Page 1
SERVICE:
0504
PART NUMBER: 1801498
MODEL: CHT498
CLARKE GUARANTEE
PARTS:
or e-mail as follows:
020 8988 7400
PARTS & SERVICE TEL:
1 off Adapter/Bit Holder.
4 off Pillips Bits
4 off Hex Bits.
5 off Slotted Bits.
1 off Impact Driver.
1 off Blow Mould Carry Case.
This CLARKE product is guaranteed
against faulty manufacture for a
period of 12 months from the date
of purchase. Please keep your
receipt as proof of purchase.
This guarantee is invalid if the
product is found to have been
abused or tampered with in any way,
or not used for the purpose for which
it was intended.
Faulty goods should be returned to
their place of purchase, no product
can be returned to us without prior
permission.
This guarantee does not effect your
statutory rights.
CONTENTS
statutory rights.
This guarantee does not effect your
permission.
can be returned to us without prior
their place of purchase, no product
Faulty goods should be returned to
it was intended.
or not used for the purpose for which
abused or tampered with in any way,
product is found to have been
This guarantee is invalid if the
receipt as proof of purchase.
of purchase. Please keep your
period of 12 months from the date
against faulty manufacture for a
This CLARKE product is guaranteed
CLARKE GUARANTEE
MODEL: CHT498
PART NUMBER: 1801498
0504
CONTENTS
1 off Blow Mould Carry Case.
1 off Impact Driver.
5 off Slotted Bits.
4 off Hex Bits.
4 off Phillips Bits
1 off Adapter/Bit Holder.
PARTS & SERVICE TEL:
020 8988 7400
or e-mail as follows:
PARTS:
SERVICE:
Page 2
WARNING:
As with all tools, there are certain hazards involved with their operation and use.
Exercising respect and caution will considerably lessen the risk of personal injury.
However, if normal safety precautions are overlooked or ignored, personal injury
to the operator or damage to property, may result.
1.
ALWA YS
it.Read and become familiar with the entire operating instructions.
2.
ALWA YS
ensure that it will operate properly, and perform its intended function.
3.
ALWAYS
eyeglasses do not have impact resistant lenses, they are not safety glasses.
4.
ALWAYS
5.
ALWAYS
provided. Ensure that lighting is placed so that you will not be working in your own shadow.
6.
ALWA YS
7.
ALWAYS
8.
ALWAYS
accidents are caused by carelessness due to familiarity.
9.
ALWAYS
wear rubber soled footwear. Keep floor clear of oil, scrap wood etc.
USING THE TOOL
Select bit to be used,and insert into bit holder.
Adjust the tool for either loosening or tightening as required.
To do this, hold the tool in one hand, grip the bit holder with the
When finished, remove the bit and store tool and bit in carry case for reuse later.
The tool can be used to loosen and tighten hexagon head bolts etc, using high impact sockets
it is important only high impact bits and sockets are used with this tool, otherwise serious injury could be
caused, non high impact bits/sockets are likely to shatter and fly.
Please note that the details and specifications contained herein are correct at the time of going to print. However
learn the tools applications, limitations and the specific potential hazards peculiar to
check for damage. Before using the tool, any damaged part should be checked to
wear safety goggles, manufactured to the latest European Safety Standards. Everyday
keep work area clean. Cluttered areas and benches invite accidents.
ensure that adequate lighting is available. A minimum intensity of 300 lux should be
keep children away. All visitors should be kept a safe distance from the work area.
maintain tool in top condition. Keep tools clean for the best and safest performance.
concentrate on the job in hand, no matter how trivial it may seem. Be aware that
keep your proper footing and balance at all times - dont overreach. For best footing,
other depress and turn the bit holder in the direction of
arrow, L to loosen right hand threads or tighten left hand threads, and R to tighten
R/H or loosen L/H, turn the bit holder until it clicks into position.
L
R
CLARKE International reserve the right to change specifications at any time without prior notice.
If it is found hard to do this by hand, it is possible to carry out this
adjustment as follows, remove bit holder to reveal the ½
square drive, whilst holding the handle, rotate
the drive using a ½ spanner.
Turn clockwise.
Set the bit in screw head to be
turned, hold firmly in place applying
slight pressure in the direction the
screw is to be turned, firmly strike the
end of the handle with a hammer, the screw should move, if
not repeat above action until it does.
BIT HOLDER
ONLY,
CLARKE International reserve the right to change specifications at any time without prior notice.
Please note that the details and specifications contained herein are correct at the time of going to print. However
caused, non high impact bits/sockets are likely to shatter and fly.
it is important only high impact bits and sockets are used with this tool, otherwise serious injury could be
ONLY,
not repeat above action until it does.
end of the handle with a hammer, the screw should move, if
screw is to be turned, firmly strike the
BIT HOLDER
slight pressure in the direction the
turned, hold firmly in place applying
Set the bit in screw head to be
Turn clockwise.
the drive using a ½ spanner.
square drive, whilst holding the handle, rotate
adjustment as follows, remove bit holder to reveal the ½
If it is found hard to do this by hand, it is possible to carry out this
L
R/H or loosen L/H, turn the bit holder until it clicks into position.
arrow, L to loosen right hand threads or tighten left hand threads, and R to tighten
other depress and turn the bit holder in the direction of
keep your proper footing and balance at all times - dont overreach. For best footing,
concentrate on the job in hand, no matter how trivial it may seem. Be aware that
maintain tool in top condition. Keep tools clean for the best and safest performance.
keep children away. All visitors should be kept a safe distance from the work area.
ensure that adequate lighting is available. A minimum intensity of 300 lux should be
keep work area clean. Cluttered areas and benches invite accidents.
wear safety goggles, manufactured to the latest European Safety Standards. Everyday
check for damage. Before using the tool, any damaged part should be checked to
learn the tools applications, limitations and the specific potential hazards peculiar to
The tool can be used to loosen and tighten hexagon head bolts etc, using high impact sockets
When finished, remove the bit and store tool and bit in carry case for reuse later.
R
To do this, hold the tool in one hand, grip the bit holder with the
Adjust the tool for either loosening or tightening as required.
Select bit to be used,and insert into bit holder.
USING THE TOOL
wear rubber soled footwear. Keep floor clear of oil, scrap wood etc.
9.
ALWAYS
accidents are caused by carelessness due to familiarity.
8.
ALWAYS
7.
ALWAYS
6.
ALWA YS
provided. Ensure that lighting is placed so that you will not be working in your own shadow.
5.
ALWAYS
4.
ALWAYS
eyeglasses do not have impact resistant lenses, they are not safety glasses.
3.
ALWAYS
ensure that it will operate properly, and perform its intended function.
2.
ALWA YS
it.Read and become familiar with the entire operating instructions.
1.
ALWAYS
to the operator or damage to property, may result.
However, if normal safety precautions are overlooked or ignored, personal injury
Exercising respect and caution will considerably lessen the risk of personal injury.
As with all tools, there are certain hazards involved with their operation and use.
WARNING:
Loading...