Clarion S660 User Manual

MMooddeell SS666600

➤

OOwwnneerr’’ss GGuuiiddee

lliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyy

This Ungo Pro Security system is warranted against defects in material and workmanship. The main unit is covered by this limited lifetime warranty. This Limited Lifetime Warranty applies to Ungo Pro Security systems that have been installed by an authorized Ungo Pro Security dealer. This warranty is to the Original Purchaser ("Owner") and to the original vehicle in which it was installed into. This warranty is not transferable to any subsequent owner(s) of the product(s).

WWaarrrraannttyy PPrrooggrraamm::

Main Unit Limited Lifetime Remote Controls One year from date of purchase Siren One year from date of purchase Shock Sensor One year from date of purchase LED One year from date of purchase Override Switch One year from date of purchase

The Warranty does not cover batteries or products deemed damaged through alterations or installation. It also does not cover products mishandled, misused, neglected, abused, water damaged, or with removed/altered serial numbers.

PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE OF THIS PRODUCT.

This warranty does not cover the costs incurred for removal or reinstallation of the main unit and/or any damage to the vehicle or the vehicle's electrical system.

The sole responsibility of Clarion Corporation of America ("Clarion") under this Warranty shall be limited to the repair or replacement of the product, at the sole discretion of Clarion.

If it becomes necessary to send the product or any defective part to Clarion, the product must be shipped in its original carton or equivalent carton, fully insured, with shipping charges prepaid. Clarion will not assume any responsibility for any loss or damage incurred in shipping.

ALL IMPLIED WARRANTIES EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW SHALL HAVE NO GREATER DURATION THAN THE WARRANTY PERIOD SET FORTH ABOVE. UNDER NO CIRCUMSTANCES SHALL CLARION CORPORATION BE LIABLE FOR ANY LOSS OR DAMAGE, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OR INABILITY TO USE OF THE PRODUCT. BECAUSE SOME STATES DO NOT ALLOW LIMI-

TATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSIONS OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE THE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

Should you have any difficulties with the performance of this product during warranty, please call: 1-800-GO-CLARION or visit your local Ungo Pro Security dealer. You may also contact the National Service Manager at the following address below for additional service help you may need.

Clarion Corporation of America Attn: National Service Manager 661 W. Redondo Beach Blvd. Gardena, Ca 90247

ttaabbllee ooff ccoonntteennttss

lliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyy.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. ii

rreemmoottee ccoonnffiigguurraattiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 33

LCD 2-way configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

standard 4-button configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

wwhhaatt iiss iinncclluuddeedd .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 66

iimmppoorrttaanntt iinnffoorrmmaattiioonn .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 66

system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

rreemmoottee ffuunncctti

ioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 99

LCD 2-way remote standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Standard LCD 2-way icon configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4-button remote standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

LLCCDD 22--wwaayy rreemmoottee ooppeerraattiioonn .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. 1177

system signal paging features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

uussiinngg yyoouurr ssyysstteemm .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1199

warning! safety first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

active arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

passive arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

warn away

response description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

triggered response description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

multi-level security arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

arming while driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

disarming while driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

high security disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

disarming without a remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

silent mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

valet

mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

temperature check mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

nuisance prevention circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

ddiiaaggnnoossttiiccss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. 3300

arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

system status chirps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

interpreting zone diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

ccooddee hhooppppiinngg .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3344

hhiigghh ffrreeqquueennccyy .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3355

oowwnneerr rreeccooggnniittiioonn .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3355

rraappiidd rreessuummee llooggiicc .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3366

ppoowwe

err ssaavveerr mmooddee .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3366

pprrooggrraammmmiinngg ooppttiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3377

sseeccuurriittyy && ccoonnvveenniieennccee eexxppaannssiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3399

gglloossssaarryy ooff tteerrmmss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 4411

rreemmoottee ccoonnffiigguurraattiioonnss

LCD 2-way configuration

➜

1234

1 Vehicle Interior Temperature Indicator 2 Numeric Display 3 AM/PM Indicator 4 Alarm Clock Mode Indicator 5 Timer Function Indicator 6 Transmit Range Indicator 7 Transmission Indication 8 Vibrate/Beep Mode Indicator 9 Power Saver Mode Indicator 10 Remote Start Timer Mode Indicator 11 No Function 12 Vehicle Page Mode Indicator 13 Full Trigger Shock Sensor Indicator 14 Hood/Trunk Open or Trigger Indicator 15 Parking Light Indicator 16 Door Open or Trigger Indicator 17 Arm/Lock Button 18 Disarm/Unlock Button 19 Remote Start Indicator 20 Hood/Trunk Open or Trigger Indicator 21 Remote Start Button 22 Valet®Mode Indicator 23 Remote Start Safety Shutdown Indicator 24 Battery Level Indicator 25 Auxiliary Button 26 Temperature-Controlled Remote Start Indicator 27 Silent Arm/Disarm Mode Indicator 28 Full Trigger Alert Indicator 29 Arm/Disarm Indicator 30 Function Button 31 Celsius/Fahrenheit Indicator

standard 4-button configuration

controls the

AArrmm

and

PPaanniicc

On/Off function.

controls the

DDiissaarrmm

and

PPaanniicc

Off function.

controls

SSiilleenntt MMooddee™™

and

AAuuxxiilliiaarryy

channel 22output.

no function.

and pressed together control channel 44output.

and pressed together control channel 55output

➜

wwhhaatt iiss iinncclluuddeedd

➤ Control module

➤ ASK transceiver/antenna

➤ One 4-button remote

➤ One 2-way LCD remote

➤ Stinger™ DoubleGuard

2-stage shock sensor

➤ Revenger™ Soft Chirp™ 6-tone programmable siren

➤ Status LED indicator light

➤ Push-button Valet

switch

iimmppoorrttaanntt iinnffoorrmmaattiioonn

Congratulations on the purchase of your remote alarm system.

Due to the complexity of this system, it must be installed by an

authorized dealer only. Installation of this product by anyone

other than an authorized dealer voids the warranty. All dealers

are provided with a preprinted dealer certificate to verify autho-

rization.

By carefully reading this Owner's Guide prior to using your

system, you will maximize the use of this system and its features.

You can print additional or replacement copies of this manual by

accessing our web site at www.clarion.com.

system maintenance

The system requires no specific maintenance other than battery

replacement for the remotes.

LCD 2-Way Remote Battery Replacement

The 2-way remote is powered by a 1.5V AAA battery. The

Battery Level indicator has three level indicators that serve as a

visual indication of battery charge. When the battery reaches a

low charge level that requires replacement, the transceiver will

generate a single notification chirp, and the Battery Level indi-

cator will flash continuously.

To replace the battery, gently pull the battery cover release tab, then

slide the door down to expose the battery and remove the expired

battery. Place the new battery into the transceiver observing the

correct polarity. When power is returned the transceiver will light

all icons in the LCD and generate all beeper tones once.

4-Button Remote Battery Replacement

Your remote is powered by a small, lightweight 3-volt lithium

battery (CR2032) that will last approximately one year under

normal use. When the battery begins to weaken, operating range

will be reduced and the LED on the remote will dim.

➜

fcc/id notice

This device complies with Part 15 of FCC rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesirable operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate this device.

➜

Directed Electronics, Inc. 544 Series

Tested to Comply with FCC Standards

Directed Electronics, Inc. 477T Series

Tested to Comply with FCC Standards

Directed Electronics, Inc. 474V/P/S Series

Tested to Comply with FCC Standards

rreemmoottee ffuunnccttiioonnss

The remote buttons are used to send commands to the system.

The descriptions below reflect the standard configuration for this

system. The buttons can be custom configured for the user’s

specific needs by the installer.

LCD 2-way remote standard configuration

LCD 2-way button configuration

Button

The System Arm/Lock and Multi-Level Security Arming func-

tions are controlled by pressing this button.

Button

The System Disarm/Unlock and High Security Disarm functions

are controlled by pressing this button.

Button

Channel 2 output is controlled by pressing and holding this

button for two seconds.

Button

The panic feature is controlled by pressing and holding this

button for three seconds. Press again to disable panic mode.

Button

The LCD backlighting will turn on when pressed for less than one

second; when held for more than five seconds the transceiver will

enter adjustment mode allowing the setting of the clock, timer

mode, and audible melody selection. For more information, please

refer to the

Function Button Configurations

section of this guide.

➜

Button

When pressed and held this button activates the second unlock

or other accessory.

and Buttons

The numeric display toggles between the time of the day and the

alarm clock when these buttons are pressed simultaneously.

and Buttons

Press these buttons simultaneously to activate the parking timer.

Each additional press will toggle through the available options

(10 min., 20 min., 30 min., 1 hour, 1.5 hours, 2 hours, and off).

and Buttons

When pressed simultaneously these buttons toggle between beep

notification and vibrate notification.

and Buttons

When pressed simultaneously these buttons activate battery saver

mode, which will drop power consumption on the transceiver

battery to zero when the alarm is inactive or disarmed.

Standard LCD 2-way icon configuration

Icon

The numeric display icon will show the hours and minutes.

Icon

The AM/PM icon indicates the time before or after noon.

Icon

The alarm clock mode icon indicates that the alarm clock mode

is active.

Icon

The timer function icon flashes during timed functions including

parking timer.

Icon

The transmit range indicator icon stays visible as long as the

system is within operating range.

➜

Icon

The remote transmission indicator icon displays when the trans-

ceiver is transmitting a signal.

Icon

The vibrate/beep mode icon appears when the transceiver is set

to vibrate mode.

Icon

The power saver mode can be turned on or off with the trans-

ceiver. This icon displays the status.

Icon

No function.

Icon

The vehicle page mode icon displays when the alarm module is

paging the transceiver.

Icon

The full trigger shock sensor icon indicates that the shock sensor

has been triggered by a hard shock.

and Icons

The hood/trunk open or trigger icon illuminates when the hood

or trunk trigger has been activated or the hood or trunk is open,

and bypasses those zones until it is closed.

Icon

The parking light icon will flash twice when armed or disarmed.

The icon also flashes during WarnAway and at the beginning and

end of remote start cycles.

Icon

The door open or trigger icon illuminates when the door trigger

has been activated or the door is open, and bypasses that zone

until it is closed.

Icon

No function.

Icon

The Valet®mode icon appears when the system is in Valet®mode.

Icon

The remote start safety shut down icon indicates the vehicle may be

in gear or other unsafe condition inhibiting remote start operation.

Icon

The battery level icon indicates the level of power remaining in

the battery.

Icon

The silent arm/disarm icon appears when the system has been

armed or disarmed in the silent mode.

Icon

The full trigger alert icon illuminates when the security system

has been triggered by a heavy impact, door trigger violation,

optional sensor violation, or a hood/trunk trigger.

Icon

The arm icon appears when the vehicle is armed and locked. The

disarm icon appears when the vehicle is disarmed and unlocked.

Standard LCD 2-way button functions

AAuuddiibbllee

FFuunnccttiioonn BBuuttttoonn IIccoonn IInnddiiccaattiioonn

Lamp On (10 sec)

Power-Saver Mode*

Melody

Beep/Vibrate Mode

4 Vibrations/

1 Beep

Time Adjust for 5 Seconds 2 Beeps Mode (hour)**

Time Adjust 1 Time*** Mode (min)**

Alarm Clock 2 Times*** Set Mode (hour)**

Alarm Clock 3 Times***

Set Mode (min)**

Alarm Clock Music 4 Times*** 5 Selections or Power on Music 1/2/3/4/5 Selection**

Alarm Clock Adjust 5 Times*** Mode (on/off)**

Timer Count Down 6 Times*** Adjust Mode (hour)**

Timer Count Down 7 Times*** Adjust Mode (min)**

Timer Count 8 Times*** 5 Selections Down Ending Melody 1/2/3/4/5 Selection 1**

RS Timer Count 9 Times*** Down Mode (on/off)*

Remote Start On 10 times*** 5 Selections Melody Selection 2 1/2/3/4/5

10 Min Parking

1 Time Melody

Count Down Mode

20 Min Parking

2 Times Melody

Count Down Mode

30 Min Parking

3 Times Melody

Count Down Mode

60 Min Parking

4 Times Melody

Count Down Mode

90 Min Parking

5 Times Melody

Count Down Mode

120 Min Parking

6 Times Melody

Count Down Mode

Parking Count Down

7 Times Melody

Off Mode

Alarm Clock Mode

Melody

On/Off****

Celsius/Fahrenheit

+ +

Melody

Select Mode

* This function will operate in the disarmed state only.

** The button will advance the selection upward. The button will advance the selection downward or select the off setting.

*** Be sure to hold down for five seconds prior to entering timer clock adjust mode operation.

**** Press once to have the alarm clock on. Press twice to have the

alarm clock off.

The remote will revert to normal operation from the set mode when 15-seconds has elapsed without a button entry.

4-button remote standard configuration

Button

The arming is controlled by pressing this button. The panic

alarm is triggered by pressing and holding this button. Press this

button again to cancel the panic alarm.

Button

The disarming function is controlled by pressing this button.

Button

Silent Mode™ and an optional auxiliary function are controlled

by this button. (Silent Mode works by pressing this button for

less than one second before arming or disarming. An optional

auxiliary function, such as trunk release, can be controlled by

pressing and holding this button for 1.5 seconds.)

The auxiliary output controls __________________________.

➜

and Buttons

An optional auxiliary convenience or expansion function that

you have added to your system can be activated by pressing these

buttons simultaneously.

The auxiliary output controls __________________________.

and Buttons

An optional auxiliary convenience or expansion function that

you have added to your system can be activated by pressing these

buttons simultaneously.

The auxiliary output controls __________________________.

and Buttons

No function.

LLCCDD 22--wwaayy rreemmoottee ooppeerraattiioonn

The remote start system operates at 434 MHz and incorporates

Directed’s proprietary A.S.K. out-board two-way transceiver. The

high frequency combined with Binary Data communication

achieves superior range with two-way communication.

system signal paging features

A page is the signal the control module sends to the transceiver as

confirmation of receipt of a command or alarm system status.

When the transceiver receives a page it will generate a page notifi-

➜

cation to the user (notifications are audible beeps or the remote

vibrates) and the LCD icons will display the current system status.

Command Page

When a command (arm/disarm, remote start, or auxiliary

channel) from the transceiver is sent and received, the system will

send a command page back to confirm receipt.

Page Recognition Mode

The transceiver will leave a zone icon illuminated when it has

received a triggered response and will wait for violation recogni-

tion. Press any button on the transceiver, the LCD information

and alarm page alerts will be cleared.

note: The transceiver buttons will not send a command to the system until the alarm page is cleared.

uussiinngg yyoouurr ssyysstteemm

warning! safety first

The following safety warnings must be observed at all times:

➤ Due to the complexity of this system, installation of this

product must only be performed by an authorized Ungo

dealer.

active arming

You can arm the system by pressing of your remote for one

second. When the system arms, you will hear a short siren sound,

or chirp, and see the parking lights flash once. If the power door

locks are controlled by the system, the doors will also lock. While

the system is armed, the status LED will flash approximately once

per second, indicating that the system is actively protecting your

vehicle. If you hear a second chirp after arming and note that the

status LED is flashing in groups, see the Diagnostics Section of

this guide. This extra chirp is called Bypass Notification, which

indicates that a security sensor or switch has been bypassed and

the system is not monitoring that area (zone) of the vehicle.

passive arming

The system can be programmed to arm itself automatically (called

passive arming). If the system is programmed for passive arming, it

will automatically arm 30 seconds after the ignition is turned off

and the system detects that you have left the vehicle by opening and

closing a door. Whenever the system is in its 30-second passive

➜

arming countdown, the status LED will flash twice as fast as it does

when the system is armed. At the 20-second point of the count-

down, the siren will chirp to indicate that the system is about to

arm. At the 30-second point, the parking lights will flash to indicate

that the system is armed.

When armed your vehicle is protected as follows:

➤ Light impacts trigger the Warn Away

signal. When triggered,

the siren chirps and the parking lights flash for a few seconds.

➤ Heavy impacts trip a Triggered Sequence. The sequence

consists of the siren sounding continuously and the parking

lights flashing for a pre-programmed period, which can range

in duration from 1 to 180 seconds.

➤ If a door is opened, the system will immediately start

chirping the siren and flashing the parking lights. Three

seconds later, the siren output changes to a continuous blast.

This progressive response gives you time to disarm the system

with your remote if you inadvertently open the door while

the system is armed, while still providing instant response

(even if the door is immediately closed).

➤ Turning on the ignition key will trip the same progressive re-

sponse as opening a door.

note: If any protected entry point (such as a door or a switch-protected trunk or hood) is open, the system will not passively arm (unless forced passive arming is programmed on. See Programming Options section.) Additionally, each time a sensor is triggered during the arming countdown, the 30-second countdown starts over.

➤ The optional starter kill prevents the vehicle’s starter from

cranking.

warn away®response description

A Warn Away®Response consists of an alarm page along with the

responses described below.

➤

SShhoocckk SSeennssoorr

- Light impacts to the vehicle will flash the

vehicle lights and chirp the siren for a few seconds.

➤

RReemmoottee CCoonnttrrooll NNoottiiffiiccaattiioonn

- Ten quick beeps (or one

vibration).

➤

RReemmoottee CCoonnttrrooll LLCCDD

- The full trigger alert icon (28) will

dimly illuminate for two seconds

➤ The transceiver will enter Page Recognition Mode and

operate alarm page alerts.

triggered response description

A Triggered Response can be activated by any of the triggers listed

below and consists of an alarm page along with the response

described for each trigger. The default Triggered Response dura-

tion is 30 seconds but can be programmed from 1-180 seconds

by your installer with the ProSecurity Programmer.

➤

SSeennssoorr TTrriiggggeerr

- Heavy impacts to the vehicle will instantly

sound the siren and flash the lights for the programmed

duration and report Zone 2.

➜

note: Icons 13 and 14 represent alarm system zone inputs. For more information about icons and the zones they represent refer to the

Standard Remote

Configurations

section.

➜

➤

DDoooorr TTrriiggggeerr

- If a door is opened the siren will chirp for three

seconds, then the siren will sound and the lights will flash for

the programmed duration and report Zone 3. The three

seconds allow the user time to disarm the system with a

minimum of noise should a door be opened inadvertently

while the system is armed.

➤

HHoooodd TTrriiggggeerr

- Opening the hood will sound the siren, flash

the lights for the programmed duration, and report Zone 1.

➤

TTrruunnkk TTrriiggggeerr

- Opening the trunk (if connected) will

instantly sound the siren and flash the lights for the

programmed duration and report Zone 4.

➤

IIggnniittiioonn TTrriiggggeerr

- If the ignition is turned on the siren will

chirp for three seconds, then the siren will sound and the lights

will flash for the programmed duration and report Zone 5.

When a Triggered Response is activated the transceiver will:

➤ Repeat four quick beeps (or vibrate) for 15 seconds.

➤ The full trigger alert icon (28) will turn on for 15 seconds.

➤ The zone icons will turn on and remain on until a transceiver

button is pressed, clearing the page alert.

➤ The transceiver will enter page recognition mode and

generate alarm page alerts.

note: Icons 13, 14, 16, and 20 represent alarm system triggered sequence zone inputs. For more information about icons and the zones they represent refer to the

Standard Remote Configurations

section.

multi-level security arming

Multi-Level Security Arming allows you to select which of the

system's inputs or sensors will be active and which will be

bypassed when the system is armed. (See

Table of Zones

section

of this guide.) Pressing (only in Standard Configuration)

again within five seconds of arming the system will activate the

Multi-Level Security feature. Each time is pressed again, a

different security level is selected. The different security levels are

selected as follows:

➤ Press once: The siren chirps once. The system is armed.

➤ Press a second time within five seconds: The siren chirps

twice followed by a long chirp. Zone 2 is now bypassed.

➤ Press a third time within five seconds: The siren chirps

three times followed by a long chirp. Zone 4 is now bypassed.

➤ Press a fourth time within five seconds: The siren chirps

four times followed by a long chirp. Zones 2 and 4 are now

bypassed.

➤ Press a fifth time within five seconds: The siren chirps

five times followed by a long chirp. All input zones, except

the ignition, are now bypassed.

note: Multi-Level Security Arming only applies to a single arming cycle. Once the system is disarmed and then re-armed, all the zones will be active again.

➜

arming while driving

Your security system can be armed while driving the vehicle!

Simply press on the remote for two seconds while the vehicle

is running. The siren will chirp once to indicate that the security

system is armed, and then once more to indicate that the ignition

is on. The system will not respond to any input except the door

triggers, and the starter kill relay (if installed) will not be acti-

vated. Once you have arrived at your destination, the system will

disarm when the ignition is turned off. The siren will chirp twice

and the LED will then stop flashing. The system can also be

disarmed at any time by pressing .

The LCD 2-way remote will beep once (or vibrate), and the arm icon

(29) will be displayed on the LCD.

disarming

To disarm the security system, press . You will hear two

chirps, and the parking lights will flash twice. If the power locks

are controlled by the system, the doors will also unlock. The siren

chirping either four or five times when disarming indicates

Tamper Alert, which is described in the Diagnostics Section of

this guide.

➜

note: If the transceiver received a Warn Away®or triggered response page while armed, the first press of the unlock button will clear the page alert. A second press will turn the siren off, and a third press will disarm the system.

➜

disarming while driving

Press on the remote or simply turn off the ignition to disarm

the system. The lights will flash twice, the doors will unlock, the

siren will chirp twice, and the status LED will turn off. The 2-

way remote will beep twice (or vibrate). The disarm icon (29) will

be displayed on the LCD.

high security disarm

This security system offers High Security Disarm. High Security

Disarm is a feature that makes it possible to silence and reset the

system while it is triggering, without disarming the system. If the

system is triggered and the siren has been sounding for longer

than six seconds, pressing on the remote will stop the trigger

and return the unit to the armed state. The system will not

disarm, but rather reset. This prevents you from disabling the

system should you wish to disarm it without visually checking the

vehicle. Pressing after resetting the system will disarm the

system; pressing this button during the first six seconds of the

triggered sequence will disarm the security system immediately.

The six second timer is provided for your convenience, in case the

system is accidentally triggered.

➜

disarming without a remote

If your remote is lost or damaged, you can manually disarm your

vehicle security system. To disarm the system without a remote,

you must have the vehicle's ignition key and know where the

Valet

button is located. Be sure to check with your installer at

the time of installation for both the location and the preset

response (1-5 presses) of the Valet

button.

To disarm the security system,

turn the ignition to the ON posi-

tion. Press the Valet

button the

preset number of times (one to

five times) within 15 seconds.

After five seconds, the system will

disarm. If the system does not

disarm, you may have waited too

long; turn the ignition off and on

and try again.

Location of Valet®Button_________________________________

Number of Presses_____________________________________

important! The Valet®button can be programmed to respond to 1-5 presses for the disarm function. You must check with the installer to verify the programming for your individual unit.

➜

DRW-35

silent mode

To temporarily turn off the arm or disarm chirps, use Silent

Mode™. Simply press for less than one second before

arming or disarming, and the confirmation chirp(s) will be elim-

inated for that one operation only. If you want the arm/disarm

chirps turned off permanently, your dealer can do this for you.

panic mode

If you are threatened in or near your vehicle, you can attract

attention by triggering the system with your remote. Just press

for two seconds, and you will enter Panic Mode. The siren

will sound and the parking lights will flash for the programmed

siren duration. To stop Panic Mode at any time, press on

the remote again.

The LCD 2-way remote will beep (or vibrate) continuously

when the system enters panic mode. The 2-way remote will not

generate a page notification when panic mode is exited.

note: Once panic mode has been entered, the siren will sound for the programmed duration.

➜

note: The Warn Away®response to lighter impacts is bypassed if the system is armed using Silent Mode. This ensures that no chirps will be emitted by the siren in an area you want chirp-free. The system is still fully capable of triggering. Only the Warn Away®response is bypassed.

➜

valet®mode

You can prevent your security system from automatically arming

and triggering by using Valet

Mode. This is very useful when

washing the vehicle or having it serviced. In Valet

Mode, the

security system will not arm, even with the remote, but all

convenience functions (door locks, trunk release, etc.) will

continue to work normally.

To enter or exit Valet®Mode:

1. Turn the ignition on.

2. Turn the ignition off.

3. Press and release the Valet

button within 10 seconds.

The status LED will light solidly if you are entering Valet

Mode, and it will go out if you are exiting Valet®Mode.

To enter or exit Valet®Mode using the remote:

Steps 2 through 3 must be quickly and smoothly completed.

1. Open any vehicle door.

2. Press .

3. Press

4. Press again.

The status LED will light solidly if you are entering Valet

Mode, and it will go out if you are exiting Valet®Mode.

➜

DRW-35

setting the clock

To set the clock press and hold for five seconds, the trans-

ceiver will chirp twice and the hour selection will start flashing.

Immediately press to advance the hour selection to reverse

the hour selection. Once the correct hour is displayed press

again and the minute selection will start flashing. Then

press to advance the minute selection to reverse the

minute selection. Once the correct time is displayed simply

stop pressing any buttons for 15 seconds and the transceiver

will automatically exit the clock mode.

nuisance prevention circuitry

Your system has Directed’s Nuisance Prevention Circuitry

™

(NPC™). It prevents annoying repetitive trigger sequences due to

faulty door pin switches or environmental conditions such as

thunder, jackhammers, airport noise, etc.

➜

Example

If the alarm triggers three times within a 60-minute period and

each time the same sensor or switch triggers the alarm, NPC

™

will interpret those triggers as false alarms. After the third trigger,

NPC

™

ignores, or bypasses, that sensor or switch (along with any

other sensors or switches sharing the same zone) for 60 minutes.

If the bypassed sensor tries to trigger the security system while it

is being bypassed, the 60-minute bypass period will start over.

This ensures that a sensor that is continually being triggered will

remain bypassed.

The vehicle doors are protected by NPC

™

differently. If your

security system is triggered by an open door for three full cycles,

the system will bypass the doors until the trigger ceases.

ddiiaaggnnoossttiiccss

The microprocessor at the heart of your system is constantly

monitoring all of the switches and sensors connected to it. It is

designed to detect any faulty switches and sensors and prevents

note: Arming and disarming the system does not reset this function! The only ways to reset a bypassed zone are for it to not trigger for 60 minutes, or to turn on the ignition. If testing your system, it is important to remember that the NPC

™

programming can cause zones to be bypassed and appear to stop working. If five chirps are heard when disarming, NPC

™

has been engaged. If you

wish to clear the NPC™memory, turn the ignition on.

them from disabling the entire system. The microprocessor will

also record and report any triggers that occurred during your

absence. Refer to the

System Status Chirps

and

Table of Zones

sections of this guide for diagnostic information.

arming diagnostics

If the security system is armed at the same time that an input is

active (such as a door opening or sensor triggering), you will hear

one siren chirp to indicate arming and a second siren chirp to indi-

cate Bypass Notification. A Bypass Notification chirp means that

the security system ignores the input that was active when the

system was armed, until that input ceases. Three seconds after that

input ceases, the security system will resume normal monitoring.

For example, if your vehicle has an interior light exit delay and you

arm your security system before the interior light turns off, you

may hear a second Bypass Notification chirp. Once the light turns

off, however, the security system resumes normal monitoring.

disarming diagnostics

Extra chirps that are heard when disarming the system are the

Tamper Alert. If four chirps are heard when disarming the

system, then the security system was triggered in your absence. If

five chirps are heard when disarming the system, a zone was trig-

gered so many times that the Nuisance Protection Circuitry

™

has

➜

note: Bypass Notification does not occur when the system is in Silent Mode or if the notification chirps have been programmed off by the installer.

➜

bypassed that zone. In either case, the status LED will indicate

which zone was involved (see

Table of Zones

section). The secu-

rity system will retain this information in its memory and chirp

four or five times each time it is disarmed, until the next time

that the ignition is turned on.

system status chirps

The siren will chirp when arming/disarming the system. The

pattern of chirps will audibly report the system’s status as

described below.

Action Number of Chirps Description

Arm 1 System armed

Arm 1 (3-second delay), 1 System armed with

Bypass Notification

Disarm 2 System disarmed

Disarm 4 System disarmed with

Tamper Alert

Disarm 5 System disarmed NPC

active

➜

table of zones

A zone is represented by the number of LED flashes used by the

system to identify a particular type of input. Standard input

assignments are listed in the following table, along with spaces to

write in any optional sensors or switches that have been installed.

ZONE

(Number of DEALER-INSTALLED

LED Flashes) DESCRIPTION OPTIONS

Trunk Pin

Instant trigger - a heavier impact detected by the shock sensor

Door switch trigger

Instant trigger - for optional sensors

Ignition trigger

Hood Pin

interpreting zone diagnostics

Warn Away responses are not reported by arming or disarming

diagnostics. If you receive a Bypass notification when arming or

a Tamper Alert notification when disarming, look at the LED.

Active or triggered zones will be indicated by a pattern of blinks

by the LED.

Example

If zone 3 was active or triggered, the LED will blink three times

with a two-second pause. Then it will blink three times again,

and repeat until the ignition is turned on.

➜

ccooddee hhooppppiinngg

The receiver and remotes use a mathematical formula called an

algorithm to change their code each time the remote is used.

This technology has been developed to increase the security of

the unit. The control unit knows what the next codes should be.

This helps to keep the remote “in sync” with the control unit

even if you use the remote control out of range of the vehicle.

However, if the remote has been pressed many times out of range

of the vehicle, or the battery has been removed, it may fall out of

sync with the control unit and fail to operate the system. To re-

sync the remote simply press several times within range of

the vehicle. The alarm will automatically re-sync and respond to

the remote normally.

note: Your system stores the last two triggered zones in memory. If your system has been triggered but the LED has been reset by turning on the ignition, your dealer can still recall the last two zones that were triggered. Contact your dealer for details.

hhiigghh ffrreeqquueennccyy

Your system transmits and receives at 434 MHz. This provides a

cleaner spectrum with less interference and a more stable signal.

Enjoy a phenomenal increase in range, even in areas with high

radio interference.

oowwnneerr rreeccooggnniittiioonn

Owner Recognition is a revolutionary new feature available only

from Directed. Using a ProSecurity Programmer, hand-held

programming tool, your dealer can program many of the system

settings. The programmer makes it possible to program different

settings for each remote that is used with the system. Then,

whenever a specific remote is used, the system will recall the

settings assigned to that remote. Owner Recognition lets up to

four users of the system have different settings that meet their

specific needs. It is almost like having four separate alarms in

your vehicle, one for each user.

note: Owner Recognition cannot be programmed without a ProSecurity Programmer and the necessary software. Check with your dealer for more information.

rraappiidd rreessuummee llooggiicc

This ProSecurity system will store its current state to non-volatile

memory. If power is lost and then reconnected the system will

recall the stored state from memory. This means if the unit is in

Valet

Mode and the battery is disconnected for any reason, such

as servicing the car, when the battery is reconnected the unit will

still be in Valet

Mode. This applies to all states of the system

including arm, disarm, and Valet

Mode.

ppoowweerr ssaavveerr mmooddee

Your system will automatically enter Power Saver Mode while

armed or in Valet

Mode, after a period of time in which no

operation has been performed. This lowers the current draw on

the vehicle's battery. Power Saver Mode takes over under the

following conditions:

➤ Power Saver when the system is armed: After the system has

been armed for 24 hours the LED will flash at half its

normal rate, decreasing the system's current draw.

➤ Power Saver in Valet

Mode: When the system enters Valet

Mode the LED illuminates steadily. If the vehicle is not used

(ignition is not turned on) for a one hour period while the

system is in Valet

Mode, the LED will shut off. If the

system remains in Valet

Mode, the LED will come back on

the next time the ignition is turned on and then back off.

pprrooggrraammmmiinngg ooppttiioonnss

Programming options control your system's normal, operational

set-up. Most options do not require additional parts, but some

may require installation labor.

The following is a list of the programmable options, with the

factory settings in Bold.

➤

AAccttiivvee

arming (from remote only) or passive arming (auto-

matic arming 30 seconds after the last door has been closed).

➤ Arming/disarming siren chirps

oonn

or off.

➤ The ignition controlled door lock feature

oonn

or off: When this

feature is programmed on, the doors will lock three seconds

after the ignition is turned on, and unlock when the ignition

is turned off. If your installer is programming the security

system with the ProSecurity Programmer, ignition lock and

unlock are independent features that can be programmed

separately.

➤ Passive door locking (with passive arming) or

aaccttiivvee ddoooorr

lloocckkiinngg

(only when arming with the remote). Passive locking

allows the vehicle's doors to lock when the security system

passively arms (after the 30-second countdown). This

feature only works if passive arming has been programmed.

➤ Panic mode

eennaabblleedd

/disabled when the ignition is turned on.

(Some states have laws against sirens sounding in moving

cars.)

➤ Forced passive arming

oonn

or off. If your security system is

programmed for passive arming and the forced passive

arming feature has been programmed on, the system will

passively arm after one hour, even if a protected entry has

been left open. Forced passive arming ensures that the

system will be armed if a door has accidentally been left ajar

when leaving the vehicle.

➤ Full trigger response

3300

or 60 seconds: This determines how

long the full triggered sequence lasts. Some states have laws

regulating how long a security system can sound before it is

considered a nuisance. If your installer is programming the

security system with the ProSecurity Programmer, the full

triggered response can be programmed for any duration

ranging from 1 to 180 seconds.

➤ Automatic Engine Disable (AED) on or

ooffff

. The purpose of

this feature is to protect the vehicle from being stolen at all

times, regardless of whether or not the alarm is armed. If

AED is programmed on, the starter of the vehicle will be

disabled 30 seconds after the ignition is turned off. Once the

key is turned off, the LED will flash slowly (one-half its

normal armed rate) to indicate the AED arming cycle.

Thirty seconds later, the starter will be disabled. To start the

car, it will be necessary to disarm the system with the

remote. It is also possible to disarm the AED feature by

turning the ignition key to the RUN position and pressing

note: When the system passively arms after one hour, the entry point that has been left open, and anything connected to the same zone, is bypassed and cannot trigger the system. However, the remaining inputs to the system are fully operational.

the Valet®button the programmed number of times. AED is

also disabled when the system is in Valet

mode.

➤ Siren tones and chirp volume. The output of the Revenger

™

Soft Chirp™siren consists of six different tones in sequence.

Any of these tones can be eliminated by a dealer, resulting in a

unique, easily identifiable siren sound. The chirps can be either

full volume or

66 ddeecciibbeellss qquuiieetteerr

than the full alarm blast.

sseeccuurriittyy && ccoonnvveenniieennccee eexxppaannssiioonnss

Listed below are some of the many expansion options available.

Please consult your dealer for a complete explanation of all the

options available to you.

Audio Sensor:

Metal on glass, glass cracking, and breaking

glass produce distinctive acoustic signatures. The 506T audio

sensor uses a microphone to pick up sounds, then analyzes them

with proprietary acoustic software to determine if the glass has

been struck.

Backup Battery:

The 520T keeps the system armed, triggers the

alarm and keeps the starter interrupt active if main battery is dis-

connected.

note: This feature will only function if the FailSafe

Starter Kill relay has been installed.

Hood Lock:

Prevents the vehicle’s hood from being opened

without a key, keeping thieves away from the system’s siren, the

battery connections, and other components under the hood.

Field Disturbance Sensor:

An invisible dome of coverage is estab-

lished by installing the 508D “radar” sensor. Your system can

react to any intrusions into this field with the full triggered

sequence.

Power Locks:

This system offers lock outputs that can control

some manufacturers' power door lock systems. For other

systems, additional parts may be required.

Power Trunk Release:

The accessory output of the system can op-

erate a factory power release for the vehicle’s trunk or hatch.

Although the on-board relay can control most power trunk re-

leases, sometimes an optional relay is required. If the factory

release is not power-activated, Directed

's 522T trunk release

solenoid can often be added.

Power Window Control:

Automatic power window control is pro-

vided with the 529T and 530T systems. These can operate

power windows, and can roll them up automatically when the

system is armed, roll them down, or both up and down.

gglloossssaarryy ooff tteerrmmss

Control Unit:

The “brain” of your system. Usually hidden under-

neath the dash area of the vehicle. The control unit houses the

microprocessor which monitors your vehicle and controls all

system functions.

Fault-Proof Starter Interrupt:

An automatic switch controlled by

your system that prevents the vehicle’s starter from cranking

whenever the system is armed. The vehicle is never prevented

from cranking when the system is disarmed, in Valet

mode, or

if the starter interrupt switch itself fails. Your system has feature-

ready circuitry for the starter interrupt, however installation may

require additional labor.

Input:

A physical connection to the system. An input can be

provided by a sensor, pinswitch or by existing systems in the

vehicle, such as ignition or courtesy lights.

LED:

A blue light mounted at a discretionary location inside the

vehicle. It is used to indicate the status of your system.

Shock Sensor:

This system has a dual zone shock sensor. This

sensor is mounted in the vehicle and designed to pick up impacts

to the vehicle or glass.

LCD 2-Way Remote:

A hand-held, transceiver which operates and

monitors the various functions of your system.

Trigger or Triggered Sequence:

This is what happens when the

alarm “goes off” or “trips.” The triggered sequence of your

system consists of the siren sounding and parking lights flashing

for the programmed duration.

Valet®Button:

A small push-button switch mounted at a discre-

tionary location inside the vehicle. It is used to override the

starter interrupt when a remote is lost or damaged, or to enter or

exit Valet

Mode.

Warning Zone Response:

Lighter impacts to the vehicle will

generate the Warning Zone response. It consists of several

seconds of siren chirps and parking light flashes.

Zone:

A zone is a separate input that the alarm can recognize as

unique. Each input to the system is connected to a particular

zone. Often two or more inputs may share the same zone.

QUICK REFERENCE GUIDE

Arming

■ To arm, press . When the system arms, you will hear a short chirp, and the parking lights will flash once.

Arming while driving

■ To arm the system while driving, press on your remote while the vehicle is running. The system will chirp once and then once more to indicate that the ignition is on.

Disarming

■ To disarm, press . You will hear two chirps, and the parking lights will flash twice.

High security disarm

■ For high security disarm, press on your remote and the siren will stop sounding. To completely disarm the security system, press again and the system will chirp 4 or 5 times (reporting the trigger).

Disarming without a remote

■ Turn on the ignition. Press the Valet®button within 15 seconds. The system should now disarm. If it does not, you may have waited too long, so turn the ignition off and on and try again.

Silent Mode

™

■ Pressing briefly before arming or disarming will eliminate the confirma- tion chirp(s) for that one operation only.

Panic Mode

■ Press for 2 seconds, and you will enter Panic Mode. The siren will sound and the parking lights will flash for 30 seconds. To stop Panic Mode at any time, press on the remote again.

Location of Valet®switch_________________________________ Number of Valet

switch pulses for disarming_______________

CCuutt aalloonngg ddootttteedd lliinnee aanndd ffoolldd ffoorr aa qquuiicckk aanndd eeaassyy rreeffeerreennccee ttoo kkeeeepp iinn yyoouurr ppuurrssee oorr wwaalllleett..

✂

Get Started

Get Protected

Ungo Pro Security 661 W. Redondo Beach Blvd. Gardena, Ca. 90247

800-GO-CLARION

Clarion S660 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual