionless analog enjoyment.
Please read this instruction manual carefully, to avoid any damages or loss of warranty. This manual will help you for an easy setup and guarantees the highest pleasure for a long time.
We wish you a lot of musical enjoyments with your new Clearaudio
Innovation
turntable.
Clearaudio electronic GmbH
This section must be read before any connection is made to the mains supply.
Innovation
User manual
WARNINGS
Don’t expose your turntable to rain or humidity. Don’t handle the mains leads with wet hands. Don’t place or insert anything into the equipment or through ventilation holes. No naked ame sources, such as lighted candles, should be placed on the equipment.
CE-MARKING
EQUIPMENT MAINS WORKING SETTING
Your Clearaudio product has been prepared to comply with the household power and safety requirements that exist in your area. This product can be connected to 230 V or 110 V AC (50 Hz and 60 Hz).
COPYRIGHT
Recording und reproduction of any sound-material may require the consent of the creator. Please acknow­ledge the information given in the
- Copyright Act 1956,
- Dramatic and Musical Performers Act 1958,
- Performers Protection Acts 1963 and 1972,
- Any more recent legal regulations.
Page 2 © Clearaudio electronic GmbH 2016
The Clearaudio
Innovation
meets the regulations concerning electromagnetic disturbance
(EMC) and low-voltage appliances.
Page 3
Contents
1. Packing overview 4
2. List of components 5 - 6
3. Installation and setup 7 - 12
4. Fine adjustment of the motor 13
5. Service and special instruction 14
6. Technical data 15
Warranty information 16
Stroboscope Testrecord user manual 17 -18
Page 3© Clearaudio electronic GmbH 2016
Innovation
User manual
Page 4
1. Packing overview
Page 4 © Clearaudio electronic GmbH 2016
Pic. 1: Packing overview
Accessories,
user manual,
warranty card,
Clearaudio Quality
Card,
Stroboscope Testrecord
Innovation
turntable chassis incl.
mounted lower bearing
part and integrated
motor unit;
optional: Tonearm
Stainless steel-sub-
platter; Delrin or Acrylic
platter;
power supply;
upper bearing part and
– cap
optional: Cartridge
Innovation
User manual
Page 5
2. List of components
Clearaudio has developed a special and secure packing for your
Innovation
turntable that ensures a safe transportation. Please keep this original packing, if you need to ship the turntable.
Below you nd the part list of the Clearaudio
Innovation
turntable:
Page 5© Clearaudio electronic GmbH 2016
Pic. 2: List of components
1
2
3
4
7a 7b
1. Turntable body with mounted lower
bearing part
5. Bearing part
2. Stainless steel sub-platter 6. 3 x Flat Pads
3. Delrin or Acrylic (Wood version)
turntable platter
7. Optional: Clearaudio
Universal
(7 a) or
Magnify
(7 b) tonearm with counterweight to
adjust the tracking force
4. Power supply 8. Mounting clip for stainless steel sub-platter and hex key
Pic. 7b: Clearaudio
Magnify
tonearm
Pic. 7a: Clearaudio
Universal
tonearm
5
6
8
Innovation
User manual
Page 6
Continuation of components list
Page 6 © Clearaudio electronic GmbH 2016
9
10
11
12 13 14
15 16 a 17
9. 1 Pair of white gloves 15. Bearing oil for occasional use
10. Grounding - wire for the Innovation
turntable (to connect in the bottom bearing part)
16 a
16 b
Optional in package: Clearaudio MC cartridge
da Vinci
Clearaudio MC cartridge
Talismann
Clearaudio
Smart Stylus Gauge
11. Level gauge for the turntable
alignment
17. Clearaudio
Stroboscope Testrecord
(Art. No. AC038) to adjust the exact speed
12. 1 pcs. at belt 18. Optional in package:
Turntable + tonearm + cartridge No illustration:
Cartridge alignment gauge
for
Unify
or
Universal
tonearm (optional)
13. 4 pcs. hex wrench; sizes: #1,5; # 2,5; #3; #7
19. Not shown: warranty card, Clearaudio Quality
Card, Sales return paper
14. Screw driver 17. Not shown: User Manual
Pic. 2.1: List of components
IMPORTANT NOTICE:
Please double check the tightness of all bolts, hardware, and mounting pods, as temperature uctuations during transit may have caused the hardware to become loose.
16 b
Innovation
User manual
Page 7
Page 7© Clearaudio electronic GmbH 2016
3. Installation and setup
The setup of the
Innovation
turntable is easy as the turntable chassis is pre-assembled and has been tested at the factory. Please use the white gloves enclosed in order to avoid scratches or unwanted ngerprints (platter).
The
Innovation
turntable requires a space for setup of at least 18.90 inch x 19.29 inch.
18.90 inch / 480 mm
19.29 inch / 490 mm
Pic. 3: Required set - up space
Innovation
User manual
Page 8
Page 8 © Clearaudio electronic GmbH 2016
Please follow the description step by step:
1.)
First take out the three black at pads out of the accessory bag. Place these at pads on your hi-rack or another suitable base, where the nal position of your
Innovation
turntable will be.
2.)
After that, take the Innovation turntable body of the next packing layer and place the spikes of the turntable on the at pads.
Pic. 4:
Innovation
with tonearm base
Pic. 6: Oiling the bearing shaft
3.)
To avoid hum noises it can be necessary to ground the bearing. For that please plug in the provided ground cable into the hole of the screw from the bearing at the bottom side of the turntable.
Pic. 5: Grounding the bearing of the
Innovation
4.)
Remove the protective security tape from the bearing housing. Place two drops of the synthetic bearing oil on the ceramic bearing shaft. (also available at www.analogshop.de, Art. No. AC068)
Innovation
User manual
Page 9
Page 9
© Clearaudio electronic GmbH 2016
5.)
Take the stainless steel platter with both hands carefully out of the box. Remove the lamination of the scale ring on the lower side of the turntable.
Please remove the lamination extreme carefully and avoid any soiling and scratches.
Push the delivered bearing part carefully through the hole in the stainless steel sub-platter and mount the bearing part with the sub-platter by using the mounting clip.
6.)
In the next step remove the lamination of the sensor, mounted on the turntable chassis (picture 6: red
frame).
Please remove the lamination extreme carefully and avoid any soiling and scratches.
Pic. 7: Connection sub-platter and bearing upper part
Pic. 8: Removing the lamination
7.)
With both hands you can place the stainless steel platter carefully onto the bearing. Through a lightly (!!) up and down movement the platter will slip onto the bearing upper part (picture 8).
Make sure with gentle pressure that the platter is applying on the complete surface of the bearing.
Avoid major side forces to avoid any damages to the ceramic bearing!
Pic. 9: Setup stainless steel platter with
upper bearing part
Innovation
User manual
Page 10
Page 10 © Clearaudio electronic GmbH 2016
8.)
Now you can remove the mounting clip with the delivered hex wrench.
9.)
Take the Delrin platter with both hands out of the box and set the platter carefully onto the bearing.
The at side of the platter should face to the stainless steel platter and the side with the cut-out (for the record) should
face up.
To avoid any damages on your bearing, the Delrin platter should have room temperature before the setup begins (approx. 20 ° Celsius).
Avoid major side forces to avoid any damages to the
ceramic bearing!
Pic. 10: Removing of the mounting clip
Pic. 11: Setup Delrin platter and bearing cap
You will nd suitable adjustment equipment under www.clearaudio.de or www.analogshop.de.
10.)
To install the tonearm, please follow the user manual of the manufacturer.
Innovation
User manual
Page 11
Page 11
© Clearaudio electronic GmbH 2016
11.)
To mount and adjust a cartridge, please follow the user manual of the manufacturer.
If you purchased your Clearaudio
Innovation
turntable as a package with tonearm and cartridge, you will
nd a
Smart Level Gauge
in your accessory, which will help you to adjust the Tracking Force of the
cartridge:
Pic. 12: Use of Smart Stylus Gauge
Innovation
User manual
tracking force too high! /
Auagekraft zu hoch!
tracking force too low! /
Auagekraft zu niedrig!
Diese Position der Nadel entspricht
einer Auagekraft von 20 mN (2,0g).
This position of the diamond correlates
to a tracking force of 20 mN (2.0g).
Page 12
Page 12 © Clearaudio electronic GmbH 2016
12.)
The following nal adjustment is very important:
Please ensure that your turntable rack is in a levelled position.
Please check with the bubble level gauge, if your
Innovation
turntable is in a levelled position. You can adjust each of the turntables feet to get the turntable levelled. Only if the turntable is in a levelled position you will get the best results with your
Innovation
turntable.
Pic. 13 a: Alignment of the
turntable
Pic. 13 b: Adjustment of the turntables`feets
13.)
Please connect the mains plug to your power supply.
14.)
Place the at belt around the platter and around the motor pulley.
By pushing the sensor-switch, marked with “33 1/3” on the motor, the turntable starts to spin until 33 1/3 rpm is reached.
After the initial setup we recommend to let the turntable spin for at least 15 to 30 minutes. This ensures a smoother break in.
Pic. 14: Connection power supply and motor
Innovation
User manual
Page 13
4. Fine adjustment of the
Innovation
motor
1.)
The motor adjustment is already pre set at the factory. Through the transport or through soiling on the sensor or the sensor ring some small speed deviations can occur. Please check the speed before using the turntable for the rst time.
For the correct adjustment of the speed please put the recommended Clearaudio
Stroboscope
Testrecord
on the platter. Follow hereby the instruction of the
Stroboscope Testrecord
user manual.
To check the speed with highest accuracy please use the Clearaudio
Speed Light
(Art. No. AC039, www.analogshop.de).
On the front side of your turntable there are three setting trimmers (see Pic. 15).
- Left trimmer = setting 33 1/3 rpm
(near turntable motor)
- Middle trimmer = setting 45 rpm
- Right trimmer = setting 78 rpm
(near turntable bearing)
Pic. 15: Fine adjustment of the motor (on the backside)
If you like to adjust the speed 33 1/3 rpm, take the Aluminum screw driver (see accessories) and turn the left trimmer until you have reached the right speed according to the Stroboscope Testrecord (see user manual “Stroboscope Testrecord”).
- Turning the trimmer counter clockwise = reduces the turntable speed
- Turning the trimmer clockwise = raises the turntable speed
Please proceed with the speed adjustment for 45 rpm and 78 rpm in the same way!
Please note:
If the turntable does not reach the correct speed, the sensor or the scale ring could be dirty or dusty. To clean the sensor, please take off the platter very carefully! Clean the sensor and the scale ring with a little isopropyl alcohol and a cotton bud. Be careful and avoid any scratches on the sensor or the scale ring!
If the motor has further more speed variations please contact your nearest authorized Clearaudio dealer or directly the Clearaudio factory (address on page 14).
If the turntable is not in use, disconnect the unit completely from the power supply by removing the main plug from the socket.
Now you are nally ready to play your vinyl records.
We wish you a lot of pleasure with your new
Innovation
turntable.
Page 13© Clearaudio electronic GmbH 2016
Innovation
User manual
Page 14
5. Special instruction
5.1 Maintenance
• If the
Innovation
turntable is a longer time not in use, please disconnect the motor from the main
supply.
• Every two years you can lubricate the bearing of the turntable platter with the delivered oil. In this case it is enough to put 1 or 2 drops of the oil into bearing.
• Please take special caution to any damages of the power cord. Any damages should be repaired only by authorized personal. A damaged power cord must be exchanged immediately!
Caution:
Please use only non alcoholic uids and only uids specially used for acrylic, to clean the
Innovation turntable.
Otherwise damage on the material or the surface can occur!
Don’t use try cloths for cleaning because of the electrostatic charging. Suitable cleaning uids
will be available at Clearaudio (www.analogshop.de) or your Hi dealer.
5.2 Transport
Send / ship the
Innovation
turntable always and only in the original packing!!!
Only in the original packing Clearaudio can provide the warranty. If you repackage the turntable, please make all steps inverted like at installation and setup (chapter 3).
• If any transportation of the
Innovation
turntable should be necessary, please always remove the
turntable platter and the shaft holder. Otherwise serious damage can occur!
• To avoid any dust coming into the bearing, the bearing hole needs to be covered as well. Only if the product is returned in its original packing Clearaudio can provide the warranty.
5.3 Service
In case of any necessary, service for all Clearaudio products should be done by authorized personal only. In case of any repair, the Clearaudio
Innovation
turntable needs to be send to your nearest authorized
Clearaudio distributor, dealer or directly to the Clearaudio factory.
Clearaudio electronic GmbH
Spardorfer Str. 150
91054 Erlangen
Germany
Phone: +49 9131 40300 100
Fax: +49 9131 40300 119
www.clearaudio.de
www.analogshop.de
info@clearaudio.de
Page 14 © Clearaudio electronic GmbH 2016
Innovation
User manual
Page 15
Clearaudio electronic is not responsible for typographical errors in descriptions. Technical specications subject to change or improvement without prior notice. Availability as long as stock lasts. Copies and imprints- also only in extracts – require written conformation through Clearaudio electronic GmbH; Germany
© Clearaudio electronic GmbH 2016
6. Technical data
Construction principle: Resonance optimised chassis’s shape, belt driven with optical,
full automatic speed control
Speed possibilities: 33 1/3 rpm / 45 rpm / 78 rpm Drive unit: Decoupled DC motor in a massive metal-housing. Bearing: Inverted and polished ceramic bearing shaft, polished sinter
bronze insert, including patented CMB bearing technology
Platter: VA stainless steel sub-platter, Delrin or acrylic GS-PMMA platter,
precision CNC machined surface
Speed variation less than: +/- 0.05 % Deviance of the set value: +/- 0.01 % Weight: approx. 25 kg (without tonearm and power supply) Dimensions (w x d x h): approx. 428 mm x 390 mm x 208 mm
(16.85 inch x 15.35 inch x 8.19 inch)
Power consumption:
Max. consumption: Consumption in operation: Stand by mode: Off mode:
9.3 Watt
2.5 Watt
2.5 Watt
0.0 Watt
Warranty:
5 years* (see page 16)
* Only if the warranty card is lled out correctly and sent back to Clearaudio within 14 days.
Version: October 2016
Page 15© Clearaudio electronic GmbH 2016
Innovation
User manual
Page 16
To achieve the full Clearaudio warranty (Innovation turntable 5 years), it is necessary that you ll out and send the corresponding part of the warranty registration certicate /card back to Clearaudio, within two weeks after purchase. Only if the product is returned in its original packing Clearaudio can provide the warranty of 5 years.
ENGLISH WARRANTY
For warranty information, contact your local clearaudio distributor.
RETAIN YOUR PURCHASE RECEIPT
Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with clearaudio.
IMPORTANT
When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. Your purchase receipt or invoice is adequate for such proof. FOR U.K. ONLY This undertaking is in addition to a consumer‘s statutory rights and does not affect those rights in any way.
FRANÇAIS GARANTIE
Pour des informations sur la garantie, contacter le distributeur local clearaudio.
CONSERVER L‘ATTESTATION D‘ACHAT
L‘attestation d‘achat est la preuve permanente d‘un achat de valeur. La conserver en lieu sur pour s‘y reporter aux ns d‘obtention d‘une couverture d‘assurance ou dans le cadre de correspondances avec clearaudio.
IMPORTANT
Pour l‘obtention d‘un service couvert par la garantie, il incombe au client d‘établir la preuve de l‘achat et d‘en corroborer la date. Le reçu ou la facture constituent des preuves sufsantes.
DEUTSCH GARANTIE
Bei Garantiefragen wenden Sie sich bitte zunächst an Ihren clearaudio-Händler. Heben Sie Ihren Kaufbeleg gut auf.
WICHTIG!
Die Angaben auf Ihrer Quittung erlauben uns die Identizierung Ihres Gerätes und belegen mit dem Kaufdatum die Dauer Ihrer Garantie-Ansprü­che. Für Serviceleistungen benötigen wir stets die Gerätenummer. Diese nden Sie auf dem Typenschild auf der RückPage des Gerätes oder auf dem Tonarm sowie in der beigefügten Garantie-Registrierkarte.
NEDERLANDS GARANTIE
Voor inlichtingen omtrent garantie dient u zich tot uw plaatselijke clearaudio.
UW KWITANTIE, KASSABON E.D. BEWAREN
Uw kwitantie, kassabon e.d. vormen uw bewijs van aankoop van een waardevol artikel en dienen op een veilige plaats bewaard te worden voor evt, verwijzing bijv, in verbend met verzekering of bij correspondentie met clearaudio.
BELANGRIJK
Bij een evt, beroep op de garantie is het de verantwoordelijkheid van de consument een gedateerd bewijs van aankoop te tonen. Uw kassabon of factuurzijn voldoende bewijs.
ITALIANO GARANZIA
L’apparecchio è coperto da una garanzia di buon funzionamento della durata di un anno, o del periodo previsto dalla legge, a partire dalla data di acquisto comprovata da un documento attestante il nominativo del Rivenditore e la data di vendita. La garanzia sarà prestata con la sostituzione o la riparazione gratuita delle parti difettose. Non sono coperti da garanzia difetti derivanti da uso improprio, errata installazione, manutenzione effettuata da personale non autorizzato o, co­munque, da circostanze che non possano riferirsi a difetti di funzionamento dell’apparecchio. Sono inoltre esclusi dalla garanzia gli interventi inerenti l’installazione e l’allacciamento agli impianti di alimentazione. Gli apparecchi verranno riparati presso i nostri Centri di Assistenza Autorizzati. Le spese ed i rischi di trasporto sono a carico del cliente. La casa costruttrice declina ogni responsabilità per danni diretti o indiretti provocati dalla inosservanza delle prescrizioni di installazione, uso e manutenzione dettagliate nel presente manuale o per guasti dovuti ad uso continuato a ni professionali.
ESPAÑOL GARANTIA
Para obtener información acerca de la garantia póngase en contacto con su distribuidor clearaudio.
GUARDE SU RECIBO DE COMPRA
Su recibo de compra es su prueba permanente de haber adquirido un aparato de valor, Este recibo deberá guardarlo en un lugar seguro y utilizarlo como referencia cuando tenga que hacer uso del seguro o se ponga en contacto con clearaudio.
IMPORTANTE
Cuando solicite el servicio otorgado por la garantia el usuario tiene la responsabilidad de demonstrar cuándo efectuó la compra. En este caso, su recibo de compra será la prueba apropiada.
Innovation
User manual
Page 16 © Clearaudio electronic GmbH 2016
Page 17
Stroboscope Testrecord
User manual
Innovation
User manual
The Clearaudio
Stroboscope Testrecord
satises the highest demands for an exact speed adjustment for
turntables. Dramatic sound improvements can be reached only with exact calibrated speeds.
- Optimal adjustment for turntables -
To adjust the exact speed, please choose the side for 50 / 60 Hz, or the other side for the use with the speed light rst. If you choose the side without the speed light source, you can use the regular light source for the installation, either 50 Hz (outer scales) or 60 Hz. The scales are graduated in three different reading options:
33.3 Hz, 45 Hz and 78 Hz (starting from the outer diameter).
Please place the
Stroboscope Testrecord
on your turntable platter and start
the engine of your turntable. The big advantage of the Clearaudio
Stroboscope Testrecord
is, that you can place your cartridge onto the
Stroboscope Testrecord
, while measuring the speed, as there are grooves provided on the disc. This means, for the rst time a real time speed analysis is possible under realistic circumstances.
If you have the impression that the horizontal lines move on the scale, you should set or readjust the speed of the motor again.
- If the lines move clockwise, the speed is too fast.
- If the lines move counter clockwise, the motor speed is too slow.
Please correct the speed on your motor or turntable until you have the impression that the lines stopped moving. After that you have reached the exact speed and you can enjoy the full potential of your vinyl collection again.
Page 17© Clearaudio electronic GmbH 2016
Page 18
Page 18 © Clearaudio electronic GmbH 2016
Innovation
User manual
If you use the
Speed Light
(Art. No. AC039) you can reach an even higher or more accurate adjustment, completely independent of the power line or frequency of your country. As well, the 300 Hz calibrated light, used as an external light source is completely independent from possible power line uctuations, which could inuence the result by regular light. The 300 Hz of the
Speed Light
are generated by a
stabilized quartz oscillator and permit a very exact adjustment. Please put the
Stroboscope Testrecord
with the ne lines upward on your turntable. Here you also
have the possibility to choose between two different speeds.
With the outside scale you can detect the speed of 33 Hz and with the inside scale you can detect the
speed of 45 Hz. Again, the big advantage of the Clearaudio
Stroboscope Testrecord
is, that you can place
your cartridge onto the
Stroboscope Testrecord
, while measuring the speed, as there are grooves provided on the disc. This means, for the rst time a real time speed analysis is possible under realistic circumstances.
Press the button of the speed light source and place it parallel over to the scale and adjust the motor or turntable speed until the horizontal lines do not move anymore.
- Tip -
As more accurate your turntable speed is adjusted, as better the overall sonic appearance of the record playback will be! It is mandatory to check the speed several times through out the year, to ensure that other inuences are not minimizing the sound quality.
Technical Data:
Speed Light
Light source: blue LED / 300 Hz precision light source (calibrated)
Battery: V23GA – 12 V – Alkaline (Art. No.: AC039/B)
(Technical changes are subject without notication)
Date: 10/2016
Clearaudio electronic GmbH
Spardorfer Str. 150
91054 Erlangen
Germany
Phone: +49 9131 40300 100
Fax: +49 9131 40300 119
www.clearaudio.de
www.analogshop.de
info@clearaudio.de
Loading...