Clay Paky A.LEDA B-EYE K10, A.LEDA B-EYE K20, A.LEDA B-EYE K10 C61415, A.LEDA B-EYE K20 C61420 Instruction Manual

1

A.LEDA B-EYE K10 A.LEDA B-EYE K20

C61415

C61420

®

INSTRUCTION MANUAL

Congratulations on choosing a Clay Paky product! We thank you for your custom. Please note that this product, as all the others in the rich Clay Paky range, has been designed and made with total quality to ensure excellent performance and best meet your expectations and requirements.

Carefully read this instruction manual in its entirety and keep it safe for future reference. It is essential to know the information and comply with the instructions given in this manual to ensure the fitting is installed, used and serviced correctly and safely. CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to other property or persons deriving from installation, use and maintenance that have not been carried out in conformity with this instruction manual, which must always accompany the fitting. CLAY PAKY S.p.A. reserves the right to modify the characteristics stated in this instruction manual at any time and without prior notice.

ENGLISH

PRELIMINARY

INDEX

Page

2

3

4

5

7

15

17

18

Contents

Safety information

Unpacking and preparation

Installation and start-up

Control panel

Menu setting

Maintenance

Technical information

Cause and solution of problems

Channel functions

PRELIMINARY

subject to change without prior notice

2

A.LEDA B-EYE

• Installation

Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used, it needs to be replaced with a genuine spare.

• Minimum distance of illuminated objects

The projector needs to be positioned so that the objects hit by the beam of light are at least 0.20 metres (8”) from the lens of the projector.

• Minimum distance from flammable materials

The projector must be positioned so that any flammable materials are at least 0.20 metres (8”) from every point on the surface of the fitting.

• Mounting surfaces

It is permissible to mount the fitting on normally flammable surfaces.

• Maximum ambient temperature

Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

• IP20 protection rating

The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0).

• Protection against electrical shock

Connection must be made to a power supply system fitted with efficient earthing (Class I appliance according to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the projectors from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• Connection to mains supply

Connection to the electricity mains must be carried out by a qualified electrical installer. Check that the mains frequency and voltage correspond to those for which the projector is designed as given on the electrical data label. This label also gives the input power to which you need to refer to evaluate the maximum number of fittings to connect to the electricity line, in order to avoid overloading.

• Temperature of the external surface

The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is 90°C (194°F).

• Maintenance

Before starting any maintenance work or cleaning the projector, cut off power from the mains supply.

• Battery

This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.

SAFETY INFORMATION

The products to which this manual refers comply with the European Directives pursuant to:

• 2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)

• 2004/108/EC - Electromagnetic Compatibility (EMC)

• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)

0.2

LED

IP20

tc90°C

LiFePO4

Pb

PRELIMINARY

subject to change without prior notice

3

A.LEDA B-EYE

UNPACKING AND PREPARATION

IST009/001

2 x 183102/805

1

90°

LOCKED

UNLOCKED

PAN Mechanism Lock and Release (every 90°) - Fig. 2

2

Packing contents - Fig. 1

PRELIMINARY

subject to change without prior notice

4

A.LEDA B-EYE

3

1

2

3

2

1

4

INSTALLATION AND START-UP

Connecting and disconnecting power cable - Fig. 4

Installing the projector - Fig. 3

The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.

WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.

PRELIMINARY

subject to change without prior notice

5

A.LEDA B-EYE

Switching on the projector - Fig. 7 Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:

Model Firmware xxx (Fixture ID) System errors

A.leda B-EYE Version X.X.X Dmx Address xxx E: .........................

Date - Hour W: .........................

On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 50% - Tilt 50%). The control panel (Fig. 7) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions: rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set). During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status. It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the

F

key will be cancelled.

CONTROL PANEL

7.5m

1

2

Dmx Address

Warning Message

Fixture ID

7

Continue

➔

Connecting to the control signal line (DMX) - Fig. 6 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3. IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.

Mains

5

6

SIGNAL

SCREEN

DMX 512

5 PIN

1

2

3

4

5

SIGNAL

SCREEN

1

3

2

DMX 512

3 PIN

SIGNAL

Connecting to the mains supply - Fig. 5

PRELIMINARY

subject to change without prior notice

6

A.LEDA B-EYE

28

Reversal of the display - Fig. 8 To activate this function, press UP

B

and DOWNCkeys simultaneously while the display is in the rest mode. This status will be memorised and

maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.

Setting the projector starting address

On each projector, the starting address must be set for the control signal (addresses from 1 to 512). The address can also be set with the projector switched off. Setting the address: see pag. 8.

Setting the projector Fixture ID

On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255). The Fixture ID address can be set with the projector switched off. Setting the Fixture ID: see pag. 8.

8

Functions of the buttons - Using the menu

Setting addresses and options with the projector disconnected

The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply. All that is needed is to press

F

to momentarily activate the display and thus access the settings. Once the required operations have been carried out,

the display will switch off again after a wait time of 30 seconds.

USING THE MENU:

1) Press

F

once – “Main Menu” appears on the display.

2) Use the UP

B

and DOWN Ckeys to select the menu to be used:

• Setup (Setup Menu): To set the setting options.

• Option (Option Menu): To set the operating options

• Informations (Informations Menu): To read the counters, software version and other information.

• Manual Control (Manual control Menu): To trigger the test and manual control functions.

• Test (Test Menu): To check the proper functionning of effects

• Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel. To enable the "Advanced" see pag.13

3) Press

F

to display the first item in the selected menu.

4) Use the UP

B

and DOWN Ckeys to select the MENU items.

Confirms the displayed value, or activates the displayed function, or enters the successive menu.

Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.

Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.

Return to the top level.

Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù.

F

C

DOWN

B

UP

D

LEFT

E

RIGHT

PRELIMINARY

subject to change without prior notice

7

A.LEDA B-EYE

MENU SETTING

Continue

➔

System

Errors

Information

Fixture

Hours

LED

Energy Tot

4

Reset

Manual Control

Channel

6

3

System Version

Board

Diagnost.

Dmx

Monitor

Fans

Monitor

Access code

1234

Advanced

Calibration

Upload

Aleda fw

Setup Model

Set Up

Option

Information

Manual Control

Test

Advanced

1

5

Pan / Tilt

Colour

All

Test

Dmx

Address

Channel

Mode

Ethernet Interface

Fixture ID

Network

params

2

Pan / Tilt

Silent Mode

Display

Option

Invert

Pan

Invert

Tilt

Swap

Pan-Tilt

Encoder

Pan-Tilt

Standard

Special

Functions

Setting

Default

Preset

User

Preset 1

User

Preset 2

User

Preset 3

Pan/Tilt

speed

Dimmer

curve

RGB

Gamma

Halogen

Mode

Quiet

PRELIMINARY

subject to change without prior notice

8

A.LEDA B-EYE

DMX ADDRESS NOTE: without the DMX signal the Address (XXX) flashing

Allows you to select the DMX ADDRESS.

1) Press

F

- the current DMX Adress appear on the display.

2) Use the UP

B

and DOWN C, RIGHT Ekeys to plan the DMX

Address.

3) Press

F

to confirm the selection or LEFT Dto keep current settings.

CHANNEL MODE

Allows you to select a channel arrangement from the four available.

1) Press

F

- the current settings appear on the display.

2) Use the UP

B

and DOWN Ckeys to select one of the following

settings:

- Standard

- Shape

- Extended

- Extended RGBW

3) Press

F

to confirm the selection or LEFT Dto keep current settings.

FIXTURE ID

Allows you to select the FIXTURE ID.

1) Press

F

- the current Fixture ID appear on the display.

2) Use the UP

B

, DOWN C, RIGHT Ekeys to plan the Fixture ID.

3) Press

F

to confirm the selection or LEFT Dto keep current settings.

ETHERNET INTERFACE

It lets you set the Ethernet settings to be attributed to the projector.

1) Premere

F

.

2) Use the UP

B

and DOWN Ckeys to select the “Ethernet Interface”

options to set:

Control Protocol

It lets you select the “Control Protocol” Art-net to assign according to the control unit used:

1) Press

F

the current setting appears on the display.

2) Use the UP

B

and DOWN Ckeys to select one of the following settings:

- Disabled

- Art-net on IP 2

- Art-net on IP 10

3) Press

F

to confirm the selection or LEFT Dto keep the current setting.

Repeat on DMX

It lets you enable the transmission of the Ethernet protocol by DMX signal to all the connected projectors.

1) Press

F

the current setting appears on the display.

2) Use the UP

B

and DOWN Ckeys to select one of the following settings:

- Disabled: DMX transmission disabled.

- Enabled on primary: DMX transmission enabled.

3) Press

F

to confirm the selection or LEFT Dto keep the current setting.

Universe

It lets you assign the “Universe” number to be assigned to a series of projectors.

1) Press

F

– the current Universe address appears on the display.

2) Use the UP

B

, DOWN C, RIGHT Ekeys to set the Universe

address.

3) Press

F

to confirm the selection or LEFT Dto keep the current

setting.

SET UP MENU

NOTE: On grey the default options

Set Up

Dmx

Address

Channel

Mode

Fixture ID

Address xxx

Standard

Shape

Extended

RGBW

Value xxx

Ethernet Interface

Control

Protocol

Repeat on

DMX

Universe

PRELIMINARY

subject to change without prior notice

9

A.LEDA B-EYE

Continue

➔

PAN / TILT Invert pan

Used for reversing Pan movement.

1) Press

F

- the current settings appear on the display (On or Off).

2) Use the UP

B

and DOWN Ckeys to enable (On) or disable (Off)

PAN inversion.

3) Press

F

to confirm the selection or LEFT Dto keep current

settings.

Invert tilt

Used for reversing tilt movement.

1) Press

F

- the current settings appear on the display (On or Off).

2) Use the UP

B

and DOWN Ckeys to enable (On) or disable (Off)

Tilt inversion.

3) Press

F

to confirm the selection or LEFT Dto keep current

settings.

Swap Pan-Tilt

Used for swapping Pan and Tilt channels (as well as Pan fine and Tilt fine).

1) Press

F

- the current settings appear on the display (On or Off).

2) Use the UP

B

and DOWN Ckeys to enable (On) or disable (Off)

Pan and Tilt channel swap.

3) Press

F

to confirm the selection or LEFT Dto keep current

settings.

Encoder Pan-Tilt

Used for enabling the Pan / Tilt encoders.

1) Press

F

- the current settings appear on the display (On or Off).

2) Use the UP

B

and DOWN Ckeys to enable (On) or disable (Off)

Pan / Tilt encoders.

3) Press

F

to confirm the selection or LEFT Dto keep current

settings.

SILENT MODE

It lets you select the “Silent Mode” from the two available.

1) Press

F

the current setting appears on the display.

2)

Use the UP Band DOWN Ckeys to select one of the following settings: Standard: Maximum speed and consequently maximum effects noise level. Quiet: reduces the speed of some effects, thereby reducing their noise level.

3) Press Fto confirm the selection or LEFT Dto keep the current setting.

DISPLAY

Used for automatically reduce brightness on the display after about 30 seconds in idle.

1) Press

F

- the current settings appear on the display (On or Off).

2) Use the UP

B

and DOWN Ckeys to enable (On) or disable

(Off) the decreasing of display brightness.

3) Press

F

to confirm the selection or LEFT Dto keep current

settings.

SPECIAL FUNCTIONS Pan / Tilt speed

Lets you select two different Pan and Tilt speeds.

1) Press

F

- the current setting appears on the display.

2) Use the UP

B

and DOWN Ckeys to select one of the following

settings:

- Normal

- Fast

3) Press

F

to confirm the selection or LEFT Dto keep current

settings.

OPTIONS MENU

Swap

Pan-Tilt

On

Off

Encoder Pan-Tilt

On

Off

Pan / Tilt

Option

Invert

Pan

On

Off

Invert

Tilt

On

Off

Silent mode

Standard

Quiet

Special

Functions

Pan / Tilt

speed

On

Off

Display

PRELIMINARY

subject to change without prior notice

10

A.LEDA B-EYE

Dimmer Curve

Lets you select four different Dimmer channel curves.

1) Press

F

- the current setting appears on the display.

2) Use the UP

B

and DOWN Ckeys to select one of the following

settings:

- Curve 1

- Curve 2

- Curve 3

- Curve 4

3) Press

F

to confirm the selection or LEFT Dto keep current settings.

RGB Gamma

Lets you select three different RGBW gamma curves.

1) Press

F

- the current setting appears on the display.

2) Use the UP

B

and DOWN Ckeys to select one of the following

settings:

- Gamma 1.0

- Gamma 1.5

- Gamma 2.0

3) Press

F

to confirm the selection or LEFT Dto keep current settings.

Halogen Mode

Lets you select five different halogen lamp simulations.

1) Press

F

- the current setting appears on the display.

2) Use the UP

B

and DOWN Ckeys to select one of the following

settings:

- Halogen OFF

- Halogen Lamp 1

- Halogen Lamp 2

- Halogen Lamp 3

- Halogen Lamp 4

- Halogen Lamp 5

3) Press

F

to confirm the selection or LEFT Dto keep current settings.

SETTING

Used to save 3 different settings of the items in the options menu and relative submenus.

1) Press

F

- “Default preset” appears on the display.

2) Use the UP

B

and DOWN Ckeys to select one of the following

configurations:

- Default preset (*)

- User preset 1

- User preset 2

- User Preset 3

3) Press

F

- “Load preset X” appears on the display.

4) Use the UP

B

and DOWN Ckeys to select:

- Load preset X to recall a previously stored configuration.

- Save to preset X to store the current configuration. a confirmation message (Are you sure?) appears on the display.

5) Select YES to confirm the selection or NO to keep the current setting and return to the next higher level.

(*) DEFAULT PRESET

By pressing the RIGHT

E

key and the LEFT Dkey simultaneously once entered in the "main menu" it is possible to quickly (short cut) reset the default settings (DEFAULT PRESET).

Used for restoring default values on all options menu items and relevant submenus.

1) Press

F

, a confirmation message (Are you sure?) appears on the display.

2) Select YES to confirm the selction or NO to keep current setting. OPTION DEFAULT Invert Pan Off Invert Tilt Off Swap Pan-Tilt Off Encoder Pan-Tilt On Display On Silent Mode Standard P/T Speed Fast Dimmer Curve Curve 1 RGB Gamma Gamma 1.5 Halogen Mode Halogen Off

Dimmer

Curve

Option

Special

Functions

RGB

Gamma

Halogen

Mode

Save To Preset 3

Reset To

Dafault

Go Back

Setting

Default Preset

Load

Preset 1

Save To Preset 1

User

Preset 1

Load

Preset 2

Save To Preset 2

User

Preset 2

Load

Preset 3

User

Preset 3

PRELIMINARY

subject to change without prior notice

11

A.LEDA B-EYE

Continue

➔

SYSTEM ERRORS

Shows a list of warnings and messages relevant to errors occurred since the fixtures switching-on.

1) Pressing

F

you are allowed to reset the SYSTEM ERRORS list. A confirmation message (Are you sure you want to clear error list ?) appears on the display.

2) Select YES to reset the list or NO to go back.

FIXTURE HOURS

Used for displaying projector operating hours (total and partial).

1) Press

F

- Hours total and partial appears on the display.

Total counter

Counts the number of projector working life hours (from manufacture to date).

Partial counter

Counts the number of partial projector working life hours since the last reset to date.

2) Press

F

to reset partial projector working hours a confirmation

message (Are you sure?) appears on the display.

3) Select YES to reset partial projectors counter or NO to keep the current setting and return to the top menu level.

LED ENERGY TOT

Lets you view total LED working hours.

1) Press

F

- to display total and partial Watts/hour:

Total

Total LED working hours from construction to date.

Partial

LED working hours from last reset to date.

2) Press

F

to reset the partial counter. A confirmation appears on the

screen (Are you sure?)

3) Select YES to reset the partial counter or NO to keep the current setting and open the next menu level.

SYSTEM VERSION

Used for displaying the software and hardware version of each board installed in the projector. CPU brd (CPU board) 0: PT-3f (Scheda Pan / Tilt) 1: Ld - Kxx (Scheda LED)

BOARD DIAGNOSTIC

Used for displaying the status error of each board installed in the projector: 0: PT-3f (Scheda Pan / Tilt) 1: Ld - Kxx (Scheda LED)

DMX MONITOR

Used for displaying the projector DMX channel level in bit (Val) and in percentage (Perc).

FANS MONITOR

Used for displaying the speed of each fan installed in the projector: PwrSp (fan PSU) Head (fan head)

NETWORK PARAMS

Allows the "Network" parameters of the projector to be displayed or:

IP address: Internet Protocol address (two projectors must not have the same IP address)

IP mask: 255.0.0.0 Mac address: Media Access Control: the projector’s Ethernet Address.

INFORMATION MENU

Information

System

Errors

Fixture

Hours

Total XXX Partial XXX

Reset...

LED Energy

Tot

System Version

Board Revis. Hw.rv. CPU brd x.x.x x.x com.dev x.x 0: PT-3f x.x x.x 1: Ld - Kxx x.x x.x

Network

params

Dmx

Monitor

Board Status Err% 0:PT-3f Good 0.00 1: Ld - Kxx Good 0.00

Fans

Monitor

Fan Speed (RPM) PwrSp XXXX Head XXXX

Board

Diagnost.

PRELIMINARY

subject to change without prior notice

12

A.LEDA B-EYE

RESET

Used for resetting the projector.

1) Press

F

to reset the projectors, a confirmation message (Are you

sure ?) appears on the display.

2) Select YES to starting reset the fixture or NO to keep the current setting and return to the top menu level.

CHANNEL

Used for setting channel levels from the projector control panel.

1) Press

F

- the first channel appears on the display.

2) Use the UP

B

and DOWN Ckeys to select the required channel:

3) Press

F

and use the UP Band DOWN Ckeys to select the

required DMX level (value between 0 and 255).

4) Press LEFT

D

to return to the top menu level.

TEST

Allows you to check the proper functioning of effects.

1) Press

F

to return to the top menu level.

2) Use the UP

B

and DOWN Ckeys to select the required test.

3) Press

F

to confirm the selection or LEFT Dto keep current settings. Test sequence: Pan - Tilt effects (Pan & Tilt) Colour effects (CMY / CTO / Colour wheel) All effects

To enable the "Advanced Menu" set up the "Access code" (1234) using the UP

B

, DOWN C, RIGHT Ekeys.

Press

F

- "Menu advanced" appears on the display

UP LOAD FIRMWARE

Allows you to transfer the firmware from 1 fixture to all the connected fixtures.

1) Press

F

, a confirmation message appears on the display.

2) Select YES to start the firmware loading or NO to keep the current set-

ting and return to the top menu level

SETUP MODEL

Allows you to change the default model of projector.

1) Press

F

a confirmation message appears on the display.

2) Select YES to define the model of projector or NO to keep the current

setting and return to the top menu level.

CALIBRATION

Allows you to adjust effects from the control panel to obtain perfect uniformity between the projectors.

1) Press

F

- “channels” appears on the display.

2) Using the UP

B

and DOWN Ckeys, select the effect you wish to

regulate.

3) Press

F

and use the RIGHT E, UP Band DOWN Cbuttons to

make the adjustment by setting a value between 0 and 255.

4) Press

F

to confirm the selection

or

LEFT Dto keep current set-

tings and return to the top level.

FACTORY DEFAULT

Allows you to restore default values of all channels (128).

1) Press

F

– a confirmation message appears on the display (Reset

calibration to factory default ?).

2) Select YES to reset calibration to factory default or NO to keep the

current setting and return to the top menu level.

Manual Control

No

Yes

Reset

Channel

Test

Pan-Tilt Colour All

Advanced

Code

1234

Calibration

Upload

Aleda fw

Transfer the firmware on all the connected fixtures ? Are you sure ? Yes/No

Setup Model

Changing to a wrong model may damage the fixture. Are you sure ? Yes/No

MANUAL CONTROL

TEST MENU

ADVANCED MENU

PRELIMINARY

subject to change without prior notice

13

A.LEDA B-EYE

9

WARNING: no alcohol

CAUTION:

• To avoid damage to the internal parts of the fixture when the fixture is not working, is recommended to turn the head down before turning the fixture off, so that the front lenses of the fixture are invested as little as possible from the sun.

• Set channel 20 (Zoom) to 100% (255-bit) before turning off the projector to facilitate the packaging of the projector.

• To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The

frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.). It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:

• General cleaning of internal parts.

• Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Clay Paky.

• General visual check of the internal components, cabling, mechanical parts, etc.

• Electrical, photometric and functional checks; eventual repairs.

Cleaning the lenses

Only use neutral soap and water to clean the lenses, then dry it carefully with a soft, non-abrasive cloth. (WARNING: the use of alcohol or any other detergent could damage the lenses).

PRELIMINARY

subject to change without prior notice

14

A.LEDA B-EYE

5

6

3

4

1

2

10

Battery removal - Fig. 10

This product contains a rechargeable lead-acid battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.

LiFePO4

PRELIMINARY

subject to change without prior notice

15

A.LEDA B-EYE

1

2

3

4

2

1

11

12

Opening the covers - Fig. 11

Removing/Assembling the lens unit - Fig. 12

MAINTENANCE

PRELIMINARY

subject to change without prior notice

16

A.LEDA B-EYE

13

Replacing the line actuator - Fig. 13

PRELIMINARY

subject to change without prior notice

17

A.LEDA B-EYE

479

(18.86")

358

(14.09")

253

(9.96")

423

(16.65")

248

(9.76")

360

(14.17")

290

(11.42")

Zoom IN

340

(13.39")

Zoom OUT

180

(7.09")

Zoom IN

230

(9.06")

Zoom OUT

589

(23.19")

330

(12.99")

395

(15.55")

476

(18.74")

370

(14.57")

460

(18.11")

380 (14.96") Zoom IN

430 (16.93")

Zoom OUT

200

(7.87")

Zoom IN

250

(9.84")

Zoom OUT

TECHNICAL INFORMATION

Power supplies available

100-240V 50/60Hz

Input power

•

K20 - 750VA

•

K10 - 450VA

LED source

LED Osram Ostar RGBW - 15W Average LED life: 50.000 h

Motors

5 (k10), 7 (k20) stepper motors, operating with microsteps, totally microprocessor controlled.

Cooling

• High efficiency die-cast aluminium

• Forced ventilation

Inputs

DMX 512

Working position

Functioning in any position.

Movable body

•

Movement by means of two stepper motors, controlled by microprocessor.

•

Automatic repositioning of PAN and TILT after accidental movement not controlled by control unit.

• Travel:

- PAN = 540°

- TILT = 210°

IP20 protection rating

• Protected against the entry of solid bodies larger than 12mm (0.47”).

• No protection against the entry of liquids.

CE Marking

Complies with the following European Directives

- 2006/95/EC (LVD)

- 2004/108/EC (EMC)

- 2011/65/EU (RoHS).

Weights

• K10: 14.5 kg

• K20: 21 kg

CAUSE AND SOLUTION OF PROBLEMS

THE PROJECTOR WILL NOT SWITCH ON

PROBLEMS

ELECTRONICS NON-OPERATIONAL

DEFECTIVE PROJECTION

REDUCED LUMINOSITY

POSSIBLE CAUSES CHECKS AND REMEDIES

No mains supply. LED exhausted or defective. Signal transmission cable faulty or disconnected. Incorrect addressing. Fault in the electronic circuits. Lenses or reflector broken Dust or grease deposited.

Check the power supply voltage. Call an authorised technician. Replace the cables. Check addresses (see instructions). Call an authorised technician. Call an authorised technician. Clean (see instructions).

PRELIMINARY

subject to change without prior notice

18

A.LEDA B-EYE

CHANNEL FUNCTION

A.LEDA B-EYE K10

CHAN-

NEL

STANDARD EXTENDED

CHANNEL MODE

Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20

CHAN-

NEL

SHAPES

CHANNEL MODE

Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Shape Selection Shape Speed Shape Smoothing Shape Red Shape Green Shape Blue Shape White Shape Intensity Background Intensity Shape Transition Shape Offset

1

2

3

4

5

6

7

8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

CHAN-

NEL

CHANNEL MODE

Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Red LED 1 Green LED 1 Blue LED 1 Red LED 2 Green LED 2 Blue LED 2 Red LED 3 Green LED 3 Blue LED 3 Red LED 4 Green LED 4 Blue LED 4 Red LED 5 Green LED 5 Blue LED 5 Red LED 6 Green LED 6 Blue LED 6 Red LED 7 Green LED 7 Blue LED 7 Red LED 8 Green LED 8 Blue LED 8 Red LED 9 Green LED 9 Blue LED 9

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47

CHAN-

NEL

CHANNEL MODE

Red LED 10 Green LED 10 Blue LED 10 Red LED 11 Green LED 11 Blue LED 11 Red LED 12 Green LED 12 Blue LED 12 Red LED 13 Green LED 13 Blue LED 13 Red LED 14 Green LED 14 Blue LED 14 Red LED 15 Green LED 15 Blue LED 15 Red LED 16 Green LED 16 Blue LED 16 Red LED 17 Green LED 17 Blue LED 17 Red LED 18 Green LED 18 Blue LED 18 Red LED 19 Green LED 19 Blue LED 19

48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77

PRELIMINARY

subject to change without prior notice

19

A.LEDA B-EYE

Continue

➔

EXTENDED RGBW

CHAN-

NEL

CHANNEL MODE

Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Red LED 1 Green LED 1 Blue LED 1 White LED 1 Red LED 2 Green LED 2 Blue LED 2 White LED 2 Red LED 3 Green LED 3 Blue LED 3 White LED 3 Red LED 4 Green LED 4 Blue LED 4 White LED 4 Red LED 5 Green LED 5 Blue LED 5 White LED 5 Red LED 6 Green LED 6 Blue LED 6 White LED 6 Red LED 7 Green LED 7 Blue LED 7 White LED 7 Red LED 8

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

CHAN-

NEL

CHANNEL MODE

Green LED 8 Blue LED 8 White LED 8 Red LED 9 Green LED 9 Blue LED 9 White LED 9 Red LED 10 Green LED 10 Blue LED 10 White LED 10 Red LED 11 Green LED 11 Blue LED 11 White LED 11 Red LED 12 Green LED 12 Blue LED 12 White LED 12 Red LED 13 Green LED 13 Blue LED 13 White LED 13 Red LED 14 Green LED 14 Blue LED 14 White LED 14 Red LED 15 Green LED 15 Blue LED 15 White LED 15 Red LED 16 Green LED 16 Blue LED 16 White LED 16 Red LED 17 Green LED 17 Blue LED 17 White LED 17 Red LED 18 Green LED 18 Blue LED 18 White LED 18 Red LED 19 Green LED 19 Blue LED 19 White LED 19

50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

PRELIMINARY

subject to change without prior notice

20

A.LEDA B-EYE

A.LEDA B-EYE K20

STANDARD EXTENDED

CHAN-

NEL

CHANNEL MODE

Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Lenses rotatation Red LED 1 Green LED 1 Blue LED 1 Red LED 2 Green LED 2 Blue LED 2 Red LED 3 Green LED 3 Blue LED 3 Red LED 4 Green LED 4 Blue LED 4 Red LED 5 Green LED 5 Blue LED 5 Red LED 6 Green LED 6 Blue LED 6 Red LED 7 Green LED 7 Blue LED 7 Red LED 8 Green LED 8 Blue LED 8 Red LED 9 Green LED 9 Blue LED 9 Red LED 10 Green LED 10 Blue LED 10 Red LED 11 Green LED 11 Blue LED 11 Red LED 12 Green LED 12 Blue LED 12 Red LED 13 Green LED 13 Blue LED 13 Red LED 14 Green LED 14 Blue LED 14 Red LED 15 Green LED 15 Blue LED 15

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

CHAN-

NEL

CHANNEL MODE

Red LED 16 Green LED 16 Blue LED 16 Red LED 17 Green LED 17 Blue LED 17 Red LED 18 Green LED 18 Blue LED 18 Red LED 19 Green LED 19 Blue LED 19 Red LED 20 Green LED 20 Blue LED 20 Red LED 21 Green LED 21 Blue LED 21 Red LED 22 Green LED 22 Blue LED 22 Red LED 23 Green LED 23 Blue LED 23 Red LED 24 Green LED 24 Blue LED 24 Red LED 25 Green LED 25 Blue LED 25 Red LED 26 Green LED 26 Blue LED 26 Red LED 27 Green LED 27 Blue LED 27 Red LED 28 Green LED 28 Blue LED 28 Red LED 29 Green LED 29 Blue LED 29 Red LED 30 Green LED 30 Blue LED 30 Red LED 31 Green LED 31 Blue LED 31 Red LED 32 Green LED 32 Blue LED 32 Red LED 33 Green LED 33 Blue LED 33 Red LED 34 Green LED 34 Blue LED 34 Red LED 35 Green LED 35 Blue LED 35 Red LED 36 Green LED 36 Blue LED 36 Red LED 37 Green LED 37 Blue LED 37

67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98

99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132

CHAN-

NEL

CHANNEL MODE

Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Lenses rotatation

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21

CHAN-

NEL

SHAPES

CHANNEL MODE

Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Lenses rotatation Shape Selection Shape Speed Shape Smoothing Shape Red Shape Green Shape Blue Shape White Shape Intensity Background Intensity Shape Transition Shape Offset

1

2

3

4

5

6

7

8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

PRELIMINARY

subject to change without prior notice

21

A.LEDA B-EYE

EXTENDED RGBW

CHAN-

NEL

CHANNEL MODE

Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Lenses rotatation Red LED 1 Green LED 1 Blue LED 1 White LED 1 Red LED 2 Green LED 2 Blue LED 2 White LED 2 Red LED 3 Green LED 3 Blue LED 3 White LED 3 Red LED 4 Green LED 4 Blue LED 4 White LED 4 Red LED 5 Green LED 5 Blue LED 5 White LED 5 Red LED 6 Green LED 6 Blue LED 6 White LED 6 Red LED 7 Green LED 7 Blue LED 7 White LED 7 Red LED 8 Green LED 8 Blue LED 8 White LED 8 Red LED 9 Green LED 9 Blue LED 9 White LED 9

1

2

3

4

5

6

7

8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57

CHAN-

NEL

CHANNEL MODE

Red LED 10 Green LED 10 Blue LED 10 White LED 10 Red LED 11 Green LED 11 Blue LED 11 White LED 11 Red LED 12 Green LED 12 Blue LED 12 White LED 12 Red LED 13 Green LED 13 Blue LED 13 White LED 13 Red LED 14 Green LED 14 Blue LED 14 White LED 14 Red LED 15 Green LED 15 Blue LED 15 White LED 15 Red LED 16 Green LED 16 Blue LED 16 White LED 16 Red LED 17 Green LED 17 Blue LED 17 White LED 17 Red LED 18 Green LED 18 Blue LED 18 White LED 18 Red LED 19 Green LED 19 Blue LED 19 White LED 19 Red LED 20 Green LED 20 Blue LED 20 White LED 20 Red LED 21 Green LED 21 Blue LED 21 White LED 21 Red LED 22 Green LED 22 Blue LED 22 White LED 22 Red LED 23 Green LED 23 Blue LED 23 White LED 23 Red LED 24

58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98

99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114

CHAN-

NEL

CHANNEL MODE

Green LED 24 Blue LED 24 White LED 24 Red LED 25 Green LED 25 Blue LED 25 White LED 25 Red LED 26 Green LED 26 Blue LED 26 White LED 26 Red LED 27 Green LED 27 Blue LED 27 White LED 27 Red LED 28 Green LED 28 Blue LED 28 White LED 28 Red LED 29 Green LED 29 Blue LED 29 White LED 29 Red LED 30 Green LED 30 Blue LED 30 White LED 30 Red LED 31 Green LED 31 Blue LED 31 White LED 31 Red LED 32 Green LED 32 Blue LED 32 White LED 32 Red LED 33 Green LED 33 Blue LED 33 White LED 33 Red LED 34 Green LED 34 Blue LED 34 White LED 34 Red LED 35 Green LED 35 Blue LED 35 White LED 35 Red LED 36 Green LED 36 Blue LED 36 White LED 36 Red LED 37 Green LED 37 Blue LED 37 White LED 37

115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169

PRELIMINARY

subject to change without prior notice

22

A.LEDA B-EYE

BIT

EFFECT

2550COLOUR INSERTED

COLOUR EXCLUDED

• RED – GREEN - BLUE - WHITE

BIT

EFFECT

255

0

• RED FINE – GREEN FINE – BLUE FINE – WHITE FINE

NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 50% - Tilt 50%) all the others channels stay at 0%.

• C.T.O.

BIT

EFFECT

255

250

246

242

237

233

228

224

219

215

210

206

201

197

192

188

184

179

175

170

166

161

157

152

148

144

139

135

130

126

121

117

112

108

103

99

95

90

86

81

77

72

68

63

59

54

50

46

41

37

32

28

23

19

14

10

0-9

2500

2600

2700

2800

2900

3000

3100

3200

3300

3400

3500

3600

3700

3800

3900

4000

4100

4200

4300

4400

4500

4600

4700

4800

4900

5000

5100

5200

5300

5400

5500

5600

5700

5800

5900

6000

6100

6200

6300

6400

6500

6600

6700

6800

6900

7000

7100

7200

7300

7400

7500

7600

7700

7800

7900

8000

UNUSED RANGE

Note: If CTO channel is active, the WHITE channel is disabled.

PRELIMINARY

subject to change without prior notice

23

A.LEDA B-EYE

• STOP / STROBE

MACRO

BIT EFFECT

252 - 255

OPEN

0 - 3

CLOSED

213 - 225

RANDOM SLOW STROBE

4

SLOW STROBE (1 f lash/sec)

103

FAST STROBE (25 flash/sec)

104 - 107

OPEN

108

SLOW PULSATION

(0,5 flash/sec)

208 - 212

OPEN

226 - 238

RANDOM MEDIUM ST ROBE

239 - 251

RANDOM FAST STROBE

207

FAST PULSATION

(25 flash/sec)

• MACRO COLOUR

• DIMMER

BIT EFFECT

255 FULL LIGHT

NO LIGHT0

• DIMMER FINE

BIT EFFECT

255

0

BIT COLOUR

LEE

REFERENCE

BIT VALUE

RG BW

209-255

208

207

191-206

184-190

180-183

179

175-178

174

172-173

168-171

162-167

157-161

151-156

149-150

147-148

146

145

142-144

138-141

136-137

134-135

131-133

129-130

128

127

126

125

123-124

121-122

120

119

118

117

115-116

114

113

112

110-111

100-109

89-99

78-88

68-77

62-67

49-61

46-48

45

35-44

32-34

31

30

29

27-28

23-26

20-22

19

18

17

16

15

14

13

12

11

10

0-9

-

197

181

174

170

169

165

164

162

158

152

147

141

139

137

136

135

132

128

126

124

121

119

118

117

116

115

113

111

110

109

108

107

105

104

103

102

100

90

79

68

58

52

39

36

35

25

22

21

20

19

17

13

10

-

255

128

77

181

255

82

255

222

253

255

0

77

219

255

0

255

227

84

206

0

74

206

51

255

217

255

230

237

245

41

0

243

255

198

152

156

0

255

216

255

0

255

-

235

255

0

255

168

199

214

46

181

84

171

143

255

197

58

255

53

41

255

186

255

20

109

130

138

148

141

122

166

160

163

202

219

194

255

117

107

87

112

83

65

100

135

56

114

115

126

0

137

201

237

0

255

0

255

0

-

66

122

143

255

95

64

49

90

2

28

0

26

13

87

0

79

61

0

143

36

56

13

0

255

82

56

51

15

33

28

31

23

31

0

130

135

133

39

0

2

0

9

0

25

61

255

0

255

0

-

255

0

69

0

199

197

130

107

141

0

193

255

0

-

White

Dirty White

Alice Blue

Congo Blue

Dark Steel Blue

Deep lavender

Lilac Tint

Daylight Blue

Flame Red

Bastard Amber

Deep Orange

Pale Gold

Apricot

Bright Blue

Primary Green

Special lavender

Pale Lavender

Deep Golden Amber

Medium Blue

Bright Pink

Mauve

Dark Green

Leaf Green

Dark Blue

Light Blue

Steel Blue

Med Blu Green

Peacock Blue

Magenta

Dark Pink

Middle Rose

Light Salmon

English Rose

Light Rose

Orange

Deep Amber

Straw

Light Amber

Spring Yellow

Dark yellow green

Just Blue

Sky Blue

Lavender

Light Lavender

Pink Carnation

Medium Pink

Light Pink

Sunrise Red

Dark Amber

Gold Amber

Medium Amber

Fire

Surprise Peach

Straw Tint

Medium Yellow

Black

White 5000°K

White 3700°K

White 7000°K

Magenta

Yellow

Cyan

Blue

Green

Red

Macro color OFF

Continue

➔

PRELIMINARY

subject to change without prior notice

24

A.LEDA B-EYE

BIT

255

0

BIT

255

0

Operation with option InvertPan

G

On

(Tilt conventionally represented at 14% and option Invert Tilt

G

Off)

• TILT

Operation with option InvertPan

G

Off

(Tilt conventionally represented at 14% and option Invert Tilt

G

Off)

• PAN FINE

Operation with option InvertPan

G

Off

(Tilt conventionally represented at 14% and option Invert Tilt

G

Off)

BIT

255

0

Operation with option InvertPanGOn (Tilt conventionally represented at 14% and option Invert Tilt

G

Off)

BIT

255

0

Operation with option InvertPan

G

On

(Tilt conventionally represented at 14% and option Invert Tilt

G

Off)

BIT

255

0

BIT

255

0

• PAN

Operation with option InvertPan

G

Off

(Tilt conventionally represented at 14% and option Invert Tilt

G

Off)

BIT

255

0

BIT

255

0

Operation with option InvertPanGOn (Tilt conventionally represented at 14% and option Invert Tilt

G

Off)

• TILT FINE

Operation with option InvertPan

G

Off

(Tilt conventionally represented at 14% and option Invert Tilt

G

Off)

PRELIMINARY

subject to change without prior notice

25

A.LEDA B-EYE

• FUNCTION

BIT EFFECT

251 – 255

103 – 250

98 – 102

93 – 97

88 – 92

83 – 87

78 – 82

73 – 77

68 – 72

63 – 67

58 – 62

53 – 57

48 – 52

43 – 47

38 – 42

25 – 37

12 – 24

0 – 11

Reset to defult

Unused Range

Halogen Lamp Simulation, type 5 (2500 W)

Halogen Lamp Simulation, type 4 (2000 W)

Halogen Lamp Simulation, type 3 (1200 W)

Halogen Lamp Simulation, type 2 (1000 W)

Halogen Lamp Simulation, type 1 (750W)

Halogen Lamp Simulation OFF (Default)

RGBW Gamma curve 3 – gamma = 2.0

RGBW Gamma curve 2 – gamma = 1.5 (Default)

RGBW Gamma curve 1 – gamma = 1.0

Dimmer Curve 4

Dimmer Curve 3 (Default)

Dimmer Curve 2

Dimmer Curve 1

Pan Tilt Normal

Pan Tilt Fast (Default)

Function off

The functions are actived passing through the “unused range” and staying 5 seconds in necessary level. Last selected function still active. Enable setting a new function.

DIMMER CURVE 1 - GAMMA 1 LINEAR

DIMMER CURVE 2 - GAMMA 1,5

DIMMER CURVE 3 - GAMMA 2,0

• RESET

BIT

EFFECT

255

128 127

77 76

26 25

0

ZOOM RESET

UNUSED RANGE

Pan / Tilt reset is activated passing throug the unused range and staying 5 seconds in Pan / Tilt reset levels

Effects reset is activated passing throug the unused range and staying 5 seconds in Effects reset levels.

COMPLETE RESET

COMPLETE RESET PAN / TILT RESET

PAN / TILT RESET ZOOM RESET

Complete reset is activated passing throug the unused range and staying 5 seconds in complete reset levels

• LENSES ROTATION

0

127

STOP

255

FAS T ROTATION

193

SLOW ROTATION

191 - 192

STOP

190

SLOW ROTATION

BIT EFFECT

128

F

LINEAR ROTATION

AST ROTATION

* Automatic gamma is calculated based on background intensity to auto-adapt the

shape’s fade.

DIMMER CURVE 4 - S

Continue

➔

PRELIMINARY

subject to change without prior notice

26

A.LEDA B-EYE

SHAPE SELECTION - SHAPE SPEED - SHAPE OFFSET

BIT SHAPE SELECTION

RANDOM

COLORS *1

SHAPE SPEED SHAPE OFFSET

On K5

On

K10

On

K20

32-255

31

30 29 28 27 26 25

24

23

22

21

20 19

18 17

16 15

14 13 12 11 10

9 8

0-7

No No

Yes Yes Yes Yes Yes Yes

Yes

Yes Yes

No No

Yes

No

No Yes Yes Yes

Yes Yes

Yes Yes Yes Yes Yes Yes

Yes

Yes Yes

No Yes Yes

No Yes Yes Yes Yes

Yes Yes

Yes Yes Yes Yes Yes Yes

Yes

Yes Yes

Yes Yes Yes Yes Yes Yes Yes Yes

N.a.

Yes

N.a. N.a.

Yes Yes

N.a. N.a.

Reserved Two rotating arcs of different colors and direction Two rotating arcs of different colors Two rotating bars of different colors Triangle Half moon Bar (2 arms) Fan (3 arms)

Rainbow 2, fixed speed with variable color offset.

Rainbow 1, variable speed.

Random pixels with variable density and speed Random pixels distribuited on many fixtures

Ring with variable radius, filled. Ring with variable radius

Ring Open/Close (close/open) Filled Ring Open/Close (close/open)

Ring Opening (Closing) Filled Ring Opening (Closing)

Ring 1 + 4 Ring 1 + 3 Ring 1 + 2 Ring 4 Ring 3 Ring 2 Ring 1 Macro OFF

N.a.

0-126 = max to min speed,

c.cw rotation 127-128 = STOP 129-255 = min to max speed,

cw rotationt" 0-126 = c.cw rotation 127-128 = STOP 129-255 = cw rotationt

The value 0-126 or 129-255 change the rainbow angle offset (the orange starting angle). 0-126 = max to min speed,

c.cw rotation 127-128 = STOP 129-255 = min to max speed,

cw rotationt

0-126 = max to min speed,

Instant-on + fadeout. 127-128 = STOP. 129-255 = min to max speed,

FadeIn + FadeOut.

Fade or snap depending on fade channel.

0-255 = radius 0 = minimum 255 = maximum

0-126 = max to min speed,

Start closed 127-128 = STOP 129-255 = min to max speed,

Start opened"

0-126 = max to min speed,

Closing effect 127-128 = STOP 129-255 = min to max speed,

Opening effect

N.a. N.a.

N.a.

0-255 → angle offset from 0 to 360°

N.a.

0-255 → angle offset from 0 to 360°

0-255 → select pixel density

0-255 → select random distribution from 2 up to 20 fixtures

N.a. 0-255 → angle offset from 0 to 360°

0-9 → continuous 10-255 → random distribution of flash from 2 to 20 fixtures"

N.a. N.a.

*1: Random colors activation with foreground R,G,B,W = 0

PRELIMINARY

subject to change without prior notice

27

A.LEDA B-EYE

Macro Off

DMX channel value: from 0 to 7. No shape effects activated. Turns off any previously selected shape.

Static Rings

DMX channel value: from 8 to 14. The ring or rings used by the macro are turned on with the foreground colour (Shape Red+Shape Green+Shape blue+Shape White). Avaliable combinations: Ring 1 On, Ring 2 On, Ring 3 On (Aleda K10, K20 only), Ring 4 On (Aleda K20 only),Ring 1+2 On, Ring 1+3 On (Aleda K10, K20 only), Ring 1+4 On (Aleda K20 only). Dynamic Rings DMX channel

Dynamic Rings

DMX channel value: From 15 to 18. The rings used by the macro are turned on sequentially, simulating an opening , closing or both. The Shape Speed channel increases the speed from 126 (min speed) to 0 (max speed) for the closing and closing/opening effects and from 129 (min speed) to 255 (max speed) for the opening and opening/closing effects. With DMX value = 127 or 128 the macro stays still. The Shape Offset channel defines the macro effect distribution over a number of fixtures (affects also the behavior of a single fixture) Dmx values from 0 to 9: continous distribution; Dmx values from 10 to 255 random distribution of flash from 2 to 20 fixtures. If foreground colors are all set to 0, the Random-Colors mode is activated. The color used by the macro changes at every restart.

Rings with variable radius

DMX channel value: 19 - 20. The Shape Speed channel defines the ring radius: 0 = min, 255 = max. Random pixels DMX

Random pixels

DMX channel value: 21 – 22. Leds are turned on and off randomly. The Shape Speed channel increases the speed and defines the fade effect for the leds: from 126 (min speed) to 0(max speed) with a Instant-on/ fade-out led effect, and from 129 (min speed) to 255 (max speed)with a fade-in + fade-out led effect. At a DMX value of 127 and 128 the macro stays still. For macro 21 the Shape Offset channel defines leds random distribution from 0 (2 fixtures) to 255 over a set of fixtures (20 fixtures). For macro 22 the Shape Offset channel defines pixels density from 0 (min density) to 255 (max density). If foreground colors are all set to 0 the Random-Colors mode is activated. The Shape Smoothing channel adjusts the fading effect applied to the macro movement

Rainbows

DMX channel value: 23 – 24 . It simulates a rainbow effect. The Shape Speed channel increases the speed and defines the rotation : from 126 (min speed) to 0 (max speed) counter clock wise rotation and from 129 (min speed) to 255 (max speed) clock wise rotation. With DMX value 127 or 128 the macro stays still. For the macro 24 (Rainbow with fixed speed) the Shape Speed channel also defines angle offset (the orange sector starting angle).

Rotating shapes

DMX channel value: from 25 to 31. Shapes avaliable: Fan (3 arms), Bar (2 arms), Half Moon, Triangle, Two rotating bars of different colors, Two rotating arcs of different colors, Two rotating arcs of different colors and direction. The Shape Speed channel increases the speed and defines the rotation : from 126 (min speed) to 0 (max speed) counter clock wise rotation and from 129 (min speed) to 255 (max speed) clock wise rotation. With DMX value 127 or 128 the macro stays still. The Shape Offset channel defines the angle offset from 0 (0 degree) to 255 (360 degree).

Continue

➔

PRELIMINARY

subject to change without prior notice

28

A.LEDA B-EYE

• ZOOM

BIT EFFECT

255

WIDE BEAM

0

NARROW BEAM

• SHAPE R G B W

BIT

EFFECT

2550COLOUR INSERTED

COLOUR EXCLUDED

• SHAPE INTENSITY

BIT EFFECT

2550COLOUR INSERTED

COLOUR EXCLUDED

• BACKGROUND INTENSITY

BIT

EFFECT

2550COLOUR INSERTED

COLOUR EXCLUDED

• SHAPE SMOOTHING

BIT EFFECT

246-255

245 244 243

18 17 16

0-15

Smooth, fading curve with automatic gamma * Smooth, fading curve gamma 2 Smooth, fading curve gamma 1,993 Smooth, fading curve gamma 1,986

Smooth, fading curve gamma 0,513 Smooth, fading curve gamma 0,506 Smooth, fading curve gamma 0,5 Snap

* Automatic gamma is calculated based on background intensity to auto-adapt the

shape’s fade.

1,000

0,900

0,800

0,700

0,600

0,500

0,400

0,300

0,200

0,100

0,000 0,100 0,200 0,300 0,400 0,500 0,600 0,700 0,800 0,900 1,000

Gamma Curve

DMX BIT

pixel colour distribution

pixel power

16

Fading gamma

0,500

1,000

0,900

0,800

0,700

0,600

0,500

0,400

0,300

0,200

0,100

0,000 0,100 0,200 0,300 0,400 0,500 0,600 0,700 0,800 0,900 1,000

Gamma Curve

DMX BIT

pixel colour distribution

pixel power

92

Fading gamma

0,997

1,000

0,900

0,800

0,700

0,600

0,500

0,400

0,300

0,200

0,100

0,000 0,100 0,200 0,300 0,400 0,500 0,600 0,700 0,800 0,900 1,000

Gamma Curve

DMX BIT

pixel colour distribution

pixel power

245

Fading gamma

2,000

PRELIMINARY

subject to change without prior notice

29

A.LEDA B-EYE

• SHAPE TRANSITION

BIT FADING TIME

4000 ms 3970 ms 3950 ms 3920 ms 3890 ms 3860 ms 3840 ms 3810 ms 3780 ms 3760 ms 3730 ms 3700 ms 3680 ms 3650 ms 3630 ms 3600 ms 3570 ms 3550 ms 3520 ms 3500 ms 3470 ms 3440 ms 3420 ms 3390 ms 3370 ms 3340 ms 3320 ms 3290 ms 3270 ms 3240 ms 3220 ms 3190 ms 3170 ms 3140 ms 3120 ms 3100 ms 3070 ms 3050 ms 3020 ms 3000 ms 2970 ms 2950 ms 2930 ms 2900 ms 2880 ms 2860 ms 2830 ms 2810 ms 2790 ms 2760 ms 2740 ms 2720 ms 2690 ms 2670 ms 2650 ms 2620 ms

255 254 253 252 251 250 249 248 247 246 245 244 243 242 241 240 239 238 237 236 235 234 233 232 231 230 229 228 227 226 225 224 223 222 221 220 219 218 217 216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200

BIT FADING TIME

2600 ms 2580 ms 2560 ms 2530 ms 2510 ms 2490 ms 2470 ms 2450 ms 2420 ms 2400 ms 2380 ms 2360 ms 2340 ms 2320 ms 2290 ms 2270 ms 2250 ms 2230 ms 2210 ms 2190 ms 2170 ms 2150 ms 2130 ms 2110 ms 2090 ms 2070 ms 2050 ms 2020 ms 2000 ms 1980 ms 1960 ms 1950 ms 1930 ms 1910 ms 1890 ms 1870 ms 1850 ms 1830 ms 1810 ms 1790 ms 1770 ms 1750 ms 1730 ms 1710 ms 1700 ms 1680 ms 1660 ms 1640 ms 1620 ms 1600 ms 1590 ms 1570 ms 1550 ms 1530 ms 1510 ms 1500 ms

199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144

BIT FADING TIME

1480 ms 1460 ms 1440 ms 1430 ms 1410 ms 1390 ms 1380 ms 1360 ms 1340 ms 1330 ms 1310 ms 1290 ms 1280 ms 1260 ms 1240 ms 1230 ms 1210 ms 1200 ms 1180 ms 1160 ms 1150 ms 1130 ms 1120 ms 1100 ms 1090 ms 1070 ms 1060 ms 1040 ms 1030 ms 1010 ms 1000 ms

980 ms

970 ms

950 ms

940 ms

930 ms

910 ms

900 ms

880 ms

870 ms

860 ms

840 ms

830 ms

820 ms

800 ms

790 ms

780 ms

770 ms

750 ms

740 ms

730 ms

710 ms

700 ms

690 ms

680 ms

670 ms

143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100

99 98 97 96 95 94 93 92 91 90 89 88

BIT FADING TIME

650 ms 640 ms 630 ms 620 ms 610 ms 600 ms 590 ms 570 ms 560 ms 550 ms 540 ms 530 ms 520 ms 510 ms 500 ms 490 ms 480 ms 470 ms 460 ms 450 ms 440 ms 430 ms 420 ms 410 ms 400 ms 390 ms 380 ms 370 ms 360 ms 350 ms 340 ms 330 ms 320 ms 310 ms 300 ms 290 ms 280 ms 270 ms 260 ms 250 ms 240 ms 230 ms 220 ms 210 ms 200 ms 190 ms 180 ms 170 ms 160 ms 150 ms 140 ms 130 ms 120 ms 110 ms 100 ms No fade

87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62

60-61

59 58 57 56

54-55

53 52 51

49-50

48 47

45-46

44

42-43

41 39-40 37-38 35-36

34 32-33 30-31 27-29 25-26 22-24 19-21 16-18 11-15

5-10

0-4

Continue

➔

PRELIMINARY

subject to change without prior notice

30

A.LEDA B-EYE

A.LEDA B-EYE K20

LED

1

2

3

45

6

7

8

9

10

11

12

13 14

15

16

17

18

19

20

21

22

23

24

25

26

27

28 29

30

31

32

33

34

35

36

37

LED

1

3

6

4

5

2

7

8

9

10

11

12

13 14

15

16

17

18

19

LED reference number for pixel mapping TILT: channel 16 at 80%

A.LEDA B-EYE K10

LED reference number for pixel mapping TILT: channel 16 at 80%

PRELIMINARY

subject to change without prior notice

CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035 -654311 - Fax +39-035-301876 - www.claypaky.it

PRELIMINARY 01/14 Cod. IST009/001 EN

PRELIMINARY

subject to change without prior notice

Clay Paky A.LEDA B-EYE K10, A.LEDA B-EYE K20, A.LEDA B-EYE K10 C61415, A.LEDA B-EYE K20 C61420 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual