Clay Paky alpha profile 1500, alpha profile 1500 ""q Instruction Manual

Download

Page 1

ALPHA PROFILE 1500

ALPHA PROFILE 1500 "Q"

C61330

C61335

INSTRUCTION MANUAL

INDEX

Pag.

Congratulations on choosing a Clay Paky product! We thank you for your custom. Please note that this product, as all the others in the rich Clay Paky range, has been designed and made with total quality to ensure excellent performance and best meet your expectations and requirements.

Carefully read this instruction manual in its entirety and keep it safe for future reference. It is essential to know the information and comply with the instructions given in this manual to ensure the fitting is installed, used and serviced correctly and safely. CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to other property or persons deriving from installation, use and maintenance that have not been carried out in conformity with this instruction manual, which must always accompany the fitting. CLAY PAKY S.p.A. reserves the right to modify the characteristics stated in this instruction manual at any time and without prior notice.

Contents

Safety information

Unpacking and preparation

Installation and start-up

Control panel

Menu setting

Maintenance

Technical information

Cause and solution of problems

Channel functions

ENGLISH

Page 2

ALPHA PROFILE 1500

• Installation

Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used, it needs to be replaced with a genuine spare.

• Minimum distance of illuminated objects

The projector needs to be positioned so that the objects hit by the beam of light are at least 5 metres (16'5'') from the lens of the projector.

• Minimum distance from flammable materials

The projector must be positioned so that any flammable materials are at least 0.20 metres (8") from every point on the surface of the fitting.

• Mounting surfaces

It is permissible to mount the fitting on normally flammable surfaces.

• Maximum ambient temperature

Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

• IP20 protection rating

The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0).

• Protection against electrical shock

Connection must be made to a power supply system fitted with efficient earthing (Class I appliance according to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the projectors from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• Connection to mains supply

Connection to the electricity mains must be carried out by a qualified electrical installer. Check that the mains frequency and voltage correspond to those for which the projector is designed as given on the electrical data label. This label also gives the input power to which you need to refer to evaluate the maximum number of fittings to connect to the electricity line, in order to avoid overloading.

• Temperature of the external surface

The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is 150°C (302°F).

• Maintenance

Before starting any maintenance work or cleaning the projector, cut off power from the mains supply. After switching off, do not remove any parts of the fitting for at least 10 minutes. After this time the likelihood of the lamp exploding is virtually nill. If it is necessary to replace the lamp, wait for another 20 minutes to avoid getting burnt. The fitting is designed to hold in any splinters produced by a lamp exploding. The lenses must be mounted and, if visibly damaged, they have to be replaced with genuine spares.

• Lamp

The fitting mounts a high-pressure lamp that needs an external igniter. This igniter is fitted onto the apparatus.

- Carefully read the "operating instructions" provided by the lamp manufacturer.

- Immediately replace the lamp if damaged or deformed by heat.

• Battery

This product contains a rechargeable lead-acid battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. Instructions on how to remove the battery from the product are available on www.claypaky.it

SAFETY INFORMATION

The products referred to in this manual conform to the European Community Directives to which they are subject:

• Low Voltage 2006/95/CE

• Electromagnetic Compatibility 2004/108/CE

1500W

IP20

Page 3

ALPHA PROFILE 1500

UNPACKING AND PREPARATION

Lamp 1500W

(fitted into projector)

099106

2 x 183102/802

90°

LOCKED

UNLOCKED

PAN Mechanism Lock and Release (every 90°) - Fig. 2

TILT Mechanism Lock and Release (every 45°) - Fig. 3

45°

UNLOCKED

LOCKED

Packing contents - Fig. 1

Page 4

ALPHA PROFILE 1500

INSTALLATION AND START-UP

Connecting and disconnecting power cable - Fig. 5

Installing the projector - Fig. 4

The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.

WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.

Page 5

ALPHA PROFILE 1500

CONTROL PANEL

Continue

➔

Switching on the projector - Fig. 8 Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:

Model Firmware xxx (Fixture ID) System errors

Alpha PROFILE Version X.X.X Dmx Address xxx E: .........................

1500 Date - Hour W: .........................

On conclusion of resetting in case of absence of dmx signal, Pan and Tilt move to the “Home” position (Pan 50% - Tilt 50%). The control panel (Fig.

8) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions: rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set). During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status. It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the

key will be cancelled.

Dmx Address

Warning Message

Fixture ID

MAINS

Connecting to the control signal line (DMX) - Fig. 7 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3. IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.

SIGNAL

SCREEN

DMX 512

5 PIN

SIGNAL

SCREEN

DMX 512

3 PIN

SIGNAL

DMX 512

Connecting to the mains supply - Fig. 6

Mains

Page 6

ALPHA PROFILE 1500

Reversal of the display - Fig. 9 To activate this function, press UP

and DOWN Ckeys simultaneously while the display is in the rest mode. This status will be memorised and

maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.

Setting the projector starting address

On each projector, the starting address must be set for the control signal (addresses from 1 to 512). The address can also be set with the projector switched off. Setting the address: see pag. 8.

Setting the projector Fixture ID

On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255). The Fixture ID address can be set with the projector switched off. Setting the Fixture ID: see pag. 8.

Functions of the buttons - Using the menu

Setting addresses and options with the projector disconnected

The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply. All that is needed is to press

to momentarily activate the display and thus access the settings. Once the required operations have been carried out,

the display will switch off again after a wait time of 30 seconds.

USING THE MENU:

1) Press

once – “Main Menu” appears on the display.

2) Use the UP

and DOWN Ckeys to select the menu to be used:

• Setup (Setup Menu): To set the setting options.

• Option (Option Menu): To set the operating options.

• Informations (Informations Menu): To read the counters, software version and other information.

• Manual Control (Manual control Menu): To trigger the test and manual control functions.

• Test (Test Menu): To check the proper functionning of effects.

• Advanced (Advanced Menu): Access to the “Advanced menu” is recommended for a trained technical personnel. To enable the “Advanced” see pag.14

3) Press

to display the first item in the selected menu.

4) Use the UP

and DOWN Ckeys to select the MENU items.

Confirms the displayed value, or activates the displayed function, or enters the successive menu.

Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.

Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.

Return to the top level

Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù.

DOWN

LEFT

RIGHT

Page 7

ALPHA PROFILE 1500

System

Errors

Information

Fixture

Hours

Lamp Hours

MENU SETTING

Set Up

Option

Information

anual

ontrol

Test

Advanced

Lamp

Strikes

System Version

Board

diagnostic

Dmx

Monitor

Fans

Monitor

Network

parameters

Continue

➔

Lamp

Manual Control

Reset

Channel

Access code

1234

Advanced

Calibration

Upload

Firmware

Setup Model

Pan / Tilt

Colour

Beam

Gobo

All

Test

Lamp Dmx

Pan / Tilt

Color

Option

Invert

Pan

Invert

Tilt

Swap

Pan-Tilt

Encoder

Pan-Tilt

Color

Mixing

Fixed Wheel

Shortcut

Macro Color

Adjustment

Shutter

On Error

Dimmer On

Shutter

Autofocus

Mode

Limited Zoom

Range

Complete

Zoom Range

Macro

Effects

Macro group

size

Macro

fixture Id

Silent Mode

Standard

Quiet

Power Mode

1500-1200

Full fan speed

1200

Low fan speed

1500-1200

Auto fan speed

Display

Setting

Default

Preset

User

Preset 1

User

Preset 2

User

Preset 3

Dmx

Address

Channel

Mode

Ethernet Interface

Fixture ID

Page 8

ALPHA PROFILE 1500

DMX ADDRESS NOTE: without the DMX signal the Address (XXX) flashing

Allows you to select the DMX ADDRESS

1) Press

- the current DMX Adress appear on the display.

2) Use the UP

, DOWN C, RIGHT Ekeys to plan the DMX

Address.

3) Press

to confirm the selection or LEFT Dto keep current settings.

CHANNEL MODE

Allows you to select a channel arrangement from the two available.

1) Press

- the current settings appear on the display (Standard or

Vector).

2) Use the UP

and DOWN Ckeys to select one of the following

settings:

- Standard

- Vector

3) Press

to confirm the selection or LEFT Dto keep current settings.

FIXTURE ID

Allows you to select the FIXTURE ID

1) Press

- the current Fixture ID appear on the display.

2) Use the UP

, DOWN C, RIGHT Ekeys to plan the Fixture ID.

3) Press

to confirm the selection or LEFT Dto keep current settings.

ETHERNET INTERFACE

It lets you set the Ethernet settings to be attributed to the projector.

1) Premere

2) Use the UP

and DOWN Ckeys to select the “Ethernet Interface”

options to set:

Control Protocol

It lets you select the “Control Protocol” Art-net to assign according to the control unit used:

1) Press

the current setting appears on the display.

2) Use the UP

and DOWN Ckeys to select one of the following settings:

- Disabled

- Art-net on IP 2

- Art-net on IP 10

3) Press

to confirm the selection or LEFT Dto keep the current setting.

Repeat on DMX

It lets you enable the transmission of the Ethernet protocol by DMX signal to all the connected projectors.

1) Press

the current setting appears on the display.

2) Use the UP

and DOWN Ckeys to select one of the following settings:

- Disabled: DMX transmission disabled.

- Enabled on primary: DMX transmission enabled.

3) Press

to confirm the selection or LEFT Dto keep the current setting.

Universe

It lets you assign the “Universe” number to be assigned to a series of projectors.

1) Press

– the current Universe address appears on the display.

2) Use the UP

, DOWN C, RIGHT Ekeys to set the Universe address.

3) Press

to confirm the selection or LEFT Dto keep the current setting.

SET UP MENU

Set Up

Dmx

Address

Channel

Mode

Fixture Id

Address xxx

Standard

Vector

alue xxx

Ethernet Interface

Control

Protocol

Repeat on

DMX

Universe

NOTE: On grey the default options

Page 9

ALPHA PROFILE 1500

Continue

➔

LAMP DMX

Used for enabling lamp remote control channel.

1) Press

- the current settings appear on the display (On or Off).

2) Use the UP

and DOWN Ckeys to enable (On) or disable (Off)

the lamp remote control channel.

3) Press

to confirm the selection or LEFT Dto keep current settings.

PAN / TILT Invert pan

Used for reversing Pan movement.

1) Press

- the current settings appear on the display (On or Off).

2) Use the UP

and DOWN Ckeys to enable (On) or disable (Off)

PAN inversion.

3) Press

to confirm the selection or LEFT Dto keep current settings.

Invert tilt

Used for reversing tilt movement.

1) Press

- the current settings appear on the display (On or Off).

2) Use the UP

and DOWN Ckeys to enable (On) or disable (Off)

Tilt inversion.

3) Press

to confirm the selection or LEFT Dto keep current settings.

Swap Pan-Tilt

Used for swapping Pan and Tilt channels (as well as Pan fine and Tilt fine).

1) Press

- the current settings appear on the display (On or Off).

2) Use the UP

and DOWN Ckeys to enable (On) or disable (Off)

Pan and Tilt channel swap.

3) Press

to confirm the selection or LEFT Dtto keep current settings.

Encoder Pan-Tilt

Used for enabling the Pan / Tilt encoders.

1) Press

- the current settings appear on the display (On or Off).

2) Use the UP

and DOWN Ckeys to enable (On) or disable (Off)

Pan / Tilt encoders.

3) Press

to confirm the selection or LEFT Dto keep current settings.

COLOR Color mixing

Used for reversing the CMY color mixing system.

1) Press

- the current settings appear on the display (On or Off).

2) Use the UP

and DOWN Ckeys select one of the following settings:

RGB color mixing mode CMY color mixing mode

3) Press

to confirm the selection or LEFT Dto keep current settings.

Fixed wheel short-cut

Used for optimizing color change time so that the disc turns in the direction that requires shorter movement.

1) Press

– the current settings appear on the display (On or Off).

2) Use the UP

and DOWN Ckeys to enable (On) or disable (Off)

color change optimization.

3) Press

to confirm the selection, or LEFTDto keep current settings.

Macro color adjustment

It lets you enable the overwriting of a “Macro Colour” with the Cyan, Magenta, Yellow, CTO and Colour wheel channels. Press

the current setting appears on the display.

1) Use the UP

and DOWN Ckeys to enable (On) or disable (Off)

the overwriting.

2) Press

to confirm the selection or LEFT Dto keep the current setting.

Color

Swap

Pan-Tilt

Off

Encoder

Pan-Tilt

Off

Color

Mixing

RGB

CMY

Fixwheel

Shortcut

Off

Macro Color

Adjustment

Off

OPTIONS MENU

Lamp Dmx

Pan / Tilt

Option

Off

Invert

Pan

Off

Invert

Tilt

Off

Page 10

ALPHA PROFILE 1500

Macro

Effects

Macro fixture Id

SHUTTER Shutter on error

Used for automatically closing the stop/strobe in the event of Pan/Tilt position error.

1) Press

- the current settings appear on the display (On or Off).

2) Use the UP

and DOWN Ckeys to enable (On) or disable (Off)

automatic stop/strobe closing in the event of Pan/Tilt position error.

3) Press Fto confirm the selection, or LEFT Dto keep current settings.

Dimmer on Shutter

Enables automatic closing of the dimmer when the strobe is completely closed.

1) PressF– the current settings appear on the display (On or Off).

2) Use the UP

and DOWN Ckeys to enable (On) or disable (Off)

the automatic closing of the dimmer.

3) Press

to confirm the selection or LEFT Dto keep current settings.

AUTO-FOCUS MODE

It lets you select the “Auto-focus Mode” from the two available.

1) Press

the current setting appears on the display.

2) Use the UP

and DOWN Ckeys to select one of the following settings: Limited Zoom Range: The “Autofocus” works only in the optical run that was specifically designed for the projector in question. Complete Zoom Range: The “Autofocus” also works in overrun

3) Press

to confirm the selection or LEFT Dto keep the current setting.

MACRO EFFECTS

It lets you select the “Macro Effects” from the two available.

1) Press

the current setting appears on the display.

2) Use the UP

and DOWN Ckeys to select one of the following settings:

Macro group size

It lets you set the number of projectors to be included in the macro mode operation.

1) Press

2) Use the UP B, DOWN C, RIGHT keys to set the number of projectors to be included in the “Macro Effect” operation.

3) Press

to confirm the selection or LEFT Dto keep the current setting.

Macro fixture Id

It lets you attribute an ID address to the projector for the phase displacement for the scene’s starting time in Macro mode.

1) Press

Use the UP Band DOWN Ckeys to select one of the following settings: Fixed to X. (to assign to all the projectors to be included in the Macro operation). Auto by DMX Address: According to the DMX address, it automatically detects the starting sequence of the scene in the Macro mode (to assign to all the projectors to be included in the Macro operation).

3) Press

to confirm the selection or LEFT Dto keep the current setting.

SILENT MODE

It lets you select the “Silent Mode” from the two available.

1) Press

the current setting appears on the display.

Use the UP Band DOWN Ckeys to select one of the following settings:

Standard: Maximum speed and consequently maximum effects noise level. Quiet: reduces the speed of some effects, thereby reducing their noise level.

3) Press Fto confirm the selection or LEFT Dto keep the current setting.

Macro group

size

Silent Mode

Standard

Quiet

Shutter

On Error

Off

Dimmer On

Shutter

Off

Auto-focus

Mode

Limited

Zoom Range

Complete

Zoom Range

Page 11

ALPHA PROFILE 1500

POWER MODE

Allows you to select a Power Mode from the three available.

1) Press

- the current settings appear on the display.

2) Use the UP

and DOWNCkeys to select one of the following settings:

- 1500-1200W Full fan speed: Lamp can change from full-power (1500W) to half-power (1200W) using the LAMP CONTROL channel. Fans always work at Full speed

- 1200W Low fan speed: Lamp constantly works in half-power mode (1200W) while the Fan always works at Low speed. With LAMP CONTROL channel you can only switch the lamp ON and OFF.

- 1500-1200W Auto fan speed: Lamp can change from full-power (1500W) to half-power (1200W) using the LAMP CONTROL channel. Automatically the fans switch from Full speed to Low speed respectively.

3) Press

to confirm the selection or LEFT Dto keep current setting.

DISPLAY

Used for automatically reduce brightness on the display after about 30 seconds in idle.

1) Press

- the current settings appear on the display (On or Off).

2) Use the UP

and DOWN Ckeys to enable (On) or disable (Off)

the decreasing of display brightness.

3) Press

to confirm the selection or LEFT Dto keep current

settings.

SETTING

Used to save 3 different settings of the items in the options menu and relative submenus.

1) Press

- “Default preset” appears on the display.

2) Use the UP

and DOWN Ckeys to select one of the following

configurations:

- Default preset (*)

- User preset 1

- User preset 2

- User Preset 3

3) Press

- “Load preset X” appears on the display.

4) Use the UP

and DOWN Ckeys to select:

- Load preset X to recall a previously stored configuration.

- Save to preset X to store the current configuration. a confirmation message (Are you sure?) appears on the display.

5) Select YES to confirm the selection or NO to keep the current setting and return to the next higher level.

(*) DEFAULT PRESET Used for restoring default values on all options menu items and relevant submenus.

1) Press

, a confirmation message (Are you sure?) appears on the

display.

2) Select YES to confirm the selction or NO to keep current setting.

OPTION DEFAULT Lamp DMX On Invert Pan Off Invert Tilt Off Swap Pan-Tilt Off Encoder Pan-Tilt On Colour mixing CMY Fixed Wheel Shortcut On Macro Color Adjustment On Shutter on error Off Dimmer on Shutter Off Auto-focus mode Limited zoom range Silent mode Standard Power mode 1500-1200w full fan speed Display On

Reset To

Dafault

Go Back

Setting

Default

Preset

Load

Preset 1

Save To Preset 1

User

Preset 1

Load

Preset 2

Save To Preset 2

User

Preset 2

Load

Preset 3

Save To Preset 3

User

Preset 3

Off

Display

Power Mode

1500-1200

Full fan speed

1200

Low fan speed

1500-1200

Auto fan speed

Page 12

ALPHA PROFILE 1500

Continue

➔

Lamp Hours

Total XXX Partial XXX

Reset...

Lamp

Strikes

Total XXX Partial XXX

Reset...

Information

System

Errors

Fixture

ours

Total XXX Partial XXX

Reset...

SYSTEM ERRORS

Shows a list of warnings and messages relevant to errors occurred since the fixtures switching-on.

1) Pressing Fyou are allowed to reset the SYSTEM ERRORS list. A confirmation message (Are you sure you want to clear error list ?) appears on the display.

2) Select YES to reset the list or NO to go back.

FIXTURE HOURS

Used for displaying projector operating hours (total and partial).

1) Press

- Hours total and partial appears on the display.

Total counter

Counts the number of projector working life hours (from manufacture to date).

Partial counter

Counts the number of partial projector working life hours since the last reset to date.

2) Press

to reset partial projector working hours a confirmation

message (Are you sure?) appears on the display.

3) Select YES to reset partial projectors counter or NO to keep the current setting and return to the top menu level.

LAMP HOURS

Used for displaying the lamp working hours (total and partial).

1) Press

- Hours total and partial appears on the display.

Total counter

Counts the number of projector working hours with the lamp on (from manufacture to date).

Partial counter

Counts the number of lamp working hours since the last reset to date.

2) Press

to reset partial lamp working hours, a confirmation message

(Are you sure ?) appears on the display.

3) Select YES to reset partial counter or NO to keep the current setting and return to the top menu level

LAMP STRIKES

Used for displaying the number of times the lamp was turned on (total and partial).

1) Press

- the number of times the lamp was turned on (total and

partial) appears on the display.

Total counter

Counts the number of times the lamp was turned on (from manufacture to date).

Partial counter

Counts the number of times the lamp was turned on since the last reset to date.

2) Press

to reset partial lamp strikes hours, a confirmation message

(Are you sure ?) appears on the display.

3) Select YES to reset partial counter or NO to keep the current setting and return to the top menu level

SISTEM VERSION

Used for displaying the software and hardware version of each board installed in the projector. CPU brd (CPU board) 0: PT-3f (Pan / Tilt board) 1: 8-Ch (8 channel board) 2: 6-Ch (6 channel board) 3: 8-Ch (8 channel board) 4: 6-Ch (6 channel board)

INFORMATION MENU

System

Version

Board Revis. Hw.rv. CPU brd x.x.x x.x com.dev x.x 0: PT-3f x.x x.x 1: 8-Ch x.x x.x 2: 6-Ch x.x x.x 3: 8-Ch x.x. x.x 4: 6-Ch x.x. x.x

Page 13

ALPHA PROFILE 1500

BOARD DIAGNOSTIC

Used for displaying the status error of each board installed in the projector: 0: PT-3f (Pan / Tilt board) 1: 8-Ch (8 channel board) 2: 6-Ch (6 channel board) 3: 8-Ch (8 channel board) 4: 6-Ch (6 channel board)

DMX MONITOR

Used for displaying the projector DMX channel level in bit (Val) and in percentage (Perc).

FANS MONITOR

Used for displaying the speed of each fan installed in the projector: Pwr.Sup (Power supply Fan) Ball. IN (Ballast IN Fan) Ball. Out (Ballast OUT Fan) Eff.IN (Effects IN Fan) Eff.OUT (Effects OUT Fan) Lamp (Lamp Fan) Lamp (Lamp Fan) Gobo (Gobo Fan) Board (Yoke Board Fan)

NETWORK PARAMS

Allows the "Network" parameters of the projector to be displayed or:

IP address: Internet Protocol address (two projectors must not have the same IP address)

IP mask: Mac address: Media Access Control: the projector’s Ethernet Address.

LAMP

Used for turning lamp on and off from the projector control panel.

1) Pres

s F-

the current settings appear on the display (On or Off).

2) Use the

UP Band DOWN Ckeys to turn the lamp on (On) or off (Off)

3) Press

to confirm the selection or

LEFT Dto keep current settings

and return to the top level.

RESET

Used for resetting the projector.

1) Press

to reset the projectors, a confirmation message (Are you sure ?)

appears on the display.

2) Select YES to starting reset the fixture or NO to keep the current setting and return to the top menu level.

CHANNEL

Used for setting channel levels from the projector control panel.

1) Press

- the first channel appears on the display.

2) Use the UP

and DOWN Ckeys to select the required channel:

3) Press

and use the UP Band DOWN Ckeys to select the

required DMX level (value between 0 and 255).

4) Press LEFT

to return to the top menu level.

Channel

MANUAL CONTROL

Lamp

Manual Control

Off

Yes

Reset

Fans

Monitor

Fan Speed (RPM) Pwr.Sup XXXX Ball.In. XXXX Ball.Out XXXX Eff.In XXXX Eff.Out XXXX Lamp XXXX Lamp XXXX Gobo XXXX Board XXXX

Board

Diagnost.

Dmx

Monitor

Board Status Err% 0:PT-3f Good 0.00 1:8-Ch Good 0.00 2:6-Ch Good 0.00 3:8-Ch Good 0.00 4:6-Ch Good 0.00

Network

params

Page 14

ALPHA PROFILE 1500

To enable the "Advanced Menu" set up the "Access code" (1234) using the UP

, DOWN C, RIGHT Ekeys.

Press

- "Menu advanced" appears on the display

UPLOAD FIRMWARE

Allows you to transfer the firmware from 1 fixture to all the connected fixtures.

1) Press

, a confirmation message appears on the display.

2) Select YES to start the firmware loading or NO to keep the current setting and return to the top menu level

SETUP MODEL

Allows you to change the default model of projector.

1) Press

a confirmation message appears on the display.

2) Select YES to define the model of projector or NO to keep the current setting and return to the top menu level.

CALIBRATION

Allows you to adjust effects from the control panel to obtain perfect uniformity between the projectors.

1) Press

- “channels” appears on the display.

2) Using the UP

and DOWN Ckeys, select the effect you wish to

regulate.

3) Press

and use the RIGHT E, UPBand DOWN Cbuttons to

make the adjustment by setting a value between 0 and 255.

4) Press

to confirm the selection

LEFT Dto keep current set-

tings and return to the top level.

FACTORY DEFAULT

Allows you to restore default values of all channels (128).

1) Press

– a confirmation message appears on the display (Reset

calibration to factory default ?).

2) Select YES to reset calibration to factory default or NO to keep the current setting and return to the top menu level.

ADVANCED MENU

Advanced

Code

1234

Calibration

Factory

Default

Upload

Firmware

Transfer the firmware on all the connected fixtures ? Are you sure ? Yes/No

Setup

Model

Changing to a wrong model may damage the fixture. Are you sure ? Yes/No

AUTOTEST

Allows you to check the proper functioning of effects.

1) Press

2) Use the UP

and DOWN Ckeys to select the required test.

3) Press

to confirm the selection or LEFT Dto return to the top

menu level.

Test sequence: Pan - Tilt effects (Pan & Tilt) Colour effects (CMY, colour wheel, CTO) Beam effects (Stopper-Strobe / Dimmer / Iris / Prism / Frost, Focus, Zoom, Animation disk) Gobo effects (Fixed gobo / Rotating gobo) All effects

Test

Pan-Tilt Colour Beam Gobo All

TEST MENU

Page 15

ALPHA PROFILE 1500

Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section. Opening the head covers - Fig. 11.

Closing the head covers - Fig. 12.

1/4 Turn

11 12

MAINTENANCE

Page 16

ALPHA PROFILE 1500

Fan support plate opening and closing (Lower side) - Fig. 16

Lower Side

Lamp change - Fig 14 Take the new lamp out of its package and insert in the fitting.

WARNING: do not touch the lamp’s envelope with bare hands. Should this happen, clean the bulb with a cloth soaked in alcohol and dry it with a clean, dry cloth.

Lamp regulation - Fig. 15 To centre the lamp, turn the three adjusting screws as shown in the figure.

Opening and closing lamp compartment - Fig. 13

Page 17

ALPHA PROFILE 1500

Fan support plate opening and closing (Upper side) - Fig. 17

Upper Side

085911/001

085901/001

085903/001

085907/001

085912/001

085906/001

085904/001

085908/001

Lower Side

Replacing fixed gobos (ø 31.5 mm - max 25 mm image - thickness max 1 mm) - Fig. 18 IMPORTANT: Please contact CLAY PAKY before using customized gobos.

Continue

➔

Page 18

ALPHA PROFILE 1500

Lower Side

GOBO ROTATION

084632/001

105115/802

084626/001

084628/001

084630/001 084625/001

GOBO INDEX

To determine which side of a godo is coated, hold an odject up to it. On the uncoated side, there is a space between the object and its reflection.

Grey/Black side away from lamp

Reflective side

towards lamp

Coated side

towards lamp

Coated side

Uncoated side

COATED GLASS GOBOS TYPE 1 COATED GLASS GOBOS TYPE 2

Gobo orientation - Fig. 21

The pictures shown the correct gobos orientation.

Replacing rotating gobos (ø 37.5 mm - max 25 mm image – thickness 1 mm) - Fig. 20 IMPORTANT: Please contact CLAY PAKY before using customized gobos.

Bearing group replacement - Fig. 19

Page 19

ALPHA PROFILE 1500

Periodical cleaning - Fig. 22 To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.). Use a soft cloth dampened with any detergent liquid for cleaning glass to remove the dirt from the reflectors, from the lenses and filters. It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:

• General cleaning of internal parts.

• Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Clay Paky.

• General visual check of the internal components, cabling, mechanical parts, etc.

• Electrical, photometric and functional checks; eventual repairs.

Upper Side Lower Side

Continue

➔

Page 20

ALPHA PROFILE 1500

Extraction of the effect modules: Preliminary operations - Fig. 23

Thermostat

Lower Side

Page 21

ALPHA PROFILE 1500

Extraction of the effect modules - Fig. 24 IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 24 and 25 in reverse order

Lower Side

Upper Side

Continue

➔

Page 22

ALPHA PROFILE 1500

Extraction of the effect modules - Fig 25 IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 24 and 25 in reverse order

Lower Side

Upper Side

Page 23

ALPHA PROFILE 1500

488

(19.21")

232

(9.13")

500

(19.69")

480

(18.90")

660

(25.98")

628

(24.72")

843

(33.19")

740

(29.13")

Power supplies available

200-240V 50/60Hz

Input power

•

2000VA a 230V 50Hz.

Lamp

Discharge lamp.

• Type HTI 1500W/60/P50-L Lok-it Osram (L10102)

- Cap PGJ50

- Colour temperature 6000 K

- Luminous flux 135000 lm

- Average life 750 h

- Any working position

Motors

31 stepper motors, operating with microsteps, totally microprocessor controlled.

Optical unit

•

Elliptic reflector with high luminous efficiency

Channels

Max 41 control channels.

Inputs

•

DMX 512

Movable body

•

Movement by means of two stepper motors, controlled by microprocessor.

•

Automatic repositioning of PAN and TILT after accidental movement not controlled by control unit.

•

Travel:

- PAN = 540°

- TILT = 252°

•

Maximum speeds:

- PAN = 4.0 sec (360°)

- TILT = 3.2 sec (252°)

•

Resolution:

- PAN = 2.11°

- PAN FINE = 0.008°

- TILT = 0.98°

- TILT FINE = 0.004°

IP20 protection rating

• Protected against the entry of solid bodies larger than 12mm (0.47”).

• No protection against the entry of liquids.

CE Marking

In conformity with the European Union Low Voltage Directive 2006/95/CE and Electromagnetic compatibility Directive 2004/108/CE.

Safety Devices

• Bipolar circuit breaker with thermal protection.

• Automatic break in power supply in case of overheating or failed operation of cooling system.

Cooling

Forced ventilation with axial fans.

Body

• Aluminium structure with die-cast plastic cover.

• Two side handles for transportation.

• Device locking PAN and TILT mechanisms for transportation and maintenance.

Working position

Functioning in any position.

Weights

about 50.35 Kg (110lbs, 12ozs).

TECHNICAL INFORMATION

CAUSE AND SOLUTION OF PROBLEMS

THE PROJECTOR WILL NOT SWITCH ON

PROBLEMS

ELECTRONICS NON-OPERATIONAL

DEFECTIVE PROJECTION

REDUCED LUMINOSITY

POSSIBLE CAUSES CHECKS AND REMEDIES

No mains supply. Lamp exhausted or defective. Signal transmission cable faulty or disconnected. Incorrect addressing. Fault in the electronic circuits. Lenses or reflector broken Dust or grease deposited.

Check the power supply voltage. Replace the lamp. (See instructions). Replace the cables. Check addresses (see instructions). Call an authorised technician. Call an authorised technician. Clean (see instructions).

Page 24

ALPHA PROFILE 1500

CHANNEL FUNCTION

CHANNEL

STANDARD VECTOR

CHANNEL MODE

CYAN

MAGENTA

YELLOW

C.T.O

COLOUR WHEEL

MACRO COLOURS

STOP/STROBE

DIMMER

DIMMER FINE

IRIS

STATIC GOBO CHANGE

ROTATING GOBO CHANGE

GOBO ROTATION

GOBO FINE

ROTATING PRISM CHANGE

PRISM ROTATION

FROST INSERTION

BLADE UP1

BLADE UP2

BLADE DW1

BLADE DW2

BLADE RG1

BLADE RG2

BLADE LF1

BLADE LF2

FRAMING ROTATION

FOCUS

FOCUS FINE

ZOOM

AUTOFOCUS DISTANCE

AUTOFOCUS ADJUSTMENT

MACRO EFFECTS

PAN

PAN FINE

TILT

TILT FINE

FUNCTION

RESET

LAMP CONTROL (with Option "Lamp DMX" ON)

CYAN

MAGENTA

YELLOW

C.T.O

COLOUR WHEEL

MACRO COLOURS

STOP/STROBE

DIMMER

DIMMER FINE

IRIS

STATIC GOBO CHANGE

ROTATING GOBO CHANGE

GOBO ROTATION

GOBO FINE

ROTATING PRISM CHANGE

PRISM ROTATION

FROST INSERTION

BLADE UP1

BLADE UP2

BLADE DW1

BLADE DW2

BLADE RG1

BLADE RG2

BLADE LF1

BLADE LF2

FRAMING ROTATION

FOCUS

FOCUS FINE

ZOOM

AUTOFOCUS DISTANCE

AUTOFOCUS ADJUSTMENT

MACRO EFFECTS

PAN

PAN FINE

TILT

TILT FINE

FUNCTION

RESET

LAMP CONTROL (with Option "Lamp DMX" ON)

PAN-TILT TIME

COLOUR TIME

BEAM TIME

GOBO TIME

Page 25

ALPHA PROFILE 1500

BIT % EFFECT

255 100

COLOUR EXCLUDED

0 0.0

COLOUR INSERTED

CHANNEL 1

CYAN

CHANNEL 2

MAGENTA

CHANNEL 3

YELLOW

BIT % EFFECT

255 100

COLOUR INSERTED

00.0

COLOUR EXCLUDED

CHANNEL 1

CYAN

CHANNEL 2

MAGENTA

CHANNEL 3

YELLOW

• COLOUR MIXING - channel 1 - 2 - 3

Operation with option color mixing: RGB

Operation with option color mixing: CMY

IMPORTANT: The lamp dim to half power 1 second after all the 3 channels stay at 100% level. The lamp goes back to full power when the channels level is put lower than 100%.

IMPORTANT: The lamp dim to half power 1 second after all the 3 channels stay at 0% level. The lamp goes back to full power when the channels level is put higher than 0%.

• C.T.O. - channel 4

BIT % EFFECT

0 0.0

FILTER EXCLUDED

255 100

FILTER INSERTED

CHANNEL 4

CTO

• COLOUR WHEEL - channel 5

BIT % EFFECT

255 100

FAST ROTATION 160 rpm

128050.0

0.0

SLOW ROTATION 0.2rpm

BLUE

ORANGE

AQUAMARINE

GREEN

PINK

RED

WHITE

46.0

38.0

30.0

23.0

15.0

8.0

117

NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 50% - Tilt 50%) all the others channels stay at 0%.

• MACRO COLOURS - channel 6

Continue

➔

COLOR NAME BIT % ROSCO LEE CYAN

MAGENTA

YELLOW CTO WHEEL

CODE CODE BIT BIT BIT BIT BIT

Unused Range 148-255 58,0-100 - - - - - - -

Half CT straw 146-147 57,0-57,5 442 442 0 0 34 190 0

Lighter blue 144-145 56,2-56,7 353 353 226 0 149 138 0

Glacier blue 142-143 55,5-56,0 352 352 220 0 129 138 0

Fuschia pink 140-141 54,7-55,0 345 345 109 186 77 120 0

Mallard green 138-139 54,0-54,2 325 325 255 0 0 236 58

Jade 136-137 53,2-53,7 323 323 127 0 162 0 77

3/4 CT Orange 134-135 52,5-53,0 285 285 0 36 61 217 0

3/4 CTB 132-133 51,7-52,0 281 281 85 79 87 54 0

Half minus green 130-131 51,0-51,2 248 248 60 19 86 75 39

Minus green 128-129 50,0-50,5 247 247 60 71 86 75 39

1/4 CTO 126-127 49,5-49,7 206 206 62 71 123 122 0

1/2 CTO 124-125 48,7-49,0 205 205 25 26 45 131 0

Full CT Orange 122-123 48,0-48,2 204 204 0 44 58 234 0

1/4 CTB 120-121 47,0-47,5 203 203 75 54 91 109 0

1/2 CTB 118-119 46,2-46,7 202 202 85 71 84 89 0

Full CTB 116-117 45,5-46,0 201 201 94 79 80 0 0

Alice Blue 114-115 44,7-45,0 197 197 236 51 0 205 0

Congo Blue 112-113 44,0-44,2 181 181 251 241 0 255 0

Dark Lavender 110-111 43,2-43,7 180 180 195 170 0 160 0

Chrome Orange 108-109 42,5-43,0 179 179 0 98 255 255 0

Lagoon blue 106-107 41,7-42,0 172 172 224 0 121 40 79

Deep Lavender 104-105 41,0-41,2 170 170 100 129 77 120 0

Liliac tint 102-103 40,0-40,5 169 169 41 59 39 120 0

Daylight Blue 100-101 39,0-39,5 165 165 210 73 105 88 0

Flame red 98-99 38,2-38,7 164 164 0 255 227 255 97

Bastard amber 96-97 37,5-38,0 162 162 0 26 0 199 0

Deep Orange 94-95 36,7-37,0 158 158 0 148 255 255 0

Pink 92-93 36,0-36,2 157 157 0 159 0 255 0

Pale rose 90-91 35,0-35,5 154 154 0 48 0 189 0

Pale Gold 88-89 34,2-34,7 152 152 0 60 98 138 0

Bright rose 86-87 33,7-34,0 148 148 0 255 0 255 0

Apricot 84-85 33,0-33,2 147 147 0 81 55 255 0

Bright Blue 82-83 32,0-32,5 141 141 182 0 99 92 77

Primary green 80-81 31,2-31,7 139 139 0 0 0 231 58

Light green 78-79 30,5-31,0 121 121 0 0 255 0 77

Pale green 76-77 29,7-30,0 138 138 105 0 179 100 0

Special Lavender 74-75 29,0-29,5 137 137 97 105 72 90 0

Pale Lavender 72-73 28,2-28,7 136 136 73 102 44 120 0

Deep golden amber 70-71 27,5-28,0 135 135 0 255 255 255 0

Golden amber 68-69 26,7-27,0 134 134 0 142 234 110 0

Medium blue 66-67 26,0-26,2 132 132 255 152 127 0 77

Marine blue 64-65 25,0-25,5 131 131 60 0 106 73 77

Bright pink 62-63 24,2-24,7 128 128 0 255 0 197 0

Mauve 60-61 23,7-24,0 126 126 0 255 0 255 74

Fern Green 58-59 23,0-23,2 122 122 173 0 235 89 0

Leaf green 56-57 22,0-22,5 121 121 136 0 241 64 0

Deep Blue 54-55 21,2-21,7 120 120 255 229 58 128 77

Dark blue 52-53 20,5-21,0 119 119 255 161 0 0 77

Light blue 50-51 19,5-20,0 118 118 245 0 145 138 0

Steel blue 48-49 18,7-19,0 117 117 167 0 141 165 0

Medium blue green 46-47 18,0-18,2 116 116 189 0 157 91 77

Peacock blue 44-45 17,0-17,5 115 115 136 0 128 91 77

Dark pink 42-43 16,2-16,7 111 111 0 139 0 220 0

Light Salmon 40-41 15,5-16,0 109 109 50 121 58 230 0

English rose 38-39 14,7-15,0 108 108 0 62 0 247 0

Light rose 36-37 14,0-14,2 107 107 0 95 0 220 0

Primary red 34-35 13,2-13,7 106 182 0 0 0 0 20

Orange 32-33 12,5-13,0 105 105 0 182 255 76 0

Deep amber 30-31 11,7-12,0 104 104 0 26 199 223 0

Straw 28-29 11,0-11,2 103 103 58 17 104 176 0

Light amber 26-27 10,0-10,5 102 102 0 0 171 193 0

Yellow 24-25 9,5-9,7 101 101 0 0 255 149 0

Spring yellow 22-23 8,7-9,0 100 100 80 0 227 157 0

Dark Yellow Green 20-21 8,0-8,2 90 90 255 0 255 204 0

Lime green 18-19 7,0-7,5 88 88 118 0 241 124 0

Just Blue 16-17 6,2-6,7 79 79 255 77 0 204 0

Tokyo Blue 14-15 5,5-6,0 71 71 255 255 0 180 77

Sky blue 12-13 4,7-5,0 068 068 245 77 64 173 0

Pale blue 10-11 4,0-4,2 063 063 122 0 112 127 0

Lavender 8-9 3,2-3,7 058 058 165 186 77 0 0

Bright Red 6-7 2,5-3,0 026 026 0 255 0 255 21

Med Yellow 4-5 1,7-2,0 010 010 48 0 239 115 0

Med bastard amber 2-3 1,0-1,2 004 004 0 62 78 159 0

Random Macro Color

(only for Macro effects)

10,5-------

Unused Range 0 0,0 - - - - - - -

Page 26

ALPHA PROFILE 1500

• DIMMER FINE - channel 9

BIT % EFFECT

255 100

0 0.0

• STATIC GOBO CHANGE - channel 11

GOBO 8 SHAKE, FAST SPEED

GOBO 8 SHAKE, SLOW SPEED GOBO 7 SHAKE, FAST SPEED

GOBO 7 SHAKE, SLOW SPEED GOBO 6 SHAKE, FAST SPEED

GOBO 6 SHAKE, SLOW SPEED GOBO 5 SHAKE, FAST SPEED

GOBO 5 SHAKE, SLOW SPEED GOBO 4 SHAKE, FAST SPEED

GOBO 4 SHAKE, SLOW SPEED GOBO 3 SHAKE, FAST SPEED

GOBO 3 SHAKE, SLOW SPEED GOBO 2 SHAKE, FAST SPEED

GOBO 2 SHAKE, SLOW SPEED GOBO 1 SHAKE, FAST SPEED

GOBO 1 SHAKE, SLOW SPEED FAST ROTATION (100 rpm)

SLOW ROTATION (5 rpm) STOP SLOW ROTATION (5 rpm)

FAST ROTATION (100 rpm)

GOBO 8

GOBO 7

GOBO 6

GOBO 5

GOBO 4

GOBO 3

GOBO 2

GOBO 1

WHITE

BIT % EFFECT

MACRO

255

244 243

232 231

220 219

208 207

196 195

184 183

172 171

160 159

118

114 - 117

113

64 - 71

56 - 63

48 - 55

40 - 47

32 - 39

24 - 31

16 - 23

8 - 15

0 - 7

100

95.5

95.0

91.0

90.5

86.2

86.0

81.7

81.2

76.7

76.2

72.0

71.7

67.5

67.0

63.0

62.5

46.2

44.7 - 46.0

44.2

28.2

25.0 - 28.0

22.0 - 24.7

18.7 - 21.7

15.5 - 18.2

12.5 - 15.0

9.5 - 12.0

6.2 - 9.0

3.2 - 6.0

0 - 3.0

• ROTATING GOBO CHANGE - channel 12

MACRO

GOBO 6 SHAKE, FAST SPEED

GOBO 6 SHAKE, SLOW SPEED GOBO 5 SHAKE, FAST SPEED

GOBO 5 SHAKE, SLOW SPEED GOBO 4 SHAKE, FAST SPEED

GOBO 4 SHAKE, SLOW SPEED GOBO 3 SHAKE, FAST SPEED

GOBO 3 SHAKE, SLOW SPEED GOBO 2 SHAKE, FAST SPEED

GOBO 2 SHAKE, SLOW SPEED GOBO 1 SHAKE, FAST SPEED

GOBO 1 SHAKE, SLOW SPEED GOBO 6

GOBO 5

GOBO 4

GOBO 3

GOBO 2

GOBO 1

WHITE

BIT % EFFECT

255

235 234

214 213

193 192

172 171

151 150

130

112-129

93-111

75-92

56-74

38-55

19-37

0-18

100

92.0

91.7

84.0

83.7

75.5

75.0

67.5

67.0

59.0

58.7

51.0

44.0-50.5

36.2-43.7

29.5-36.0

22.0-29.0

14.7-21.7

7.5-14.2

0-7.0

• STOP / STROBE - channel 7

IMPORTANT: The lamp dim to half power 1 second after the channel stay at 0% level.

The lamp goes back to full power when the channel level is put higher than 0%.

MACRO

BIT % EFFECT

252 - 255 98.7 - 100

OPEN

0 - 3 0.0 - 1.2

CLOSED

213 - 225 83.7 - 88.2

RANDOM SLOW STROBE

41.7

SLOW STROBE (1 flash/sec)

103 40.5

FAST STROBE (12 flash/sec)

104 - 107 41.0 - 42.0

OPEN

108 42.5

SLOW PULSATION

208 - 212 81.7 - 83.2

OPEN

226 - 238 88.7 - 93.2

RANDOM MEDIUM STROBE

239 - 251 93.7 - 98.2

RANDOM FAST STROBE

207 81.2

FAST PULSATION

The lamp is linearly dimmed from full power to half power electronicaly and mechanically from half power to off.

• DIMMER - channel 8

BIT % EFFECT

255 100

0 0.0

00.0

MINIMUM APERTURE

252 - 255 98.7 - 100

MAXIMUM APERTURE

BIT % EFFECT

251 98.2

FAST PULSATION, FAST CLOSING

212 83.2

SLOW PULSATION, FAST CLOSING

211 83

FAST PULSATION, FAST OPENING

172 67.5

SLOW PULSATION, FAST OPENING

171 67

FAST PULSATION

132 51.7

SLOW PULSATION

128 - 131 50.0 - 51.2

MAXIMUM APERTURE

MACRO

• IRIS - channel 10

Page 27

ALPHA PROFILE 1500

• PRISM INSERTION - channel 15

BIT % EFFECT

128 50.0

PRISM EXCLUDED

00.0

255 100

PRISM INSERTED

127 49.7

• PRISM ROTATION - channel 16

STOP

FAST ROTATION (120 rpm)

SLOW ROTATION (3 rph)

FAST ROTATION (120 rpm)

BIT % EFFECT

191 - 192 74.7 - 75.0

255 100

193 75.5

190 74.2

128 50.0

STOP

540

360

POSITION 540°127 49.7

POSITION 450°

105 41.7

POSITION 360°

84 33.0

POSITION 270°

63 24.7

POSITION 180°

42 16.2

00.0

POSITION 0°

POSITION 90°

21 8.2

• FROST - channel 17

BIT % EFFECT

255 100

FROST INSERTED

0 0.0

FROST EXCLUDED

BLADE IN

BIT % EFFECT

255 100

0 0.0

127 50.0

BLADE OUT

• BLADE UP 1 - channel: 18

• BLADE UP 2 - channel: 19

• BLADE DW 1 - channel: 20

BLADE IN

BIT % EFFECT

255 100

00.0

127 50.0

BLADE OUT

BLADE IN

BIT % EFFECT

255 100

00.0

127 50.0

BLADE OUT

00.0

0° POSITION

21 8.2

90° POSITION

42 16.2

180° POSITION

63 24.7

270° POSITION

84 33.0

360° POSITION

105 41.7

450° POSITION

127 49.7

540° POSITION

STOP

540°

360°

0°

255 100

FAST ROTATION (150 rpm)

193 75.5

SLOW ROTATION

(2,2 rph)

191 - 192 74.7 - 75.0

STOP

190 74.2

SLOW ROTATION

(2,2 rph)

BIT % EFFECT

128 50.0

FAST ROTATION (150 rpm)

• GOBO ROTATION - channel 13

• GOBO FINE - channel 14

BIT %

255 100

127 50.0

00.0

Continue

➔

Page 28

ALPHA PROFILE 1500

• BLADE DW 2 - channel: 21

BLADE IN

BIT % EFFECT

255 100

00.0

127 50.0

BLADE OUT

BLADE IN

BIT % EFFECT

255 100

00.0

127 50.0

BLADE OUT

BLADE IN

BIT % EFFECT

255 100

00.0

127 50.0

BLADE OUT

• BLADE RG 1 - channel: 22

• BLADE RG 2 - channel: 23

BLADE IN

BIT % EFFECT

255 100

0 0.0

127 50.0

BLADE OUT

• BLADE LF 1 - channel: 24

BLADE IN

BIT % EFFECT

255 100

0 0.0

127 50.0

BLADE OUT

• BLADE LF 2 - channel: 25

Important:

The lamp automatically dim to half power in any condition in which the blades completely shut the light beam.

• FRAMING ROTATION - channel: 26

BIT %

255 100

127 50.0

0 0.0

• FOCUS - channel 27

BIT % EFFECT

255 100

NEAR

0 0.0

DISTANT

Page 29

ALPHA PROFILE 1500

Operation with option InvertPanGOn (Tilt conventionally represented at 14% and option Invert Tilt

Off)

BIT %

255 100

00.0

BIT %

255 100

0 0.0

• PAN - channel 33

Operation with option InvertPan

Off

(Tilt conventionally represented at 14% and option Invert Tilt

Off)

• MACRO EFFECTS - channel 32

• AUTOFOCUS DISTANCE - channel 30

BIT % EFFECT

255 100

100 METRES

50 METRES

40 METRES

30 METRES

20 METRES

10 METRES

3 METRES

AUTOFOCUS OFF

128

102

0-6

50.0

40.0

30.0

20.0

10.0

3.0

0.0-2.5

• AUTOFOCUS ADJUSTMENT - channel 31

BIT % EFFECT

128 50.0

0 0.0

255 100

FOCUS FINE

AUTOFOCUS priority:

1 - Blades 2 - Rotating Gobo 3 - Static Gobo 4 - Iris

• FOCUS FINE - channel 28

BIT % EFFECT

255 100

NEAR

00.0

DISTANT

• ZOOM - channel: 29

BIT % EFFECT

255 100

NARROW BEAM

0 0.0

WIDE BEAM

BIT % EFFECT

232-255 91,0-100 STAND BY BLACK

220-231 86,2-90,5 RANDOM MACRO 8

208-219 81,7-86,0 RANDOM MACRO 7

196-207 76,7-81,2 RANDOM MACRO 6

184-195 72,0-76,2 RANDOM MACRO 5

172-183 67,5-71,7 RANDOM MACRO 4

160-171 63,0-67,0 RANDOM MACRO 3

148-159 58,0-62,5 RANDOM MACRO 2

136-147 53,2-57,5 RANDOM MACRO 1

112-135 44,0-53,0 STAND BY BLACK

100-111 39,0-43,7 MACRO 8

88-99 34,2-38,7 MACRO 7

76-87 29,7-34,0 MACRO 6

64-75 25,0-29,5 MACRO 5

52-63 20,5-24,7 MACRO 4

40-51 15,5-20,0 MACRO 3

28-39 11,0-15,0 MACRO 2

16-27 6,2-10,5 MACRO 1

12-15 4,7-6,0 STAND BY BLACK

8-11 3,2-4,2 STAND BY

0-7 0,0-3,0 MACRO OFF

Continue

➔

Page 30

ALPHA PROFILE 1500

• PAN FINE - channel 34

Operation with option InvertPan

Off

(Tilt conventionally represented at 14% and option Invert Tilt

Off)

BIT %

255 100

00.0

Operation with option InvertPanGOn (Tilt conventionally represented at 14% and option Invert Tilt

Off)

BIT %

255 100

0 0.0

• TILT - channel 35

Operation with option Invert Tilt

Off

(Pan conventionally represented at 0% and option Invert Pan

Off)

BIT %

255 100

128 50.0

0 0.0

T X

S E L

D M X

T X

S E L

D M X

T X

S E L

D M X

Operation with option Invert TiltGOn (Pan conventionally represented at 0% and option Invert Pan

Off)

BIT %

255 100

128 50.0

0 0.0

T X

S E L

D M X

T X

S E L

D M X

T X

S E L

D M X

• TILT FINE - channel 36

Operation with option Invert Tilt

Off

(Pan conventionally represented at 0% and option Invert Pan

Off)

BIT %

255 100

00.0

T X

S E L

D M X

T X

S E L

D M X

Operation with option Invert TiltGOn (Pan conventionally represented at 0% and option Invert Pan

Off)

BIT %

255 100

0 0.0

T X

S E L

D M X

T X

S E L

D M X

• FUNCTION - channel: 37

BIT % EFFECT

55 100

51-62 20.0-24.2

38-50 14.7-19.5

25-37

9.7-14.2

12-24 4.7-9.5

0-11 0.0-4.2

LINEAR (Default)

UNUSED RANGE

63 24.7

CONVENTIONAL

DIMMER CURVE FUNCTION

FAST (Default)

NORMAL

PAN-TILT FUNCTION

The functions are actived passing through unused range and staying 5 seconds in necessary level.

• RESET - channel: 38

BIT % EFFECT

255 100

128 50.0 127 49.7

30.0

76 29.7

26 10.0

25 9.7

0 0.0

Complete reset is activated passing throug the unused range and staying 5 seconds in complete reset levels.

COMPLETE RESET PAN / TILT RESET

PAN / TILT RESET EFFECTS RESET

EFFECTS RESET

UNUSED RANGE

Pan / Tilt reset is activated passing throug the unused range and staying 5 seconds in Pan / Tilt reset levels.

Effects reset is activated passing throug the unused range and staying 5 seconds in Effects reset levels.

COMPLETE RESET

Page 31

ALPHA PROFILE 1500

•

LAMP CONTROL (only with option LAMP DMX On) - channel: 39

IMPORTANT: Alpha Profile 1500 is not provided with hot restrike igniter

LAMP ON (1500W)

BIT % EFFECT

255 100

180 70.5

00.0

101 39.5 100 39.0

LAMP OFF

179 70.0

26 10.0

LAMP OFF

25 9.7

UNUSED RANGE

Lamp ignition after 5 s in full power levels.

Lamp switch off passing throug the unused range and staying 5 s in Lamp OFF levels.

LAMP ON (1200W)

Immediate transition from full to half power.

Immediate transition from half to full power.

Lamp ignition not allowed in half power.

ON ON

OFF

Page 32

Timing Channel Channel function

40 Pan - Tilt time Pan – Tilt – Pan Fine – Tilt Fine

41 Colour time Cyan - Magenta - Yellow – C.T.O. – Color wheel

42 Beam time Dimmer – Zoom – Focus – Frost/Prism – Iris - Framing Rotation

43 Gobo time Fix Gobo –Rotating Gobo change

BIT Seconds

0 Full

10.2

20.4

30.6

40.8 51

61.2

71.4

81.6

91.8 10 2 11 2.2 12 2.4 13 2.6 14 2.8 15 3 16 3.2 17 3.4 18 3.6 19 3.8 20 4 21 4.2 22 4.4 23 4.6 24 4.8 25 5 26 5.2 27 5.4 28 5.6 29 5.8 30 6 31 6.2 32 6.4 33 6.6 34 6.8 35 7 36 7.2 37 7.4 38 7.6 39 7.8 40 8 41 8.2 42 8.4

BIT Seconds

43 8.6 44 8.8 45 9 46 9.2 47 9.4 48 9.6 49 9.8 50 10 51 10.2 52 10.4 53 10.6 54

55 56

57 58

59 60 61 14 62 63

64 65 66 16 67 68

69 70 71 18 72 73

74 75 76 20 77 78 79 21 80 81

82 83 84 23 85

BIT Seconds

87 88 89 25 90 91

92 93 94 27 95 96

97 98

99 29 100 101 102 30 103 104

105 106 107 32 108 109

110 111 112 34 113 114

115 116 117 36 118 119

120 121 122 38 123 124 125 39 126 127

128

BIT Seconds

129 130 41 131 132

133 134 135 43 136 137

138 139 140 45 141 142

143 144 145 47 146 147

148 149 150 49 151 152 153 50 154 155

156 157 158 52 159 160

161 162 163 54 164 165

166 167 168 56 169 170

171

BIT Seconds

172 173 58 174 175 176 59 177 178

179 180 181 65 182 183

184 185 186 75 187 188

189 190 191 85 192 193

194 195 196 95 197 198

100

199 200 201 110 202 203 204 120 205 206

130

207 208 209 140 210 211

150

212 213 214 160 215

BIT Seconds

216

170

217 218 219 180 220 221

190

222 223 224 200 225 226 227 210 228 229

220

230 231 232 230 233 234

240

235 236 237 250 238 239

260

240 241 242 270 243 244

280

245 246 247 290 248 249

300

250 251 252

310

253 254

255

Follow cue

Data

TIMING CHANNELS

TIME TABLE

CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035 -654311- Fax +39-035-301876 - www.claypaky.it

Rev. 1 02/12

Cod. 099106 - EN

gfstudio.com