Clay Paky ALPHA SPOT HPE 1500 ST User Manual

ALPHA SPOT HPE 1500

ENGLISH

ALPHA SPOT HPE 1500 ST

C61325

C61326

INSTRUCTION MANUAL

INDEX

Page Contents

2 Safety Information
4 Informazioni di sicurezza
6 Consignes de sécurité
8 Informationen zur Sicherheit

10 Informaciones de suguridad

12 Unpacking and preparation

13 Installation and start-up

14 Control panel

16 Menu setting

25 Maintenance

34 Technical information

34 Cause and solution of problems

35 Channel functions

EN

IT

FR

ES

DE

Congratulations on choosing a Clay Paky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Clay
Paky range, has been designed and made with total quality to
ensure excellent performance and best meet your expectations
and requirements.

Carefully read this instruction manual in its entirety and keep it
safe for future reference. It is essential to know the information
and comply with the instructions given in this manual to ensure
the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting
or to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this
instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the
characteristics stated in this instruction manual at any time and
without prior notice.

1

1500W

5

ta40°C

IP20

EN

• Installation

Make sure all parts for fixing the projector are in a good state of repair.
Make sure the point of anchorage is stable before positioning the projector.
The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary
support system fails, the fitting falls as little as possible.
If the safety chain gets used, it needs to be replaced with a genuine spare.

• Minimum distance of illuminated objects

The projector needs to be positioned so that the objects hit by the beam of light are at least 5 metres (16'5'') from
the lens of the projector.

• Minimum distance from flammable materials

The projector must be positioned so that any flammable materials are at least 0.20 metres (8”) from every point on
the surface of the fitting.

• Maximum ambient temperature

Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

• IP20 protection rating

The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first digit 2), but not
against dripping water, rain, splashes or jets of water (second digit 0).

SAFETY INFORMATION

tc150°C

• Protection against electrical shock

Connection must be made to a power supply system fitted with efficient earthing (Class I appliance according to
standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the projectors from indirect
contact and/or shorting to earth by using appropriately sized residual current devices.

• Connection to mains supply

Connection to the electricity mains must be carried out by a qualified electrical installer.
Check that the mains frequency and voltage correspond to those for which the projector is designed as given on the
electrical data label.
This label also gives the input power to which you need to refer to evaluate the maximum number of fittings to
connect to the electricity line, in order to avoid overloading.
IMPORTANT: to prevent EMI disturbances, in some condition it might be necessary to clip around the DMX and the
Ethernet cable, as close as possible to the projector, an appropriate ferrite bead. Shielded cables must always be used.

• Temperature of the external surface

The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is
150°C (302°F).

• Maintenance

Before starting any maintenance work or cleaning the projector, cut off power from the mains supply.
After switching off, do not remove any parts of the fitting for at least 10 minutes. After this time the likelihood of the
lamp exploding is virtually nill. If it is necessary to replace the lamp, wait for another 20 minutes to avoid getting
burnt.
The fitting is designed to hold in any splinters produced by a lamp exploding. The lenses must be mounted and, if
visibly damaged, they have to be replaced with genuine spares.

Risk Group 2

According to

EN 62471

ALPHA SPOT HPE 1500 & ST

• Lamp

The fitting mounts a high-pressure lamp that needs an external igniter. This igniter is fitted onto the apparatus.

- Carefully read the "operating instructions" provided by the lamp manufacturer.

- Immediately replace the lamp if damaged or deformed by heat.

• Photobiological Safety

CAUTION. Possibly hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be
harmful to the eyes.

This product is intended for the following areas of application:
studios, stages, theaters, exhibitions, trade fairs, events, theme parks, entertainment venues, architectural lighting
and similar.

2

LiFePO4

b

P

Not suitable for household illumination

Not for residential use

• Battery

This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment,
please dispose the battery at the end of its life according to the regulation in force.

• Disposing

This product is supplied in compliance with European Directive 2012/19/EU - Waste Electrical and Electronic
Equipment (WEEE). To preserve the environment please dispose/recycle this product at the end of its life according
to the local regulation.

The products to which this manual refers comply with the European Directives pursuant to:

• 2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)

• 2004/108/EC - Electromagnetic Compatibility (EMC)

• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)

• 2009/125/EC - EcoDesign requirements for Energy-related Products (ErP)

ALPHA SPOT HPE 1500 & ST

3

1500W

5

ta40°C

IP20

IT

• Installazione

Assicurarsi che tutte le parti per il fissaggio del proiettore siano in buona condizione.
Assicurarsi della stabilità del punto di ancoraggio prima di posizionare il proiettore.
La fune di sicurezza, debitamente agganciata all’apparecchio e fissata alla struttura di sostegno, deve essere
installata in modo che, in caso di cedimento del sistema di supporto primario, si abbia la minor caduta possibile
dell’apparecchio. Dopo un eventuale intervento la fune di sicurezza deve essere sostituita con il ricambio originale.

• Distanza minima degli oggetti illuminati

Il proiettore deve essere posizionato in modo tale che gli oggetti colpiti dal fascio luminoso siano distanti almeno 5
metri dall’obiettivo del proiettore stesso.

• Distanza minima dei materiali infiammabili

Il proiettore deve essere posizionato in modo tale che i materiali infiammabili siano distanti almeno 0,20 metri da
ogni punto della superficie dell’apparecchio.

• Massima temperatura ambiente

Non utilizzare il proiettiore se la temperatura ambiente (Ta) supera i 40°C.

• Grado di protezione IP20

L’apparecchio è protetto contro la penetrazione di corpi solidi di dimensione superiore a 12mm (prima cifra 2),
mentre teme lo stillicidio, la pioggia, gli spruzzi e i getti d’acqua (seconda cifra 0).

INFORMAZIONI DI SICUREZZA

tc150°C

• Protezione contro la scossa elettrica

È obbligatorio effettuare il collegamento ad un impianto di alimentazione dotato di un’efficiente messa a terra
(apparecchio di Classe I secondo la norma EN 60598-1).
Si raccomanda, inoltre, di proteggere le linee di alimentazione dei proiettori dai contatti indiretti e/o cortocircuiti
verso massa tramite l’uso di interruttori differenziali opportunamente dimensionati.

• Collegamento alla rete di alimentazione

Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere effettuate da un
installatore elettrico qualificato. Verificare che frequenza e tensione della rete corrispondano alla frequenza ed alla
tensione per cui il proiettore è predisposto ed indicate sulla targhetta dei dati elettrici. Sulla medesima targhetta è
pure indicata la potenza assorbita. Fare riferimento a quest’ultima per valutare il numero massimo di apparecchi da
collegare alla linea elettrica, al fine di evitare sovraccarichi.
IMPORTANTE: per evitare l'insorgere di interferenze elettromagnetiche, in alcune situazioni può rendersi
necessario avvolgere attorno al cavo DMX ed al cavo Ethernet, il più possibile vicino al proiettore, una ferrite
appropriata. Usare sempre cavi schermati.

• Temperatura della superficie esterna

La temperatura massima raggiungibile sulla superficie esterna dell’apparecchio, in condizioni di regime termico, è
di 150°C.

• Manutenzione

Prima di iniziare qualsiasi operazione di manutenzione o pulizia sul proiettore togliere la tensione dalla rete di
alimentazione. Dopo lo spegnimento non rimuovere alcuna parte dell’apparecchio per 10 minuti. Trascorso tale
tempo la probabilità di esplosione della lampada è praticamente nulla. Se è necessario sostituire la lampada,
aspettare ulteriori 20 minuti per evitare scottature. L’apparecchio è progettato in modo da trattenere le schegge
prodotte dall’eventuale scoppio della lampada. Le lenti devono essere obbligatoriamente montate; devono inoltre,
se visibilmente danneggiate, essere sostituite con ricambi originali.

Gruppo di rischio 2

Secondo la norma

EN 62471

ALPHA SPOT HPE 1500 & ST

• Lampada

L’apparecchio monta una lampada ad alta pressione che richiede un accenditore esterno.
Tale accenditore è incorporato nell’apparecchio.

- Leggere attentamente le “istruzioni d’uso” fornite dal costruttore della lampada.

- Sostituire immediatamente la lampada se danneggiata o deformata dal calore.

• Sicurezza fotobiologica

ATTENZIONE: Possibile radiazione ottica rischiosa emessa da questo prodotto.
Non fissare la lampada in funzione. Può essere pericoloso per gli occhi.

4

LiFePO4

Pb

Il prodotto è concepito per essere utilizzato nei seguenti ambiti:
studi, palchi, teatri, esposizioni, fiere, eventi, parchi a tema, locali di intrattenimento, illuminazione architetturale e simili.

Non adatto all'illuminazione domestica

Non per uso residenziale

• Batteria

Questo prodotto contiene una batteria ricaricabile piombo-acido o Litio Ferro Tetrafosfato. A tutela dell'ambiente si
prega di smaltire la batteria a fine vita in conformità alla normativa vigente.

• Smaltimento

Questo dispositivo è conforme alla Direttiva Europea 2012/19/UE - Rifiuti di apparecchiature elettriche ed
elettroniche (RAEE). Nel rispetto dell'ambiente, smaltire/riciclare il prodotto al termine del suo ciclo di vita secondo
le disposizioni di legge locali.

I prodotti a cui questo manuale si riferisce sono conformi alle Direttive Europee di cui sono oggetto:

• 2006/95/CE - Sicurezza delle apparecchiature alimentate in Bassa Tensione (LVD)

• 2004/108/CE - Compatibilità Elettromagnetica (EMC)

• 2011/65/UE - Restrizione d’uso di determinate sostanze pericolose (RoHS)

• 2009/125/CE - Specifiche per la progettazione ecocompatibile dei prodotti connessi all’energia (ErP)

ALPHA SPOT HPE 1500 & ST

5

1500W

5

ta40°C

IP20

FR

• Installation

S’assurer que toutes les pièces pour la fixation du projecteur sont en bon état.
S’assurer de la stabilité du point d’ancrage avant de positionner le projecteur.
Le câble de sécurité, à fixer correctement à l’appareil et à la structure de support, doit être installé de façon à ce que,
en cas de rupture du système de support principal, la chute de l’appareil soit la plus limitée possible. Après une
éventuelle intervention du câble de sécurité suite à une chute, il faut le remplacer par une pièce de rechange d’origine.

• Distance minimum des objets éclairés

Le projecteur doit être positionné de façon à ce que les objets éclairés par le faisceau lumineux soient à une
distance d’au moins 5 mètres de l’objectif du projecteur.

• Distance minimum des substances inflammables

Le projecteur doit être positionné de façon à ce qu’il y ait une distance d’au moins 0,20 mètre entre toute substance
inflammable et tout point de sa surface.

• Température ambiante maximum

Ne pas utiliser le projecteur quand la température ambiante (Ta) dépasse 40°C.

• Degré de protection IP20

L’appareil est protégé contre la pénétration de corps solides de dimension supérieure à 12 mm (premier chiffre 2),
tandis qu’il craint les gouttes d’eau, la pluie et les projections d’eau (deuxième chiffre 0).

CONSIGNES DE SÉCURITÉ

tc150°C

• Protection contre l’électrisation

L’appareil doit obligatoirement être branché à une installation d’alimentation équipée d’une mise à la terre efficace
(appareil de Classe I selon la norme EN 60598-1).
Nous recommandons également de protéger les lignes d’alimentation des projecteurs contre les contacts indirects
et/ou les courts-circuits vers la masse en utilisant des interrupteurs différentiels de sensibilité adéquate.

• Branchement au réseau d’alimentation

Les opérations de branchement au réseau de distribution de l’énergie électrique doivent être exécutées par un
installateur électrique qualifié. Contrôler que la fréquence et la tension de réseau correspondent à la fréquence et
à la tension pour lesquelles le projecteur est prévu ; ces données sont indiquées sur la plaquette des données
électriques. Cette même plaquette reporte également la puissance absorbée. Afin d’éviter des surcharges, se
référer à celle-ci pour évaluer le nombre maximum d’appareils à brancher à la ligne électrique.
IMPORTANT : afin d’empêcher l’apparition de perturbations électromagnétiques, il peut s’avérer nécessaire dans
certains cas d'accrocher autour du DMX et du câble Ethernet, le plus près possible du projecteur, un manchon de
ferrite approprié. Toujours utiliser des câbles blindés.

• Température de la surface extérieure

La température maximum qui peut être atteinte sur la surface extérieure de l’appareil, en conditions de régime
thermique, est de 150°C.

• Entretien

Avant de procéder à toute opération d’entretien ou de nettoyage sur le projecteur, couper la tension d’alimentation.
Après avoir éteint le projecteur, ne démonter aucun élément de l’appareil pendant les 10 minutes qui suivent. Une
fois ce temps écoulé, la probabilité d’explosion de la lampe est quasiment nulle. S’il faut remplacer la lampe,
attendre encore 20 minutes afin d’éviter tout risque de brûlures.
L’appareil a été conçu de façon à retenir les éclats produits en cas d’explosion de la lampe. Les lentilles doivent
obligatoirement être montées sur l’appareil et doivent être remplacées par des pièces d’origine dès qu’elles sont
visiblement endommagées.

Classe de

dangerosité 2

Selon la norme

EN 62471

ALPHA SPOT HPE 1500 & ST

•

Lampe

L’appareil fonctionne avec une lampe haute pression avec ballast externe.
Ce dernier est incorporé dans l’appareil.

- Lire avec attention les « instructions d’utilisation » fournies par le fabricant de la lampe.

- Remplacer la lampe dès qu’elle est endommagée ou déformée par la chaleur

• Sécurité photobiologique

ATTENTION : Possible radiation optique émise par ce produit.
Ne pas fixer la lampe lorsqu’elle est allumée. Peut être dangereux pour les yeux.

6

LiFePO4

Pb

Le produit est conçu pour être utilisé dans les milieux suivants :
studios, scènes, théâtres, expositions, salons, événements, parcs à thème, lieux de divertissement, éclairage
architectural et similaires

Non adapté à l’éclairage domestique

Non indiqué pour un utilization résidentiel

• Batterie

Ce produit contient une batterie rechargeable au plomb-acide ou tétraphosphate de fer au lithium. Une fois la bat­terie arrivée à la fin de sa durée de vie, procéder à son élimination conformément à la no rme en vigueur de
manière à éviter toute pollution.

Élimination

Ce dispositif est conforme à la Directive Européenne 2012/19/UE – Déchets d’équipements électriques et
électroniques (DEEE). Dans le respect de l’environnement, écouler/recycler le produit à la fin de son cycle de vie
selon les dispositions légales locales.

The products to which this manual refers comply with the European Directives pursuant to:

• 2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)

• 2004/108/EC - Electromagnetic Compatibility (EMC)

• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)

• 2009/125/EC - EcoDesign requirements for Energy-related Products (ErP)

ALPHA SPOT HPE 1500 & ST

7

1500W

5

ta40°C

IP20

DE

• Installation

Sicherstellen, dass alle Teile für die Befestigung des Projektors in einwandfreiem Zustand sind.
Vor der Installation des Projektors die Stabilität der Verankerungsstelle überprüfen.
Das korrekt am Gerät eingehakte und an der Haltestruktur befestigte Sicherheitsseil muss so installiert werden,
dass bei einem Nachgeben der Haupthalterung die Fallhöhe des Gerätes so gering wie möglich ist. Nach einem
eventuellen Einsatz muss das Sicherheitsseil durch ein Originalersatzteil ersetzt werden.

• Mindestabstand zu beleuchteten Objekten

Der Projektor muss so installiert werden, dass der Abstand zwischen den vom Lichtstrahl beleuchteten Objekten
und dem Objektiv des Projektors mindestens 5 Meter beträgt.

• Mindestabstand zu entzündbaren Materialien

Der Projektor muss so installiert werden, dass entzündbare Materialien mindestens 0,20 Meter von jedem Punkt der
Geräteoberfläche entfernt sind.

• Max. Raumtemperatur

Den Projektor nicht verwenden, wenn die Raumtemperatur (RT) 40°C überschreitet.

• Schutzart IP20

Das Gerät ist gegen das Eindringen von festen Fremdkörpern mit Durchmesser über 12 mm (erste Kennziffer 2)
geschützt, während es gegen Tropf,- Regen- und Spritzwasser sowie Wasserstrahlen (zweite Kennziffer 0)
empfindlich ist.

INFORMATIONEN ZUR SICHERHEIT

tc150°C

• Schutz gegen Stromschlag

Es ist Pflicht, das Gerät an eine Stromversorgungsanlage anzuschließen, die mit einer leistungsfähigen Erdung
ausgestattet ist (Gerät der Klasse I gemäß Richtlinie EN 60598-1).
Darü b e r hina u s wird empfohlen, die Zuleitungen der Pr o j ektoren mit kor r e kt bem e s s enen
Fehlerstromschutzschaltern vor indirekten Kontakten und/oder Kurzschlüssen zu schützen.

• Netzanschluss

Der Anschluss an das Stromnetz muss von einem kompetenten Elektroinstallateur ausgeführt werden.
Vergewissern Sie sich, dass Spannung und Frequenz der Netzversorgung mit den Werten übereinstimmen, für die
der Projektor ausgelegt ist und die auf dem Typenschild angegeben sind. Ebenfalls auf dem Typenschild ist die
Leistungsaufnahme angegeben. Um zu beurteilen, wie viele Geräte maximal an die Stromleitung angeschlossen
werden können, ist auf diese Angaben Bezug zu nehmen, damit Überlastungen vermieden werden.
WICHTIG: Um das Auftreten von EMI-Störungen zu vermeiden, kann es in einigen Situationen notwendig werden,
möglichst nahe am Scheinwerfer um die DMX und das Ethernet-Kabel eine geeignete Ferritperle anzubringen.
Immer abgeschirmte Kabel verwenden.

• Temperatur der Außenfläche

Die Außenfläche des Geräts kann im Wärmebetrieb eine Höchsttemperatur von 150°C erreichen.

• Wartung

Vor Beginn von Wartungs- oder Reinigungsarbeiten am Projektor stets die Stromversorgung abschalten. Nach dem
Abschalten 10 Minuten lang keine Geräteteile abnehmen. Nach Ablauf dieser Zeit besteht praktisch keine Gefahr
mehr, dass die Lampe birst. Falls die Lampe ersetzt werden muss, weitere 20 Minuten warten, um
Verbrennungsgefahr zu vermeiden.
Das Gerät wurde so konzipiert, dass es die Splitter bei einem eventuellen Bersten der Lampe zurückhält. Die
Montage der Linsen ist obligatorisch vorgeschrieben; des Weiteren müssen sie bei sichtbarer Beschädigung durch
Originalersatzteile ersetzt werden.

Gefahrenklasse 2

Gemäß Norm

EN 62471

ALPHA SPOT HPE 1500 & ST

• Lampe

Das Gerät ist mit einer Hochdrucklampe bestückt, die eine externe Zündeinheit verlangt.
Diese Zündeinheit ist in das Gerät eingebaut.

- Lesen Sie die vom Lampenhersteller gelieferte "Bedienungsanleitung" aufmerksam durch.

- Eine beschädigte oder von der Hitze verformte Lampe muss sofort ersetzt werden.

• Photobiologische Sicherheit

ACHTUNG: Mögliche riskante optische Strahlung wird von diesem Produkt abgegeben.
Nicht die Lampe fixieren, wenn sie in Betrieb ist. Kann für die Augen gefährlich sein.

8

LiFePO4

Pb

Das Produkt wurde für die Verwendung in den folgenden Bereichen entwickelt:
Studios, Bühnen, Theater, Ausstellungen, Messen, Veranstaltungen, Themenparks, Unterhaltungslokale,
Architekturbeleuchtung oder ähnliches

Nicht für Haushaltsbeleuchtung geeignet

Nicht für den häuslichen Gebrauch

• Batterie

Dieses Produkt enthält eine wiederaufladbare Blei-Säure-Batterie oder Lithium-Eisen-tetraphosphat. Zum
Schutz der Umwelt bitten wir Sie, diese Batterie, nachdem sie verbraucht ist, gemäß den geltenden
Vorschriften zu entsorgen.

Entsorgung

Diese Vorrichtung entspricht der Europäischen Richtlinie 2012/19/UE - Abfall von elektrischen und elektronischen
Gerätschaften (RAEE). Das Produkt am Ende seines Lebenszyklus unter Berücksichtigung der Umwelt nach den
lokalen Gesetzesvorschriften entsorgen/recyceln.

The products to which this manual refers comply with the European Directives pursuant to:

• 2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)

• 2004/108/EC - Electromagnetic Compatibility (EMC)

• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)

• 2009/125/EC - EcoDesign requirements for Energy-related Products (ErP)

ALPHA SPOT HPE 1500 & ST

9

1500W

5

ta40°C

IP20

ES

• Instalación

Asegúrese de que todos los elementos de fijación del proyector estén en buenas condiciones.
Controle la estabilidad del punto de anclaje antes de instalar el proyector.
La cuerda de seguridad, correctamente enganchada al aparato y fijada a la estructura de soporte, debe colocarse
de modo que, si el soporte principal cede, el aparato sufra la menor caída posible. En caso de desgaste de la
cuerda de seguridad, sustitúyala por el recambio original.

• Distancia mínima de los objetos iluminados

El proyector debe ser posicionado de modo tal que los objetos tocados por el haz luminoso tengan una distancia
de al menos 5 metros del objetivo del mismo proyector.

• Distancia mínima de los materiales inflamables

El proyector debe ser posicionado de modo tal que los materiales inflamables tengan una distancia de al menos
0,20 metros de cada punto de la superficie del aparato.

• Máxima temperatura ambiente

No utilice el proyector si la temperatura ambiente (ta) supera los 40°C.

• Grado de protección IP20

El aparato está protegido contra la penetración de cuerpos sólidos de dimensiones superiores a 12 mm (primer
dígito 2), pero no contra el goteo, la lluvia, las salpicaduras y los chorros de agua (segundo dígito 0).

INFORMACIONES DE SEGURIDAD

tc150°C

• Protección contra descargas eléctricas

Es obligatorio efectuar la conexión a una instalación de alimentación dotada de una eficiente puesta a tierra
(aparato de Clase I según la norma EN 60598-1).
Además, se recomienda proteger las líneas de alimentación de los proyectores de los contactos indirectos y/o
cortocircuitos hacia masa, mediante el uso de interruptores diferenciales dimensionados oportunamente.

• Conexión a la red de alimentación

Las operaciones de conexión a la red de distribución de la energía eléctrica deben ser efectuadas por un instalador
eléctrico cualificado. Constate que los valores de frecuencia y tensión de la red sean iguales a los que figuran en la
placa de los datos eléctricos del proyector. En la misma placa está indicada la potencia absorbida. Hacer referencia a
esta última para valorar el número máximo de aparatos que conectar a la línea eléctrica, con el fin de evitar sobrecargas.
IMPORTANTE: para evitar que surjan interferencias electromagnéticas, en algunas situaciones puede ser
necesario enganchar alrededor de la DMX y al cable Ethernet, lo más cerca posible del proyector, un apropiado
manguito de ferrita. Usar siempre cables blindados.

• Temperatura de la superficie externa

La temperatura máxima que puede alcanzar la superficie externa del aparato, en condiciones de régimen térmico,
es de 150°C.

• Mantenimiento

Antes de iniciar cualquier operación de mantenimiento o limpieza del proyector desconecte el aparato de la
alimentación eléctrica. Después del apagado no extraiga ninguna parte del aparato durante 10 minutos. Transcurrido
dicho tiempo la probabilidad de que la lámpara explote es prácticamente nula. Si fuera necesario cambiar la lámpara,
espere 20 minutos más para evitar quemarse.
El aparato está proyectado para retener las astillas producidas por el posible estallido de la lámpara. Las lentes deben
montarse obligatoriamente; además, si estuvieran dañadas, deberán ser sustituidas por recambios originales.

Clase de

peligrosidad 2

Según la norma

EN 62471

ALPHA SPOT HPE 1500 & ST

• Lámpara

El aparato utiliza una lámpara de alta presión que requiere un arrancador externo.
Dicho arrancador está incorporado en el aparato.

- Leer atentamente las "instrucciones de uso" suministradas por el fabricante de la lámpara.

- Sustituir la lámpara inmediatamente si estuviera dañada o deformada por el calor.

• Seguridad fotobiológica

ATENCIÓN: Posible radiación óptica arriesgada emitida por este producto.
No fije la lámpara en funcionamiento. Puede ser peligroso para los ojos.

10

LiFePO4

Pb

El producto es concebido para ser utilizado en los siguientes ambientes:
estudios, palcos, teatros, exposiciones, ferias, eventos, parques temáticos locales de entretenimiento, iluminación
de arquitecturas y similares

No es apropiado para la iluminación doméstica

No para uso residencial

• Batería

Este producto contiene una batería recargable plomo-ácido o de litio tetrafosfato Hierro. Para proteger el ambiente
se ruega eliminar la batería conforme a la normativa vigente.

Eliminación

Este dispositivo es conforme a la Directiva Europea 2012/19/UE - Residuos de equipos eléctricos y electrónicos
(RAEE). Con el fin de respetar el ambiente, eliminar/reciclar el producto al final de su ciclo de vida según las
disposiciones de ley locales

The products to which this manual refers comply with the European Directives pursuant to:

• 2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)

• 2004/108/EC - Electromagnetic Compatibility (EMC)

• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)

• 2009/125/EC - EcoDesign requirements for Energy-related Products (ErP)

ALPHA SPOT HPE 1500 & ST

11

1

90°

9

0

°

9

0°

90

°

LOCKED

UNLOCKED

4

5°

4

5

°

4

5°

4

5

°

45°

4

5

°

UNLOCKED

LOCKED

IST00C/001

UNPACKING AND PREPARATION

2 x 183102/805

Lamp 1500W

(fitted into projector)

Packing contents - Fig. 1

2

3

PAN Mechanism Lock and Release (every 90°) - Fig. 2

TILT Mechanism Lock and Release (every 45°) - Fig. 3

ALPHA SPOT HPE 1500 & ST

12

4

1

2

1

2

3

INSTALLATION AND START-UP

Installing the projector - Fig. 4

The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.

WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request).
This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.

5

Connecting and disconnecting power cable - Fig. 5

ALPHA SPOT HPE 1500 & ST

13

CONTROL PANEL

1

2

Dmx Address

Warning Message

Fixture ID

MAINS

L

N

SIGNAL

SCREEN

DMX 512

5 PIN

1

2

3

4

5

SIGNAL

SCREEN

1

3

2

DMX 512

3 PIN

SIGNAL

SIGNAL

DMX 512

6

onnecting to the mains supply - Fig. 6

C

Mains

7

Connecting to the control signal line (DMX) - Fig. 7
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female
connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors.

8

Switching on the projector - Fig. 8
Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:

Model Firmware xxx (Fixture ID) System errors

Alpha SPOT HPE Version X.X.X Dmx Address xxx E: .........................

1500 Date - Hour W: .........................

On conclusion of resetting in case of absence of dmx signal, Pan and Tilt move to the “Home” position (Pan 50% - Tilt 50%). The control panel (Fig.

8) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions:
rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set).
During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the

ALPHA SPOT HPE 1500 & ST

14

key will be cancelled.

F

28

28

9

Reversal of the display - Fig. 9
To activate this function, press UP
maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.

Setting the projector starting address

On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
The address can also be set with the projector switched off.
Setting the address: see pag. 8.

Setting the projector Fixture ID

On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255).
The Fixture ID address can be set with the projector switched off.
Setting the Fixture ID: see pag. 8.

and DOWN Ckeys simultaneously while the display is in the rest mode. This status will be memorised and

B

Functions of the buttons - Using the menu

Confirms the displayed value, or activates the displayed function, or enters the successive

F

C

DOWN

B

D

LEFT

E

RIGHT

USING THE MENU:

1) Press

2) Use the UP

• Setup (Setup Menu): To set the setting options.

• Option (Option Menu): To set the operating options.

• Informations (Informations Menu): To read the counters, software version and other information.

• Manual Control (Manual control Menu): To trigger the test and manual control functions.

• Test (Test Menu): To check the proper functionning of effects.

• Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel.
To enable the "Advanced" see pag. 14

3) Press

4) Use the UP

once – “Main Menu” appears on the display.

F

and DOWN Ckeys to select the menu to be used:

B

to display the first item in the selected menu.

F

and DOWN Ckeys to select the MENU items.

B

menu.

Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.

Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.

UP

Return to the top level

Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù.

Setting addresses and options with the projector disconnected

The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press
the display will switch off again after a wait time of 30 seconds.

ALPHA SPOT HPE 1500 & ST

to momentarily activate the display and thus access the settings. Once the required operations have been carried out,

F

15

Continue

➔

MENU SETTING

13

mx

Set Up

Option

nformation

I

anual

M

ontrol

C

est

T

Advanced

D

ddress

A

hannel

C

ode

M

ixture ID

F

Ethernet

nterface

I

4

Manual
Control

Lamp

Reset

Channel

2

ystem

Option

Lamp Dmx

Pan / Tilt

olor

C

Shutter

Autofocus

Mode

Macro

Effects

Silent
Mode

nvert

I

an

P

nvert

I

ilt

T

Swap

Pan-Tilt

Encoder

Pan-Tilt

P/T Homing

Mode

an Home

P

ef Pos

D

ilt Home

T

ef Pos

D

Color

ixing

M

ixed Wheel

F

Shortcut

Macro Color

Adjustment

Shutter

On Error

r O

e

m

im

D

r

tte

u

Sh

Limited Zoom

Range

Complete

Zoom Range

Macro group

size

Macro

fixture Id

Standard

Information

n

S

rrors

E

ixture

F

ours

H

Lamp

ours

H

Lamp

Strikes

System

ersion

V

Board

iagnostic

d

Dmx

onitor

M

ans

F

Monitor

Sensor

Status

Network

parameters

Test

ALPHA SPOT HPE 1500 & ST

Pan / Tilt

Colour

Beam

Gobo

All

Lamp

Dimming

Power Mode

Display

Setting

16

Quiet

1500W-

800W

1500W-

1200W

1500-1200

Full fan speed

1200

Low fan speed

1500-1200

Auto fan speed

Default Preset

User Preset 1

User Preset 2

UserPreset 3

65

Advanced

Access code

1234

Upload

Firmware

Setup
Model

Calibration

NOTE: On grey the default options

mx

Set Up

D

ddress

A

Address xxx

SET UP MENU

DMX ADDRESS
NOTE: without the DMX signal the Address (XXX) flashing

Allows you to select the DMX ADDRESS

1) Press

2) Use the UP
Address.

3) Press

- the current DMX Adress appear on the display.

F

, DOWN C, RIGHT Ekeys to plan the DMX

B

to confirm the selection or LEFT Dto keep current settings.

F

hannel

C

ode

M

Fixture Id

Ethernet

nterface

I

Standard

ector

V

alue xxx

V

Control

Protocol

CHANNEL MODE

Allows you to select a channel arrangement from the two available.

1) Press
Vector).

2) Use the UP
settings:

- Standard

- Vector

3) Press

FIXTURE ID

Allows you to select the FIXTURE ID

1) Press

2) Use the UP

3) Press

ETHERNET INTERFACE

It lets you set the Ethernet settings to be attributed to the projector.

1) Premere

2) Use the UP
options to set:

Control Protocol

It lets you select the “Control Protocol” Art-net to assign according to the
control unit used:

1) Press

2) Use the UP

- Disabled

- Art-net on IP 2

- Art-net on IP 10

3) Press

- the current settings appear on the display (Standard or

F

and DOWN Ckeys to select one of the following

B

to confirm the selection or LEFT Dto keep current settings.

F

- the current Fixture ID appear on the display.

F

, DOWN C, RIGHT Ekeys to plan the Fixture ID.

B

to confirm the selection or LEFT Dto keep current settings.

F

.

F

and DOWN Ckeys to select the “Ethernet Interface”

B

the current setting appears on the display.

F

and DOWN Ckeys to select one of the following settings:

B

to confirm the selection or LEFT Dto keep the current setting.

F

ALPHA SPOT HPE 1500 & ST

Repeat on

DMX

Universe

Custom IP

address

Custom IP

mask

Repeat on DMX

It lets you enable the transmission of the Ethernet protocol by DMX signal
to all the connected projectors.

1) Press

2) Use the UP

- Disabled: DMX transmission disabled.

- Enabled on primary: DMX transmission enabled.

3) Press

Universe

It lets you assign the “Universe” number to be assigned to a series of
projectors.

1) Press

2) Use the UP

3) Press

Custom IP address
Allows you to set the IP address manually by the user default.

Custom IP mask

Allows you to set manually the Subnet Mask by the user default.

17

the current setting appears on the display.

F

and DOWN Ckeys to select one of the following settings:

B

to confirm the selection or LEFT Dto keep the current setting.

F

– the current Universe address appears on the display.

F

, DOWN C, RIGHT Ekeys to set the Universe address.

B

to confirm the selection or LEFT Dto keep the current setting.

F

Continue

➔

Option

Lamp Dmx

OPTIONS MENU

n

O

ff

O

LAMP DMX

Used for enabling lamp remote control channel.

1) Press

2) Use the UP
the lamp remote control channel.

3) Press

- the current settings appear on the display (On or Off).

F

and DOWN Ckeys to enable (On) or disable (Off)

B

to confirm the selection or LEFT Dto keep current settings.

F

Pan / Tilt

nvert

I

an

P

Invert

ilt

T

wap

S

Pan-Tilt

Encoder

Pan-Tilt

O

O

O

Off

O

Off

On

Off

n

ff

n

n

PAN / TILT
Invert pan

Used for reversing Pan movement.

1) Press

2) Use the UP
PAN inversion.

3) Press

Invert tilt

Used for reversing tilt movement.

1) Press

2) Use the UP
Tilt inversion.

3) Press

Swap Pan-Tilt

Used for swapping Pan and Tilt channels (as well as Pan fine and Tilt fine).

1) Press

2) Use the UP
Pan and Tilt channel swap.

3) Press

Encoder Pan-Tilt

Used for enabling the Pan / Tilt encoders.

1) Press

2) Use the UP
Pan / Tilt encoders.

3) Press

You can quickly disable the Pan and Tilt Encoder by simultaneou­sly pressing the UP

- the current settings appear on the display (On or Off).

F

and DOWN Ckeys to enable (On) or disable (Off)

B

to confirm the selection or LEFT Dto keep current settings.

F

- the current settings appear on the display (On or Off).

F

and DOWN Ckeys to enable (On) or disable (Off)

B

to confirm the selection or LEFT Dto keep current settings.

F

- the current settings appear on the display (On or Off).

F

and DOWN Ckeys to enable (On) or disable (Off)

B

to confirm the selection or LEFT Dtto keep current settings.

F

- the current settings appear on the display (On or Off).

F

and DOWN Ckeys to enable (On) or disable (Off)

B

to confirm the selection or LEFT Dto keep current settings.

F

and DOWN Ckeys in the ''Main Menu''.

B

P/T Homing

Mode

Pan Home

Def Pos

Standard

Sequenced

P/T Homing Mode

Lets you set the initial projector Reset mode.

1) Press

2) Use the UP
settings:

Standard: Pan & Tilt are simultaneously reset.
Sequenced: Tilt is reset first followed by Pan.

3) Press
setting.

Pan Home Def Pos

Lets you assign the Pan channel “home” position at the end of Reset,
without a DMX input signal.

1) Press

2) Use the UP
settings:

0 degree
90 degrees
180 degrees
270 degrees (default)

3) Press
setting.

, the current setting appears on the display.

F

and DOWN Ckeys to select one of the following

B

to confirm the selection or LEFT Dto keep the current

F

, the current setting appears on the display.

F

and DOWN Ckeys to select one of the following

B

to confirm the selection or LEFT Dto keep the current

F

ALPHA SPOT HPE 1500 & ST

18

Option Pan / Tilt

ilt Home

T

ef Pos

D

Tilt Home Def Pos

Lets you assign the Tilt channel “home” position at the end of Reset,
without a DMX input signal.

1) Press

2) Use the UP

ettings:

s

0%

12.5%
25%
50% (default)
75%

87.5%
100%

3) Press

etting.

s

, the current setting appears on the display.

F

F

and DOWN Ckeys to select one of the following

B

to confirm the selection or LEFT Dto keep the current

Color

olor

C

ixing

M

Fixwheel

Shortcut

Macro Color

Adjustment

GB

R

CMY

O

O

On

Off

COLOR
Color mixing

Used for reversing the CMY color mixing system.

1) Press

2) Use the UP

RGB color mixing mode
CMY color mixing mode

3) Press

n

ff

Fixed wheel short-cut

Used for optimizing color change time so that the disc turns in the direc­tion that requires shorter movement.

1) Press

2) Use the UP
color change optimization.

3) Press

Macro color adjustment

It lets you enable the overwriting of a “Macro Colour” with the Cyan,
Magenta, Yellow, CTO and Colour wheel channels.
Press

1) Use the UP
the overwriting.

2) Press

- the current settings appear on the display (On or Off).

F

and DOWN Ckeys select one of the following settings:

B

to confirm the selection or LEFT Dto keep current settings.

F

– the current settings appear on the display (On or Off).

F

and DOWN Ckeys to enable (On) or disable (Off)

B

to confirm the selection, or LEFT Dto keep current settings.

F

the current setting appears on the display.

F

and DOWN Ckeys to enable (On) or disable (Off)

B

to confirm the selection or LEFT Dto keep the current setting.

F

Shutter

Auto-focus

Mode

Shutter

On Error

Dimmer On

Shutter

Limited

Zoom Range

Complete

Zoom Range

On

Off

On

Off

SHUTTER
Shutter on error

Used for automatically closing the stop/strobe in the event of Pan/Tilt
position error.

1) Press

2) Use the UP
automatic stop/strobe closing in the event of Pan/Tilt position error.

3) Press

Dimmer on Shutter

Enables automatic closing of the dimmer when the strobe is completely closed.

1) PressF– the current settings appear on the display (On or Off).

2) Use the UP
the automatic closing of the dimmer.

3) Press

AUTO-FOCUS MODE

It lets you select the “Auto-focus Mode” from the two available.

1) Press

2) Use the UP
Limited Zoom Range: The “Autofocus” works only in the optical run
that was specifically designed for the projector in question.
Complete Zoom Range: The “Autofocus” also works in overrun

3) Press

- the current settings appear on the display (On or Off).

F

and DOWN Ckeys to enable (On) or disable (Off)

B

to confirm the selection, or LEFT Dto keep current settings.

F

and DOWN Ckeys to enable (On) or disable (Off)

B

to confirm the selection or LEFT Dto keep current settings.

F

the current setting appears on the display.

F

and DOWN Ckeys to select one of the following settings:

B

to confirm the selection or LEFT Dto keep the current setting.

F

ALPHA SPOT HPE 1500 & ST

19

Continue

➔

M

E

acro

ffects

acro group

M

size

MACRO EFFECTS

It lets you select the “Macro Effects” set up from the two available.

1) Press

2) Use the UP

Macro group size

It lets you set the number of projectors to be included in the macro mode
operation.

1) Press

2) Use the UP B, DOWN C, RIGHT keys to set the number of projectors
to be included in the “Macro Effect” operation.

3) Press

the current setting appears on the display.

F

and DOWN Ckeys to select one of the following settings:

B

F

to confirm the selection or LEFT Dto keep the current setting.

F

Silent
Mode

Lamp

Dimming

acro fixture Id

M

tandard

S

Quiet

1500W-

800W

1500W-

1200W

Macro fixture Id

It lets you attribute an ID address to the projector for the phase
displacement for the scene’s starting time in Macro mode.

1) Press

2)

3) Press

SILENT MODE

It lets you select the “Silent Mode” from the two available.

1) Press

2)

3) Press Fto confirm the selection or LEFT Dto keep the current

LAMP DIMMING

This lets you select the lamp “dimmer” mode, selecting one of the two
available modes:

• 1500W-800W: Default settings, the lamp electronically "dims” from

• 1500W-1200W: The lamp electronically “dims” from 1500W to 1200W

F

Use the UP Band DOWN Ckeys to select one of the following settings:
Fixed to X. (to assign to all the projectors to be included in the Macro
operation).
Auto by DMX Address: According to the DMX address, it automatically
detects the starting sequence of the scene in the Macro mode (to assign
to all the projectors to be included in the Macro operation).

to confirm the selection or LEFT Dto keep the current setting.

F

the current setting appears on the display.

F

Use the UP Band DOWN Ckeys to select one of the following settings:

Standard: Maximum speed and consequently maximum effects noise level.
Quiet: reduces the speed of some effects, thereby reducing their noise level.

setting.

1500W to 800W and mechanically dims from 800W to 0. Visually, the
Dimmer curve is high performance but a slight flicker is noted in some
dimming positions.

and mechanically dims from 1200W to 0. No lamp flicker is visible
when this option is selected. The "dimmer" blades are subject to
higher thermal stress. Thus, more frequent "dimmer" blade
maintenance may be required.

Power Mode

ALPHA SPOT HPE 1500 & ST

1500-1200

Full fan speed

1200

Low fan speed

1500-1200

Auto fan speed

POWER MODE

Allows you to select a Power Mode from the three available.

1) Press

2) Use the UP

- 1500-1200W Full fan speed: Lamp can change from full-power

(1500W) to half-power (1200W) using the LAMP CONTROL channel.
Fans always work at Full speed

- 1200W Low fan speed: Lamp constantly works in half-power mode

(1200W) while the Fan always works at Low speed. With LAMP
CONTROL channel you can only switch the lamp ON and OFF.

- 1500-1200W Auto fan speed: Lamp can change from full-power

(1500W) to half-power (1200W) using the LAMP CONTROL channel.
Automatically the fans switch from Full speed to Low speed respectively.

3) Press

20

- the current settings appear on the display.

F

and DOWNCkeys to select one of the following settings:

B

to confirm the selection or LEFT Dto keep current setting.

F

D

isplay

On

O

DISPLAY

ff

Used for automatically reduce brightness on the display after about 30

econds in idle.

s

1) Press

- the current settings appear on the display (On or Off).

F

2) Use the UPBand DOWN Ckeys to enable (On) or disable (Off)

the decreasing of display brightness.

3) Press

ettings.

s

to confirm the selection or LEFT Dto keep current

F

etting

S

Default

reset

P

User

reset 1

P

User

reset 2

P

User

reset 3

P

Reset To

afault

D

Go Back

Load
reset 1

P

ave To

S

reset 1

P

Load
reset 2

P

ave To

S

reset 2

P

Load

Preset 3

ave To

S

reset 3

P

SETTING

Used to save 3 different settings of the items in the options menu and
relative submenus.

1) Press

- “Default preset” appears on the display.

F

2) Use the UPBand DOWN Ckeys to select one of the following
configurations:

- Default preset (*)

- User preset 1

- User preset 2

- User Preset 3

3) Press

4) Use the UP

- “Load preset X” appears on the display.

F

and DOWN Ckeys to select:

B

- Load preset X to recall a previously stored configuration.

- Save to preset X to store the current configuration.
a confirmation message (Are you sure?) appears on the display.

5) Select YES to confirm the selection or NO to keep the current setting
and return to the next higher level.

(*) DEFAULT PRESET

By pressing the RIGHT

key and the LEFTDkey simultaneously

E

once entered in the "main menu" it is possible to quickly (short cut)
reset the default settings (DEFAULT PRESET).

Used for restoring default values on all options menu items and relevant
submenus.

1) Press F, a confirmation message (Are you sure?) appears on the
display.

2) Select YES to confirm the selction or NO to keep current setting.

OPTION DEFAULT
Lamp DMX On
Invert Pan Off
Invert Tilt Off
Swap Pan-Tilt Off
Encoder Pan-Tilt On
P/T Homing Mode Standard
Pan Home Def Pos 270 degrees
Tilt Home Def Pos 50%
Colour mixing CMY
Fixed Wheel Shortcut On
Macro Color Adjustment On
Shutter on error Off
Dimmer on Shutter Off
Auto-focus mode Limited zoom range
Silent mode Standard
Power mode 1500-1200w full fan speed
Display On

ALPHA SPOT HPE 1500 & ST

21

Continue

➔

INFORMATION MENU

Information

System

Errors

ixture

F

Hours

Lamp

Hours

Total XXX
Partial XXX

Total XXX
Partial XXX

eset...

R

eset...

R

SYSTEM ERRORS

Shows a list of warnings and messages relevant to errors occurred since
the fixtures switching-on.

1) Pressing

you are allowed to reset the SYSTEM ERRORS list.

F

A confirmation message (Are you sure you want to clear error list ?)
appears on the display.

2) Select YES to reset the list or NO to go back.

FIXTURE HOURS

Used for displaying projector operating hours (total and partial).

1) Press

otal counter

T

- Hours total and partial appears on the display.

F

Counts the number of projector working life hours (from manufacture to date).

Partial counter

Counts the number of partial projector working life hours since the
last reset to date.

2) Press

to reset partial projector working hours a confirmation

F

message (Are you sure?) appears on the display.

3) Select YES to reset partial projectors counter or NO to keep the
current setting and return to the top menu level.

LAMP HOURS

Used for displaying the lamp working hours (total and partial).

1) Press

- Hours total and partial appears on the display.

F

Total counter

Counts the number of projector working hours with the lamp on (from
manufacture to date).

Partial counter

Counts the number of lamp working hours since the last reset to date.

2) Press

to reset partial lamp working hours, a confirmation message

F

(Are you sure ?) appears on the display.

3) Select YES to reset partial counter or NO to keep the current setting and
return to the top menu level

Lamp

Strikes

System
Version

Total XXX
Partial XXX

Reset...

Board Revis. Hw.rv.
CPU brd x.x.x x.x
com.dev x.x
0: PT-3f x.x x.x
1: 8-Ch x.x x.x
2: 8-Ch x.x x.x
3: 8-Ch x.x. x.x

LAMP STRIKES

Used for displaying the number of times the lamp was turned on (total and
partial).

1) Press

- the number of times the lamp was turned on (total and

F

partial) appears on the display.

Total counter

Counts the number of times the lamp was turned on (from manufacture
to date).

Partial counter

Counts the number of times the lamp was turned on since the last
reset to date.

2) Press

to reset partial lamp strikes hours, a confirmation message

F

(Are you sure ?) appears on the display.

3) Select YES to reset partial counter or NO to keep the current setting
and return to the top menu level

SISTEM VERSION

Used for displaying the software and hardware version of each board
installed in the projector.
CPU brd (CPU board)
0: PT-3f (Pan / Tilt board)
1: 8-Ch (8 channel board)
2: 8-Ch (8 channel board)
3: 8-Ch (8 channel board)

ALPHA SPOT HPE 1500 & ST

22

oard

B

Diagnost.

oard Status Err%

B

:PT-3f Good 0.00

0

:8-Ch Good 0.00

1

:8-Ch Good 0.00

2
3:8-Ch Good 0.00

BOARD DIAGNOSTIC

Used for displaying the status error of each board installed in the projector:
0: PT-3f (Pan / Tilt board)
1: 8-Ch (8 channel board)
2: 8-Ch (8 channel board)
3: 8-Ch (8 channel board)

mx

D

onitor

M

ans

F

onitor

M

Sensor

Status

Network

params

Fan Speed (RPM)

wr.Sup XXXX

P

all.In. XXXX

B
Ball.Out XXXX
Eff.In XXXX

ff.Out XXXX

E

amp XXXX

L
Lamp XXXX
Gobo XXXX
Board XXXX

DMX MONITOR

Used for displaying the projector DMX channel level in bit (Val) and in
percentage (Perc).

FANS MONITOR

Used for displaying the speed of each fan installed in the projector:
Pwr.Sup (Power supply Fan)
Ball. IN (Ballast IN Fan)
Ball. Out (Ballast OUT Fan)
Eff.IN (Effects IN Fan)
Eff.OUT (Effects OUT Fan)
Lamp (Lamp Fan)
Lamp (Lamp Fan)
Gobo (Gobo Fan)
Board (Yoke Board Fan)

SENSOR STATUS

It lets you check the correct operations of each "sensor” installed in the
projector, each channel is associated with one of the following three
parameters:

• n.a.= sensor not available

• ON= sensor working

• OFF= sensor defective

NETWORK PARAMS

Allows the "Network" parameters of the projector to be displayed or:

IP address: Internet Protocol address (two projectors must not have the
same IP address)

IP mask: 255.0.0.0
Mac address: Media Access Control: the projector’s Ethernet Address.

Manual

Control

Lamp

Reset

Channel

On

Off

No

Yes

MANUAL CONTROL

LAMP

Used for turning lamp on and off from the projector control panel.

1) Pres

s F-

the current settings appear on the display (On or Off).

2) Use the

3) Press

RESET

Used for resetting the projector.

1) Press

2) Select YES to starting reset the fixture or NO to keep the current setting

CHANNEL

Used for setting channel levels from the projector control panel.

1) Press

2) Use the UP

3) Press

4) Press LEFT

UP Band DOWN Ckeys to turn the lamp on (On) or off (Off)

to confirm the selection or

F

LEFT Dto keep current settings

and return to the top level.

to reset the projectors, a confirmation message (Are you sure ?)

F

appears on the display.

and return to the top menu level.

- the first channel appears on the display.

F

and DOWN Ckeys to select the required channel:

B

and use the UP Band DOWN Ckeys to select the

F

required DMX level (value between 0 and 255).

to return to the top menu level.

D

ALPHA SPOT HPE 1500 & ST

23

Continue

➔

Test

Advanced

an-Tilt

P

olour

C
Beam

obo

G

ll

A

ode

C
1234

TEST MENU

AUTOTEST

Allows you to check the proper functioning of effects.

) Press

1

2) Use the UP

3) Press
m

Test sequence:

Pan - Tilt effects (Pan & Tilt)

-

- Colour effects (CMY, colour wheel)

- Beam effects (Stopper-Strobe / Dimmer / Iris / Prism / Frost / Focus /

oom, Animation disk)

Z

- Gobo effects (Fixed gobo / Rotating gobo)

- All effects

F

F

enu level.

.

and DOWN Ckeys to select the required test.

B

to confirm the selection or LEFT Dto return to the top

ADVANCED MENU

To enable the "Advanced Menu" set up the "Access code" (1234) using the
UP

, DOWN C, RIGHT Ekeys.

B

Press

- "Menu advanced" appears on the display

F

pload

U

irmware

F

Setup

Model

Calibration

Transfer the firmware on all

he connected fixtures ?

t

re you sure ?

A

es/No

Y

Changing to a wrong model
may damage the fixture.
Are you sure ?
Yes/No

UPLOAD FIRMWARE

Allows you to transfer the firmware from 1 fixture to all the connected fixtures.

1) Press

2) Select YES to start the firmware loading or NO to keep the current set­ting and return to the top menu level

SETUP MODEL

Allows you to change the default model of projector.

1) Press

2) Select YES to define the model of projector or NO to keep the current
setting and return to the top menu level.

CALIBRATION

Allows you to adjust effects from the control panel to obtain perfect unifor­mity between the projectors.

1) Press

2) Using the UP
regulate.

3) Press
make the adjustment by setting a value between 0 and 255.

4) Press
tings and return to the top level.

, a confirmation message appears on the display.

F

a confirmation message appears on the display.

F

- “channels” appears on the display.

F

and DOWN Ckeys, select the effect you wish to

B

and use the RIGHT E, UPBand DOWN Cbuttons to

F

to confirm the selection

F

or

LEFT Dto keep current set-

ALPHA SPOT HPE 1500 & ST

FACTORY DEFAULT

Allows you to restore default values of all channels (128).

1) Press
calibration to factory default ?).

2) Select YES to reset calibration to factory default or NO to keep the
current setting and return to the top menu level.

24

– a confirmation message appears on the display (Reset

F

1/4 Turn

1

3

2

1

2

1/4 Turn

1

4

5

MAINTENANCE

11 12

Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section.
Opening the head covers - Fig. 11.

Closing the head covers - Fig. 12.

ALPHA SPOT HPE 1500 & ST

Continue

25

➔

Lower Side

2

1

1

2

1

2

1

3

4

1

Lamp change - Fig 14
Take the new lamp out of its package and insert in the fitting.

WARNING: do not touch the lamp’s envelope with bare hands.
Should this happen, clean the bulb with a cloth soaked in alcohol
and dry it with a clean, dry cloth.

15

Opening and closing lamp compartment - Fig. 13

16

Lamp regulation - Fig. 15
To centre the lamp, turn the three adjusting screws as shown in the figure.
CAUTION:
Fast lamp ON-OFF cycles (for example 10 minutes ON / 10 minutes
OFF) will reduce the lamp life.

Fan support plate opening and closing (Lower side) - Fig. 16

ALPHA SPOT HPE 1500 & ST

26

Upper Side

2

1

17

2

1

085911/001

085901/001

085903/001

085907/001

085912/001

085906/001

085904/001

085908/001

Black Side

Black Side

Lower Side

Fan support plate opening and closing (Upper side) - Fig. 17

18

Replacing fixed gobos (ø 31.5 mm - max 25 mm image - thickness max 1 mm) - Fig. 18
IMPORTANT: Please contact CLAY PAKY before using customized gobos.
To facilitate fixed gobo insertion and removal from the respective wheels. Clay Paky has created 2 templates, ATT019/001 and ATT020/001,
which facilitate these operations and preserve gobo integrity. For further information please contact Clay Paky.

ALPHA SPOT HPE 1500 & ST

27

Continue

➔

19

Lower Side

1

2

GOBO ROTATION 1

084632/001

105115/802 084629/001

084628/001

105115/801 084624/001

GOBO
INDEX

GOBO ROTATION 2

084633/001

084630/001 084626/001

084627/001

084631/001 084625/001

GOBO
INDEX

1

2

Bearing group replacement - Fig. 19

20

Replacing rotating gobos (ø 37.5 mm - max 25 mm image – thickness 1 mm) - Fig. 20
IMPORTANT: Please contact CLAY PAKY before using customized gobos.
IMPORTANT: Use only glass gobos on the rotating gobos wheels.

ALPHA SPOT HPE 1500 & ST

28

Upper Side Lower Side

21

COATED GLASS GOBOS TYPE 1 COATED GLASS GOBOS TYPE 2

Grey/Black side away

rom lamp

f

Reflective side towards lamp

Gobo orientation - Fig. 21
The pictures shown the correct gobos orientation.

22

oated side

C

Coated side

towards lamp

Uncoated
side

Uncoated side

To determine which side of a godo is coated, hold an odject up to it. On the
uncoated side, there is a space between the object and its reflection.

Periodical cleaning - Fig. 22
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The
frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the
working environment (air humidity, presence of dust, salinity, etc.).
Use a soft cloth dampened with any detergent liquid for cleaning glass to remove the dirt from the reflectors, from the lenses and filters. It is recommended
that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:

• General cleaning of internal parts.

• Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Clay Paky.

• General visual check of the internal components, cabling, mechanical parts, etc.

• Electrical, photometric and functional checks; eventual repairs.

ALPHA SPOT HPE 1500 & ST

29

Continue

➔

4

3

5

2

Lower Side

Thermostat

1

6

23

Extraction of the effect modules: Preliminary operations - Fig. 23

ALPHA SPOT HPE 1500 & ST

30

11

16

15

14

17

10

18

12

13

6

7

9

8

Lower Side

Upper Side Upper Side

24

Extraction of the effect modules - Fig. 24
IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged.
Insertion of the effect modules: Repeat the operations indicated in Fig. 24 and 25 in reverse order

ALPHA SPOT HPE 1500 & ST

31

Continue

➔

22

26

21

24

19

23

25

20

U

pper Side

Upper Side

Upper Side

Upper Side

25

Extraction of the effect modules - Fig. 25
IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged.
Insertion of the effect modules: Repeat the operations indicated in Fig. 24 and 25 in reverse order

ALPHA SPOT HPE 1500 & ST

32

6

4

3

5

2

1

26

Battery removal - Fig. 26

This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery
at the end of its life according to the regulation in force.

LiFePO4

Pb

ALPHA SPOT HPE 1500 & ST

33

660

(25.98")

628

(24.72")

488

(19.21")

843

(33.19")

232

(9.13")

500

(19.69")

480

(18.90")

740

(29.13")

TECHNICAL INFORMATION

Power supplies available

200-240V 50/60Hz

Input power

2000VA a 230V 50Hz.

Total output

Max 27000 lumens Spot HPE 1500
Max 24800 lumens Spot HPE 1500 ST

amp

L

Discharge lamp.
Type HTI 1500W/60/P50-L Lok-it Osram (L10102)

- Cap PGJ50

- Colour temperature 6000 K

- Luminous flux 135000 lm

- Average life 750 h

- Any working position

Motors

27 stepper motors, operating with microsteps,
totally microprocessor controlled.

Optical unit

Elliptic reflector with high luminous efficiency

Channels

Max 40 control channels.

IP20 protection rating

• Protected against the entry of solid bodies larger
than 12mm (0.47”).

• No protection against the entry of liquids.

Safety Devices

• Bipolar circuit breaker with thermal protection.

• Automatic break in power supply in case of
overheating or failed operation of cooling system.

ooling

C

Forced ventilation with axial fans.

Body

• Aluminium structure with die-cast plastic cover.

• Two side handles for transportation.

• Device locking PAN and TILT mechanisms for
transportation and maintenance.

Working position

Functioning in any position.

Weights

50.95 Kg (112lbs, 1oz).

THE PROJECTOR WILL NOT SWITCH ON

ELECTRONICS NON-OPERATIONAL

DEFECTIVE PROJECTION

REDUCED LUMINOSITY

POSSIBLE CAUSES CHECKS AND REMEDIES

No mains supply.
Lamp exhausted or defective.
Signal transmission cable faulty or disconnected.
Incorrect addressing.
Fault in the electronic circuits.
Lenses or reflector broken
Dust or grease deposited.

Inputs

DMX 512
Ethernet

Movable body

•

Movement by means of two stepper motors, con­trolled by microprocessor.

•

Automatic repositioning of PAN and TILT after
accidental movement not controlled by control
unit.

•

Travel:

- PAN = 540°

- TILT = 252°

•

Maximum speeds:

- PAN = 4.0 sec (360°)

- TILT = 3.2 sec (252°)

•

Resolution:

- PAN = 2.11°

- PAN FINE = 0.008°

- TILT = 0.98°

- TILT FINE = 0.004°

CAUSE AND SOLUTION OF PROBLEMS

Check the power supply voltage.
Replace the lamp. (See instructions).
Replace the cables.
Check addresses (see instructions).
Call an authorised technician.
Call an authorised technician.
Clean (see instructions).

PROBLEMS

ALPHA SPOT HPE 1500 & ST

34

ALPHA SPOT HPE 1500

HANNEL

C

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

CYAN
MAGENTA

ELLOW

Y

.T.O

C
COLOUR WHEEL
MACRO COLOURS
STOP/STROBE
DIMMER
DIMMER FINE
IRIS
ANIMATED STAR GOBO
STATIC GOBO CHANGE
ROTATING GOBO 1 CHANGE
GOBO 1 ROTATION
GOBO 1 FINE
ROTATING GOBO2 CHANGE
GOBO2 ROTATION
GOBO2 FINE
ANIMATION DISK INSERTION
ANIMATION DISK ROTATION
ROTATING PRISM INSERTION
PRISM ROTATION
FROST INSERTION
FOCUS
FOCUS FINE
ZOOM
AUTOFOCUS DISTANCE
AUTOFOCUS ADJUSTMENT
MACRO EFFECTS
PAN
PAN FINE
TILT
TILT FINE
FUNCTION
RESET
LAMP ON/OFF (with Option "Lamp DMX" ON)

CHANNEL FUNCTION

NB: To prevent accidental breakage of the effects,
which could collide with each other during transport,
before switching the projector OFF check that all the
projector Channels have been excluded (DMX level = 0 bit).

HANNEL MODE

C

STANDARD VECTOR

CYAN
MAGENTA

ELLOW

Y

.T.O

C
COLOUR WHEEL
MACRO COLOURS
STOP/STROBE
DIMMER
DIMMER FINE
IRIS
ANIMATED STAR GOBO
STATIC GOBO CHANGE
ROTATING GOBO 1 CHANGE
GOBO 1 ROTATION
GOBO 1 FINE
ROTATING GOBO2 CHANGE
GOBO2 ROTATION
GOBO2 FINE
ANIMATION DISK INSERTION
ANIMATION DISK ROTATION
ROTATING PRISM INSERTION
PRISM ROTATION
FROST INSERTION
FOCUS
FOCUS FINE
ZOOM
AUTOFOCUS DISTANCE
AUTOFOCUS ADJUSTMENT
MACRO EFFECTS
PAN
PAN FINE
TILT
TILT FINE
FUNCTION
RESET
LAMP ON/OFF (with Option "Lamp DMX" ON)
PAN-TILT TIME
COLOUR TIME
BEAM TIME
GOBO TIME

ALPHA SPOT HPE 1500 & ST

35

Continue

➔

BIT EFFECT

255

COLOUR EXCLUDED

0

COLOUR INSERTED

CHANNEL 1

CYAN

CHANNEL 2

MAGENTA

CHANNEL 3

YELLOW

BIT EFFECT

255

C

OLOUR INSERTED

0

COLOUR EXCLUDED

CHANNEL 1

CYAN

CHANNEL 2

MAGENTA

CHANNEL 3

YELLOW

OTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 128 bit - Tilt 128 bit) all the others channels stay at 0 bit.

BIT EFFECT

0

FILTER EXCLU DED

255

FILTER INSERT ED

CHANNEL 4

CTO

BIT EFFECT

255

FAST ROTATION 160 rpm

128

0

SLOW ROTATION 0.2rpm

BLUE

ORANGE

AQUAMARINE

GREEN

PINK

RED

WHITE

117

97

77

58

39

20

N

COLOUR MIXING - channel 1 - 2 - 3

•

peration with option color mixing: RGB

O

IMPORTANT: The lamp dim to half power 1 second after all the 3 channels stay at 0 bit

evel. The lamp goes back to full power when the channels level is put higher than 0 bit.

l

Operation with option color mixing: CMY

IMPORTANT: The lamp dim to half power 1 second after all the 3 channels
stay at 255 bit level. The lamp goes back to full power when the channels level
is put lower than 255 bit.

• C.T.O. - channel 4

• COLOUR WHEEL - channel 5

ALPHA SPOT HPE 1500 & ST

MACRO COLOURS - channel 6

•

COLOR NAME BIT ROSCO LEE CYAN

nused Range 148-255 -- - - ---

U

alf CT straw 146-147 442 442 00 34 190 0

H

ighter blue 144-145 353 353 226 0 149 138 0

L

lacier blue 142-143 352 352 220 0 129 138 0

G

uschia pink 140-141 345 345 109 186 77 120 0

F

allard green 138-139 325 325 255 00236 58

M

ade 136-137 323 323 127 0 162 0 77

J

/4 CT Orange 134-135 285 285 0 36 61 217 0

3

/4 CTB 132-133 281 281 85 79 87 54 0

3

alf minus green 130-131 248 248 60 19 86 75 39

H

inus green 128-129 247 247 60 71 86 75 39

M

/4 CTO 126-127 206 206 62 71 123 122 0

1

/2 CTO 124-125 205 205 25 26 45 131 0

1

ull CT Orange 122-123 204 204 0 44 58 234 0

F

/4 CTB 120-121 203 203 75 54 91 109 0

1

/2 CTB 118-119 202 202 85 71 84 89 0

1

ull CTB 116-117 201 201 94 79 80 00

F

lice Blue 114-115 197 197 236 51 0 205 0

A

ongo Blue 112-113 181 181 251 241 0 255 0

C

ark Lavender 110-111 180 180 195 170 0 160 0

D

hrome Orange 108-109 179 179 0 98 255 255 0

C

agoon blue 106-107 172 172 224 0 121 40 79

L

eep Lavender 104-105 170 170 100 129 77 120 0

D

iliac tint 102-103 169 169 41 59 39 120 0

L

aylight Blue 100-101 165 165 210 73 105 88 0

D

lame red 98-99 164 164 0 255 227 255 97

F

ODE CODE BIT BIT BIT BIT BIT

C

MAGENTA

YELLOW CTO WHEEL

Bastard amber 96-97 162 162 0 26 0 199 0
Deep Orange 94-95 158 158 0 148 255 255 0
Pink 92-93 157 157 0 159 0 255 0
Pale rose 90-91 154 154 0 48 0 189 0
Pale Gold 88-89 152 152 0 60 98 138 0
Bright rose 86-87 148 148 0 255 0 255 0
Apricot 84-85 147 147 0 81 55 255 0
Bright Blue 82-83 141 141 182 0 99 92 77
Primary green 80-81 139 139 00 0231 58
Light green 78-79 121 121 00255 0 77
Pale green 76-77 138 138 105 0 179 100 0
Special Lavender 74-75 137 137 97 105 72 90 0
Pale Lavender 72-73 136 136 73 102 44 120 0
Deep golden amber 70-71 135 135 0 255 255 255 0
Golden amber 68-69 134 134 0 142 234 110 0
Medium blue 66-67 132 132 255 152 127 0 77
Marine blue 64-65 131 131 60 0 106 73 77
Bright pink 62-63 128 128 0 255 0 197 0
Mauve 60-61 126 126 0 255 0 255 74
Fern Green 58-59 122 122 173 0 235 89 0
Leaf green 56-57 121 121 136 0 241 64 0
Deep Blue 54-55 120 120 255 229 58 128 77
Dark blue 52-53 119 119 255 161 0077
Light blue 50-51 118 118 245 0 145 138 0
Steel blue 48-49 117 117 167 0 141 165 0
Medium blue green 46-47 116 116 189 0 157 91 77
Peacock blue 44-45 115 115 136 0 128 91 77
Dark pink 42-43 111 111 0 139 0 220 0
Light Salmon 40-41 109 109 50 121 58 230 0
English rose 38-39 108 108 0 62 0 247 0
Light rose 36-37 107 107 0 95 0 220 0
Primary red 34-35 106 182 00 0020
Orange 32-33 105 105 0 182 255 76 0
Deep amber 30-31 104 104 0 26 199 223 0
Straw 28-29 103 103 58 17 104 176 0
Light amber 26-27 102 102 00171 193 0
Yellow 24-25 101 101 00255 149 0
Spring yellow 22-23 100 100 80 0 227 157 0
Dark Yellow Green 20-21 090 090 255 0 255 204 0
Lime green 18-19 088 088 118 0 241 124 0
Just Blue 16-17 079 079 255 77 0 204 0
Tokyo Blue 14-15 071 071 255 255 0 180 77
Sky blue 12-13 068 068 245 77 64 173 0
Pale blue 10-11 063 063 122 0 112 127 0
Lavender 8-9 058 058 165 186 77 00
Bright Red 6-7 026 026 0 255 0 255 21
Med Yellow 4-5 010 010 48 0 239 115 0
Med bastard amber 2-3 004 004 0 62 78 159 0
Random Macro Color ----- --­(only for Macro effects) 1---- --­Unused Range 0,00 -- - - - --

36

GOBO 8 SHAKE, FAST SPEED

GOBO 8 SHAKE, SLOW SPEED
GOBO 7 SHAKE, FAST SPEED

GOBO 7 SHAKE, SLOW SPEED
GOBO 6 SHAKE, FAST SPEED

GOBO 6 SHAKE, SLOW SPEED
GOBO 5 SHAKE, FAST SPEED

GOBO 5 SHAKE, SLOW SPEED
GOBO 4 SHAKE, FAST SPEED

GOBO 4 SHAKE, SLOW SPEED
GOBO 3 SHAKE, FAST SPEED

GOBO 3 SHAKE, SLOW SPEED
GOBO 2 SHAKE, FAST SPEED

GOBO 2 SHAKE, SLOW SPEED
GOBO 1 SHAKE, FAST SPEED

GOBO 1 SHAKE, SLOW SPEED
F

AST ROTATION (100 rpm)

SLOW ROTATION (5 rpm)
STOP
SLOW ROTATION (5 rpm)

FAST ROTATION (100 rpm)

G

OBO 8

GOBO 7

GOBO 6

GOBO 5

GOBO 4

GOBO 3

GOBO 2

GOBO 1

WHITE

BIT EFFECT

MACRO

255

244
243

232
2

31

220
219

208
207

196
195

184
1

83

172
1

71

160
159

118

114 - 117

113

72

6

4 - 71

5

6 - 63

48 - 55

40 - 47

32 - 39

24 - 31

16 - 23

8 - 15

0 - 7

STOP / STROBE - channel 7

MACRO

BIT EFFECT

2

52 - 255

O

PEN

0 - 3

C

LOSED

213 - 225

RANDOM SLOW STROBE

4

S

LOW STROBE (1 f lash/sec)

103

F

AST STROBE (12 fl ash/sec)

104 - 107

OPEN

1

08

S

LOW PULSATION

2

08 - 212

OPEN

226 - 238

RANDOM MEDIUM S TROBE

2

39 - 251

RANDOM FAST STROBE

207

FAST PULSATION

0

MINIMUM APERTURE

252 - 2

55

M

A

X

IM

U

M A

P

E

R

T

U

R

E

B

IT

EFFECT

2

51

FA

S

T

P

U

L

S

A

T

ION

,

F

A

S

T

CLOS

I

NG

2

12

SL

OW

P

U

LS

ATIO

N, FA

ST C

LOSING

21

1

F

A

ST

PULSA

T

ION, FA

ST O

P

EN

ING

17

2

S

L

OW

PU

LS

A

T

I

O

N

,

FAS

T

O

PEN

I

N

G

17

1

F

AST PULSATION

13

2

SL

O

W PULSATION

1

2

8 - 1

3

1

MAXIMUM APER

TURE

MA

CRO

0

1*

MINIMUM APERTURE

252 - 255

MAXIMUM APERTURE

BIT

EFFECT

251

FAST PULSATION, FAST CLOSING

212

S

LOW PULSATION, FAST CLOSING

211

FAST PULSATION, FAST OPENING

172

SLOW PULSATION, FAST OPENING

171

FAST PULSATION

1

32

SLOW PULSATION

128 - 131

MAXIMUM APERTURE

MACRO

BIT EFFECT

255

0

BIT EFFECT

255

0

DIMMER OPEN

DIMMER CLOSED

•

IMPORTANT: The lamp dim to half power 1 second after the channel stay at

bit level. The lamp goes back to full power when the channel level is put

0

igher than 0 bit.

h

ANIMATED STAR GOBO – channel 11

•

With the "Animated star gobo" on this bit all "Macro effects" that include an Iris scene,

*

use the "Animated Star gobo" instead of the "Iris"

• DIMMER - channel 8

The lamp is linearly dimmed from full power to half power electronicaly and
mechanically from half power to off.

• DIMMER FINE - channel 9

• IRIS - channel 10

• STATIC GOBO CHANGE - channel 12

ALPHA SPOT HPE 1500 & ST

Continue

37

➔

MACRO

GOBO 6 SHAKE, FAST SPEED

G

OBO 6 SHAKE, SLOW SPEED

G

OBO 5 SHAKE, FAST SPEED

GOBO 5 SHAKE, SLOW SPEED
GOBO 4 SHAKE, FAST SPEED

G

OBO 4 SHAKE, SLOW SPEED

G

OBO 3 SHAKE, FAST SPEED

GOBO 3 SHAKE, SLOW SPEED
GOBO 2 SHAKE, FAST SPEED

GOBO 2 SHAKE, SLOW SPEED
G

OBO 1 SHAKE, FAST SPEED

GOBO 1 SHAKE, SLOW SPEED
GOBO 6

GOBO 5

G

OBO 4

GOBO 3

GOBO 2

G

OBO 1

WHITE

B

IT EFFECT

255

235
234

214
213

193
192

172
171

151
150

130

112-129

93-111

7

5-92

56-74

38-55

1

9-37

0-18

0

0° POSITIO N

21

90° POSITIO N

42

180° POSITIO N

63

270° POSITIO N

84

360° POSITIO N

105

4

50° POSITIO N

1

27

5

40° POSI TION

STOP

540°

360°

0°

255

FAS T ROTATION (150 rpm)

193

SLOW ROTATION

(2,2 rph)

191 - 192

STOP

190

SLOW ROTATION

(2,2 rph)

BIT EFFECT

1

28

FAS T ROTATION (150 rpm)

BIT

255

127

0

0

0° POSITIO N

21

90° POSITIO N

42

180° POSITIO N

63

270° POSITIO N

84

360° POSITIO N

105

4

50° POSITIO N

1

27

5

40° POSI TION

STOP

540°

360°

0°

255

FAS T ROTATION (150 rpm)

193

SLOW ROTATION

(2,2 rph)

191 - 192

STOP

190

SLOW ROTATION

(2,2 rph)

BIT EFFECT

1

28

FAS T ROTATION (150 rpm)

BIT

255

127

0

ROTATING GOBO 1 CHANGE - channel 13

MACRO

GOBO 6 SHAKE, FAST SPEED

G

OBO 6 SHAKE, SLOW SPEED

G

OBO 5 SHAKE, FAST SPEED

GOBO 5 SHAKE, SLOW SPEED
GOBO 4 SHAKE, FAST SPEED

G

OBO 4 SHAKE, SLOW SPEED

G

OBO 3 SHAKE, FAST SPEED

GOBO 3 SHAKE, SLOW SPEED
GOBO 2 SHAKE, FAST SPEED

GOBO 2 SHAKE, SLOW SPEED
G

OBO 1 SHAKE, FAST SPEED

GOBO 1 SHAKE, SLOW SPEED
GOBO 6

GOBO 5

G

OBO 4

GOBO 3

GOBO 2

G

OBO 1

WHITE

B

IT EFFECT

255

235
234

214
213

193
192

172
171

151
150

130

112-129

93-111

7

5-92

56-74

38-55

1

9-37

0-18

•

ROTATING GOBO 2 CHANGE - channel 16

•

• GOBO 1 ROTATION - channel 14

• GOBO 1 FINE - channel 15

• GOBO 2 ROTATION - channel 17

• GOBO 2 FINE - channel 18

ALPHA SPOT HPE 1500 & ST

38

ANIMATION DISK INSERTION - channel 19

STOP

FAS T ROTATION (120 rpm)

SLOW ROTATION (3 rph)

SLOW ROTATION (3 rph)

FAS T ROTATION (120 rpm)

BIT EFFECT

191 - 192

255

193

190

128

STOP

540

°

360

°

0

°

POSITION 540°127

POSITION 450°

105

POSITION 360°

84

POSITION 270°

63

POSITION 180°

42

0

POSITION 0°

POSITION 90°

21

BIT EFFECT

2

55

FROST INSERTED

0

FROST EXCLUDED

BIT EFFECT

255

NEAR

0

DISTANT

BIT EFFECT

255

NEAR

0

DISTANT

BIT EFFECT

255

NARROW BEAM

0

WIDE BEAM

B

IT

E

FFECT

255

DISK INSERTED

0

DISK EXCLUDED

BIT EFFECT

255

FAST ROTATION (120 rpm)

0

FAS T ROTATION (120 rpm)

131

SLOW ROTATION (4,4 rph)

125 - 130

STOP

124

SLOW ROTATION (4,4 rph)

BIT EFFECT

128

PRISM EXCLUDED

0

255

PRISM INSERTED

127

•

FROST - channel 23

•

• ANIMATION DISK ROTATION - channel 20

• PRISM INSERTION - channel 21

FOCUS - channel 24

•

• FOCUS FINE -channel 25

• PRISM ROTATION - channel 22

ALPHA SPOT HPE 1500 & ST

• ZOOM - channel: 26

39

Continue

➔

B

IT

255

0

BIT

255

0

B

IT

255

0

BIT

255

0

AUTOFOCUS DISTANCE - channel 27

B

IT

E

FFECT

255

100 METRES

50 METRES

40 METRES

30 METRES

20 METRES

10 METRES

3 METRES

AUTOFOCUS OFF

128

102

77

51

26

7

0-6

BIT

EFFECT

232-255 STAND BY BLACK

220-231 RANDOM MACRO 8

208-219 RANDOM MACRO 7

196-207 RANDOM MACRO 6

184-195 RANDOM MACRO 5

172-183 RANDOM MACRO 4

160-171 RANDOM MACRO 3

148-159 RANDOM MACRO 2

136-147 RANDOM MACRO 1

112-135 STAND BY BLACK

100-111 MACRO 8

88-99 MACRO 7

76-87 MACRO 6

64-75 MACRO 5

52-63 MACRO 4

40-51 MACRO 3

28-39 MACRO 2

16-27 MACRO 1

12-15 STAND BY BLACK

8-11 STAND BY

0-7 MACRO OFF

BIT EFFECT

128

0

255

FOCUS FINE

FOCUS FINE

•

AUTOFOCUS priority:

) Rotating Gobo 2

1

) Static Gobo

2

3) Rotating Gobo 1
) Animated Star Gobo

4

5) Iris

PAN - channel 30

•

peration with option InvertPan

O

Tilt conventionally represented at 35 bit and option Invert Tilt

(

G

ff

O

G

ff)

O

AUTOFOCUS ADJUSTMENT - channel 28

•

• MACRO EFFECTS - channel 29

peration with option InvertPan

O

Tilt conventionally represented at 35 bit and option Invert Tilt

(

G

n

O

G

• PAN FINE - channel 31

Operation with option InvertPan
(Tilt conventionally represented at 35 bit and option Invert TiltGOff)

G

Off

ff)

O

ALPHA SPOT HPE 1500 & ST

Operation with option InvertPanGOn
(Tilt conventionally represented at 35 bit and option Invert Tilt

40

G

Off)

BIT

255

0

SE

T
X

S
E
L

D
M
X

SE

T
X

S
E
L

D
M
X

TILT - channel 32

BIT

255

1

28

0

SE

T
X

S
E
L

D
M
X

SE

T
X

S
E
L

D
M
X

SE

T
X

S
E
L

D
M
X

B

IT

2

55

128

0

SE

T
X

S
E
L

D
M
X

SE

T
X

S
E
L

D
M
X

SE

T
X

S
E
L

D
M
X

BIT

255

0

SE

T
X

S
E
L

D
M
X

SE

T
X

S
E
L

D
M
X

BIT EFFECT

255

51-62

38-50

25-37

12-24

LINEAR (Default)

UNUSED RANGE

UNUSED RANGE

CONVENTIONAL

DIMMER CURVE
FUNCTION

FAST (Default)

NORMAL

PAN-TILT
FUNCTION

BIT EFFECT

255

128
127

77
76

26

25

0

Complete reset is activated passing
throug the unused range and staying
5 seconds in complete reset levels.

COMPLETE RESET
PAN / TILT RESET

PAN / TILT RESET
EFFECTS RESET

EFFECTS RESET

UNUSED RANGE

P

an / Tilt reset is activated passing
throug the unused range and staying
5 seconds in Pan / Tilt reset levels.

E

ffects reset is activated passing
t

hroug the unused range and staying

5

seconds in Effects reset levels.

COMPLETE RESET

LAMP ON (1500 W)

LAMP ON (1500 W)

BIT

EFFECT

255

180

0

101
100

LAMP OFF

179

26

LAMP OFF

25

UNUSED RANGE

Lamp ignition after 5 s
in full power levels.

Lamp switch off passing
throug the unused
range and staying 5 s in
Lamp OFF levels.

LAMP ON (1200 W)

LAMP ON (1200 W)

Immediate transition
from full to half power.

Immediate transition
from half to full power.

Lamp ignition not allowed
in half power.

ON

ON

ON

OFF

ON

OFF

•

Operation with option Invert Tilt
(Pan conventionally represented at 0 bit and option Invert PanGOff)

G

Off

FUNCTION - channel: 34

•

The functions are actived passing through unused range and staying 5 seconds in

ecessary level.

n

Operation with option Invert TiltGOn

Pan conventionally represented at 0 bit and option Invert Pan

(

• TILT FINE - channel 33

Operation with option Invert Tilt
(Pan conventionally represented at 0 bit and option Invert Pan

G

Off

G

G

O

Off)

• RESET - channel: 35

ff)

The functions are actived passing through unused range and staying 5 seconds in
necessary level.

•

LAMP CONTROL (only with option LAMP DMX On) - channel: 36

IMPORTANT: Alpha Spot HPE 1500 is not provided with hot restrike igniter

Operation with option Invert TiltGOn
(Pan conventionally represented at 0 bit and option Invert Pan

ALPHA SPOT HPE 1500 & ST

G

Off)

The functions are actived passing through unused range and staying 5 seconds in
necessary level.

41

Continue

➔

TIMING CHANNELS

Timing Channel Channel function

37 Pan - Tilt time Pan – Tilt – Pan Fine – Tilt Fine
38 Colour time Cyan - Magenta - Yellow – C.T.O. – Color wheel
39 Beam time Dimmer - Iris -Focus effects movment - Focus - Zoom - Frost – Rotating Prism change – Frost insertion

40 Gobo time Gobo Fix - Rotating Gobo 1/2 change – Animation Disk insertion

TIME TABLE

BIT Seconds

0 Full
1 0.2
2 0.4
3 0.6
4 0.8
5 1
6 1.2
7 1.4
8 1.6
9 1.8
10 2
11 2.2
12 2.4
13 2.6
14 2.8
15 3
16 3.2
17 3.4
18 3.6
19 3.8
20 4
21 4.2
22 4.4
23 4.6
24 4.8
25 5
26 5.2
27 5.4
28 5.6
29 5.8
30 6
31 6.2
32 6.4
33 6.6
34 6.8
35 7
36 7.2
37 7.4
38 7.6
39 7.8
40 8
41 8.2
42 8.4

BIT Seconds

43 8.6
44 8.8
45 9
46 9.2
47 9.4
48 9.6
49 9.8
50 10
51 10.2
52 10.4
53 10.6
54
55
56
57
58
59

11

12

13

60
61 14
62
63
64

15

65
66 16
67
68
69

17

70
71 18
72
73
74

19

75
76 20
77
78
79 21
80
81
82

22

83
84 23
85

BIT Seconds

86
87

24

88
89 25
90
91
92

26

93
94 27
95
96
97

28

98
99 29
100
101
102 30
103
104
105

31

106
107 32
108
109
110

33

111
112 34
113
114
115

35

116
117 36
118
119
120

37

121
122 38
123
124
125 39
126
127
128

40

BIT Seconds

129
130 41
131
132
133

42

134
135 43
136
137
138

44

139
140 45
141
142
143

46

144
145 47
146
147
148

48

149
150 49
151
152
153 50
154
155
156

51

157
158 52
159
160
161

53

162
163 54
164
165
166

55

167
168 56
169
170
171

57

BIT Seconds

172
173 58
174
175
176 59
177
178
179

60

180
181 65
182
183
184

70

185
186 75
187
188
189

80

190
191 85
192
193
194

90

195
196 95
197
198
199

100

200
201 110
202
203
204 120
205
206
207

130

208
209 140
210
211
212

150

213
214 160
215

BIT Seconds

216
217

170

218
219 180
220
221
222

190

223
224 200
225
226
227 210
228
229
230

220

231
232 230
233
234
235

240

236
237 250
238
239
240

260

241
242 270
243
244
245

280

246
247 290
248
249
250

300

251
252
253

310

254

Follow cue

255

Data

ALPHA SPOT HPE 1500 & ST

42

CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. [phone] - Fax [phone] - www.claypaky.it

IST00C/001 – EN - Rev.C 05/2015