Clarion UDR12 Installation Manual
284-9075-00
;
;
;
;;
;
;;
;
;;
;
;
;
;;
;
6. CONNECTING the Sensor leads
TM
USB navigation unit UDR12
Installation manual
W ARNING
This product must be installed and used only in accordance with these instructions. Any alteration of this product that enables it to be used in ways
other than those provided for in this manual could distract the driver and result in an accident for which the installer may be held liable. CLARION DIS-
CLAIMS ANY LIABILITY THAT MAY RESULT FROM A FAILURE TO INSTALL AS
INDICA TED IN THESE INSTRUCTIONS.
1. BEFORE STARTING
1. The Clarion Auto PC USB Navigation unit UDR12
is designed for use in cars with a negative
ground 12 V power supply.
2. Read these instructions carefully.
3. Be sure to disconnect the battery “
before starting. This is done to prevent short circuits during installation. (Figure 1)
” terminal
Car battery
Figure 1
To install the Speed Signal Cable:
1. Insert the Speed Signal cable securely into
the 3-pin sensor connector at the rear of
the USB Navigation unit.
2. Connect the opposite end of the Vehicle
Speed Signal line to the engine control
computer (or VSS) of your auto. (∗1)
CAUTION
Incorrectly connecting the Speed Sensor connection leads and the Vehicle
Speed Signal line can cause unpredictable results resulting in injury or
accident. Before connecting the speed
signal cables, check the vehicle engine
control computer (EC) position and
Vehicle Speed Signal line with the store
of purchase or the vehicle dealer-shop.
Electro-tap usage
3. Connect the end of the ACC line (∗2) to a
power source that can be turned on and
off by the ignition switch (Accessory power
supply: ACC).
4. Connect the end of the Reverse Gear
Signal (∗3) to the
reverse gear lamp power). The
terminal (for the
terminal
is only fed when the transmission is put in
reverse.
CAUTION
MAKE THE PROPER CONNECTIONS.
Failure to make the correct connections
can cause fire, damage or unpredictable results resulting in injury . or accidents.
Engine control computer (EC）
Electro-tap
2. P ACKAGE CONTENTS
1
USB Navigation unit
2
GPS antenna
3
Installation manual
4
Warranty card
Inter-connection cable (USB cable and Sensor leads) .....2
5
Velcrotape ........................................................................ 2
6
Adhesive tape
7
8
Electro-tap
3. SPECIFICATIONS
GPS tuner unit
Power source voltage: 14.0 V DC
Ground: Negative
Current consumption: 300 mA
Dimensions: 5.91” (150 mm) Width ×
1.42” (36mm) Height ×
5.12” (130mm) Depth
Weight: 1.1lb. (500g)
GPS antenna
Type: Microstrip plane antenna
Dimensions: 1.34” (34 mm) Width ×
Weight: 0.23lb. (105g)
4. CAUTIONS ON INSTALLATION
1. Prepare all articles necessary for installation of the USB Navigation unit.
2. If you have to do any work on the car body ,
such as drilling holes, consult your car
dealer in advance.
3. To increase the strength of the adhesive
tape or velcro, wipe any dust, oil, etc. off
the installation area.
5.
INSTALLING THE GPS ANTENNA AND THE USB CABLE
To install the GPS antenna and the USB
cable
1. Wipe clean the bottom surface of the GPS
antenna (where the adhesive tape will be
installed).
2. Paste the adhesive tape onto the bottom
surface of the GPS antenna.
3. There are two different types of USB
connectors (In & out). Each cables is
uniquely color-coded. Please match the
colors and make certain that the proper
connections are made. (∗4)
Connect the cables to GPS navigation unit
and Auto PC source unit.
4. Improper installation may create errors
in vehicle positioning or cause
unpredictable results.
4. Wipe clean the installation location on the
dash-board where the GPS antenna is to
be attached.
5. Paste the GPS antenna onto the dashboard.
Notes:
1. Install the GPS antenna on the dashboard
in a location where the GPS signals will
reach adequately. (Materials other than
glass cut off the signals.)
2. Do not install the GPS antenna too close
to any air conditioner outlet, defogger, etc.
GPS antenna
0.52”(13.2 mm) Height ×
1.50” (38 mm) Depth
Vehicle speed signal line from EC
Speed sensor connection lead (∗1. Green/White)
7. INSTALLING THE USB navigation unit
To install the USB Navigation unit:
1. Wipe clean the bottom surface of the USB navigation unit (where the velcro will be installed).
2. Paste the velcro onto the bottom surface of the USB navigation unit.
3. Paste the USB navigation unit onto the floor carpet under the seat.
WARNING
USB navigation unit
The USB Unit must be installed flat. Do
not install unit on any side.
CAUTION
When you install this unit into your
vehicle using screws, use M4 × 8
mm screws. Using other screws
can cause damage to the unit.
Velcro tape
8. WIRE CONNECTIONS
Rear view of USB Navigation unit
GPS antenna
After the connection, secure the lead
with a clamp or insulation.
Wire the connection leads and other
cords in such a way that they will not
hinder driving.
8-pin USB jack
1-pin GPS jack
CAUTION
3-pin sensor jack
(Black)
USB cable
to USB Out terminal (∗4)
at the rear of AutoPC source unit
Sensor leads
(Green/White)
(Light Green)
(Red)
(Gray)
to Speed signal
(∗1)
to Reverse gear
signal (∗3)
to ACC
(∗2)
Note:
1. Insert the cables and GPS antenna
securely until they lock.
2. If you are installing both a USB Navigation
unit and a USB CD changer, a USB hub
is required.
Auto PC Source unit
9. GENERAL CAUTIONS
1. Do not open the case. There are no user
M
U
T
E
L
O
V
K
C
A
B
USB cable
serviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized CLARION
service center.
USB navigation unit
Clarion Co., Ltd.
All Rights Reserved. Copyright c 2000: Clarion Co., Ltd.
Printed in Japan 2000/12 (T·K) 284-9075-00
2. Use a soft, dry cloth to clean the case.
Never use a rough cloth, thinner, benzine,
or alcohol, etc. For tough dirt, apply a little
cold or warm water to a soft cloth and wipe
off the dirt gently.
Loading...