Cla-Val 100-04 User Manual

100-04

• Built-in Automatic Check Valve

• Drip Tight, Positive Seating

• Globe or Angle Pattern

• Service Without Removal From Line

• Every valve factory-tested

The Cla-Val Model 100-04 Hy-Check Valve is a
hydraulically operated diaphragm valve with a built-in check
feature to prevent return flow. Available in globe or angle
pattern, it consists of a body, cover and diaphragm
assembly. The diaphragm assembly which is guided top
and bottom by a precision machined stem is the only
moving part.

A synthetic rubber disc retained on three and one half sides
forms a drip-tight seal with the renewable seat when
operating pressure is applied above the non-wicking
diaphragm. When pressure above the diaphragm is
relieved, the valve opens wide. The rate of closing or
opening can be controlled by modulating the flow into or out
of the cover chamber. When a pressure reversal occurs the
split stem will immediately allow the disc retainer assembly
to check closed regardless of the position of the

diaphragm.

The Model 100-04 is used on system applications such as
remote control, pressure regulation, solenoid control, etc.;
wherever a positive check feature is necessary to prevent
reverse flow. Its packless construction and simplicity of
design minimizes maintenance and assures a long
dependable service life.

100-04

Hy-Check Valve

Full Open Operation

When pressure in the cover
chamber is relieved to a zone of
lower pressure, the line pressure at
the valve inlet opens the valve,
allowing full flow.

Check Action

When a static condition or pressure
reversal occurs, the split stem design
allows the valve to instantly check
closed. Return flow is
prevented regardless of

the

diaphragm's position.

Tight Closing Operation

When pressure from the valve inlet
is applied to the cover chamber, the
valve closes drip-tight.

On-Off Control On-Off Control

Modulating

Control

Principle of Operation

Note: For optimum operation of built-in check feature, installation with stem vertically up is recommended.

MODEL

(Full Internal Port)

Epoxy Coating - suffix KC

This option NSF 61 Listed and FDA
approved, fusion bonded epoxy coating is
for use with cast iron, ductile iron or steel
valves. This coating is resistant to various
water conditions, certain acids, chemicals,
solvents and alkalies.

Epoxy coatings are
applied in accordance with AWWA coating
specifications C116-03.
Do not use with temperatures above

175° F

Viton

®

Rubber Parts- suffix KB

Optional diaphragm, disc and o-ring
fabricated with Viton®synthetic rubber. Viton

®

is well suited for use with mineral acids, salt
solutions, chlorinated hydrocarbons, and
petroleum oils; and is primarily used in high
temperature applications up to 250° F. Do
not use with epoxy coating above 175°F.

For assistance in selecting appropriate
valve options or valves manufactured
with special design requirements,
please contact our Regional Sales
Office or Factory.

Options

Specifications

Model 100-04

Operating Temp. Range

Available Sizes

Pattern Flanged

Globe 2" - 16"

Angle 3" - 16"

Fluids

-40° to 180° F

Component Standard Material Combinations

Body & Cover Ductile Iron Cast Steel Bronze

Available Sizes 2" - 16" 2" - 16" 2" - 16"

Disc Retainer &
Diaphragm Washer

Cast Iron Cast Steel Bronze

Trim: Disc Guide,
Seat & Cover Bearing

Bronze is Standard

Stainless Steel is optional

Disc Buna-N®Rubber

Diaphragm Nylon Reinforced Buna-N®Rubber

Stem, Nut & Spring Stainless Steel

For material options not listed, consult factory.
Cla-Val manufactures valves in more than 50 different alloys.

Materials

BOLT/HEX NUT (TYP)

COVER BEARING

UPPER DIAPHRAGM WASHER

SEAT

STUD/BOLT (TYP)

BODY

INLET

PIPE PLUG (TYP)

OUTLET

SEAT-O-RING

DISC GUIDE

DIAPHRAGM

UPPER STEM NUT

COVER

PIPE PLUG (TYP)

UPPER STEM

DISC GUIDE SCREW (TYP)

LOCK WASHER

LOWER STEM NUT

SPRING

LOWER STEM

SPRING

LOWER DIAPHRAGM WASHER

DISC

DISC RETAINER

Valve Body & Cover

Pressure Class

Flanged Threaded

Grade Material

ANSI

Standards*

150

Class

300

Class

End‡

Details

ASTM A536 Ductile Iron B16.42 250 400 400

ASTM A216-WCB Cast Steel B16.5 285 400 400

ASTM B62 Bronze B16.24 225 400 400

Note: * ANSI standards are for flange dimensions only.

Flanged valves are available faced but not drilled.

‡ End Details machined to ANSI B2.1 specifications.

Valves for higher pressure are available; consult factory for details

Pressure Ratings

(Recommended Maximum Pressure - psi)

Valve Size

Inches 2 3 4 6 8 10 12 14 16

mm.

50 80 100 150 200 250 300 350 400

C

V

Factor

Globe

Pattern

Gal./Min. (gpm.)

54 115 200 440 770 1245 1725 2300 2940

Litres/Sec. (l/s.)

13 27.6 48 105.6 184.8 299 414 552 706

Angle

Pattern

Gal./Min. (gpm.)

61 139 240 541 990 1575 2500* 3060* 4200*

Litres/Sec. (l/s.)

14.6 33.4 58 130 238 378 600 734.4 1008

Equivalent

Length

of

Pipe

Globe

Pattern

Feet (ft.)

51 85 116 211 291 347 467 422 503

Meters (m.)

15.5 25.9 35.3 64.2 88.6 105.8 142.4 128.6 153.6

Angle

Pattern

Feet (ft.)

40 58 80 139 176 217 222* 238* 247*

Meters (m.)

12.1 17.8 24.5 42.5 53.6 66.1 67.8 72.7 75.2

K

Factor

Globe Pattern

5.6 6.0 5.9 6.2 6.1 5.8 6.1 5.0 5.2

Angle Pattern

4.4 4.1 4.1 4.1 3.7 3.6 2.9 2.8 2.6

Liquid Displaced from

Cover Chamber When

Valve Opens

Fl. Oz

— — — — — — — — —

U.S. Gal.

0.3 .08 .17 .53 1.26 2.51 4.0 6.5 9.6

ml

121 303 643 — — — — — —

Litres

— — — 2.0 4.8 9.5 15.1 24.6 36.2

10 20 30 40 60 80 100 200 500 1000 2000 5000 10,000 20,000 50,000

1

2

3

4

6

8

10

20

30

40

60

80

100

53

Angle Valve Sizes (Inches)

Globe Valve Sizes (Inches)

4

6

810

12

12

46810

14

16

16

Pressure Drop — psi

14

Flow Rate gpm (water)

3

3

2

2

Model 100-04 Flow Chart (Based on normal flow through a wide open valve)

K =

894d

4

C

2

v

L =

K
12 f

K Factor (Resistance Coefficient)

The Value of K is calculated from the formula:
(U.S. system units)

Equivalent Length of Pipe

Equivalent lengths of pipe (L) are determined from the formula:
(U.S. system units)

Fluid Velocity

Fluid velocity can be calculated from the following formula:
(U.S. system units)

d

V =

.4085 Q

2

d

C

V

Factor

Formulas for computing C Factor, Flow (Q) and Pressure Drop

V

( P):

C

V

=

Q

P

C

V

=

Q

P

C

V

=

Q

P

2

V

Where:

U.S. (gpm) @ 1 psi differential at 60 F water

(l/s) @ 1 bar (14.5 PSIG) differential

or

at 15 C water

inside pipe diameter of Schedule 40 Steel Pipe (inches)

friction factor for clean, new Schedule 40 pipe

(dimensionless) (from Cameron Hydraulic Data,

18th Edition, P 3-119)

Resistance Coefficient (calculated)

Equivalent Length of Pipe (feet)

Flow Rate in U.S. (gpm) or (l/s)

Fluid Velocity (feet per second) or (meters per second)

Pressure Drop in (psi) or (bar)

=

=

=

=

=

=

=

=

=

P

V

Q

L

K

f

d

C

Functional Data Model 100-04

*Estimated

CLA-VAL

Copyright Cla-Val 2011 Printed in USA Specifications subject to change without notice.

P.O. Box 1325 • Newport Beach, CA 92659-0325 • Phone: [phone] • Fax: [phone] • E-mail: [e-mail] • Website cla-val.com

©

Dimensions

Model 100-04

Service

Cla-Val Control Valves operate with maximum efficiency when mounted in horizontal piping with the main valve cover UP, however, other
positions are acceptable. Due to component size and weight of 8 inch and larger valves, installation with cover UP is advisable. We recommend
isolation valves be installed on inlet and outlet for maintenance. Adequate space above and around the valve for service personnel should be
considered essential. A regular maintenance program should be established based on the specific application data. However, we recommend a
thorough inspection be done at least once a year. Consult factory for specific recommendations.

E-100-04 (R-8/2011)

Valve Size (Inches) 2 3 4 6 8 10 12 14 16
A 150 ANSI

9.38 12.00 15.00 20.00 25.38 29.75 34.00 39.00 41.38

AA 300 ANSI

10.00 13.25 15.62 21.00 26.38 31.12 35.50 40.50 43.50

B Dia.

6.62 9.12 11.50 15.75 20.00 23.62 28.00 32.75 35.50

C Max.

6.50 8.19 10.62 13.38 16.00 17.12 20.88 24.19 25.00

D 150 ANSI

4.75 6.00 7.50 10.00 12.69 14.88 17.00 19.50 20.69

DD 300 ANSI

5.00 6.38 7.81 10.50 13.19 15.56 17.75 20.25 21.75

E

1.50 2.56 3.19 4.31 5.31 9.25 10.75 12.62 15.50

F 150 ANSI

2.50 3.75 4.50 5.50 6.75 8.00 9.50 10.50 11.75

FF 300 ANSI

3.25 4.13 5.00 6.25 7.50 8.75 10.25 11.50 12.75

G 150 ANSI

3.25 4.00 5.00 6.00 8.00 8.62 13.75 14.88 15.69

GG 300 ANSI

3.25 4.38 5.31 6.50 8.50 9.31 14.50 15.62 16.50

H NPT Body Tapping

.375 .50 .75 .75 1 1 1 1 1

J NPT Cover Center Plug

.50 .50 .75 .75 1 1 1.25 1.50 2

K NPT Cover Tapping

.375 .50 .75 .75 1 1 1 1 1
Valve Stem Internal
Thread UNF

10-32

1

⁄4-28

1

⁄4-28

3

⁄8-24

3

⁄8-24

3

⁄8-24

3

⁄8-24

3

⁄8-24

1

⁄2-20

Stem Travel

0.6 0.8 1.1 1.7 2.3 2.8 3.4 4.0 4.5

Approx. Ship Wt. Lbs.

35 70 140 285 500 780 1165 1500 2265

Valve Size (mm) 50 80 100 150 200 250 300 350 400
A 150 ANSI

238 305 381 508 645 756 864 991 1051

AA 300 ANSI

254 337 397 533 670 790 902 1029 1105

B Dia.

168 232 292 400 508 600 711 832 902

C Max.

165 208 270 340 406 435 530 614 635

D 150 ANSI

121 152 191 254 322 378 432 495 526

DD 300 ANSI

127 162 200 267 335 395 451 514 552

E

38 65 81 109 135 235 273 321 394

F 150 ANSI

76 95 114 140 171 203 241 267 298

FF 300 ANSI

83 105 127 159 191 222 260 292 324

G 150 ANSI

83 102 127 152 203 219 349 378 399

GG 300 ANSI

89 111 135 165 216 236 368 397 419

H NPT Body Tapping

.375 .50 .75 .75 1 1 1 1 1

J NPT Cover Center Plug

.50 .50 .75 .75 1 1 1.25 1.50 2

K NPT Cover Tapping

.375 .50 .75 .75 1 1 1 1 1

Valve Stem Internal
Thread UNF

10-32

1

⁄4-28

1

⁄4-28

3

⁄8-24

3

⁄8-24

3

⁄8-24

3

⁄8-24

3

⁄8-24

1

⁄2-20

Stem Travel

15 20 28 43 58 71 86 102 114

Approx. Ship Wt. Kgs.

16 32 64 129 227 354 528 726 1027

G

GG

D

Inlet

DD

F

100-04

Flanged

A

E

C

(MAX)

K

J

H

Inlet

Outlet

AA

B

(Diameter)

Cla-Val Product

Identification

Proper Identification

For ordering repair kits, replacement parts, or for
inquiries concerning valve operation, it is important to
properly identify Cla-Val products already in service
by including all nameplate data with your inquiry.
Pertinent product data includes valve function, size,
material, pressure rating, end details, type of pilot
controls used and control adjustment ranges.

Identification Plates

For product identification, cast-in body markings are
supplemented by identification plates as illustrated on
this page. The plates, depending on type and size of
product, are mounted in the most practical position. It

is extremely important that these identification
plates are not painted over, removed, or in any
other way rendered illegible.

INLET
EINTRITT
ENTREE
ENTRADA

SIZE &
CAT NO.

STOCK
NO.

CODE

MFD. BY CLA-VAL
NEWPORT BEACH, CALIF, U.S.A.

RESERVOIR

END

I

N

L

E

T

I

N

L

E

T

SIZE &
CAT NO.

STOCK
NO.

FLOW

MFD. BY CLA-VAL NEWPORT BEACH, CALIF. U.S.A.

CODE

C

®

™

SIZE &
CAT NO.

STOCK
NO.

SPRING
RANGE

MFD. BY CLA-VAL NEWPORT BEACH, CALIF. U.S.A.

SIZE &
CAT NO.

STOCK
NO.

CODE

MFD. BY CLA-VAL

NEWPORT BEACH, CALIF.

U.S.A.

C

®

™

DO NOT REMOVE

THIS VALVE HAS BEEN MODIFIED
SINCE ORIGINAL SHIPMENT FROM
FACTORY. WHEN ORDERING PARTS
AND/ OR SERVICE SUPPLY DATA FROM
THIS PLATE & ALL OTHER PLATES ON
ORIGINAL VALVE.

REDUCED PRESSURE BACKFLOW PREVENTION DEVICE

STK.
NO.

SER.
NO.

CAT.

NO.

RP

-4

CLA-VAL

NEWPORT BEACH, CA.

This brass plate appears on valves sized 21/2" and larger

and is located on the top of the inlet flange.

These two brass plates appear on 3/8", 1/2", and 3/4" size

valves and are located on the valve cover.

These two brass plates appear on threaded valves

1" through 3" size or flanged valves 1" through 2".

It is located on only one side of the valve body.

This brass plate appears on altitude valves only and is

found on top of the outlet flange.

This brass plate is used to identify pilot control valves.

The adjustment range is stamped into the plate.

This tag is affixed to the cover of the pilot control valve.

The adjustment range appears in the spring range section.

This aluminum plate is included in pilot system

modification kits and is to be wired to the new pilot

control system after installation.

This brass plate is used on our backflow prevention

assemblies. It is located on the side of the Number Two

check (2" through 10"). The serial number of the

assembly is also stamped on the top of the inlet flange of

the Number One check.

How to Order

HOW TO ORDER

Because of the vast number of possible configurations and
combinations available, many valves and controls are not
shown in published product and price lists. For ordering
information, price and availability on product that are not listed,
please contact your local Cla-Val office or our factory office
located at:

SPECIFY WHEN ORDERING

• Model Number • Valve Size

• Globe or Angle Pattern • Threaded or Flanged

• Adjustment Range • Body and Trim Materials
(As Applicable) • Optional Features

• Pressure Class

UNLESS OTHERWISE SPECIFIED

• Globe or angle pattern are the same price

• Ductile iron body and bronze trim are standard

• X46 Flow Clean Strainer or X43 “Y” Strainer are included

• CK2 Isolation Valves are included in price on 4" and larger
valve sizes (6" and larger on 600 Series)

P. O. Box 1325

Newport Beach, California 92659-0325

[phone]

FAX [phone]

LIMITED WARRANTY

Automatic valves and controls as manufactured by Cla-Val are warranted
for three years from date of shipment against manufacturing defects in
material and workmanship that develop in the service for which they are
designed, provided the products are installed and used in accordance
with all applicable instructions and limitations issued by Cla-Val.
Electronic components manufactured by Cla-Val are warranted for one
year from the date of shipment.

We will repair or replace defective material, free of charge, that is returned
to our factory, transportation charges prepaid, if upon inspection, the
material is found to have been defective at time of original shipment. This
warranty is expressly conditioned on the purchaser’s providing written
notification to Cla-Val immediate upon discovery of the defect.

Components used by Cla-Val but manufactured by others, are warranted
only to the extent of that manufacturer’s guarantee.

This warranty shall not apply if the product has been altered or repaired by
others, Cla-Val shall make no allowance or credit for such repairs or
alterations unless authorized in writing by Cla-Val.

DISCLAIMER OF WARRANTIES AND
LIMITATIONS OF LIABILITY

The foregoing warranty is exclusive and in lieu of all other
warranties and representations, whether expressed, implied, oral or
written, including but not limited to any implied warranties or
merchantability or fitness for a particular purpose. All such other
warranties and representations are hereby cancelled.

Cla-Val shall not be liable for any incidental or consequential loss,
damage or expense arising directly or indirectly from the use of the
product. Cla-Val shall not be liable for any damages or charges for
labor or expense in making repairs or adjustments to the product.
Cla-Val shall not be liable for any damages or charges sustained in
the adaptation or use of its engineering data and services. No
representative of Cla-Val may change any of the foregoing or
assume any additional liability or responsibility in connection with
the product. The liability of Cla-Val is limited to material
replacements F.O.B. Newport Beach, California.

TERMS OF SALE

ACCEPTANCE OF ORDERS

All orders are subject to acceptance by our main office at Newport Beach, California.

CREDIT TERMS

Credit terms are net thirty (30) days from date of invoice.

PURCHASE ORDER FORMS

Orders submitted on customer’s own purchase order forms will be accepted only
with the express understanding that no statements, clauses, or conditions contained
in said order form will be binding on the Seller if they in any way modify the Seller’s
own terms and conditions of sales.

PRODUCT CHANGES

The right is reserved to make changes in pattern, design or materials when deemed
necessary, without prior notice.

PRICES

All prices are F.O.B. Newport Beach, California unless expressly stated otherwise on
our acknowledgement of the order. Prices are subject to change without notice. The
prices at which any order is accepted are subject to adjustment to the Seller’s price
in effect at the time of shipment. Prices do not include sales, excise, municipal, state
or any other Government taxes. Minimum order charge $100.00.

RESPONSIBILITY

We will not be responsible for delays resulting from strikes, accidents, negligence of
carriers, or other causes beyond our control. Also, we will not be liable for any
unauthorized product alterations or charges accruing there from.

RISK

All goods are shipped at the risk of the purchaser after they have been delivered by
us to the carrier. Claims for error, shortages, etc., must be made upon receipt of
goods.

EXPORT SHIPMENTS

Export shipments are subject to an additional charge for export packing.

RETURNED GOODS

1. Customers must obtain written approval from Cla-Val prior to returning any
material.

2. Cla-Val reserves the right to refuse the return of any products.

3. Products more than six (6) months old cannot be returned for credit.

4. Specially produced, non-standard models cannot be returned for credit.

5. Rubber goods such as diaphragms, discs, o-rings, etc., cannot be returned for
credit, unless as part of an unopened vacuum sealed repair kit which is less
than six months old.

6. Goods authorized for return are subject to a 35% ($100 minimum) restocking
charge and a service charge for inspection, reconditioning, replacement of
rubber parts, retesting, repainting and repackaging as required.

7. Authorized returned goods must be packaged and shipped prepaid to Cla-Val,
1701 Placentia Avenue, Costa Mesa, California 92627.

PO Box 1325 Newport Beach CA 92659-0325

Phone: [phone] Fax: [phone]

C

LA-VAL

CLA-VAL CANADA CLA-VAL EUROPE

4687 Christie Drive
Beamsville, Ontario
Canada L0R 1B4
Phone: [phone]
Fax: [phone]

Chemin dés Mesanges 1
CH-1032 Romanel/
Lausanne, Switzerland
Phone: [phone]
Fax: [phone]

©COPYRIGHT CLA-VAL 2011 Printed in USA

Specifications subject to change without notice.

www.cla-val.com

E-Product I.D. (R-3/2011)

Represented By:

Complete Replacement Diaphragm Assemblies for 100-01 and 100-20 Hytrol Main Valves

For:

Hytrol Main Valves with Ductile Iron, Bronze Trim Materials—125/150 Pressure Class Only.
FACTORY ASSEMBLED
Includes: Stem, Disc Guide, Disc, Disc Retainer, Spacer Washers, Diaphragm, Diaphragm Washer
and Stem Nut.

3/8"

1/2" - 3/4"

1"

1 1/4"-1 1/2"

2"

2 1/2"

3"
4"

(Also 81-01 )
(Also 81-01 )

N/A
N/A
N/A
N/A
N/A
N/A

C2524B

C2525J

6"

8"
10"
12"
14"
16"
20"
24"

40456G
45276D

81752J

85533J
89067D
89068B

N/A
N/A

33273E
40456G
45276D

81752J

N/A

85533J
89068B
89068B

Valve

Size

Valve

Size

49097K
C2518D
C2520K

C2522 F

C2524B
C2523D

C2525J

33273E

100-01 100-20

Diaphragm Assembly

Stock Number

100-01 100-20

Diaphragm Assembly

Stock Number

3/8"

1/2" - 3/4"

1"

1 1/4" - 1 1/2"

2"

2 1/2"

3"
4"
6"

8"
10"
12"
14"
16"
20"
24"

(Also 81-01 )
(Also 81-01 )

N/A
N/A
N/A
N/A
N/A

N/A
9169805A
9169812G
9169813E
9169815K
9817901D
9817902B

N/A
9817903K
9817905E
9817905E

3/8"

1/2" - 3/4"

1"

1 1/4” - 1 1/2"

2"

2 1/2"

3"
4"
6"
8"

9169806J
9169807G
9169808E
9169809C
9169810A

9169817F
9169818D
9169819B
9169820K
9169834A

N/A
N/A
N/A
N/A
N/A

N/A
9169810A
9169818D
9169819B
9169820K

Valve

Size

Valve

Size

9169801K
9169802H
9169803F
9169804D
9169805A
9169811J
9169812G
9169813E
9169815K
9817901D
9817902B
9817903K
9817904H
9817905E

N/A

9817906C

100-01 100-20

Repair Kit

Stock Number

100-01 100-20

Repair Kit

Stock Number

Repair Kits for 100-01/100-20 Hytrol Valves

For:

Hytrol Main Valves—125/150 Pressure Class Only.

Includes: Diaphragm, Disc (or Disc Assembly) and spare Spacer Washers.

(Also 81-01 )
(Also 81-01 )

REPAIR KITS

When ordering, please give complete nameplate data of the valve and/or control being repaired.

MINIMUM ORDER CHARGE APPLIES.

Buna-N®Standard Material

Viton (For KB Valves)

MODEL

INSTALLATION / OPERATION / MAINTENANCE

Repair Kits for 100-04/100-23 Hy-Check Main Valves

For:

Hy-Check Main Valves—125/150 Pressure Class Only

Includes: Diaphragm, Disc and O-Rings and full set of spare Spacer Washers.

Larger Sizes: Consult Factory.

Repair Kits for 100-02/100-21 Powertrol and 100-03/100-22 Powercheck Main Valves

For:

Powertrol and Powercheck Main Valves—125/150 Pressure Class Only

Includes: Diaphragm, Disc (or Disc Assembly) and O-rings and full set of spare Spacer Washers.

Repair Kits for Pilot Control Valves (In Standard Materials Only)

Includes: Diaphragm, Disc (or Disc Assembly), O-Rings, Gaskets or spare Screws as appropriate.

Repair Assemblies (In Standard Materials Only)

CLA-VAL

Copyright Cla-Val 2011 Printed in USA Specifications subject to change without notice.

P.O. Box 1325 • Newport Beach, CA 92659-0325 • Phone: [phone] • Fax: [phone] • E-mail: [e-mail] • Website cla-val.com

©

N-RK (R-3/2011)

Valve

Size

Kit Stock Number

100-02

Valve

Size

Kit Stock Number

100-02 & 100-03 100-21 & 100-22

3

⁄8”

9169901H

2

1

⁄2”

9169910J N/A

1

⁄2” &3⁄4”

9169902F

3”

9169911G 9169905J

1” 9169903D

4”

9169912E 9169911G

1

1

⁄4” &11⁄2”

9169904B

6”

9169913C 9169912E

2” 9169905J

8”

99116G 9169913C

10”

9169939H 99116G

12"

9169937B 9169939H

Valve

Size

Kit Stock Number

Valve

Size

Kit Stock Number

100-04 100-23 100-04 100-23

4” 20210901B N/A 12” 20210905H 20210904J
6” 20210902A 20210901B 14” 20210906G N/A
8” 20210903K 20210902A 16” 20210907F 20210905H

10” 20210904J 20210903K 20” N/A 20210907F

24” N/A 20210907F

BUNA-N

®

(Standard Material)

VITON (For KB Controls)

Pilot

Control

Kit

Stock

Number

Pilot

Control

Kit

Stock

Number

Pilot

Control

Kit

Stock

Number

CDB 9170006C CFM-7 1263901K CDB-KB 9170012A
CDB-30 9170023H CFM-7A 1263901K CRA-KB N/A
CDB-31 9170024F CFM-9 12223E

CRD-KB (w/bucking spring)

9170008J

CDB-7 9170017K

CRA (w/bucking spring)

9170001D CRL-KB 9170013J

CDH-2 18225D

CRD (w/bucking spring)

9170002B CDHS-2BKB 9170010E

CDHS-2 44607A

CRD (no bucking spring)

9170003K CDHS-2FKB 9170011C
CDHS-2B 9170004H CRD-18 20275401K CDHS-18KB (no bucking spring) 9170009G
CDHS-2F 9170005E CRD-22 98923G

102C-KB

1726202D
CDHS-3C-A2 24657K CRL (55F, 55L) 9170007A
CDHS-8A 2666901A CRL-4A 43413E
CDHS-18 9170003K CRL-5 (55B) 65755B
CDS-4 9170014G CRL-5A (55G) 20666E
CDS-5 14200A CRL-18 20309801C
CDS-6 20119301A CV 9170019F

Buna-N

®

CDS-6A 20349401C X105L (O-ring) 00951E
CFCM-M1 1222301C 102B-1 1502201F CRD Disc Ret. (Solid) C5256H
CFM-2 12223E 102C-2 1726201F CRD Disc Ret. (Spring) C5255K

102C-3 1726201F

Control Description Stock Number

CF1-C1 Pilot Assembly Only 89541H
CF1-Cl Complete Float Control less Ball and Rod 89016A
CFC2-C1 Disc, Distributor and Seals 2674701E
CSM 11-A2-2 Mechanical Parts Assembly 97544B
CSM 11-A2-2 Pilot Assembly Only 18053K
33A 1" Complete Internal Assembly and Seal 2036030B
33A 2" Complete Internal Assembly and Seal 2040830J

When ordering, please give complete nameplate data of the valve and/or control being repaired. MINIMUM ORDER CHARGE APPLIES

Larger Sizes: Consult Factory.