Page 1
4-SHELF INDUSTRIAL BOLTLESS SHELVING
MODEL NO: CS4600BO & CS41000BO
PART NO: SEE TABLE PAGE 2
ASSEMBLY INSTRUCTIONS
GC0416
Page 2
INTRODUCTION
Thank you for purchasing this CLARKE Shelving Unit.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
Please keep these instructions in a safe place for future reference.
SCOPE
These instructions cover the following models
Description Model Part Number
4-Shelf 600kg Boltless Shelving (Blue/orange) CS4600BO 6600728
4-Shelf 1000kg Boltless Shelving (Blue/orange) CS41000BO 6600730
SPECIFICATIONS
Model Dimension
(W x D x H)
4-Shelf 600kg
Shelving
4-Shelf 1000kg
Shelving
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
2000 x 600 x 2000 mm 71.8 kg 600 kg
2000 x 800 x 1800 mm 72.3 kg 1000 kg
2
Weight
(Empty)
Load per
shelf
(evenly
distributed)
Page 3
INVENTORY
No Description Quantity
APost 4
BLong Beam 8
CShort Beam 6
D Support Beam 20
E Shelf 4
F Foot (already fitted) 4
3
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 4
ASSEMBLY INSTRUCTIONS
1. Assemble on a strong, level surface. Avoid assembly on a domestic carpet.
2. Use a cloth or softwood block to protect the surface finish of the product
when using a mallet. Strike the flat surface of each beam to prevent
damage to the beam.
3. Always ensure that the rivets sit at the bottom of the keyhole slots.
4. It is recommended that the assembly should be done by two persons.
5. Always wear gloves when assembling these units.
6. The shelving unit is not recommended for outdoor use.
TOOLS REQUIRED
• Rubber mallet or hammer
• Protective cloth/wood block
ASSEMBLY PROCEDURE
1. Assemble the supporting beams as follows.
2. The tabs of the beams will often
enter the slots fully using just firm
hand pressure but if they are too
tight, you may require a rubber
mallet to assist. If so, always use a
cloth to protect the paint finish.
3. Tap gently with the mallet to drive
the tabs of the beams fully into
the slots in the post. Always strike
the edge close to the post.
4. Use the short beams (C) to
connect the front and rear posts
together as in Fig 2.
• The edge with the wider flange
should be installed uppermost to
support the shelf.
• Leave a gap of 220mm below the
bottom beam and the ground.
Leave 100mm gap from the top
beam and the top of the posts.
4
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 5
5. Repeat this again to create the other end assembly, making sure that the
corresponding beams are at the same height.
6. Join the two end assemblies
together with the long beams (B)
as in Fig 3.
• The beams should be spaced
equally with a gap of 500mm
between each one and the top
beam will be level with the top of
the posts.
7. Connect the support beams (E) to
the long beams (C). First bend the
tabs 90 degrees to pass them
through the slots in the long
beams.
• The tab initially lays flat against the
long beam (C).
8. Next, bend the tab back through
180 degrees to grip the long
beam.
• Use a screwdriver or similar tool to
bend the tabs.
9. Finally bend the tab again through
90 degrees the opposite way, to
seat tightly against the support
beam.
• Ensure there is no movement
between the beams.
10. Lay the shelf panels (E) into
position.
5
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 6
11. We recommend that the racking
be secured to an adjacent wall
using typical wall insert plugs and
screws (not supplied) aligned with
the assembly slots in the posts.
GENERAL SAFETY RULES
1. Always maintain equipment in good condition for the best/safest
performance.
2. Never exceed the maximum load for these shelving units as stated in the
specification.
3. Never use these units if they are damaged.
4. Always load small, stable items on the top shelves, heavier and bulky items
should be stored on the lower shelves.
5. Always distribute heavy loads evenly across the shelves.
6. Always locate on a strong, level, floor surface. Allow adequate working
space
ENVIRONMENTAL PROTECTION
Do not dispose of old products or damaged parts with general household
waste. All tools, accessories and packaging no longer required should be
sorted, taken to a recycling centre and disposed of appropriately.
6
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 7
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
7
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 8
Loading...