Page 1
WELDING EARTH CLAMPS
MODEL NO: EC200, EC300 & EC500
PART NO: 8135435, 8135440 & 8135445
USER INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC 0624
Page 2
INTRODUCTION
Thank you for purchasing this CLARKE product.
Please follow the instructions given. In doing so you will ensure the safety of
yourself and that of others around you and you can look forward to the
product giving you long and satisfactory service.
.Always read the safety warnings before use.
Model No EC200 EC300 EC500
Part No 8135435 8135440 81354345
Amperage at 30% Duty 500A
Amperage at 40% Duty 300A
Amperage at 60% Duty 200A
Cable Section
25-35mm
2
25-50mm235-70mm
Tested in accordance with BS EN 60974-13:2021.
WARNING: ELECTRIC SHOCK CAN KILL. DO NOT TOUCH LIVE ELECTRICAL PARTS
WITH BARE HANDS AND DO NOT USE WET OR DAMP GLOVES OR CLOTHING. USE
THIS CLAMP ONLY FOR ELECTRICAL WELDS AND FOR RETURN CURRENT OF THE
WELDING CIRCUIT.
For electrical conductivity make sure that the welding cable is properly
connected to the clamp. The end of the cable must be properly sheathed
and secured by tightening the special pins or the bolt of the cable clamp
plate.
Use the cable section indicated above.
Make sure that the clamp is properly connected to the workpiece to be
welded, cleaning the contact area adequately.
Welding gloves must be worn when using this clamp. DO NOT use at a higher
amperage than the approved amperage rating.
DO NOT use this clamp for purposes other than those specified. If it is
damaged, the clamp must be replaced.
Cleaning and repair of the welding machine MUST BE CARRIED OUT with the
machine SWITCHED OFF and disconnected from the electrical supply.
2
2
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 3
The following safety symbols are to be found on this product.
Danger of electric shock
Spark hazard - wear eye protection
Heat hazard - wear protective gloves
Read the user manual
GENERAL SAFETY WARNINGS
1. When welding indoors, ensure there is adequate ventilation.
2. NEVER look at an electric arc without protection. A welding headshield or
helmet with appropriate lenses must be used when welding. All persons
present must always use a proper welding face shield with suitable lenses.
3. After welding, ALWAYS check that the area is free of any sparks or glowing
embers.
4. When necessary, use identical replacement parts to ensure that the safety
of the product is maintained.
ENVIRONMENTAL PROTECTION
DO NOT dispose of welding products with general household waste. They
contain valuable raw materials and should be disposed of appropriately at a
recognised disposal facility.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for its intended purpose. Faulty goods
should be returned to their place of purchase, no product can be returned to
us without prior permission.
This guarantee does not effect your statutory rights.
3
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 4
ACCESSORIES FROM THE CLARKE CATALOGUE
4
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 5
DECLARATION OF CONFORMITY - EC200
5
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 6
DECLARATION OF CONFORMITY - EC300
6
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 7
DECLARATION OF CONFORMITY - EC500
7
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 8
Loading...