Page 1
4” POLISHING KIT
MODEL NO: CBK100C
PART NO: 3052005
OPERATION & MAINTENANCE
INSTRUCTIONS
ORIGINAL INSTRUCTIONS LS0320 - ISS 1
Page 2
INTRODUCTION
Thank you for purchasing this CLARKE Polishing Kit.
Before use, read this manual thoroughly and follow all instructions given.
The polishing kit it is designed to polish steel, brass, copper, nickel, chrome or
silver objects.
ELECTRIC DRILL REQUIRED SPECIFICATIONS
1. The maximum speed of the electric drill must not exceed 3500 rpm.
2. The minimum chuck size of the electric drill must be at least 10 mm.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of
12 months from the date of purchase. Please keep your receipt as proof of
purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
2
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 3
PPE REQUIRED
During use, you must wear the following PPE.
Wear eye protection Wear a mask
Wear protective
gloves
REPLACEMENT POLISHING COMPOUND
Replacement polishing compound is available from your local CLARKE dealer.
3
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 4
WARNINGS
1. Do not use to polish dangerous items like knifes,
2. Ensure adequate ventilation during use.
3. Always wear protective clothing which includes safety goggles, dust mask
and gloves when working with this kit,
4. Make sure that your work surface has been properly assessed for any
potential hazards before starting work.
FIRST AID MEASURES (POLISHING COMPOUND)
After inhalation Supply fresh air, consult doctor in case of complaints
After skin contact Wash with soap and water and rinse thoroughly
After eye contact Rinse the opened eye for several minutes under running
water. If symptoms persist, consult a doctor.
After swallowing Rinse out mouth and drink plenty of water. If symptoms
persist, consult a doctor.
4
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 5
WHAT IS SUPPLIED
The polishing kit is supplied with
•1 tapered shaft
• 1 stick of polishing compound
• 1 polishing wheel
• 1 buffing wheel
SETUP
FITTING THE POLISHING WHEEL TO THE ELECTRIC DRILL
1. Fit the tapered shaft into the drill chuck.
2. Whilst holding the drill chuck with
one hand, screw the polishing
wheel onto the tapered shaft until
it is secure.
BUFFING WHEEL.
The buffing wheel is fitted in the same
way as above.
ADDING COMPOUND TO THE POLISHING WHEEL
1. Squeeze the trigger on the drill.
2. When the wheel has reached
maximum speed, apply the
polishing compound to the wheel
gently as shown.
3. Turn off the drill and allow it to
come to a stop.
4. The polishing wheel is now ready
for use.
5
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 6
USING THE POLISHING KIT
1. Secure your workpiece to prevent it from moving.
2. Squeeze the trigger on the drill.
3. When the wheel has reached maximum speed, apply the wheel to the
item you want to polish gently.
4. Remove the polishing wheel and replace it with the buffing wheel.
5. Repeat step 2 to buff the item to a fine finish.
6
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 7
OTHER BUFFERS IN THE CLARKE RANGE
CBB150 250W 6'' Bench Buffer / Polisher
Part Number: 6500485
The Clarke CBB150 is ideal for buffing and
polishing metal and composite surfaces.
This unit features a robust cast iron base with
rubber feet which reduces vibration, and this
model can also be bolted to a work bench to
make it even easier to use.
Completing this handy machine is a reliable
build and 2x polishing mops included (1x
stitched 1x open style) to get started.
CHDB500 6” Heavy Duty Bench Buffer /
Polisher
Part Number: 6500492
The heavy duty CHDB500 is ideal for buffing
and polishing metal and composite surfaces
to a bright lustred finish.
This unit features a robust cast iron base with
rubber feet which reduces vibration, and this
model can also be bolted to a work bench to
make it even easier to use.
With its built-in motor delivering 500W of
power combined with its bearing balanced
precision machined shafts, this buffer offers
excellent performance.
For added safety, a front mounted on/off
switch makes the polisher easy to switch off,
and easy fitting and removal of polishing
mops makes for efficient working.
Completing this handy machine is a reliable
build, with 1x stitched and 1x open style
polishing mops included to get you started.
7
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Page 8
Loading...