Clarion ProSecurity RS10 Installation Manual

ProSecurity

Model RS10

installation guide

NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.

table of contents

Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™, Nite-Lite®, Nuisance Prevention® Circuitry, Revenger®, Silent Mode™, Soft Chirp®, Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn Away® are all Trademarks or Registered Trademarks of Directed Electronics.

what is included . . . . . . . . . . . . . . . . . . . . . . . 3

warning! safety first . . . . . . . . . . . . . . . . . . . . 4

installation points to remember . . . . . . . . . . . . 5

finding the wires you need. . . . . . . . . . . . . . . . 6

obtaining constant 12V . . . . . . . . . . . . . . . . 6

finding the starter wire . . . . . . . . . . . . . . . . 6

finding the 12V switched ignition wire . . . . . . 7

finding the accessory wire. . . . . . . . . . . . . . . 7

finding a (+) parking light wire . . . . . . . . . . . 8

finding the tachometer wire . . . . . . . . . . . . . 8

finding the wait-to-start bulb wire for diesels . 9

primary harness (H1) wiring diagram . . . . . . . 10

4-pin satellite harness diagram . . . . . . . . . . . 10

heavy gauge relay wiring diagram . . . . . . . . . . 11

door lock harness, 3-pin connector . . . . . . . . . 11

remote engine start harness (H2) wiring diagram 11

primary harness (H1), 9-pin connector . . . . . . 12

heavy gauge relay interface . . . . . . . . . . . . . . 16

remote engine start harness (H2), 5-pin connect-

or . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

neutral safety switch interface . . . . . . . . . . . . 18

general motors trucks, SUVs, and column shifti-

ng passenger cars . . . . . . . . . . . . . . . . . . . 20

pre-1996 dodge dakota pickups with 2.5 liter mot

ors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

bypassing GM anti-theft systems (VATS) . . . . . 21

1995 and newer vehicle anti-theft systems

(immobilizers) . . . . . . . . . . . . . . . . . . . . . . . 22

passlock I and passlock II (PL-1 and PL-2) . . 22 passkey III (PK-3), transponder-based systems22

optional anti-grind relay . . . . . . . . . . . . . . . . 23

programming jumpers . . . . . . . . . . . . . . . . . . 24

light flash (+)/(-) . . . . . . . . . . . . . . . . . . . 24

tach threshold on/off . . . . . . . . . . . . . . . . . 24

plug-in program switch . . . . . . . . . . . . . . . . . 25

transmitter/receiver learn routine. . . . . . . . . . 26

tach learning . . . . . . . . . . . . . . . . . . . . . . . . . 28

operating settings learn routine . . . . . . . . . . . 28

to learn the tach signal . . . . . . . . . . . . . . . 28

features menu . . . . . . . . . . . . . . . . . . . . . . . . 30

feature descriptions. . . . . . . . . . . . . . . . . . . . 31

shutdown diagnostics. . . . . . . . . . . . . . . . . . . 33

rear defogger control . . . . . . . . . . . . . . . . . . . 34

timer mode . . . . . . . . . . . . . . . . . . . . . . . . . . 35

safety check . . . . . . . . . . . . . . . . . . . . . . . . . 35

troubleshooting. . . . . . . . . . . . . . . . . . . . . . . 36

wiring quick reference guide . . . . . . . . . . . . . 39

what is included

■ The control module (see diagram)

■ One SAA474U remote transmitter

■ The plug-in program switch

■ A hood pinswitch

■ A toggle override switch

■ XR+ antenna receiver

6-pin relay output

4-pin satellite/

harness

9-pin main harness

status LED

2-pin BLUE program plug

3-pin/2-wire door lock harness

4-pin/3-wire receiver port

5-pin remote start

harness

warning! safety first

The following safety warnings must be observed at all times:

■ Due to the complexity of this system, installation of this product must only be performed by an authorized

Ungo dealer.

■ When properly installed, this system can start the vehicle via a command signal from the remote control

transmitter. Therefore, never operate the system in an area that does not have adequate ventilation. The fol-

lowing precautions are the sole responsibility of the user; however, authorized Ungo dealers should make the

following recommendations to all users of this system:

1. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).

2. When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote

engine start system must be disabled using the installed toggle switch.

3. It is the user's sole responsibility to properly handle and keep out of reach from children all remote

control transmitters to assure that the system does not unintentionally remote engine start the vehicle.

4. THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT

TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PAR-

TIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED.

■ Use of this product in a manner contrary to its intended mode of operation may result in property damage,

personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1)

Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the

keys in the ignition. The user will be responsible for having the neutral safety feature of the vehicle period-

ically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be

performed by an authorized Ungo dealer in accordance with the Safety Check outlined in this product instal-

lation guide. If the vehicle starts in gear, cease remote engine start operation immediately and consult with

the user to fix the problem immediately.

■ After the remote engine start module has been installed, test the remote engine start module in accordance

with the Safety Check outlined in this installation guide. If the vehicle starts when performing the Neutral

Safety Shutdown Circuit test, the remote engine start unit has not been properly installed. The remote engine

start module must be removed or properly reinstalled so that the vehicle does not start in gear. All installa-

tions must be performed by an authorized Ungo dealer. OPERATION OF THE remote engine start MODULE

IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE

remote engine start SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL

INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED remote

engine start MODULE. UNGO WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTAL-

LATION COSTS.

installation points to remember

IMPORTANT! This product is designed for fuel-injected, automatic transmission vehicles only. Installing it in a standard transmission vehicle is dangerous and is contrary to its intended use.

Before beginning the installation:

■ Please read this entire installation guide before beginning the installation. The installation of this remote

engine start system requires interfacing with many of the vehicle’s systems. Many new vehicles use low-

voltage or multiplexed systems that can be damaged by low resistance testing devices, such as test lights

and logic probes (computer safe test lights). Test all circuits with a high quality digital multi-meter before

making connections.

■ Do not disconnect the battery if the vehicle has an anti-theft-coded radio. If equipped with an air bag, avoid

disconnecting the battery if possible. Many airbag systems will display a diagnostic code through their

warning lights after they lose power. Disconnecting the battery requires this code to be erased, which can

require a trip to the dealer.

■ Remove the dome light fuse. This prevents accidentally draining the battery.

■ Roll down a window to avoid being locked out of the vehicle.

After the installation:

■ Test all functions. The "Using Your System" section of the Owner's Guide is very helpful when testing.

■ Complete the vehicle Safety Check outlined in this manual prior to the vehicle reassembly.

finding the wires you need

IMPORTANT! Do not use a 12V test light or logic probe (computer safe test light) to locate these wires! All testing described in this manual assumes the use of a digital multimeter.

We recommend two possible sources for 12V constant: The (+) terminal of the battery, or the constant 12V supply

to the ignition switch. Always install a fuse within 12 inches of this connection. If the fuse will also be power-

ing other circuits, such as door locks, a power window module, or a Nite-Lite® headlight control system, fuse

accordingly.

IMPORTANT! Do not remove the fuse holder on the red wire. It ensures that the control module has its own fuse, of the proper value, regardless of how many accessories are added to the main power feed.

The starter wire provides 12V directly to the starter or to a relay controlling starter. In some vehicles, it is

necessary to power a cold start circuit. A cold start circuit will test exactly like a starter circuit, but it does not

control the starter. Instead, the cold start circuit is used to prime the fuel injection system for starting when the

vehicle is cold.

How to find the starter wire with your multimeter:

1. Set to DCV or DC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Probe the wire you suspect of being the starter wire. The steering

column is an excellent place to find this wire. Remember you do not

need to interrupt the starter at the same point you test it. Hiding

your starter kill relay and connections is always recommended.

4. Turn the ignition key switch to the start position. Make sure the car

is not in gear! If your meter reads (+)12V, go to the next step. If it doesn’t, probe another wire.

finding the starter wire

obtaining constant 12V

5. Cut the wire you suspect of being the starter wire.

6. Attempt to start the car. If the starter engages, reconnect it and go back to Step 3. If the starter does not

turn over, you have the right wire.

The ignition wire is powered when the key is in the run or start position. This is because the ignition wire powers

the ignition system (spark plugs, coil) as well as the fuel delivery system (fuel pump, fuel injection computer).

Accessory wires lose power when the key is in the start position to make more current available to the starter motor.

How to find (+)12V ignition with your multimeter:

1. Set to DCV or DC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Probe the wire you suspect of being the ignition wire. The steering

column harness or ignition switch harness is an excellent place to find

this wire.

4. Turn the ignition key switch to the run position. If your meter reads

(+)12V, go to the next step. If it does not read (+)12V, probe another wire.

5. Now turn the key to the start position. The meter display should stay

steady, not dropping by more than a few tenths of a volt. If it drops close

to or all the way to zero, go back to Step 3. If it stays steady at (+)12V, you have found an ignition wire.

An accessory wire will show (+)12V when the key is in the accessory and run positions. It will not show (+)12V

during the cranking cycle. There will often be more than one accessory wire in the ignition harness. The correct

accessory wire will power the vehicle's climate control system. Some vehicles may have separate wires for the

blower motor and the air conditioning compressor. In such cases, it will be necessary to add a relay to power the

second accessory wire.

finding the accessory wire

finding the 12V switched ignition wire

Most vehicles use a (+) parking light circuit. The (+) parking light wire is often found near the light switch. In

many vehicles the light switch is built into the turn signal lever; in these vehicles the parking light wire can be

found in the steering column. The same wire can often be accessed in the kick panel or running board.

NOTE: Many Toyotas and other Asian vehicles, send a (-) signal from the switch to a relay. The relay then sends (+)12V to the bulbs. Whenever you have difficulty finding a (+) parking light wire near the switch, simply test the wires at any switch or control panel that is lit by the instrument panel lighting. Remember, you need a (+) parking light wire that does not vary with the dimmer setting.

How to find a (+) parking light flash wire with your multimeter:

1. Set to DCV or DC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Probe the wire you suspect of being the parking light wire. Usually, the area near the headlight/parking light

switch is an excellent area to start, as is the kick panel.

4. Turn on the parking lights. If your meter shows (+)12V, turn off the parking lights and make sure it goes back

to zero.

5. If it does return to zero, turn the parking lights back on and, using the dash light dimmer control, turn the

brightness of the dash lights up and down. If the meter changes more than a volt when using the dimmer,

look for another wire. If it stays relatively close to (+)12V, you have found your parking light wire.

NOTE: Vehicles that use a (-) signal from the switch to the factory relay may be interfaced directly. (See H1/5 WHITE wire of Primary Harness (H1) Wire Connection Guide section.)

To test for a tachometer wire, a multimeter capable of testing AC voltage must be used. The tachometer wire will

show between 1V and 6V AC. In multi-coil ignition systems, the system can learn individual coil wires. Individual

coil wires in a multi-coil ignition system will register lower amounts of AC voltage. Also, if necessary, the system

finding the tachometer wire

finding a (+) parking light wire

can use a fuel injector control wire for engine speed sensing. Common locations for a tachometer wire are the

ignition coil itself, the back of the gauges, engine computers, and automatic transmission computers.

IMPORTANT! Do not test tachometer wires using a test light or logic probe. The vehicle will be damaged.

How to find a tachometer wire with your multimeter:

1. Set to ACV or AC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Start and run the vehicle.

4. Probe the wire you suspect of being the tachometer wire with the red probe of the meter.

5. If this is the correct wire the meter will read between 1V and 6V.

In diesel vehicles it is necessary to interface with the wire that turns on the WAIT-TO-START light in the dash-

board. This wire illuminates the bulb until the vehicle’s glow plugs are properly heated. When the light goes out

the vehicle can be started. This wire is always available at the connector leading to the bulb in the dashboard.

It can also be found at the Engine Control Module (ECM) in many vehicles.

To test and determine the polarity of this wire:

1. Set your multimeter to DCV or DC voltage (12 or 20V is fine).

2. Attach the (+) probe of the meter to (+)12V.

3. Probe the wire that you suspect leads to the bulb with the (-) probe of the meter.

4. Turn the ignition switch to the ON position.

5. If the meter indicates 12 volts until the light goes out you have isolated the correct wire and the wire's polar-

ity is negative (ground while the bulb is on).

6. If the meter reads zero volts until the light goes out and then reads 12 volts, you have isolated the correct

wire and the wire's polarity is positive.

finding the wait-to-start bulb wire for diesels

primary harness (H1) wiring diagram

______

4-pin satellite harness diagram

______

PINK IGNITION TRIGGER

PURPLE STARTER TRIGGER

ORANGE ACCESSORY TRIGGER

BLUE STATUS OUTPUT

WHITE (+/-) LIGHT FLASH

BLACK GROUND

RED/WHITE CHANNEL 2 (VALIDITY ONLY)

WHITE/RED (+) ACTIVATION INPUT

GRAY/BLACK (-) WAIT TO START INPUT

WHITE/BLUE (-) ACTIVATION INPUT

YELLOW (+) IGNITION OUT (TO ALARM)

GREEN/WHITE FACTORY ALARM REARM

LIGHT GREEN/BLACK FACTORY ALARM DISARM

H1/1

H1/2

H1/3

H1/4

H1/5

H1/6

H1/7

H1/8

H1/9

heavy gauge relay wiring diagram

______

door lock harness, 3-pin connector

______

Note: Refer to TechTip 1041 for wiring information.

remote engine start harness (H2) wiring diagram

______

BLUE/WHITE (-) 200 mA 2ND STATUS/REAR DEFOGGER OUTPUT

GRAY (-) HOOD PINSWITCH SHUTDOWN WIRE

BROWN (+) BRAKE SWITCH SHUTDOWN WIRE

VIOLET/WHITE TACHOMETER INPUT WIRE

BLACK/WHITE (-) NEUTRAL SAFETY SWITCH INPUT

H2/1

H2/2

H2/3

H2/4

H2/5

BLUE (-) UNLOCK OUTPUT

EMPTY NOT USED

GREEN (-) LOCK OUTPUT

RED (+) (30A) HIGH CURRENT 12V INPUT

PINK/WHITE (+) PROGRAMMABLE OUTPUT FOR ACCESSORY OR IGNITION

RED (+) (30A) HIGH CURRENT 12V INPUT

ORANGE (+) (30 AMP) OUTPUT TO ACCESSORY CIRCUIT

PURPLE (+) (30 AMP) OUTPUT TO STARTER CIRCUIT

PINK (+) (30 AMP) OUTPUT TO IGNITION CIRCUIT

primary harness (H1), 9-pin connector

This wire sends a negative pulse every time the remote engine start is activated or the doors are unlocked. This

can be used to pulse the disarm wire of the vehicle's factory anti-theft device. Use a relay to send a (-) or (+)

pulse to the disarm wire as shown in the following diagrams.

Relay for Negative (-) Disarm Wire Relay for Positive (+) Disarm Wire

This wire sends a negative pulse every time the remote engine start shuts down or the doors are locked. This can

be used to pulse the arm wire of the vehicle's factory anti-theft device. Use a relay to send a (-) or (+) pulse to

the arm wire

As a stand-alone system: The H1/3 YELLOW wire should not be connected to anything.

As an add-on car starter: If connected, disconnect the ignition/accessory input of the remote controlled secu-

rity or keyless entry system. Connect the H1/3 YELLOW ignition output to the ignition/accessory input of the

remote controlled security or keyless entry system. The wire will prevent the host system from sensing that the

ignition is on during remote engine start operation.

This input comes from the factory set to 2 activation pulses. This means that it is necessary to have 2 consecu-

H1/4 WHITE/BLUE remote engine start (-) activation input

H1/3 YELLOW (+) ignition output to RF system

H1/2 GREEN/WHITE factory alarm rearm

H1/1 LIGHT GREEN/BLACK (-) factory alarm disarm

tive ground pulses on the white/blue wire for the remote engine start to activate or to deactivate. The same holds

true for the remote control activation when set to a two pulse setting it is necessary to press the button

twice for the remote engine start to activate or deactivate.

NOTE: When the activation pulse count can be programmed to 1, 2, or 3 pulses when changed it will affect both activation inputs; the White/Blue wire and the remote control activation.

Connect this wire to the wire in the vehicle that sends the signal to turn on the WAIT-TO-START bulb in the dash-

board. In most diesels the wire is negative (ground turns on the bulb) and the GRAY/BLACK can be directly

connected to the wire in the vehicle. If the vehicle uses a positive wire (12V to turn on the bulb) a relay must

be used to change the polarity. (See Finding the Wires You Need section for testing procedures.) Here are some

common colors of this wire:

■ Chevrolet and GMC trucks: Light Blue or Dark Blue

■ Ford Trucks: Black/Pink

■ Dodge Ram Trucks: Orange/Black or Black/Orange

NOTE! A 1-amp diode must be installed in line on the factory wire between the wait-to-start indicator and the ECM. (See the following diagram for details.)

H1/5 GRAY/BLACK (-) diesel wait-to-start bulb input

This input comes from the factory set to 2 activation pulses. This means that it is necessary to have 2 consecu-

tive 12V pulses on the white/blue wire for the remote engine start to activate or to deactivate. The same holds

true for the remote control activation when set to a two pulse setting it is necessary to press the button

twice for the remote engine start to activate or deactivate.

NOTE: When the activation pulse count can be programmed to 1, 2, or 3 pulses when changed it will affect both activation inputs; the White/Red wire and the remote control activation.

When the system receives the code controlling Channel 2, for longer than 1.5 seconds, the RED/WHITE wire will

supply an output as long as the transmission continues. This is often used to operate a trunk/hatch release or

other relay-driven function.

IMPORTANT! Never use this wire to drive anything except a relay or low-current input! The transistorized output can

only supply 200 mA of current. Connecting directly to a solenoid, motor, or other high-current device will cause it

to fail.

H1/7 RED/WHITE Channel 2, (-) 200 mA output

H1/6 WHITE/RED (+) activation input

Remove any paint and connect this wire to bare metal, preferably with a factory bolt rather than your own screw.

(Screws tend to either strip or loosen with time.) We recommend grounding all your components to the same

point in the vehicle.

IMPORTANT: Do NOT connect this wire to a negative vehicle light flash wire before changing the programming jumper to the negative polarity position or damage to the vehicle light circuit may occur.

As factory configured, the H1/9 WHITE wire should be connected to the (+) parking light wire. If the light flash

polarity jumper is moved to the (-) position (refer to the Programming Jumper section of this guide), this wire

then supplies (-) 200mA output. This is suitable of driving the light control (-) circuits in Toyota, Lexus, BMW

some Mitsubishi, some Mazda, and other models.

NOTE: For parking light systems that draw 10 amps or more, the jumper must be placed to the (-) light flash output (refer to the Programming Jumpers section of this guide. P/N 8617 or a standard automotive SPDT relay must be used on the H1/2 light flash output wire.

(+) Positive Light Flash Output

H1/9 WHITE (+/-) light flash output

H1/8 BLACK (-) chassis ground connection

(-) Light Flash Output

heavy gauge relay interface

The heavy gauge wires are used to energize high current circuits in the vehicle. It is crucial that these connec-

tions are made correctly so that they are capable of handling the current demands. For this reason, scotch locks,

T-taps and other such connectors should not be used.

Remove the two 30 amp fuses prior to connecting these wires and do not replace them until the satellite has

been plugged into the control module. These wires are the source of current for all the circuits the relay satel-

lite will energize. They must be connected to a high current source. Since the factory supplies (+) 12V to the key

switch that is used to operate the motor, it is recommended that these wires be connected there.

NOTE: If the factory supplies two separate (+) 12V feeds to the ignition switch, connect one RED wire of the satellite to each feed at the switch.

Connect this wire to the ignition wire in the vehicle. (See Finding the Wires You Need section of this guide.)

Connect this wire to the accessory wire in the vehicle that powers the climate control system. (See Finding the

Wires You Need section of this guide.)

Connect this wire to the starter wire in the vehicle. (See Finding the Wires You Need section of this guide.)

PURPLE (+) starter output

ORANGE (+) accessory output

PINK (+) ignition output

RED (2) (+)12V input for relays

Connect this wire to the second ignition or accessory wire in the vehicle. (Selectable by using Feature 9.)

NOTE: For vehicles that do not have a second ignition or accessory wire, this connection is not required.

remote engine start harness (H2), 5-pin connector

Connect this wire to the toggle (override) switch as shown in Figure A. Connect the other wire from the toggle switch

to the PARK/NEUTRAL switch in the vehicle. This wire will test with ground with the gear selector either in PARK or

NEUTRAL. This will prevent the vehicle from accidentally being started while in a drive gear. This input MUST rest at ground

in order for the remote engine start system to operate. Connected properly the vehicle will only start while in PARK or

NEUTRAL.

In some vehicles, the PARK/NEUTRAL position switch activates a factory starter lock-out that will not allow the

starter to operate in a drive gear. In these vehicles, connect this wire to the toggle switch as shown in Figure B.

Connect the other wire from the toggle switch to chassis ground.

Figure A Figure B

IMPORTANT! Always use the Vehicle Safety Check section of this guide to verify that the vehicle cannot be started in ANY drive gear and that the override switch is functioning properly.

This input provides the module with information about the engine's revolutions per minute (RPMs). It can be con-

nected to the negative side of the coil in vehicles with conventional coils. In multi-coil and high energy ignition

H2/2 VIOLET/WHITE tachometer input

H2/1 BLACK/WHITE neutral safety switch input

PINK/WHITE (+) output to second ignition/accessory circuit

systems locating a proper signal may be more difficult. (See Finding the Wires You Need section of this guide for

finding the tachometer wire.) Once connected, you must teach the system the tach signal. (See Tach Learning

section of this guide.)

This wire MUST be connected to the vehicle's brake light wire. This is the wire that shows (+) 12V when the brake

pedal is depressed. The remote engine start will be disabled or shut down any time the brake pedal is depressed.

This wire MUST be connected to the hood pinswitch. This input will disable or shut down the remote engine start

when the hood is opened.

This wire supplies a 200mA output as soon as the module begins the remote engine start process. The H2/5

BLUE/WHITE wire can also be used to activate the defogger trigger (latched/pulsed) 10 seconds after successful

remote engine start. (See the Feature Descriptions section in this guide for details about programming this

output.)

neutral safety switch interface

Some vehicles combine the column shift mechanism and the mechanical neutral safety switch into one mechan-

ical part. In these vehicles, it is impossible to interface the remote engine start system before the neutral safety

switch. With this type of vehicle, if the vehicle is left in a drive gear and the remote engine start system is acti-

vated, the vehicle will move and may cause damage to persons or property.

According to available information, vehicles known to be manufactured this way are most General Motors trucks,

sport utility vehicles and column shifting passenger vehicles. Available information also indicates that pre-1996

Dodge Dakota pickups with 2.5 liter motors are also manufactured this way.

GM vehicles that have the neutral safety switch built into the column shifter can usually be identified by a purple

starter wire. Typically, vehicles that use an outboard mechanical switch use a yellow wire from the ignition switch

to the mechanical switch and a purple wire from the mechanical switch to the starter itself. Remember, this is

only a rule of thumb and is not intended as a substitute for proper testing.

IMPORTANT! Please see vehicle Safety Check section of this guide for testing procedures.

Vehicles with the neutral safety switch built into the column shifter require that the shifter be placed in park in

order to remove the keys from the ignition. As a result, it is possible to use the key-in-ignition sense switch to

H2/5 BLUE/WHITE status/defogger output

H2/4 GRAY (-) hood pinswitch input

H2/3 BROWN (+) brake switch input

prevent remote engine starting if the keys are in the ignition. (See General Motors Trucks, SUVs and Column-

Shifting Passenger Cars and Pre-1996 Dodge Dakota Pickups with 2.5 Liter Motors diagrams in this section on how

to accomplish this.) The first diagram applies to all General Motors vehicles as of the date of this guide’s publi-

cation. The second diagram applies to all pre-1996 Dodge Dakota pickup trucks with 2.5 liter motors. This

solution has one side effect: If the customer inserts the key in the ignition with the driver's door open, the

remote engine start system will shut down. If this interface is used, it is important to inform the customer that

the driver’s door must be closed before inserting the key into the ignition when the remote engine start is active.

This will allow the customer to turn the key on and shut the remote engine start down by pressing the brake,

without the key sense wire shutting down the unit prematurely.

You must also connect the H2/4 BROWN (+) shut-down input to the yellow wire on the relay satellite

ribbon cable. This prevents the remote engine start system from activating if the key is left in the “run” posi-

tion. You must use diodes to isolate the ignition circuit from the brake switch circuit as shown in the diagram

below.

IMPORTANT! Once the interface is complete, attempt to remote engine start the vehicle with the door closed and the key in the ignition. The vehicle should not start. If it does, re-check the connections.

As of the date of this guide’s publication, the following list describes the types of vehicles that are known to

have a mechanical neutral safety switch instead of an electrical neutral safety circuit. The model years will vary

from vehicle to vehicle.

■ Pre-1996 Dodge Dakota pickups with 2.5 liter engines

■ GM "B" Platform: Caprice, Impala SS and Roadmaster

■ GM "D" Platform: Cadillac Fleetwood and Fleetwood Brougham

■ GM "P" Series: Commercial Van

■ GM "L/M" Series: Astro, Safari

■ GM "C/K" Series: Full-size pickup, Sierra, Suburban, Tahoe, Yukon

■ GM "S/T" Series: Blazer, Bravada, Jimmy, pickup, Sonoma

■ GM "G" Series: Express, Savanah

YELLOW WIRE ON RELAY SATELLITE

RIBBON CABLE

(+) BRAKE WIRE

IN VEHICLE

1N4004 DIODE

BROWN (+)

SHUTDOWN INPUT

DIA-154

pre-1996 dodge dakota pickups with 2.5 liter motors

general motors trucks, SUVs, and column shifting passenger cars

bypassing GM vehicle anti-theft systems (VATS)

Vehicles with the GM VATS (Pass Key) systems have a resistor embedded in the ignition key. If the VATS decoder

module does not measure the proper resistance when the vehicle is started, the starter and fuel pump may be dis-

abled for up to ten minutes. An optional "VATS pack" of resistors is available (p/n 652T). One of the resistors in the

pack will match the resistor in the key.

The VATS wires will be two very light-gauge wires coming out of the steering column. The colors of the wires vary,

but they are often contained in orange tubing - either both will be white wires, or one wire will be purple/white

and the other white/black. Determine the value of the resistor in the key. Then follow the diagram below to

bypass VATS during remote engine start operation. If the BLUE status output from the relay satellite has been

programmed for factory security re-arm, then use the (H3/5) BLUE/WHITE 2

status output from the control

module to control the relay.

NOTE: When connecting to the VATS wires, it is not important which wire is cut.

BLUE OR

BLUE/WHITE

(+) 12V CONSTANT FUSED

PROPER RESISTOR VALUE

87A

TO IGNITION KEY SWITCH

WHITE OR PURPLE/WHITE

CUT

TO VATS DECODER MODULE

WHITE OR WHITE/BLACK

1995 and newer vehicle anti-theft systems (immobilizers)

1995 and newer vehicle anti-theft systems (immobilizers) require a bypass module. The bypass module allows for

easy interfacing, while still maintaining the OEM system’s integrity.

The Passlock I and Passlock II systems can be found in the following General Motors vehicles:

■ ‘95 and newer Cavalier and Sunfire

■ ‘96 and newer Achieva, Grand Am, and Skylark

■ ‘97 and newer Intrigue, Malibu, and Cutlass

■ ‘98 and newer trucks, vans, SUVs

■ ‘99 and newer Alero

■ 2000 and newer Impala and Saturn

Passlock I and II systems are VATS-evolved. Passlock systems still rely on the R-code to start, but the pellet is no

longer placed in the key. The resistor can now be found in the key switch. This allows for a greater number of

possible R-codes. In addition, Passlock systems require “seeing” the correct R-code at the correct time. To bypass

Passlock I and II, p/n 555L or p/n 555T is required.

The Passkey III system can be found in the following vehicles:

■ ‘97 and newer Park Avenue

■ ‘98 and newer Cadillac

■ ‘99 and newer U vans, Transport, Montana, and Silhouette

■ 2000 and newer Grand Prix, Lesabre, Monte Carlo, Lumina, Bonneville

■ 2001 and newer Aurora, Aztek and Rendezvous

Other transponder-based systems include: Acura, BMW, Dodge/Chrysler/Jeep, Ford, Honda, Infinity, Mazda,

Mercedes, Mitsubishi, Nissan, Toyota, Volkswagon, and Volvo.

PK-3 and the transponder-based systems use a transponder system that locks out the ignition and fuel system.

This transponder system is comprised of two parts. The first part, the transceiver, circles the key switch and is

activated when the key is placed in the key switch or turned to the run position. Upon activation, the transceiver

passkey III (PK-3), transponder-based systems

passlock I and passlock II (PL-1 and PL-2)

will excite the transponder, which is located (but not visible) in the head of the ignition key. The key transpon-

der will then send a unique code back to the transceiver for evaluation. If the code matches a valid code of the

system, the vehicle will be allowed to start. Most of these transponder-based systems can be bypassed using p/n

555U. Some may require additional parts from the vehicle manufacturer. Consult you dealer for the applications.

For most Ford PATS transponders, p/n 555F can be used, except for the following vehicles, which will require p/n

555U: ‘97 and newer Mark VII, and 2000 and newer Taurus/Sable, Contour/Mystique and Focus.

optional anti-grind relay

The anti-grind relay prevents the starter from engaging if the ignition key is accidentally turned to the start posi-

tion during remote engine start operation.

programming jumpers

This jumper is used to determine the light flash output polarity. In the (+) position, the on-board relay is enabled

and the unit will output (+)12V on the WHITE wire, H1/2. In the (-) position, the on-board relay is disabled. The

WHITE wire, H1/2, will supply a 200mA (-) output suitable for driving factory parking light relays.

NOTE: For parking light circuits that draw 10 amps or more, the internal jumper must be switched to a (-) light flash output. P/N 8617 or a standard automotive SPDT relay must be used on the H1/2 light flash output harness wire.

In most cases, this jumper can be left in the OFF position. Some new vehicles use less than 12 volts in their

ignition systems. The unit may have trouble learning the tach signal in these vehicles. Changing the jumper to

the ON setting changes the trigger threshold of the digital tach circuit so it will work properly with these vehi-

cles. The vehicles affected include many newer Dodge/Chrysler/Plymouth vehicles, such as the Neon, Cirrus,

Stratus, Breeze and LH-based vehicles.

tach threshold on/off

light flash (+)/(-)

plug-in program switch

The Program switch plugs into the blue two-pin connector.

transmitter/receiver learn routine

The system comes with one transmitter that has been taught to the receiver. The receiver can store up to 4 dif-

ferent transmitter codes in memory. Use the following learn routine to add transmitters to the system or to

change button assignments if desired.

The Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to

remember whenever programming this unit: Key, Choose, Transmit and Release.

1. Key. Turn the ignition to the ON position.

2. Choose. Within 10 seconds, press and release the Program switch the number of times cor-

responding to the desired channel listed below. Once you have selected the channel, press

the switch once more and HOLD it. The LED will flash to confirm the selected channel. Do

not release the Program switch.

auto learn transmitter configuration

/ button one .......................lock/unlock

button two .......................Channel 2

OPT button three .....................No function

button four.......................remote engine start

/+ buttons one and two..........timer mode

/+ buttons one and four .........turbo start/short run

/++ buttons one, two and four ....rear defogger on/off

3. Transmit. While HOLDING the Program switch, press the button on the transmitter that you

would like to control the selected receiver channel.

4. Release. Once the code is learned, the Program switch can be released.

You can advance from programming one channel to another by releasing the Program switch and tapping it to

advance steps and then holding it. For instance: You have programmed Channel One and you want to program

Channel Two. Release the Program switch. Press it one time and release it to advance from Channel One to

Channel Two. Now, press and HOLD the Program switch. The LED will flash two times. As before, do not release

it.

If you want to program Channel Three after programming Channel One, release the Program switch, press it twice

and release it to advance to Channel Three. Then press it once more and HOLD it. The LED will flash three times

to confirm it is ready to receive the code from the transmitter.

Learn Routine will be exited if:

■ Ignition is turned off.

■ Program switch is pressed too many times.

■ More than 25 seconds elapses between programming steps.

CHANNEL NUMBER FUNCTION

1 Auto-Learn*

2 Lock/Unlock

3 Channel 2 output

4 remote engine start

5 Turbo/Short Run

6 Timer Mode

7 Defogger Control

8 Delete all Transmitters**

*NOTE: For Auto Learn Configurations, see Transmitter Configurations section of this guide.

**NOTE: If any button from a known transmitter is programmed to Channel 8, all transmitters will be erased from memory and will revert to the default feature settings. This is useful in cases where the customer's transmitters are lost or stolen.

tach learning

1. Start the vehicle with the key.

2. Within 5 seconds, press and HOLD the Program switch.

3. The LED will light constant when the tach signal is learned.

4. Release the Program switch.

operating settings learn routine

The System Features Learn Routine dictates how the unit operates. The programmable operating settings of this

unit can be changed whenever necessary through the computer-based Learn Routine. The Program push-button

switch, plugged into the blue port, is used together with a programmed transmitter to change the settings. It is

possible to access and change any of the feature settings using the Program switch. To program settings, remem-

ber: Key, Choose, Transmit and Release.

To program the learn routine:

1. Key. Turn the ignition on and then back off.

2. Choose. Within 10 seconds, press and release the Program switch the number of times cor-

responding to the feature number you want to program. (See Features Menu section.)

Once the Program switch has been pressed and released the desired number of times, press it once more and

HOLD it. After a second, the LED will flash to indicate which feature you have accessed. For example, groups of

eight flashes would indicate access to the status output feature (Feature 8).

to learn the tach signal

DRW-96

3. Transmit. The transmitter is used to select the desired setting. As shipped, the unit is con-

figured to the LED ON settings. These are called the default settings. Pressing Channel One

(usually Button I) will set it to the LED ON setting. The LED will light solid (stop flashing)

to indicate the setting. Pressing Channel 2 (usually Button II) will change the setting to

the LED OFF setting. The LED will go out indicating the change.

4. Release. The Program switch can now be released.

You can advance from feature to feature by pressing and releasing the Program switch the number of times nec-

essary to get from the feature you just programmed to the feature you wish to access. For example, if you just

programmed the run time (Feature 3) and you next want to program parking lights (Feature 4) to constant,

release the Program switch. Press and release it once to advance from Feature 3 to Feature 4. Then press it once

more and HOLD it. The LED will flash in groups of 4 to confirm that you have accessed Feature 4.

The learn routine will be exited if any of the following occurs:

■ The ignition is turned on.

■ The Program switch is pressed too many times.

■ More than 25 seconds elapses between programming steps.

features menu

The factory default settings are indicated in bold text in the table below.

FEATURE DEFAULT - LED ON SETTING LED OFF SETTING

NUMBER (PRESS CHANNEL 1) (PRESS CHANNEL 2)

1 Engine checking on Engine checking off

2 Tachometer checking type Voltage checking type

3 12 minutes run time (1)* 24 minutes (2)*, 60 minutes (3) run time

4 Flashing parking light output Constant parking light output

5 Cranking time 0.6 sec. (1) Cranking time 0.8 (2), 1.0 (3), 1.2 (4), 1.4 (5),

1.6 (6), 1.8 (7), 2.0 (8), 4.0 (9) sec.

6 Voltage check high level Voltage check low level

7 Short Run (turbo timer): 1 (1) min Short Run (turbo timer) 3 (2), 5 (3), 10 (4) min.

8 Activation pulse: 1 (1) Activation pulses: 2 (2), 3 (3)

9 Ignition/accessory output: Ignition Ignition/accessory output: Accessory

10 Accessory state during wait to start: OFF Accessory state during wait to start: ON

11 2ndstatus output: Normal (1) Rear defogger latched (2)/pulsed (3)

12 Diesel timer Wait-to-Start input (1) Timed 15 (2), 30 (3), 45 (4) seconds

13 Run Time (Timer Mode) 12 minutes (1) 3 (2), 6 (3), 9 (4) minutes

14 Door Lock pulse duration 0.8 seconds (1) 3.5 (2), 0.4 (3) seconds

15 Unlock output 1 pulse Unlock output 2 pulses

16 Lock output 1 pulse Lock output 2 pulses

17 Ignition unlock ON Ignition unlock OFF

18 Ignition lock ON Ignition lock OFF

19 Factory Alarm Disarm with unlock Before Unlock (2)/remote engine start only (3)

20 Factory Alarm Disarm 1 pulse 2 pulses

21 Comfort Closure ON OFF

*NOTE: The number in parentheses indicate the number of times the LED will flash

feature descriptions

The features of the system are described below.

1 ENGINE CHECK—ON/OFF: In the default setting the remote engine start will monitor either the vehicle's tach

wire or voltage depending on the programming of Feature 2. If programmed off, the vehicle will crank for the pro-

grammed crank time (Feature 5) and will not verify with tach or voltage that the vehicle is running. In the off

setting, if the vehicle fails to start, the ignition can stay on for the entire run duration. Using tach or voltage

check is always recommended if possible.

2 TACH WIRE SENSE/VOLTAGE SENSE: If the tachometer signal wire is used, this feature must be left in the default

(tach wire connected) setting. If programmed to the voltage sense setting, the unit will crank the starter for a

preset time that can be programmed in Feature 5. Once the starter has been engaged, the system will check the

voltage level to verify the engine is running. The threshold for the voltage level test can be programmed in

Feature 6. When using voltage sense mode, connection of the H2/5 VIOLET/ WHITE tachometer input is not necessary.

3 RUN TIME—12/24/60 MINUTES: This feature controls how long the engine will run before it “times out” and

shuts down. Programmed to the default setting the engine will run for 12 minutes. If the 24 or 60 minute run

time is desired, change this feature to the two or three flash setting.

4 PARKING LIGHTS—FLASHING/CONSTANT: In the default setting, the unit will flash the vehicle’s parking lights

while remote engine started. The constant setting will turn the parking lights on solidly for the entire run dura-

tion.

5 CRANK TIME—0.6/0.8/1.0/1.2/1.4/1.6/1.8/2.0/4.0 SECONDS: If Feature 2 is programmed to the voltage

sense setting, the crank time must be set to the appropriate duration. The default setting is 0.6 second. If a dif-

ferent crank time is desired, select Feature 5 and (while pressing the Program switch) press the Channel Two

button to advance through the LED Off settings. The unit will flash the LED to indicate which time is selected.

Once the 4.0 second setting is reached the next press of the Channel Two button will reset the system to the

shortest setting.

6 VOLTAGE CHECK LEVEL—HIGH/LOW: This feature only functions when Feature 2 is programmed to voltage

sense. Some vehicles have many accessories, which are turned on when remote engine started. In these vehicles,

the variation of voltage between the engine off and the vehicle running is very slight and the remote engine start

unit may “think” the vehicle has not started. This can cause the remote engine start to shut down after the

vehicle has been started. If this is the case, program this feature to the LOW position.

7 SHORT RUN (TURBO TIMER)—1/3/5/10 MINUTES: When the and buttons on the transmitter are

pressed simultaneously while the engine is running, the vehicle will continue to run for the short run time. The

factory default is 1 minute.

8 ACTIVATION PULSE COUNT—1/2/3 PULSES: This feature allows the number of pulses to activate the remote

engine start feature to be changed from 1, 2, or 3 pulses. The pulse count programmed to start the vehicle will

also be the same required to shut down the remote engine start.

9 2nd—IGNITION/ACCESSORY OUTPUT: This will allow the PINK/WHITE to be used as a 2ndignition or a

2ndaccessory.

10 ACCESSORY STATE DURING WAIT-TO-START—OFF/ON: This will allow the programming of the accessory wire

during the wait-to-start period of a diesel motor. When ON the accessory comes on when the wait-to-start output

is activated and stays on, dropping out during crank and returning once the car has started. When OFF the acces-

sory will activate as a normal accessory.

11 2ndSTATUS OUTPUT—NORMAL/LATCHED/PULSED: If programmed to status mode, this output will turn on

when the remote engine start is activated. In this mode the output can be programmed to a latched or a pulsed

output. The pulsed ouput turns the defogger ON. When programmed to the latched output the status will only

stay active for 10 minutes. Both outputs activate 10 seconds after remote engine start.

12 DIESEL TIMER—WAIT-TO-START/15, 30, 45 SECONDS: Default is the “Wait-to-Start” input control wire, or

programmable to ignore the input control wire by a delay of 15, 30, or 45 seconds.

13 RUN TIME (TIMER MODE)—12, 3, 6, 9 MINUTES: Selects the time in minutes that the system will operate

the engine until the system "times out". This is the maximum operation period and the system may be shut down

using a shutdown at any time.

14 DOOR LOCK PULSE DURATlON—0.8, 3.5, 0.4 SECONDS: Some European vehicles, such as Mercedes-Benz and

Audi, require longer lock and unlock pulses to operate the vacuum pump. Programming the system to provide 3.5

second pulses, will accommodate the door lock interface in these vehicles. The default setting is 0.8 second door

lock pulses. Some modification to the door lock harness (H2) is also necessary. (Refer to TechTip 1041 for wiring

information regarding (+/-) Door Lock Outputs Harness (H4)section, Type E - Mercedes-Benz and Audi -1985 and

Newer" diagram.) The 0.4 second pulse is required on some of the newer Chrysler and Ford vehicles.

15 UNLOCK OUTPUT—1, 2 PULSES: This will program the unlock output to one or two pulses. When the double

pulse unlock feature is turned on, the BLUE (3) wire will supply two negative pulses instead of a single pulse.

This makes it possible to directly interface with double pulse vehicles without any extra parts.

16 LOCK OUTPUT—1, 2 PULSES: This will program the lock output to one or two pulses. The GREEN (1) wire will

supply two negative pulses instead of a single pulse. This makes it possible to directly interface with double pulse

vehicles without any extra parts.

17 IGNITION CONTROLLED UNLOCK—ON, OFF: When programmed ON the doors will unlock automatically when the

key is turned off.

18 IGNITION CONTROLLED LOCK—ON, OFF: When programmed ON the doors will lock when the key is on and all

doors are closed.

19 FACTORY ALARM DISARM—WITH UNLOCK, BEFORE UNLOCK, remote engine start ONLY: In the default setting the

factory alarm disarm output will disarm the factory alarm system any time the button(s) controlling Unlock is pressed.

The “Before Unlock” output to disarms the factory alarm before the unlock output activates and before remote engine

start is activated. The “remote engine start Only” output disarms the factory alarm only before the remote engine

start is activated.

20 FACTORY ALARM DISARM PULSES—SINGLE, DOUBLE: Selectable for a single or double-pulse for the vehicle’s

factory alarm disarm input requirements.

21 COMFORT CLOSURE—ON, OFF: The system can be programmed to close the windows when the system is armed.

A 20-second output starts 200mS after the last lock pulse. The Comfort Closure output will be canceled if the unlock

button is pressed. If programmed ON, the lock output wire provides this function.

shutdown diagnostics

The unit has the ability to report the cause of the last shutdown of the remote engine start system. To enter diag-

nostic mode:

1. Turn the ignition off.

2. Press and HOLD the Program switch.

3. Turn the ignition on and then off.

4. Release the Program switch.

5. Press and release the Program switch.

The LED will now report the last system shutdown by flashing for one minute in the following grouped patterns:

The LED will stop flashing when the ignition is turned on.

rear defogger control

The rear defogger output can be remotely turned on/off any time using the remote control. The default setting

is ON.

To turn the rear defogger output OFF:

1. Press & release the / and and buttons of the remote control.

2. The parking lights will flash 2-times.

3. The rear defogger output will no longer activate when the vehicle is remote engine started.

NOTE: If the remote engine start is On the lights will turn off then flash 2-times before returning to their normal output and the defogger output, if active, will cease.

To turn the rear defogger output ON:

1. Press & release the / and and buttons of the remote control.

2. The parking lights will flash 3-times.

3. The rear defogger output will once again activate when the vehicle is remote engine started.

NOTE: If the remote engine start is On the lights will turn off then flash 3-times before returning to their normal output and the defogger output will activate as programmed.

LED SHUTDOWN FLASHES MODE

One System timed out

Two Over-rev shutdown

Three Low or no RPM

Four Transmitter Shutdown (or optional push-button)

Six (+/-) Shutdown

Seven (-) Neutral safety shutdown (H2/6 BLACK/WHITE)

Eight Wait-to-start timed out

timer mode

By pressing the remote / and buttons simultaneously the parking lights will flash 4 times and

then start the vehicle and run for the set duration. The remote engine start can be shut off by the transmitter by

pressing the remote engine start button and remain in timer mode, but if any other shut down zones or the

ignition becomes active the timer mode will cancel.

1. Press Timer mode buttons.

2. The vehicle will confirm with 4 parking light flashes.

3. A 1-second delay will start.

4. The system will start the car and will run for the specified duration, unless shut down by the remote engine

start button (or the +/- input).

5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires (a

maximum of 6 times).

IMPORTANT! Timer Mode should be used only in open areas. Never start and run the vehicle in an enclosed space such as a garage or carport.

safety check

Before vehicle reassembly, the remote system must be checked to ensure safe and trouble-free operation. The fol-

lowing test procedure must be used to verify proper installation and operation of the system. The installation

must be completed before testing, including connection to the brake switch and hood switch.

1. Test the BRAKE shutdown circuit: With the vehicle in Park (P), activate the remote engine start system. Once

the engine is running, press the brake pedal. The engine should shut down immediately. If the engine con-

tinues to run, check the brake circuit connection.

2. Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the hood. Activate the remote engine

start system. The vehicle should not start. If the starter engages, check your hood pin and connections.

NOTE: If programmed for Diesel Mode, the system will turn on the ignition, but the starter should not engage with the hood open.

3. Test the NEUTRAL SAFETY shutdown circuit:

IMPORTANT! Make sure there is adequate clearance to the front and rear of the vehicle before attempting this test.

a. Make sure the hood is closed and no other shutdown circuits are active.

b. Set the emergency brake.

c. Turn the ignition key to the run position but do not start the engine.

d. Put the vehicle in Drive (D).

e. Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake to shut-

down the remote engine start system.

f. Activate the remote engine start system.

■ If the starter engages, immediately step on the brake to shut down the system. If it does engage,

recheck the neutral safety input connection. The vehicle may use a mechanical neutral safety switch.

(See H2/6 BLACK/WHITE neutral safety switch input in remote engine start Harness Wire Connection

Guide section of this guide.)

■ If the starter does not engage, the test is complete.

Once the system passes all three tests, the vehicle can be re-assembled and delivered. Do not the use the remote

engine start system or finalize the installation if it fails any of the safety check tests.

troubleshooting

■ The ignition comes on, but the starter will not crank.

Does it start with the key in the ignition? If so, does the vehicle have a VATS Pass-Key system?

Will it start with the brake pedal depressed? (Make sure to disconnect the brake shutdown when performing this

test.) If so, it may have a brake/starter interlock.

Is the correct starter wire being energized? Check by energizing it yourself with a fused test lead.

■ The starter cranks for six seconds but does not start.

Either the wrong ignition wire is being energized, the system’s ignition and accessory wires have been connected

backwards, or the vehicle has two ignition circuits. Try activating the unit with the ignition key in the “run” posi-

tion. If the vehicle then runs normally, retest your ignition system.

■ The starter continues to crank even though the engine has started.

Has the tach wire been learned? See the Tach Learning section of this guide.

Is the tach wire receiving the correct information? Either the wrong tach wire has been used, or a bad connec-

tion exists.

■ The climate control system does not work while the unit is operating the vehicle.

Either the wrong accessory wire is being energized or more than one ignition or accessory wire must be ener-

gized in order to operate the climate control system.

■ The remote engine start will not activate.

1. Check harnesses and connections. Make sure the harnesses are fully plugged into the remote engine start

module. Make sure there are good connections to the vehicle wiring.

2. Check voltage and fuses. Use a meter and check for voltage between the red wire in the 5 pin ribbon harness

and the black ground wire. If you have less than battery voltage, check the 3A and both 30A fuses on the

relay satellite. Also make sure that the ground wire is going to a chassis ground and not to something under

the dash.

3. Check diagnostics. The diagnostics will tell you which shutdown is active or not connected.

■ The remote engine start will activate but the starter never engages.

1. Check for voltage on the purple starter wire two seconds after the remote engine start becomes active. If

there is voltage present, skip to Step 4. If there is not voltage present, advance to Step 2.

2. Check the 30A fuses.

3. Check diagnostics. If the gray/black wire is detecting ground upon activation, the starter will not crank.

4. Make sure the purple starter wire is connected on the starter side of the optional starter kill relay.

5. Does the vehicle have an immobilizer? Some immobilizer systems will not allow the vehicle to crank if active.

6. Check connections. The two red heavy gauge input wires on the relay satellite should have solid connections.

"T-taps", or "scotch locks" are not recommended for any high current heavy gauge wiring. Also, if the vehicle

has more than one 12-volt input wire, then connect one red wire to each.

■ The vehicle starts, but immediately dies.

1. Does the vehicle have an immobilizer? The vehicle’s immobilizer will cut the fuel and/or spark during unau-

thorized starting attempts.

2. Is the remote engine start programmed for voltage sense? If so, the start time may not be set high enough,

or you may have to adjust the voltage threshold in programming. Voltage sense will not work on some vehi-

cles.

3. Check diagnostics. Sometimes a shutdown will become active during cranking or just after cranking.

■ The vehicle starts, but the starter keeps running.

1. Is the system programmed for engine checking off or voltage sense? When programmed for either of these

features, the engine cranks for the preprogrammed crank time regardless of how long it takes to start the

vehicle to actually start. Adjust to a lower cranking time.

2. Was the Tach Learn successful? The LED must light solidly and brightly to indicate a successful learn.

3. Make sure that there is a tach signal right at the purple/white tach input wire of the remote engine start. If

not, recheck the connection to the vehicle’s tach wire and make sure the wire is not broken or shorted to

ground leading to the remote engine start.

■ The vehicle will start and run only for about 10 seconds.

1. Is the remote engine start programmed for voltage sense? Try programming the unit for low voltage refer-

ence. If this does not work, a tach wire should be used.

2. Check diagnostics.

■ Diesel vehicle does not wait to start.

1. Is the GRAY/BLACK wire connected to the wait-to-start wire of the vehicle?

2. Check the polarity of the wait-to-start wire. (See the Finding the Wait-to-Start Bulb Wire For Diesels section

of this guide.)

3. If wiring a negative wait-to-start bulb, make sure that a diode has been placed in line on the factory wire

between the vehicle’s ECM and the wait-to-start bulb. (See wiring description for the H1/6 GRAY/BLACK (-)

Diesel Wait-To-Start Bulb Input of the Primary Harness Wire Connection Guide.)

wiring quick reference guide

Get Started

Get Protected

Ungo Pro Security 661 W. Redondo Beach Blvd. Gardena, Ca. 90247

800-GO-CLARION

Clarion ProSecurity RS10 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual