Claypaky AXCOR PROFILE 600, AXCOR PROFILE 600 HC Instruction Manual

Page 1

INSTRUCTION MANUAL

Congratulations on choosing a Claypaky product! We thank you for your custom. Please note that this product, as all the others in the rich Claypaky range, has been designed and made with total quality to ensure excellent performance and best meet your expectations and requirements.

INDEX

ENGLISH

Page Contents

2 1. Safety information 3 2. Unpacking and preparation 4 3. Installation and start-up

4 3.1 Installing the fixture 4 3.2 Connecting to manis supply 5 3.3 Connecting the control signal line: DMX / Art-Net 5 3.4 Switching on the fixture and basic SetUp

7 4. Maintenance 7 4.1 Opening the covers 8 4.2 Periodical cleaning

9 4.3 Effects module removal 14 4.4 Cleaning of the filters 16 4.5 Rotating gobos 17 4.6 Battery removal

18 5. Specifications

AXCOR PROFILE 600

AXCOR PROFILE 600 HC

C61705

C61706

Page 2

AXCOR PROFILE 600 - 600 HC

SAFETY INFORMATION

IMPORTANT: Claypaky recommends you carefully read and keep the safety information on this product, also available in digital format at the following link:

www.claypaky.com

Ref: FIS00W - Safety Information Axcor 600 series

INFORMAZIONI DI SICUREZZA

IMPORTANTE: Claypaky raccomanda di leggere accuratamente e conservare le informazioni di sicurezza relative a questo prodotto, sempre reperibili in versione digitale al seguente link:

www.claypaky.com

Rif: FIS00W - Safety Information Axcor 600 series

NFORMATIONEN ZUR SICHERHEIT

WICHTIG: Claypaky empfiehlt, die Sicherheitsinformationen bezüglich dieses Produkts genau zu lesen und aufzubewahren. Sie sind in Digitalversion immer unter folgendem Link auffindbar:

www.claypaky.com

Ref: FIS00W - Safety Information Axcor 600 series

INFORMACIONES DE SEGURIDAD

IMPORTANTE: Claypaky recomienda leer detenidamente y conservar la información de seguridad relativa a este producto. Además, está disponible una versión digital de la misma en el siguiente enlace:

www.claypaky.com

Ref: FIS00W - Safety Information Axcor 600 series

CONSIGNES DE SÉCURITÉ

IMPORTANT: Claypaky recommande de lire attentivement et de conserver les informations de sécurité relatives à ce produit, disponibles en version digitale au lien suivant:

www.claypaky.com

Réf. : FIS00W - Safety Information Axcor 600 series

ИНСТРУКЦИЮ ПО ТЕХНИКЕ БЕЗОПАСНОСТИ

ВАЖНО: Claypaky рекомендует внимательно прочитать и сохранить инструкцию по технике безопасности данного изделия, которая всегда доступна в электронном формате по следующей ссылке:

www.claypaky.com

Наименование: FIS00W - Safety Information Axcor 600 series

1. SAFETY INFORMATION

Page 3

AXCOR PROFILE 600 - 600 HC

PAN Mechanism Lock and Release (every 90°) - Fig. 2

TILT Mechanism Lock and Release (every 45°) - Fig. 3

Packing contents - Fig. 1

UNLOCKED

LOCKED

2 x 183102/805

2. UNPACKING AND PREPARATION

2 3

Page 4

AXCOR PROFILE 600 - 600 HC

3. INSTALLATION AND START-UP

Connecting and disconnecting power cable - Fig. 5

Installing the projector - Fig. 4

The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.

WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/001 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.

.1 Installing the fixture

3.2 Connecting to manis supply

Page 5

AXCOR PROFILE 600 - 600 HC

Switching on the projector - Fig. 8 Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:

Model Firmware xxx (Fixture ID) System errors

Axcor Version X.X.X Dmx Address xxx E: .........................

600 Date - Hour W: .........................

On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 128 bit - Tilt 128 bit). The control panel (Fig. 8) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions: rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set). During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status. It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the

key will be cancelled.

Dmx Address

Warning Message

Fixture ID

Connecting to the control signal line (DMX) - Fig. 7 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5 pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3. IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.

Connecting to the mains supply - Fig. 6

SIGNAL

CREEN

DMX 512

5 PIN

SIGNAL

SCREEN

MX 512 3 PIN

SIGNAL

Mains

Continue

➔

3.3 Connecting the control signal line: DMX / Art-Net

3.4 Switching on the fixture and basic SetUp

Page 6

AXCOR PROFILE 600 - 600 HC

Reversal of the display - Fig. 9 To activate this function, press UP

and DOWN Ckeys simultaneously while the display is in the rest mode. This status will be memorised and

maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.

etting the projector starting address

On each projector, the starting address must be set for the control signal (addresses from 1 to 512). The address can also be set with the projector switched off.

Setting the projector Fixture ID

On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255). The Fixture ID address can be set with the projector switched off.

Functions of the buttons - Using the menu

Setting addresses and options with the projector disconnected

The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply. All that is needed is to press

to momentarily activate the display and thus access the settings. Once the required operations have been carried out,

the display will switch off again after a wait time of 30 seconds.

USING THE MENU:

1) Press

once – “Main Menu” appears on the display.

2) Use the UP

and DOWN Ckeys to select the menu to be used:

• Setup (Setup Menu): To set the setting options.

• Option (Option Menu): To set the operating options

• Informations (Informations Menu): To read the counters, software version and other information.

• Manual Control (Manual control Menu): To trigger the test and manual control functions.

• Test (Test Menu): To check the proper functionning of effects

• Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel.

3) Press

to display the first item in the selected menu.

4) Use the UP

and DOWN Ckeys to select the MENU items.

Confirms the displayed value, or activates the displayed function, or enters the successive menu.

Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.

Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.

Return to the top level

Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù.

DOWN

LEFT

RIGHT

Page 7

AXCOR PROFILE 600 - 600 HC

Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section. Opening the head covers - Fig. 10.

Closing the head covers - Fig. 11.

1/4 Turn

CLICK!!

1/4 Turn

/4 Turn

10 11

Continue

➔

4. MAINTENANCE

.1 Opening the covers

Page 8

Lower side

pper side

AXCOR PROFILE 600 - 600 HC

Periodical cleaning - Fig. 12 To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.). Use a soft cloth dampened with any detergent liquid for cleaning glass to remove the dirt from the reflectors, from the lenses and filters. It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:

• General cleaning of internal parts.

• Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky.

• General visual check of the internal components, cabling, mechanical parts, etc.

• Electrical, photometric and functional checks; eventual repairs.

NOTE: keep a careful cleaning o

f the ''CMY/colour filters assembly''

to prevent rapid deterioration.

Light collimation system

This product contains internal light collimation system. Avoid intense light from any angle.

.2 Periodical cleaning

Page 9

AXCOR PROFILE 600 - 600 HC

Upper side

Lower side

Extraction of the effect modules: Preliminary operations - Fig. 13.

NOTE:

- Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards.

- Do not switch-on the fixtures with wiring harness disconnected.

Continue

➔

.3 Effects module removal

Page 10

AXCOR PROFILE 600 - 600 HC

Lower side

Upper side

Extraction of the effect modules: Preliminary operations - Fig. 14.

NOTE:

- Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards.

- Do not switch-on the fixtures with wiring harness disconnected.

Page 11

AXCOR PROFILE 600 - 600 HC

Upper side

Extraction of the effect modules - Fig. 15. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 15, 16, 17 and 18 in reverse order.

Continue

➔

Page 12

AXCOR PROFILE 600 - 600 HC

Upper side

Extraction of the effect modules - Fig. 16. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 15, 16, 17 and 18 in reverse order.

Page 13

AXCOR PROFILE 600 - 600 HC

Lower side

Extraction of the effect modules - Fig. 17. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 15, 16, 17 and 18 in reverse order.

Continue

➔

Page 14

AXCOR PROFILE 600 - 600 HC

Cleaning of the filters - Fig. 18.

1/4 Turn

.4 - Cleaning of the filters

Page 15

AXCOR PROFILE 600 - 600 HC

1/4 Turn

Cleaning of the filters - Fig. 19.

Continue

➔

Page 16

AXCOR PROFILE 600 - 600 HC

INDEX

GOD019/013

GOD019/014

GOD019/010

GOD019/009

GOD019/008

GOD019/012GOD019/011

25 ±0.1

1 ±0.1

ø25.9 ±0.1

Immagine ø20

Replacing rotating gobos (max 20 mm image – thickness 1 mm) - Fig. 21

- Before use custom gobos contact Claypaky;

- The original gobos have a special coating designed specifically to resist to the high temperatures;

- The rotating gobo wheel only use dichroic glass gobos (it is not possible to use metal gobos);

- For more information contact Claypaky;

Bearing group replacement - Fig. 20

.5 - Rotating gobos

Page 17

AXCOR PROFILE 600 - 600 HC

This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.

.6 Battery removal

Page 18

AXCOR PROFILE 600 - 600 HC

329

(12.95")

388

(15.28")

636

(25.04")

570

(22.44")

785

(30.91")

409

(16.10")

607

(23.90")

POWER SUPPLIES

AC power input Neutrik PowerCON True 100-240V, 50/60 Hz

INPUT POWER

800 VA @230Vac - 50Hz

LIGHT SOURCE

• Source: 500W White LED Engine

• Versions available:

- CRI: at least 70, CT 6500K (Axcor Profile 600)

- CRI: at least 90, CT 5600K (Axcor Profile 600 HC)

MOTORS

Stepper motors, operating with micro-steps, totally microprocessor controlled

CHANNELS

40/44 control channels

INPUTS

DMX 512 – Art-Net

NOISE LEVEL

45 dBA (background 33 dBA)

IP RATING

IP 20 - Protected against the entry of solid bodies larger than 12mm (0.47”); No protection against the entry of liquids.

SAFETY SPECIFICATIONS

Minimum distance of illuminated objects 3 meters (9’ 10”) Minimum distance from flammable materials 0.2 meters (8”) Max ambient temperature 40°C (104°F) Max temperature of the external surface 90°C (194°F) Safety devices Bipolar circuit breaker with thermal protection Automatic break in power supply in case of overheating Forced ventilation with axial fans

ELECTRONICS

Long life self-charging buffer battery Function reset from the lighting desk “AUTOTEST” function from menu Electronic monitoring with status error Cooling system monitoring DMX level monitoring on all channels Internal data transmission diagnostics Firmware Upgrade via Web Server Firmware upload from another fixture Protocols/Functions: RDM, Web Server

OPTICS

Ø 132mm front lens

5.3°- 47.2° linear Zoom

EFFECTS SECTION

Rotating Gobo wheel : 7 interchangeable gobos

Animation wheel (interchangeable with fixed gobo wheel) Rotating Prism: 1 x 4-facet prism, indexable on 540°; clockwise and counterclockwise rotation at variable speed Variable frost 0-100% linear Color system CMY with gradually insertion Linear CTO Color wheel 5 colors Iris with multiple macros (random, pulsing…) Dimmer 16 bit electronic and linear; 3 dimmer curves Strobe 25 flash/sec, electronic, instant open and blackout Framing System 4 focal planes 4 Blades that move separately Smooth, flexible blade movements at variable speed 90° rotation of the entire system, at variable speed

CONTROL AND PROGRAMMING

DMX 512 control channels Control signal USITT DMX 512 Protocols RDM, WebServer and Art-Net Display Graphic LCD backlit b/w Display Display battery Long life self-charging buffer battery Pan/Tilt Resolution 16 bit Focus Resolution 16 bit Gobo Resolution 16 bit Dimmer Resolution 16 bit Movement control vectorial DMX signal connection 3 or 5 pole XLR input and output Ethernet Input Firmware update Software upload through DMX/Ethernet input

BODY

Aluminum and steel structure with plastic covers Two side handles for transportation Device locking PAN and TILT mechanisms for transportation and maintenance

MOVING BODY

PAN range 540° TILT range 268°

WORKING POSITION

Working in any position Hanging system: with fast-lock omega clamps (1/4 turn) on the base

CE MARKING

In conformity with the European Directives:

• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD)

• 2014/30/EU - Electromagnetic Compatibility (EMC)

• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)

• 2009/125/EC - EcoDesign requirements for Energy-related Products (ErP)

WEIGHT

33 Kg (72.7 lbs)

5. SPECIFICATIONS

Page 19

Page 20

Clay Paky S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035 -654311 - Fax +39-035-301876 - www.claypaky.com

IST01A/001 – EN - PRELIMINARY 09/2018