Clarion pro audio vrx 630 Owners & Installation Manual
All Rights Reserved. Copyright © 2003: Clarion Co., Ltd.
Printed in China / Imprimé en Chine / Gedruckt in China / Stampato in Cina
Gedrukt in China / Impreso en China / Tryckt i Kina / Impresso na China
2003/01 (D·C)
QC-6710B
280-7946-00
Clarion Co., Ltd.
6.5” MONITOR & FM/AM RADIO WITH CD/MD/DVD
CHANGER CONTROL
•
MONITEUR DE 6,5 POUCES ET RADIO FM/AM AVEC
COMMANDE DE CHANGEUR DE CD/MD/DVD
•
MONITOR DE 6,5-PULGADAS Y RADIO FM/AM CON
MANDO PARA EL CAMBIADOR DE CD/MD/DVD
Owner’s manual & Installation manual
Mode d’emploi et manuel d’installation
Manual de instrucciones y de instalación
VRX630
2 VRX630 VRX630 xx
280-7946-00
280-7946-00
Contents
1. PRECAUTIONS ....................................... 4
2. CAUTIONS ON HANDLING ....................4
LCD panel/Generalities............................4
Cleaning ................................................... 4
3. CONTROLS ............................................. 5
4. NOMENCLATURE................................... 6
Names of Buttons..................................... 6
JOYSTICK Operation............................... 7
5. MODE DISPLAY ...................................... 8
Display common to each mode ............... 8
TITLE LIST mode display ........................ 8
RADIO mode display................................ 9
RDS mode display ................................... 9
CD/MD Changer mode display .............. 10
TV mode display .................................... 10
6. DCP ........................................................ 11
7. REMOTE CONTROL ............................. 12
Inserting the Batteries ............................ 12
Functions of Remote Control Unit
Buttons ............................................... 13
Thank you for purchasing the Clarion VRX630.
∗This owner’s manual is for the VRX630.
∗Please read this owner’s manual in its entirety before operating this equipment.
∗After reading this manual, be sure to keep it in a handy place (e.g., glove compartment).
∗Check the contents of the enclosed warranty card and keep it carefully with this manual.
∗This manual includes the operating procedures of the CD changer, MD changer, D VD changer, TV
tuner connected via the CeNET cable. The CD changer , MD changer , DVD changer, TV tuner ha v e
their own manuals, but no explanations for operating them are described.
8. OPERATIONS........................................ 15
Basic Operations.................................... 15
Radio Operations ................................... 18
CD Changer Operations ........................ 23
MD Changer Operations ........................ 25
DVD Changer Operation........................ 27
TV Operations ........................................ 31
CCD Camera.......................................... 39
Connecting other company’s image
equipment........................................... 40
Other Functions...................................... 40
DSP Operations ..................................... 31
9. IN CASE OF DIFFICULTY..................... 43
10. ERROR DISPLAYS................................ 45
11. SPECIFICATIONS ................................. 46
280-7917-00
English
Owner’s manual
English
Owner’s manual
English
Owner’s manual
Be sure to unfold and read the next page. / Veuillez déplier et vous référer à la page suivante.
Cerciórese de desplegar y de leer la página siguiente.
VRX630 4VRX630 3
TITLE LIST mode display
COLOR LCD DISPLAY INFORMATION PANEL
5. MODE DISPLAY
The Color LCD Display and the Information Panel on the main unit show the following displays , providing information about the mode and functions operated.
Display common to each mode
COLOR LCD DISPLAY INFORMATION PANEL
Clock Time display
MAIN
8 VRX630
1. PRECAUTIONS
1. This unit uses a precision mechanism. Even
in the event that trouble arises, never open
the case, disassemble the unit, or lubricate
the rotating parts.
2. TV broadcast reception
When receiving the TV broadcasts, the
strength of the signals changes since the car
is moving, so in some cases it may not be
possible to receive clear pictures.
• TV signals are strongly linear, so reception
is affected by buildings, mountains and
other obstacles.
• Such external factors such as electric train
lines, a high voltage lines, and signal devices may disturb the picture or cause
noise.
∗ If the reception is poor, switch to a station with
good reception.
!
W ARNING
For your safety, the driver should not watch the TV or operate the controls while driving.
Please note that watching and operating the TV while driving are prohibited by law in
some countries. Also, while driving, keep the volume to a level at which external sounds
can be heard.
2. CAUTIONS ON HANDLING
LCD panel/Generalities
•
Be sure to store the LCD panel inside the
main unit when parking the car outdoors for
long period of time. The LCD panel will operate properly in a temperature range of 0 to
60°C.
• Don’t allow any liquids on the set from drinks,
umbrellas etc. Doing so may damage the internal circuitry.
• Do not disassemble or modify the set in any
way. Doing so may result in damage.
• Do not draw the LCD panel out and use it as
a tray. Also, subjecting the LCD panel to
shocks may result in breakage, deformation
or other damage.
• Do not let cigarettes burn the display. Doing
so may damage or deform the cabinet.
• If a problem should occur, have the set inspected at your store of purchase.
• Do not insert objects or poke in the space
between the LCD panel and the main unit
when the panel is tilted.
• Do not place anything on the display when
the panel is tilted.
• The remote controller may not work if the remote control sensor is exposed to direct sunlight.
• In extremely cold weather , the displa y movement may slow down and the display may
darken, but this is not a malfunction. The display will work normally when the temperature
increases.
• Small black and shiny spots inside the LCD
panel are normal for LCD products.
• The LCD panel may stop temporarily when it
opens or closes, when the engine stops or
when it is cold.
Cleaning
• Cleaning the cabinet
Use a soft, dry cloth and gently wipe off the
dirt. For tough dirt, apply some neutral detergent diluted in water to a soft cloth, wipe off
the dirt gently, then wipe again with a dry cloth.
Do not use benzene, thinner, car cleaner, etc.,
as these substances may damage the cabinet
or cause the paint to peel. Also, leaving rubber or plastic products in contact with the cabinet for long periods of time may cause stains.
• Cleaning the LCD panel
The LCD panel tends to collect dust, so wipe it
off occasionally with a soft cloth. The surface is
easily scratched, so do not rub it with hard objects.
For a longer service life, be sure to read the following cautions.
286-6215-00
Clarion Co.,Ltd.
MADE IN CHINA
SERIAL No.
QC-6710B
VRX630
MODEL
AM 530-1710kHz/FM 87.9-107.9MHz
12V GROUND
ISO
8mmMAX
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
286-6215-00
Clarion Co.,Ltd.
MADE IN CHINA
SERIAL No.
QC-6710B
VRX630
MODEL
AM 530-1710kHz/FM 87.9-107.9MHz
12V GROUND
ISO
8mmMAX
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS
PRODUCT NOT APPROVED BY THE
MANUFACTURER WILL VOID THE
WARRANTY AND WILL VIOLATE FCC
APPROVAL.
280-7946-00_Eng(3-8) 1/17/03, 2:17 PM3
280-7917-00
5 VRX630 6 VRX630 VRX630 7
English
Owner’s manual
English
Français
Español
English
Owner’s manual
4. NOMENCLATURE
Note:
• Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold).
Names of Buttons
1 POWER button
FNC (Function) button
2 SEARCH button
VOLUME button
a button
d button
3 PLAY/PAUSE button
4 Information Panel
5 PS (Preset scan)/AS (Auto store) button
SCN (Scan) button
6 DCP RELEASE lever
7 WIDE button
RPT (Repeat) button
8 TV/VTR button
RDM (Random) button
9 Z-EHCR (Z-enhancer) button
0 ISR button
! OPEN button
MONI LOCK (Monitor lock) button
@ DISP (Display) button
# PRESET buttons (1 to 6)
DIRECT buttons (1 to 6)
$ MUTE button
% BND (Band) button
¥ Color LCD display
& A-M (Audio-Mode) button
* ADJ (Adjust) button
( TITLE button
) VISUAL button
¡ JOYSTICK
™ Remote Control Infrared Sensor
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.
Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.
3.
CONTROLS / COMMANDES / REGLER / CONTROLLI
REGELAARS / CONTROLES / KONTROLLER
Main unit / Unité principale / Unidad principal
With the Display closed / Avec l`afficheur fermé / Con el visualisador cerrado
With the Display open / Avec l`afficheur ouvert / Con el visualisador abierto
JOYSTICK Operation
With the display closed With the display open
Note:
• Many settings/procedures have to be performed by using the JOYSTICK
¡
. Be sure to read this chapter
in order to operate it properly.
• In the DVD changer mode, items for menu display, etc. can be selected by operating the JOYSTICK
¡
upward, downward, leftward or rightward.
● Selecting an item in the menu
Select an item displayed in the menu by operating the JOYSTICK ¡ upward or downward.
● Setting an option for the selected item
When the setting options for an item are listed
on the right of the display, you can choose the
desired option by operating the JOYSTICK ¡
leftward or rightward. Then, press the center of
the JOYSTICK ¡ to set your choice.
● When “push NEXT” is displa yed next to the
menu item
1. Press the ENT at the center of the JOYSTICK
¡ to select the item and show the setting
display for this item.
2. Operate the JOYSTICK ¡ upward or downward to select the desired setting option, then
press ENT at the center of the JOYSTICK ¡
to set your choice.
● Returning to the previous mode
Select the item “MENU” by operating the JOYSTICK ¡ leftward or rightward, then press the
ENT at the center of the JOYSTICK ¡.
4 6 7 8
$% @
9
5
3
1
0
!
#
2
) (¡ *™ &
¥
280-7946-00_Eng(3-8) 1/17/03, 2:17 PM4
VRX630 9
English
Owner’s manual
RADIO mode display
MAIN
SUB
CD/MD Changer mode display
SUB
MAIN
INFORMATION PANELCOLOR LCD DISPLAY
COLOR LCD DISPLAY INFORMATION PANEL
10 VRX630
English
Owner’s manual
TV mode display
COLOR LCD DISPLAY INFORMATION PANEL
SUB
MAIN
D VD Changer mode display
COLOR LCD DISPLAY INFORMATION PANEL
DVD
MAIN
While the car is moving, the screen below is displayed.
• No sub-indication
VRX630 11
English
Owner’s manual
2. Lock the DCP/Operation Panel at the upper
center until a click is heard.
3. Press the power button 1 to turn on the
power.
∗ The unit will not accept any key inputs for 1 sec-
ond after the DCP has been reattached.
CAUTION
• The DCP can easily be damaged by shocks.
After removing it, be careful not to drop it
or subject it to strong shocks.
• If the Operation Panel is kept open, the DCP
may drop due to vibration of the car. This
results in damage to the DCP. So close the
Operation Panel or remove the DCP to store
into the case.
• The connector connecting the main unit and
the DCP is an extremely important part. Be
careful not to damage it by pressing on it
with fingernails, screwdrivers, etc.
Note:
• If the DCP is dirty, wipe off the dirt with a soft, dry
cloth only.
The control panel can be detached to prevent
theft. When detaching the control panel, store it
in the DCP (DETACHABLE CONTROL PANEL)
case to prevent scratches.
We recommend taking the DCP with you when
leaving the car.
Removing the DCP
1. Turn the power off.
2. Deeply push in the DCP RELEASE lever 6
to release the DCP/Operation Panel.
6. DCP
3. Pull the DCP toward you and remove it.
Attaching the DCP
1. Hold the DCP/Operation Panel with its rear
side facing the main unit and, as shown in the
figure below, put the lower edge of the panel
onto the corresponding edge of the main unit.
DCP/RALEASE lever
DCP/Operation Panel
POWER button
12 VRX630
English
Owner’s manual
Inserting the Batteries
1. Turn the remote control unit over, then slide
the rear cover in the direction of the arrow.
2. Insert the AA (SUM-3, IECR-6/1.5V) batteries that came with the remote control unit
facing in the directions shown in the figure,
then close the rear cover.
Notes:
Using batteries improperly can cause them to explode.
Take note of the following points:
• When replacing batteries, replace both batteries
with new ones.
• Do not short-circuit, disassemble or heat batteries.
• Do not dispose of batteries into fire or flames.
• Dispose of spent batteries properly.
7. REMOTE CONTROL
Remote control unit
When the panel is open
VRX630 13
English
Owner’s manual
Functions of Remote Control Unit Buttons
Notes:
• In the DVD changer mode, the remote control unit can not work for some items.
• Please use the dedicated remote control in the DVD changer mode.
(
∗
)In the DVD changer mode, this remote control unit mak es the same operation as that perf ormed using the
button with the same name on the remote control unit for the DVD changer.
Button
Mode
Radio
£ FUNC
¢ BAND
DISC UP
TOP
∞ VOLUME
§ SEARCH
¶ PLAY/PAUSE
• MUTE
ª ISR
º DISP
MONI
⁄ PS/AS
SCN
¤ WIDE
RPT
‹ TV/VTR
RDM
› VISUAL
Switches reception band.
Moves preset channels
up and down.
No function.
Preset scan.
When pressed and held
for 2 seconds: Auto store.
No function.
No function.
Moves to the next disc in
increasing order.
Moves tracks up and
down.
When pressed and held
for 1 second:
Fast-forward/
Fast-backward.
Switches between
playback and pause.
Scan play.
When pressed and held
for 1 second: Disc scan
play.
(∗)
Repeat play.
When pressed and held
for 1 second: Disc repeat
play.
(∗)
Random play.
When pressed and held
for 1 second: Disc
random play.
(∗)
Switches reception band.
Moves preset channels
up and down.
No function.
Preset scan.
When pressed and held
for 2 seconds: Auto store.
Switches TV display size.
Switches the VISUAL
mode.
Switches between TV
and VTR.
Turns mute on and off.
ISR on and off. Press and hold for 2 seconds or longer: Stores current station
into ISR memory.
Turns on and off the monitor.
When pressed and held for 1 second or longer in the DVD changer mode:
switches the display size.
Switches among Radio, CD changer, MD changer, DVD changer and TV.
Turns power on and off. When pressed and held for 1 second: Turns power off.
Switches the VISUAL mode. In the DVD changer mode, you can not use this
function.
TV
CD changer
MD changer
DVD changer
Increases and decreases volume (in all modes).
14 VRX630
English
Owner’s manual
8. OPERATIONS
Basic Operations
Note: Be sure to read this chapter referr ing to the front diagrams of
chapter “3. CONTROLS” on page 5 (unfold).
CAUTION
When the unit is turned on, starting and stopping the engine with its volume raised to the
maximum level may harm your hearings. Be
careful about adjusting the volume.
Note:
• Use this unit after starting the engine.
Turning on and off the power
Note:
• Be careful about using this unit for a long time without running the engine. If you drain the car’s battery too far, you may not be able to start the engine and this can reduce the service life of the
battery.
1. Press the POWER button 1.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
3.
Press and hold the POWER button 1 f or 1 second or longer to turn off the power for the unit.
Note:
• About the “SYSTEM CHECK”
The confirmation of connected equipment must be
performed for this unit only when the wiring connection is complete and power is turned on to the
unit first. When the power is supplied, “SYSTEM ”
and “PUSH PWR” appear alternately in the display. Press the POWER button
1
, the system
check starts inside the unit. When “COMPLETE”
appears, press once again the POWER b utton
1
.
Selecting a mode
1. Press the FNC button 1 to change the mode
of operation.
2. Each time you press the FNC button 1, the
mode of operation changes in the following
order:
Radio mode ➜ DAB mode ➜ CD changer
mode ➜ MD changer mode ➜ DVD changer
mode ➜ TV mode ➜ Radio mode...
∗ External equipment not connected with CeNET
is not selected.
Adjusting the volume
Operate the VOLUME button 2 in the direction
of the arrows
ww
ww
w (up) or
zz
zz
z (down) to adjust the
volume;
ww
ww
w: Increases the volume.
zz
zz
z: Decreases the volume.
∗ The volume level indicated in the display is in a
range from 0 (minimum) to 33 (maximum).
CAUTION
While driving, keep the volume at a level at
which external sounds can be heard.
Switching the display
When the panel is closed:
Press the DISP button @to select the desired display.
Each time you press the DISP button @, the display switches in the following order :
Notes:
• Once selected, the preferred display becomes the
default display. When a function adjustment such
as volume is made, the display momentarily
switches to that function’s display, then returns
back to the preferred display several seconds after the adjustment.
VRX630 15
English
Owner’s manual
Basic Operations
•
If a title has been input, it is shown in the SUB display. If no title has been input, “---------” appears in
the display. To input a title, refer to the subsection
“Entering titles” in “Other Functions” section.
• For CD, MD and TV, some special characters of
the title, will not be displayed on the Information
Panel of the DCP. In this case, those characters
will only be left blank.
Showing a mode display
When the panel is open:
Press the TITLE button ( to show the Title List
display. In the Title List display , the titles of items
stored in the PRESET buttons # 1 to 6 are listed.
∗ For detailed information, refer to the section “Title
list play”.
Opening and turning the display
Notes:
• Do not place any object on the open display.
• Do not drop any object on the movable part.
• Do not expose the display to shocks.
1. Press the OPEN button ! to open the Color
LCD display ¥.
∗ If the Color LCD display ¥ is left horizontally
in the open position for 10 seconds or longer,
it is automatically drawn in.
2. Turn the Color LCD display ¥ upwards to a
good view angle.
When the monitor is turned upwards, a picture appears in the display. The Information
Panel 4 display disappears.
3. T o store the Color LCD display ¥ in the source
unit, turn it to the horizontal position until a
click is heard.
CAUTION
Do not turn the display unless it is completely
open.
When adjusting the angle of the display be
careful no to let your fingers get caught by
the panel or instrument panel of the vehicle.
Turning on and off the monitor
Pressing the DISP button @ turns the monitor
on and off.
∗ When a button is pressed or during security moni-
toring, the monitor-off mode is canceled.
Mute
Each time you press the MUTE button $, mute
is turned on and off.
“MUTE” appears when mute is turned on.
Setting the Z-enhancer
This unit comes with 3 types of sound tone effect
stored in memory. Select the one you prefer.
∗ The factory default setting is “Z-EHCR OFF”.
When a Z-enhancer comes on (1-3), “Z-EHCR”
appears in the display.
•“Z-EHCR 1” (Z-Enhancer 1):
Setting emphasizing bass.
•“Z-EHCR 2” (Z-Enhancer 2):
Setting emphasizing treble.
•“Z-EHCR 3” (Z-Enhancer 3):
Setting emphasizing bass and
treble.
•“Z-EHCR OFF” (Z-Enhancer off):
Neither bass nor treble are empha-
sized by the Z-enhancer.
Note:
• Incapable of operation when connecting DSP
(DPH910).
16 VRX630
English
Owner’s manual
Basic Operations
When the panel is closed:
Each time you press the Z-EHCR button 9, the
tone effect changes in the following order:
“Z-EHCR 1” ➜ “Z-EHCR 2” ➜ “Z-EHCR 3” ➜
“Z-EHCR OFF” ➜ “Z-EHCR 1”...
When the panel is open:
1. Press the A-M button & to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK ¡ upward or downward to select “Z-EHCR”. Press the ENT at
the center of the JO YSTICK ¡ to change into
the Z-enhancer selecting display.
3. Operate the JOYSTICK ¡ upward or downward to select out of:
“TYPE 1” (Z-Enhancer 1)
“TYPE 2” (Z-En-
hancer 2)
“TYPE 3” (Z-Enhancer 3)
“OFF” (Z-Enhancer off),
and press the ENT at the center of the JOY-
STICK ¡ to set a desired Z-enhancer.
4. When the setting is finished, operate the JOYSTICK ¡ rightward or leftward to move the
cursor to the “MENU”. Then press the ENT at
the center of the JOYSTICK ¡ to return to
the AUDIO-MODE display.
∗
T o return from the A UDIO-MODE display to the
STANDARD display, press the A-M button
&
once again.
Adjusting the Z-enhancer
Note:
• This function is enabled only when the panel is
open.
1. Press the A-M button & to change into the
AUDIO-MODE display.
2.
Operate the JOYSTICK ¡
upward or downward
to select “Z-EH L VL” level. Press
the ENT at the
center of the JO YSTICK ¡
to change into the
Z-enhancer adjusting
display
.
3. Operate the
JOYSTICK
¡ upward or down-
ward to adjust the Z-enhancer level.
∗ When Z-Enhancer 1 is selected, you can adjust
the bass in the range of ±2.
∗ When Z-Enhancer 2 is selected, you can adjust
the treble in the range of ±2.
∗ When Z-Enhancer 3 is selected, you can adjust
the bass and treble in the range of ±2.
4. When the adjustment is finished, operate the
JOYSTICK ¡ rightward or leftward to mov e
the cursor to “MENU”. Then press the ENT at
the center of the JOYSTICK ¡ to return to
the AUDIO-MODE display.
Adjusting the bass and treble
Notes:
• This function is enabled only when the panel is
open.
• This function can be adjusted only when the Zenhancer is OFF.
1. Press the A-M button & to change into the
A UDIO-MODE display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select “BAS/TRE”. Then press the
ENT at the center of the JOYSTICK ¡ to
change into the BASS/TREBLE adjusting display.
3. Operate the JOYSTICK ¡ r ightward or left-
ward to adjust the “BASS” or “TREBLE”.
4. Operate the JOYSTICK ¡ upward or down-
ward to adjust a lev el (adjustment range: from
-6 to 6).
5. When the adjustment is finished, operate the
JOYSTICK ¡ r ightward or leftward to move
the cursor to “MENU”. Then press the ENT at
the center of the JOYSTICK ¡ to return to
the AUDIO-MODE display.
Adjusting the balance and fader
Note:
• This function is enabled only when the panel is
open.
1. Press the A-M button & to change into the
A UDIO-MODE display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select “BAL/FAD”. Then press the
ENT at the center of the JOYSTICK ¡ to
change into the BAL/FAD adjusting display.
3. Operate the JOYSTICK ¡ r ightward or left-
ward to select “BALANCE” or “FADER”.
4.
Operate the JOYSTICK ¡ upward or downward to make an adjustment.
Adjusting range of the balance: L13 to R13
Adjusting range of the fader: front 12 / rear 12
5. When the adjustment is finished, operate the
JOYSTICK ¡ r ightward or leftward to move
the cursor to “MENU”. Then press the ENT at
the center of the JOYSTICK ¡ to return to
the AUDIO-MODE display.
Loading...