Clarion PN-3124N-A, PN-3124N-B Service Manual

Clarion Co., Ltd.

7-2, Shintoshin, Chuo-ku, Saitama-shi, Saitama 330-0081 Japan

Service Dept.: 7-2, Shintoshin, Chuo-ku, Saitama-shi, Saitama 330-0081 Japan

Tel: [phone] FAX: [phone]

Service Manual

NISSAN Automobile Genuine
6CD LW/MW/FM/RDS Bluetooth
Combination

Published by Service Dept.

298-6547-00

Printed in P.R.C

Mar.2008 X

NOTES

* As for this model, the tuner of the DSP type is used.

When you exchange it due to the tuner pack(BL101;880­2091M) trouble, it is necessary to adjust for S-meter etc.
Special JIG is necessary for an accurate adjustment. The
procedure document for the exclusive use jig is appended
to it.

* This system controller IC M30876FJBGP(IC402) of Main

PWB does not have program. Please use special JIG at
the time of IC ex-change to write the memory.

* This DSP IC SAF7730HV/N317(IC301) of Main PWB is

exposed die soldering pad type. It cannot remove in an
ordinary soldering iron.
Please use special removal JIG at the time of IC ex­change

* The word mark and logos are owned by the

Bluetooth SIG, Inc. and any use of suchmarks by
CLARION CO.,LTD. is under license.

* We cannot supply PWB with component parts in prin-

ciple. When a circuit on PWB has failure, please repair it
by component parts base. Parts which are not mentioned
in service manual are not supplied.

* Specifications and design are subject to change without

notice for further improvement.

SPECIFICATIONS

Radio section

Tuning system: PLL Fr e q ueency synthesi zer sys -

tem

Model

Model

Receive range: LW 153kHz to 279kHz

Intermediate frequency:

Quieting sensitivity: LW Less than 45dBu

Separation: FM 22+5/-7dB(1kHz)
S/N ratio: LW More than 40dB

Auto tuning stop sensitivity:

PN-3124N-A

(Genuine No.28184 EB46A)

PN-3124N-B

(Genuine No.28184 EB46B)

MW 531kHz to 1,602kHz
FM 87.5MHz to 108.0MHz

LW/MW/FM

10.7MHz

(at 20dB S/N)

MW Less than 37dBu

(at 20dB S/N)

FM Less than 15dBu

(at 30dB S/N)

MW More than 40dB
FM More than 50dB

LW/MW

47+6/-6dBu

FM 29+6/-6dBu

CD section

Disc: 12cm disc
Separation: More than 50dB

(20kHz L.P.F)
S/N ratio: More than 74dB(20kHz L.P.F. JIS-A)
Distortion: Less than 0.2%(20kHz L.P.F.)

General

Load impedance: 4ohm/CH
Power output: 40W x4
Power supply voltage: DC13.2V(10.8 to 15.6V)

Negative ground
Back-up consumption: Less than 0.5mA
Dimensions(mm): 178(W) x 100(H) x 164(D)
Weight: 2.3kg

-1-

PN-3124N

To engineers in charge of repair or

inspection of our products.

Before repair or inspection, make sure to follow the

instructions so that customers and Engineers in charge

of repair or inspection can avoid suffering any risk or

injury.

1. Use specified parts.

The system uses parts with special safety features against fire

and voltage. Use only parts with equivalent characteristics

when replacing them.

The use of unspecified parts shall be regarded as remodeling

for which we shall not be liable. The onus of product liability

(PL) shall not be our responsibility in cases where an accident

or failure is as a result of unspecified parts being used.

2. Place the parts and wiring back in their original positions after

replacement or re-wiring.

For proper circuit construction, use of insulation tubes, bond-

ing, gaps to PWB, etc, is involved. The wiring connection and

routing to the PWB are specially planned using clamps to keep

away from heated and high voltage parts. Ensure that they are

placed back in their original positions after repair or inspec-

tion.

If extended damage is caused due to negligence during re-

pair, the legal responsibility shall be with the repairing com-

pany.

3. Check for safety after repair.

Check that the screws, parts and wires are put back securely

in their original position after repair. Ensure for safety reasons

there is no possibility of secondary ploblems around the re-

paired spots.

If extended damage is caused due to negligence of repair, the

legal responsibility shall be with the repairing company.

4. Caution in removal and making wiring connection to the parts

for the automobile.

Disconnect the battery terminal after turning the ignition key

off. If wrong wiring connections are made with the battery con-

nected, a short circuit and/or fire may occur. If extensive dam-

age is caused due to negligence of repair, the legal responsi-

bility shall be with the repairing company.

5. Cautions in soldering

Please do not spread liquid flux in soldering.

Please do not wash the soldering point after soldering.

6. Cautions in soldering for chip capacitors

Please solder the chip capacitors after pre-heating for replace-

ment because they are very weak to heat.

Please do not heat the chip capacitors with a soldering iron

directly.

7. Cautions in handling for chip parts.

Do not reuse removed chips even when no abnormality is ob-

served in their appearance. Always replace them with new

ones. (The chip parts include resistors, capacitors, diodes, tran-

sistors, etc).

Please make an operation test after replacement.

8. Cautions in handling flexible PWB

Before working with a soldering iron, make sure that the iron

tip temperature is around 270

iron tip repeatedly(more than three times)to the same patterns.

Also take care not to apply the tip with force.

9. Turn the unit OFF during disassembly and parts replacement.

Recheck all work before you apply power to the unit.

. Take care not to apply the

10. Cautions in checking that the optical pickup lights up.

The laser is focused on the disc reflection surface through the

lens of the optical pickup. When checking that the laser opti-

cal diode lights up, keep your eyes more than 30cms away

from the lens. Prolonged viewing of the laser within 30cms

may damage your eyesight.

11. Cautions in handling the optical pickup

The laser diode of the optical pickup can be damaged by elec-

trostatic charge caused by your clothes and body. Make sure

to avoid electrostatic charges on your clothes or body, or dis-

charge static electricity before handling the optical pickup.

11-1. Laser diode

The laser diode terminals are shorted for transportation in or-

der to prevent electrostatic damage. After replacement, open

the shorted circuit. When removing the pickup from the mecha-

nism, short the terminals by soldering them to prevent this

damage.

11-2. Actuator

The actuator has a powerful magnetic circuit. If a magnetic

material is put close to it. Its characteristics will change. En-

sure that no foreign substances enter through the ventilation

slots in the cover.

11-3. Cleaning the lens

Dust on the optical lens affects performance.

To clean the lens, apply a small amount of isopropyl alcohol to

lens paper and wipe the lens gently.

COMPONENT

PN-3124N-A/B

1. Main unit ---------- 1

CAUTION

This appliance contains a laser system and is classified as
a "CLASS 1 LASER PRODUCT".To use this model
properly,read this Owner's Manual carefully and keep this
manual for your future reference.In case of any trouble with
this player,please contact your nearest "AUTHORIZED ser­vice station".To prevent direct exposure to the laser beam,do
not to open the enclosure.

NISSAN PART No.

MODEL NO.

N DE MODELE

TENSION D UTILISATION 12V AUCHASSIS

SERIAL No.

TYPE

DESIGN NOTE No.

Bluetooth ID

Clarion co., Ltd
MADE IN
PART NO.

276-

PN-3124N

-2-

EXPLANATION OF IC

051-3516-90 S-1132B33-U5T1G

Vout

Ground

No Connectin

Positive Voltage Regurator 3.3V

1

54Vin

2

3

Ground

Control (H= On)

051-3518-90 NJM2846DL3-33-TE1

Positive Voltage Regurator 3.3V

5

3

4

3

2

1

N.C

Power Outut

Ground

VCC

Control in, H = O N.

051-3517-90 impossible of exchange (LT3481EMSE#TRPBF)

Step-Down Switching Regulator

TOP VIEW

RT

BD

1

BOOST

RUN/SS

SW

VIN

2

3

11

4

5

Terminal Description

BD (Pin 1):

This pin connects to the anode of the boost Schottky diode.

BOOST (Pin 2):

This pin is used to provide a drive voltage, higher than the input
voltage, to the internal bipolar NPN power switch.

SW (Pin 3):

The SW pin is the output of the internal power switch. Connect this
pin to the inductor, catch diode and boost capacitor.

VIN (Pin 4):

The VIN pin supplies current to the LT3481's internal regulator and
to the internal power switch. This pin must be locally bypassed.

RUN/SS (Pin 5):

The RUN/SS pin is used to put the LT3481 in shutdown mode. Tie
to ground to shut down the LT3481. Tie to 2.3V or more for nor­mal operation. If the shutdown feature is not used, tie this pin to
the VIN pin.

PG (Pin 6):

The PG pin is the open collector output of an internal comparator.
PG remains low until the FB pin is within 10% of the final regula­tion voltage. PG output is valid when VIN is above 3.5V and RUN/
SS is high.

BIAS (Pin 7):

The BIAS pin supplies the current to the LT3481's internal regula­tor. Tie this pin to the lowest available voltage source above 3V
(typically VOUT). This architecture increases efficiency especially
when the input voltage is much higher than the output.

FB (Pin 8):

The LT3481 regulates the FB pin to 1.265V. Connect the feedback
resistor divider tap to this pin.

VC (Pin 9):

The VC pin is the output of the internal error amplifier. The volt­age on this pin controls the peak switch current. Tie an RC net­work from this pin to ground to compensate the control loop.

RT (Pin 10):

Oscillator Resistor Input. Connecting a resistor to ground from this
pin sets the switching frequency.

Exposed Pad (Pin 11):

Ground. The Exposed Pad must be soldered to PCB.

10

9

8

7

6

VC

FB

BIAS

PG

051-3519-90 NJU7771F05-TE2

Positive Voltage Regurator 5.0V

1

Control (H= On)

Ground

N.C.

54Vin

2

3

Vout

051-9425-80 S-24CS64A0I-J8T1G EEP-ROM

A0

1

A1

2

A2

3

GND

4

Terminal Description

pin 1: A 0 : IN : Address input.

pin 2: A 1 : IN : Address input.

pin 3: A 2 : IN : Address input.

pin 4: GND : - : Ground.

pin 5: S DA :I/O: Serial data input/output.

pin 6: S CK :IN : Serial clock pulse input.

pin 7: Write Protect : IN: Write protect signal input.

H = protect ON.

pin 8: VCC : - : Positive voltage supply.

VCC

8

WP

7

SCL

6

SDA

5

052-0320-00 M30876FJBGP System Contoller

[ Note ] The program is not written in this IC. Therefore, you need to

write a program in this IC with the part exchange.

Terminal Description

pin 1: NU : IN : Not in use.

pin 2: Speed Pulse : IN : Speed pulse input.

pin 3: IMMOBI TX : O : Serial data output for IMMOBI.

pin 4: IMMOBI RX : IN : Serial data input for IMMOBI.

pin 5: BU DET : IN : Backup detection signal input.

pin 6: GND : - : Ground.

pin 7: CN VSS : IN : Connect to VSS via a resistor.

pin 8: ILL ON : IN : Illumination ON signal input.

pin 9: SYS ON : O : System ON signal output.

pin 10: RESET : IN : Reset signal input.

pin 11: X ou t : O : Crystal connection.

pin 12: VSS : - : Negative voltage supply.

pin 13: X i n : IN : Crystal connection.

pin 14: VDD : - : Positive voltage supply.

pin 15: NMI : IN : Nonmaskable interrupt. Connect to VDD

via a resistor.

-3-

PN-3124N

pin 16 : ACC IN : IN : ACC ON flag input.

pin 17: PLL DO : O : PLL serial data output.

pin 18 : NU : - : Not in use.

pin 19: B/T CTS : IN : BT module UART flow control.

pin 20: B/T RX : IN : BT module UART data input.

pin 21: TIME BASE :IN : Time base pulse input.

pin 22: B/T TX : O : BT module UART data output.

pin 23: PLL CE : O : PLL chip enable signal output.

pin 24: DIMMER : O : Dimmer output.

pin 25: PLL CK : O : PLL clock pulse output.

pin 26 : NU : - : Not in use.

pin 27 : DSP SCL : O : Clock pulse output to the DSP IC.

pin 28: DSP SDA :I/O: Serial data input/output for the digital sig-

nal processor.

pin 29 : NDS TX : O : Serial data output for NDS.

pin 30 : NDS RX : IN : Serial data input for NDS.

pin 31: NDS REQ 1 :IN : NDS request signal input.

pin 32: 6CD SLOT : O : Shutter light control signal output.

pin 33: 6CD SDA :I/O: Serial data input/output.

pin 34: 6CD SCL : O : Serial clock output.

pin 35 : NU : - : Not in use.

pin 36 : NU : - : Not in use.

pin 37: 6CD RESET : O : Reset pulse output.

pin 38 : NU : - : Not in use.

pin 39 : 6-CD REQ : IN : Request signal input for the 6CD-Chang-

er.

pin 40 : NU : - : Not in use.

pin 41 : NU : - : Not in use.

pin 42:NU :IN:Not in use.

pin 43:NU :IN:Not in use.

pin 44:NU :IN:Not in use.

pin 45:NU :IN:Not in use.

pin 46 : NU : - : Not in use.

pin 47 : NU : - : Not in use.

pin 48: CD ON : O : CD ON signal output.

pin 49 : NU : - : Not in use.

pin 50: Pow e r IC Stndb : O : The standby signal output to the power IC.

pin 51: LCD DO : O : Serial data output to the LCD controller.

pin 52 : LCD CK : O : Clock pulse output to the LCD driver.

pin 53 : LCD DI : IN : Serial data input from the LCD driver.

pin 54: LCD CE : O : Chip enable signal output to the LCD driv-

er.

pin 55 : LCD RST : O : Reset pulse output to the LCD driver.

pin 56: VOL 3 : IN : Volume control pulse input from the rota-

ry encoder.

pin 57: VOL 2 : IN : Volume control pulse input from the rota-

ry encoder.

pin 58: VOL 1 : IN : Volume control pulse input from the rota-

ry encoder.

pin 59 : FAN ON : O : The fan on signal output.

pin 60: VDD : - : Positive voltage supply.

pin 61: POWER ON : IN : Power ON signal input.

pin 62: GND : - : Ground.

pin 63: B/T TEST : O : BT module test.

pin 64 : AUX ON :IN : AUX ON signal input.

pin 65: DIAG INPUT : IN: Diagnosis signal input from the audio pow-

er IC.

pin 66 : B/T RTS : O : BT module UART flow control. AUX con-

nection detection.

pin 67: B/T TEST : O : BT module test.

pin 68: B/T BOOTE : O : BT module rewrite.

pin 69 : B/T RESET P : O : BT module reset.

pin 70 : NU : - : Not in use.

pin 71:NU :IN:Not in use.

pin 72 : RD S CL 1 :IN : RDS 1 serial clock output.

pin 73 : RD S DA 1 : IN : RDS 1 serial data input.

pin 74: GIX SYS ACC : O : 6CD-mechanism system ACC control.

pin 75: P IC MUTE : O : Muting-command output for the audio pow-

er IC.

pin 76: MH MUTE : O : Muting-command output for RDS and

DSP.

pin 77 : M AGC BUFF : IN : DSP Keyed AGC detection.

pin 78 : DSP RESET : O : Reset signal output to the DSP IC.

pin 79: MT S METER : IN : Input of internal A/D converter to monitor

the radio field strength for the Main-tun­er.

pin 80: MT SAMPLE : IN : Main-tuner sample input.

pin 81: MT HOLD : IN : AF-hold-signal input from the Main-tuner.

And S-hold signal input from the DSP.

pin 82 : NU : IN : Not in use.

pin 83 : NU : IN : Not in use.

pin 84 : NU : IN : Not in use.

pin 85 : NU : IN : Not in use.

pin 86 : NU : IN : Not in use.

pin 87: CD EJECT : IN : CD eject signal input.

pin 88: LOAD SW : IN : LOAD switch signal input.

pin 89 : NU : - : Not in use.

pin 90 : NU : - : Not in use.

pin 91: INI KEY : IN: Initializing command input.

pin 92: REMO A : IN : Steering wheel remote controller signal

input.

pin 93: REMO B : IN : Steering wheel remote controller signal

input.

pin 94: A GND : - : Analog ground.

pin 95 : NU : - : Not in use.

pin 96: VREFI : IN : Reference voltage input.

pin 97: A VCC : - : Positive voltage supply for the internal

analog section.

pin 98: MT SCL : IN : Main-tuner control clock pulse.

pin 99 : MT SDA :I/O: Serial data input/output for the Main-tun-

er.

pin100: DSP PAUSE : IN : DSP automatic mute control. L = mute on.

PN-3124N

-4-

BLOCK DIAGRAM

ANT101

GT13

ANT-ON

ANT

BL101

AM/FM

TUNER

E2 PROM

TUNER9V

Q110,111

ANT-ON

+B

( PN-3124N-A )

CD

MECHANISM

SWITCH PWB

LCD

1/8DUTY

5x7 DOTx13

TUNER5V

SYS5V

6CD-9V6CD-3.3V

GUIDE ILL

ILL+

ILL-

LCD DRIVER

LC75816

IC801

SYS5V

SYS9V

IF

Digital

EEPROM

IC406

RESET

IC404

CD-EJ

6CD-LOAD

KEY

CERAMIC-ANT

ANT902

SYS-1.8V

REG

Q301

DSP

SAF7730

IC301

AUDIO-CPU

M30876FJBGP

IC402

DSP-3.3V

VOLUME
BASS
TREBLE
BALANCE
FADER

EQ
RDS

AM NC
SOUND FOUCUS

UGZZ5

IC901

CODEC-IC㵘AK2301A

IC101

20K LPF

IC501

SYS 9V

1/2SYS 9V

SSV

BT 3.3V

IC502

DSP-3.3V

IC504

CD 3.3V

IC205

CONTROL

TUNER 5V

IC104

SYS 5V

Q518,519

TUNER 9V

1/2SYS 9V

AUDIO-SIG

MIC AUDIO

Q219,Q220

IMMOBI I/F

Q109

CD 9V
IC204

BL+9V,DIMMER

Q506,507,509

ACC-DET Q520

REMOCOM

I/F

MIC+B

POWER IC
40W x 4CH

4 ohm

TA8275

IC503

VDD 5V

REG IC505

SYS 12V

Q516,517

SYS 9V

Q515

ILL

POWER-SUPPLY

B/U
FIL

POWER

-SUPPLY

MIC SIGNAL
MIC GND

MIC VCC

FR-L +
FR-L ­FR-R +
FR-R ­RR-L +
RR-L ­RR-R +
RR-R -

SPEED SIGNAL
IMMOBILIZER

BACK UP

GND
STRG GND

ACC

ILLUMI +

STRG SW A
STRG SW B

J201

NAVI Connector

(TH12 HW)

J502

Main Connector

(TH18 )

CONNECTOR LAYOUT

ANT101

ANT Connector

(GT13)

A

B

C

A

ANTENNA ON

ACTIVE ANT

B

: USED ANTENNA BOOST

AMP TYPE

( PN-3124N-A)

PASSIVE ANT

( PN-3124N-B)

N.C.

C

ANT101

Rear view of the unit

J201

J201

NAVI Connector

(TH12 HW)

1

2

34

5

78

1

N.C.

2

N.C.

3

N.C.

4

N.C.

5

N.C.

6

N.C.

10

9

MIC SIGNAL

7

8

MIC GND

9

MIC VCC

10

N.C.

N.C.

11

N.C.

12

11

J502

J502

Main Connector

(TH18 )

2

3456789

6

12

1
2

3

4

5

6

7
8
9

10

1

19

1112131415 16 17 18

10

N.C.
FRONT-LH(+)

FRONT-LH(-)
REAR-LH(+)
REAR-LH(-)

STRG SW A

ACC

N.C.
ILLUMI (+)

N.C.

11

FRONT-RH(+)
FRONT-RH(-)

12

REAR-RH(+)

13

REAR-RH(-)

14

STRG GND

15

STRG SW B

16

IMMOBILIZER

17

SPEED SIGNAL

18

19

BACK UP

20

GND

20

-5-

PN-3124N

TROUBLESHOOTING

No power

Check

B/U, ACC

OK

Check

the display

OK

Check

the operating key

OK

Problem of
IC402, IC404, IC406, IC506

Power on

No sound radio

Check

the display

OK

Check

the operating key

OK

Check

the voltage value of

TUNER8.5V/TUNER5V

OK

Check

the waveform of

16,17pin of BL101

Confirm to
circuit line of B/U5V, ACC,

NG

SYS5V
the voltage value of
IC505, Q520, Q519

Confirm to

NG

the voltage value of
Q515, IC801

NG

Problem of IC801

Confirm to

NG

the voltage value of
Q515, IC801

NG

Problem of IC801

NG

Problem of Q109, IC104

NG

Problem of BL101

Power on

No sound CD

Check

the display

OK

Check

the operating key

OK

Check

the voltage value of

CD9V/CD5V

/CD3.3V

OK

Check

the waveform of

8pin of J202

OK

Check

the waveform of

38,39,43,44pin of

IC301

OK

Check

the waveform of

IC501

OK

Check

the waveform of

IC503

OK

Connection J502

Confirm to

NG

the voltage value of
Q515, IC801

NG

Problem of IC801

NG

Problem of
IC204, IC205

NG

Problem of CD mech

NG

Problem of IC301

NG

Problem of IC501

NG

Problem of IC503

OK

Check

the waveform of

38,39,43,44pin

of IC301

OK

Check

the waveform of

IC501

OK

Check

the waveform of

IC503

OK

Connection J502

NG

Problem of IC301

NG

Problem of IC501

NG

Problem of IC503

PN-3124N

-6-

The cellular phone and Bluetooth
cannot be connected.

Check

enter in a set screen

of the telephone

OK

Check

how to connect by inquiry

from the cellular phone

OK

the link of Bluettoth steady

Check

or

the BT mark on

OK

Confirm to
connect Bluetooth
with the cellular phone again

NG

Check
the power of IC901
(Bluetooth module)

OK

Confirm to
IC901 (Bluetooth module)
the circuit of
Q101,102,104,105,106,107,108

Confirm to
IC901 (Bluetooth module)

NG

the circuit of
Q101,102,104,105,106,107,108
ANT902 (Bluetooth module)

Confirm to

NG

IC901 (Bluetooth module)
the circuit of ANT902
(Bluetooth module)

Confirm to

NG

IC901 (Bluetooth module)
IC502 (the power of 3.3V)

The receiving talk voice
doesn't go out of the speaker.

Check

connect it with

the cellular phone

OK

Check

the sound of

CD or radio

OK

the call sound come to send it

Check

by telephone

OK

Confirm to

NG

IC901 (Bluetooth module)

Confirm to

NG

IC402 (DSP), IC501 (AMP),
IC503 (Power AMP),
J502 (Connector)

Check
the power of IC901
(Bluetooth module)

Check

the power of IC101

(CODEC)

Check

the waveform of

9pin of IC101

OK

Check

the waveform of

43pin of IC402(DSP)

OK

OK

OK

Confirm to

NG

the circuit of
IC502 (the power of 3.3V)

Confirm to

NG

the circuit of
IC502 (the power of 3.3V)

Confirm to
the circuit of

NG

IC101 (CODEC)
IC901 (Bluetooth module)

Confirm to

NG

the circuit of IC402 (DSP)

OK

Confirm to
the output of J502

-7-

PN-3124N

EXPLODED VIEW/PARTS LIST

34

47

10

47

37

16

11

11

49

47

50

15

47

17

39

13

43

32

38

47

47

14

20

18

28

44

32

46

33

36

29

34

22

30

23

38

38

26

32

24

42

38

32

21

19

35

40

41

43

31

34

27

25

38

32

33

48

47

45

5

x9

12

11

6

7

8

9

11

PN-3124N

4

3

2

1

-8-

Note) Some parts depend on each model.The model name is specified in the description.

NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY

1 940-8420-29 ES-ASSY 1 27 074-1302-12 OUTLET SOCKET 1
2 947-0591-00 KNOB ASSY 1 28 331-3880-00 TR HOLDER 1
3 347-7959-00 SHADE 1 29 313-1980-00 HEAT SINK 1
4 380-5655-10 KNOB 1 30 716-1646-50 IT SCREW (M2.6 x 8) 1
5 ----------- SWITCH PWB 1 31 307-0720-00 REAR PLATE 1
6 335-7693-00 LCD HOLDER 1 32 073-0762-90 TERMINAL 5
7 335-7801-00 LCD LEFLECTOR 1 33 778-3006-00 SCREW (3 x 6) 4
8 379-1392-52 INDICATOR (LCD) 1 34 714-2608-8B

MACHINE SCREW (M2.6 x 6)

7

9 331-4166-00 LCD COVER 1 35 3 45-5805-01 GASKET 1
10 016-7004-00 ROTARY SWITCH 1 36 311-1914-00 LOWER CASE 1
11 013-6201-52 TACT SWITCH 15 37 313-1967-00 HEAT SINK 1
12 013-6202-52 TACT SWITCH 9 38 716-0878-50 SCREW (M2.6 x 5) 5
13 074-3013-72 OUTLET SOCKET (22P) 1 39 309-0822-00 ES PLATE (6CD) 1
14 074-3013-66 OUTLET SOCKET (16P) 1 40 929-0390-82 CD MECH MODULE 1
15 345-8090-00 CUSHION RUBBER 1 41 331-4092-10 CD MECH BRKT (RH) 1
16 716-0778-52 WAVE SCREW (2 x 6) 10 42 331-4091-10 CD MECH BRKT (LH) 1
17 716-0872-51 PAD SCREW (M1.7 x 5) 2 43 716-3552-00 SCREW (M2.3 x 2.5) 6
18 345-5805-01 GASKET 1 44 816-4024-50 FLAT WIRE 1
19 ----------- MAIN PWB 1 45 310-1823-10 UPPER CASE 1
20 074-1237-69 OUTLET SOCKET (19P) 1 46 735-2614-1B

MACHINE SCREW (M2.6 x 14)

2

21 076-0478-59 PLUG (9P) 1 47 714-2606-8B

MACHINE SCREW (M2.6 x 6)

10
22 076-3011-72 PLUG (22P) 1 48 276-0034-75 SET PLATE (PN-3124N-A) 1
23 076-3011-66 PLUG (16P) 1 276-0034-76 SET PLATE (PN-3124N-B) 1
24 880-2091M TUNER PACK 1 49 060-8062-50 CERAMIC-ANT 1
25 092-2210-01 ANT RECEPT 1 50 060-8079-90 BLUETOOTH MODULE 1
26 074-4009-20 OUTLET SOCKET 1

-9-

PN-3124N

ELECTRICAL PARTS LIST

Switch PWB(B1) section

REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION

ANT902 060-8062-50 CERAMIC-ANT
C802 168-1042-78 16V 0.1uF
C803 168-1042-78 16V 0.1uF
C804 168-4732-78 0.047uF K
C805 168-4732-78 0.047uF K
C806 168-4732-78 0.047uF K
C807 166-2211-50 220pF CH
C901 168-1042-78 16V 0.1uF
C902 166-1011-50 100pF CH
C903 168-1042-78 16V 0.1uF
C904 166-1011-50 100pF CH
C905 166-1011-50 100pF CH
C906 042-0423-97 16V 10uF
C907 168-1042-78 16V 0.1uF
C908 168-1042-78 16V 0.1uF
C909 178-3312-78 330pF
CCT801 050-0145-52 1/16W 1k ohm x4
D801 001-0529-32 MA8056-M
D802 001-0529-32 MA8056-M
D803 001-0529-32 MA8056-M
D804 001-0529-32 MA8056-M
D805 001-0529-32 MA8056-M
D806 001-7093-91 RFY1112H-16-TR

YEL

D807 001-7093-91 RFY1112H-16-TR

YEL

D808 001-7093-91 RFY1112H-16-TR

YEL

D809 001-7093-91 RFY1112H-16-TR

YEL

D810 001-7093-91 RFY1112H-16-TR

YEL

D811 001-7093-91 RFY1112H-16-TR

YEL

D812 001-7093-91 RFY1112H-16-TR

YEL

D813 001-7093-91 RFY1112H-16-TR

YEL

D814 001-7093-91 RFY1112H-16-TR

YEL

D815 001-7093-91 RFY1112H-16-TR

YEL

D816 001-7093-91 RFY1112H-16-TR

YEL

D817 001-7093-91 RFY1112H-16-TR

YEL

D818 001-7093-91 RFY1112H-16-TR

YEL

D819 001-7093-91 RFY1112H-16-TR

YEL

D820 001-7093-91 RFY1112H-16-TR

YEL

D821 001-7093-91 RFY1112H-16-TR

YEL

D822 001-7093-91 RFY1112H-16-TR

YEL

D823 001-7093-91 RFY1112H-16-TR

YEL

D824 001-7093-91 RFY1112H-16-TR

YEL

D830 001-7093-91 RFY1112H-16-TR

YEL

D831 001-7093-91 RFY1112H-16-TR

YEL

D832 001-7093-91 RFY1112H-16-TR

YEL

D833 001-7093-91 RFY1112H-16-TR

YEL

D834 001-7093-91 RFY1112H-16-TR

YEL

D835 001-7093-91 RFY1112H-16-TR

YEL

D836 001-7093-91 RFY1112H-16-TR

YEL

D837 001-7093-91 RFY1112H-16-TR

YEL

D838 001-7093-91 RFY1112H-16-TR

YEL

D839 001-7093-91 RFY1112H-16-TR

YEL

D846 001-7093-91 RFY1112H-16-TR

YEL

D847 001-7093-91 RFY1112H-16-TR

YEL

D848 001-7093-91 RFY1112H-16-TR

YEL

D849 001-7093-91 RFY1112H-16-TR

YEL

D850 001-7093-91 RFY1112H-16-TR

YEL

D851 001-7093-91 RFY1112H-16-TR

YEL

D852 001-7093-91 RFY1112H-16-TR

YEL

D853 001-7093-91 RFY1112H-16-TR

YEL

D855 001-7093-91 RFY1112H-16-TR

YEL

D856 001-7093-91 RFY1112H-16-TR

YEL

D857 001-7093-91 RFY1112H-16-TR

YEL

D858 001-7093-91 RFY1112H-16-TR

YEL

D859 001-7093-91 RFY1112H-16-TR

YEL

D860 001-7093-91 RFY1112H-16-TR

YEL

D861 001-7093-91 RFY1112H-16-TR

YEL

D862 001-7093-91 RFY1112H-16-TR

YEL

D864 001-7093-91 RFY1112H-16-TR

YEL

D865 001-7093-91 RFY1112H-16-TR

YEL

D866 001-7093-91 RFY1112H-16-TR

YEL

D867 001-7093-91 RFY1112H-16-TR

YEL

D869 001-7093-91 RFY1112H-16-TR

YEL

D870 001-7093-91 RFY1112H-16-TR

YEL
IC801 051-6075-00 LC75816W-8722-E
IC901 060-8079-90 UGZZ5-601D
J801 074-3013-72 22P
J901 074-3013-66 16P
LCD801 379-1392-52 INDICATOR (LCD)
L901 010-3104-54 600 ohm/100MHz
L902 010-3104-54 600 ohm/100MHz
L903 010-3104-54 600 ohm/100MHz
L904 010-3104-54 600 ohm/100MHz
L906 010-3104-54 600 ohm/100MHz
L907 010-3104-54 600 ohm/100MHz
L909 010-3104-54 600 ohm/100MHz
L910 010-3104-54 600 ohm/100MHz
L911 010-3104-54 600 ohm/100MHz
L912 010-3104-54 600 ohm/100MHz
R801 119-0000-05 1/10W 0 ohm JW

R802 119-3331-15 1/10W 33k ohm
R803 119-1021-15 1/10W 1k ohm
R804 116-3321-15 1/4W 3.3k ohm
R805 116-3321-15 1/4W 3.3k ohm
R806 116-3321-15 1/4W 3.3k ohm
R807 116-3321-15 1/4W 3.3k ohm
R808 116-3321-15 1/4W 3.3k ohm
R809 116-3921-15 1/4W 3.9k ohm
R810 116-2421-15 1/4W 2.4k ohm
R811 116-4721-15 1/4W 4.7k ohm
R812 116-4721-15 1/4W 4.7k ohm
R813 116-4721-15 1/4W 4.7k ohm
R814 116-4721-15 1/4W 4.7k ohm
R815 116-2221-15 1/4W 2.2k ohm
R816 116-2221-15 1/4W 2.2k ohm
R817 119-1521-15 1/10W 1.5k ohm
R819 116-3321-15 1/4W 3.3k ohm
R822 119-2421-15 1/10W 2.4k ohm
R823 116-4721-15 1/4W 4.7k ohm
R824 119-2421-15 1/10W 2.4k ohm
R825 116-4721-15 1/4W 4.7k ohm
R826 119-2421-15 1/10W 2.4k ohm
R827 116-3921-15 1/4W 3.9k ohm
R828 119-2421-15 1/10W 2.4k ohm
R829 116-2421-15 1/4W 2.4k ohm
R830 119-2421-15 1/10W 2.4k ohm
R831 116-4721-15 1/4W 4.7k ohm
R832 119-2421-15 1/10W 2.4k ohm
R833 119-1521-15 1/10W 1.5k ohm
R905 119-2711-15 1/10W 270 ohm
R909 119-1031-15 1/10W 10k ohm
R914 119-5631-15 1/10W 56k ohm
R916 119-1821-15 1/10W 1.8k ohm
R917 119-2711-15 1/10W 270 ohm
R918 119-1011-15 1/10W 100 ohm
R919 119-1011-15 1/10W 100 ohm
S801 016-7004-00 ROTARY SWITCH
S802 013-6201-52 SKPMAP010
S803 013-6202-52 SKPMBJE010
S804 013-6202-52 SKPMBJE010
S807 013-6202-52 SKPMBJE010
S808 013-6201-52 SKPMAP010
S809 013-6201-52 SKPMAP010
S810 013-6202-52 SKPMBJE010
S811 013-6202-52 SKPMBJE010
S812 013-6202-52 SKPMBJE010
S813 013-6201-52 SKPMAP010
S814 013-6201-52 SKPMAP010
S815 013-6202-52 SKPMBJE010
S816 013-6202-52 SKPMBJE010
S818 013-6201-52 SKPMAP010
S819 013-6201-52 SKPMAP010
S820 013-6201-52 SKPMAP010
S821 013-6202-52 SKPMBJE010
S822 013-6201-52 SKPMAP010
S823 013-6201-52 SKPMAP010
S824 013-6201-52 SKPMAP010
S825 013-6201-52 SKPMAP010
S826 013-6201-52 SKPMAP010
S827 013-6201-52 SKPMAP010
S828 013-6201-52 SKPMAP010
TM901 073-0778-90 TERMINAL
TM902 073-0778-90 TERMINAL
TM903 073-0778-90 TERMINAL
TM904 073-0778-90 TERMINAL
PWB 039-2925-01 PWB(WITHOUT

COMPONENT)

PN-3124N

-10-

Main PWB(B2) section

REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
ANT101 092-2210-01 ANTENNA RECEPT C315 168-1022-55 1000pF K C533 168-5632-78 16V 0.056uF
BL101 880-2091M FM/AM TUNER C316 168-1022-55 1000pF K C534 168-5632-78 16V 0.056uF
C104 168-2222-55 2200pF K C317 166-1011-50 100pF CH C535 168-5632-78 16V 0.056uF

(PN-3124N-A) C318 168-1042-78 16V 0.1uF C536 168-5632-78 16V 0.056uF

C108 166-1511-50 150pF CH C319 168-5622-55 5600pF K C537 178-1052-78 1uF

(PN-3124N-A) C320 168-5622-55 5600pF K C540 163-1063-35 16V 10uF

C108 119-0000-05 1/10W 0 ohm JW C323 168-1022-55 1000pF K C541 168-1522-55 1500pF K

(PN-3124N-B) C324 163-2273-05 4V 220uF C546 168-1042-78 16V 0.1uF
C109 166-2201-50 22pF CH C325 168-2222-55 2200pF K C547 178-1052-78 1uF
C110 168-1042-78 16V 0.1uF C326 166-4711-50 470pF CH C549 163-2273-25 10V 220uF
C111 178-3342-78 0.33uF C327 163-2263-35 16V 22uF C550 178-4742-78 0.47uF
C112 163-4763-15 6.3V 47uF C328 168-1022-55 1000pF K C551 168-1042-38 50V 0.1uF
C113 178-1052-78 1uF C329 166-1007-50 10pF CH C552 163-4763-35 16V 47uF
C114 178-1052-78 1uF C330 163-1063-35 16V 10uF C553 163-4763-35 16V 47uF
C115 119-0000-05 1/10W 0 ohm JW C331 166-1011-50 100pF CH C554 189-3383-31 16V 3300uF
C116 168-1222-55 1200pF K C333 168-1042-78 16V 0.1uF C556 172-1041-15 0.1uF
C117 178-1052-78 1uF C334 163-4763-15 6.3V 47uF C557 163-4763-35 16V 47uF
C118 168-4732-78 0.047uF K C335 178-1052-78 1uF C559 168-6822-55 6800pF K
C119 168-1022-55 1000pF K C336 168-3332-78 0.033uF K C560 168-6822-55 6800pF K
C120 168-4722-55 4700pF K C338 168-1022-55 1000pF K C561 168-6822-55 6800pF K
C121 168-4722-55 4700pF K C339 168-1022-55 1000pF K C562 168-6822-55 6800pF K
C122 163-1073-35 16V 100uF C340 166-1007-50 10pF CH C563 168-6822-55 6800pF K
C123 168-2222-55 2200pF K C341 168-4712-55 470pF K C564 166-2201-50 22pF CH
C124 168-1022-55 1000pF K C342 168-1042-78 16V 0.1uF C565 168-6822-55 6800pF K
C125 168-2232-55 0.022uF K C343 168-1022-55 1000pF K C566 168-6822-55 6800pF K
C126 168-2232-55 0.022uF K C345 168-3322-55 3300pF K C567 043-0604-90 25V 10uF B
C127 168-1022-55 1000pF K C346 168-3322-55 3300pF K C568 168-6822-55 6800pF K
C128 168-1022-55 1000pF K C347 168-3322-55 3300pF K C569 168-6822-55 6800pF K
C129 178-1052-78 1uF C348 168-3322-55 3300pF K C571 043-0566-90 50V 2.2uF K
C130 168-1022-55 1000pF K C350 042-0643-58 6.3V 330uF C572 178-1052-78 1uF
C131 163-1073-35 16V 100uF C351 168-4722-55 4700pF K C573 168-1042-78 16V 0.1uF
C132 166-2201-50 22pF CH C352 168-2222-55 2200pF K C574 163-1063-35 16V 10uF
C133 166-2201-50 22pF CH C353 168-2222-55 2200pF K C575 168-2232-55 0.022uF K
C134 166-2201-50 22pF CH C354 168-2222-55 2200pF K C576 163-1073-35 16V 100uF
C135 166-2201-50 22pF CH C355 168-2222-55 2200pF K C577 168-2212-55 220pF K
C136 178-1052-78 1uF C356 163-1073-15 6.3V 100uF C578 119-0000-05 1/10W 0 ohm JW
C137 178-1052-78 1uF C359 168-1022-55 1000pF K CCT401 050-0145-52 1/16W 1k ohm x4
C138 178-3342-78 0.33uF C360 166-4711-50 470pF CH CCT402 050-0145-52 1/16W 1k ohm x4
C140 163-1063-35 16V 10uF C361 043-0554-90 25V 10uF CCT403 050-0145-52 1/16W 1k ohm x4
C141 163-1063-35 16V 10uF C401 168-1042-78 16V 0.1uF CCT402 050-0145-52 1/16W 1k ohm x4

(PN-3124N-A) C402 168-1042-78 16V 0.1uF D106 001-0580-90 1SS352
C142 168-1042-78 16V 0.1uF C404 166-5096-50 5pF CH D108 001-0529-48 MA8091-H
C143 166-6801-50 68pF CH C406 166-5096-50 5pF CH D109 001-0580-90 1SS352
C144 043-0548-50 2.2uF C407 168-1042-78 16V 0.1uF (PN-3124N-A)
C201 043-0548-50 2.2uF C408 163-4763-15 6.3V 47uF D208 001-0580-90 1SS352
C202 043-0548-50 2.2uF C409 168-1042-78 16V 0.1uF D210 001-0529-72 MA8200-M
C203 043-0548-50 2.2uF C412 168-1032-55 0.01uF K D211 001-9210-50 AVR­C204 043-0548-50 2.2uF C413 163-1073-35 16V 100uF M1608C270MTAAD
C220 163-3373-15 6.3V 330uF C501 168-1042-78 16V 0.1uF D212 001-9210-50 AVR­C227 042-0643-58 6.3V 330uF C502 168-1042-78 16V 0.1uF M1608C270MTAAD
C228 163-2273-25 10V 220uF C503 168-1042-78 16V 0.1uF D213 001-9210-50 AVR­C229 163-1063-35 16V 10uF C504 168-1042-78 16V 0.1uF M1608C270MTAAD
C230 168-1042-78 16V 0.1uF C505 166-5611-50 560pF CH D214 001-9210-50 AVR­C232 163-1063-35 16V 10uF C506 166-5611-50 560pF CH M1608C270MTAAD
C233 168-1042-78 16V 0.1uF C507 166-5611-50 560pF CH D215 001-2412-90 RR264M-400
C236 178-1052-78 1uF C508 166-5611-50 560pF CH D505 001-0529-48 MA8091-H
C238 178-3342-78 0.33uF C509 166-2201-50 22pF CH D506 001-2640-90 D1FJ4
C241 168-1022-55 1000pF K C510 166-2201-50 22pF CH D508 001-0529-48 MA8091-H
C242 168-1022-55 1000pF K C511 043-0554-90 25V 10uF D510 001-2015-00 RL253
C301 163-4753-65 50V 4.7uF C512 178-3342-78 0.33uF D511 001-0580-90 1SS352
C302 168-1042-78 16V 0.1uF C513 166-2201-50 22pF CH D512 001-0529-48 MA8091-H
C303 166-1811-50 180pF CH C514 166-2201-50 22pF CH D514 001-0580-90 1SS352
C304 166-1007-50 10pF CH C516 166-5611-50 560pF CH D515 001-0529-34 MA8062-L
C306 168-1042-78 16V 0.1uF C517 166-5611-50 560pF CH D516 001-0580-90 1SS352
C307 168-1042-78 16V 0.1uF C519 166-5611-50 560pF CH D567 001-0580-90 1SS352
C308 166-8097-50 8pF C CH C520 166-5611-50 560pF CH D568 001-0580-90 1SS352
C309 166-8097-50 8pF C CH C521 168-1042-78 16V 0.1uF D569 001-4301-68 HZU18B1
C310 168-1022-55 1000pF K C522 178-3342-78 0.33uF D570 001-4301-68 HZU18B1
C311 163-4753-65 50V 4.7uF C523 163-1063-35 16V 10uF D571 001-4301-68 HZU18B1
C312 168-1042-78 16V 0.1uF C525 163-1073-35 16V 100uF IC101 051-6524-90 AK2301A-E1
C313 163-4753-65 50V 4.7uF C530 163-1073-35 16V 100uF IC103 051-3034-90 NJM4558V
C314 168-1042-78 16V 0.1uF C532 168-1042-78 16V 0.1uF IC104 051-3519-90 NJU7771F05-TE2

Note) Some parts depend on each model. The model name is specified in the description.

-11-

PN-3124N

REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
IC107 051-7255-08 SN74AHC1G66 Q403 191-0709-00 2SB709A Q,R,S R210 119-1021-15 1/10W 1k ohm

HDCKR Q404 192-2712-00 2SC2712 R212 119-3331-15 1/10W 33k ohm
IC204 051-3340-00 LD1085P Q503 125-2027-91 DTC114EUA R215 119-4731-15 1/10W 47k ohm
IC205 051-3516-90 S-1132B33-U5T1G Q504 191-1197-50 2SB1197K Q,R R220 119-1041-15 1/10W 100k ohm
IC301 ---------- SAF7730HV/N317 Q506 125-2027-91 DTC114EUA R224 119-4721-15 1/10W 4.7k ohm
IC402 ---------- M30876FJBGP Q507 191-1197-50 2SB1197K Q,R R227 119-4721-15 1/10W 4.7k ohm
IC404 051-5417-08 S-80927CNMC-G8X Q509 193-2118-00 2SD2118F5 Q,R,S R229 119-4721-15 1/10W 4.7k ohm
IC406 051-9425-80 S-24CS64A0I-J8T1G Q512 125-2027-91 DTC114EUA R233 119-4721-15 1/10W 4.7k ohm
IC501 051-3019-90 NJM2060V Q515 193-1664-00 2SD1664 P,Q,R R248 116-2201-15 1/4W 22 ohm
IC502 051-3518-90 NJM2846DL3-33- Q516 192-4116-51 2SC4116 G,L R249 032-0140-98 1/10W 330 ohm F

TE1 Q517 191-1204-61 2SB1204 R,S,T R250 116-1221-15 1/4W 1.2k ohm
IC503 051-2042-00 TA8275H Q518 125-2027-91 DTC114EUA R251 032-0140-93 1/10W 2k ohm F
IC504 051-3396-90 NJM2386ADL3-33- Q519 191-1197-50 2SB1197K Q,R R252 119-1031-15 1/10W 10k ohm

TE1 Q520 192-4116-00 2SC4116 R301 119-1031-15 1/10W 10k ohm
IC505 051-3517-90 LT3481EMSE Q521 192-4081-00 2SC4081 R302 119-1031-15 1/10W 10k ohm

#TRPBF Q522 125-2027-91 DTC114EUA R303 119-2201-15 1/10W 22 ohm
IC506 051-5441-08 BD4828G-TR Q523 192-4081-00 2SC4081 R304 032-0140-80 1/10W 18k ohm F
J201 074-1302-12 TH12P-SOCKET R103 119-3321-15 1/10W 3.3k ohm R305 032-0140-80 1/10W 18k ohm F
J202 074-1237-69 19PIN R106 119-0000-05 1/10W 0 ohm JW R306 032-0140-80 1/10W 18k ohm F
J502 074-4009-20 SOCKET(20P) R109 119-3321-15 1/10W 3.3k ohm R307 032-0140-80 1/10W 18k ohm F
L105 010-2003-04 30uH R111 119-3321-15 1/10W 3.3k ohm R314 119-1011-15 1/10W 100 ohm
L106 010-3104-54 600 ohm/100MHz R112 119-0000-05 1/10W 0 ohm JW R315 119-1031-15 1/10W 10k ohm
L107 010-3104-54 600 ohm/100MHz R113 119-3321-15 1/10W 3.3k ohm R316 119-1021-15 1/10W 1k ohm
L108 010-2198-50 0.15uH R116 119-2741-15 1/10W 270k ohm R317 119-1031-15 1/10W 10k ohm
L301 010-3104-54 600 ohm/100MHz R117 119-3331-15 1/10W 33k ohm R318 119-3921-15 1/10W 3.9k ohm
L302 010-3104-54 600 ohm/100MHz R118 119-3931-15 1/10W 39k ohm R319 119-1031-15 1/10W 10k ohm
L303 010-3104-54 600 ohm/100MHz R121 119-3931-15 1/10W 39k ohm R320 119-3921-15 1/10W 3.9k ohm
L304 010-3104-54 600 ohm/100MHz R122 119-1031-15 1/10W 10k ohm R321 119-1031-15 1/10W 10k ohm
L305 010-3104-54 600 ohm/100MHz R123 119-1031-15 1/10W 10k ohm R322 119-0000-05 1/10W 0 ohm JW
L306 010-3104-54 600 ohm/100MHz R124 119-3931-15 1/10W 39k ohm R323 119-1031-15 1/10W 10k ohm
L307 010-3104-54 600 ohm/100MHz R125 119-1031-15 1/10W 10k ohm R324 119-1041-15 1/10W 100k ohm
L308 010-3104-54 600 ohm/100MHz R126 119-1011-15 1/10W 100 ohm R325 119-1041-15 1/10W 100k ohm
L309 010-3104-54 600 ohm/100MHz R127 119-4731-15 1/10W 47k ohm R326 119-1001-15 1/10W 10 ohm
L310 010-3104-54 600 ohm/100MHz R128 119-4731-15 1/10W 47k ohm R327 119-3921-15 1/10W 3.9k ohm
L311 010-3104-54 600 ohm/100MHz R129 119-4731-15 1/10W 47k ohm R328 119-0000-05 1/10W 0 ohm JW
L312 010-3104-54 600 ohm/100MHz R130 119-8221-15 1/10W 8.2k ohm R329 119-1021-15 1/10W 1k ohm
L313 010-3104-54 600 ohm/100MHz R131 119-1011-15 1/10W 100 ohm R330 119-3921-15 1/10W 3.9k ohm
L402 010-3406-54 2.2uH J R132 119-1011-15 1/10W 100 ohm R331 119-0000-05 1/10W 0 ohm JW
L501 010-3104-54 600 ohm/100MHz R134 119-1031-15 1/10W 10k ohm R332 032-0140-50 1/10W 10k ohm F
L503 010-3414-90 6.8uH R135 119-2231-15 1/10W 22k ohm R334 032-0140-50 1/10W 10k ohm F
P101 076-3011-66 16P R136 116-6891-15 1/4W 6.8 ohm R336 032-0140-50 1/10W 10k ohm F
P401 076-0478-59 PLUG (9P) R138 119-1031-15 1/10W 10k ohm R337 032-0140-50 1/10W 10k ohm F
P402 076-3011-72 22P R139 119-1041-15 1/10W 100k ohm R338 032-0140-50 1/10W 10k ohm F
Q101 198-3018-00 2SK3018 R140 119-1001-15 1/10W 10 ohm R339 032-0140-50 1/10W 10k ohm F
Q102 198-3018-00 2SK3018 R141 119-1031-15 1/10W 10k ohm R340 032-0140-50 1/10W 10k ohm F
Q104 125-9017-92 UMD3N-TR R143 119-2231-15 1/10W 22k ohm R341 119-1031-15 1/10W 10k ohm
Q105 125-2027-91 DTC114EUA R144 119-2231-15 1/10W 22k ohm R342 119-1031-15 1/10W 10k ohm
Q106 125-2027-91 DTC114EUA R145 119-1001-15 1/10W 10 ohm R343 119-1031-15 1/10W 10k ohm
Q107 125-2027-91 DTC114EUA R146 119-1031-15 1/10W 10k ohm R344 119-1011-15 1/10W 100 ohm
Q108 125-2027-91 DTC114EUA R148 116-1091-15 1/4W 1 ohm R345 119-1011-15 1/10W 100 ohm
Q109 192-5886-00 2SC5886 (PN-3124N-A) R346 119-0000-05 1/10W 0 ohm JW
Q110 125-2027-90 DTC143EU R149 116-1221-15 1/4W 1.2k ohm R347 119-0000-05 1/10W 0 ohm JW

(PN-3124N-A) (PN-3124N-A) R348 119-0000-05 1/10W 0 ohm JW
Q111 190-2060-00 2SA2060 R150 116-3911-15 1/4W 390 ohm R349 119-0000-05 1/10W 0 ohm JW

(PN-3124N-A) R151 119-1031-15 1/10W 10k ohm R350 119-1031-15 1/10W 10k ohm
Q112 125-9017-92 UMD3N-TR (PN-3124N-A) R351 119-0000-05 1/10W 0 ohm JW
Q201 192-4081-00 2SC4081 R153 119-1041-15 1/10W 100k ohm R352 119-4731-15 1/10W 47k ohm
Q204 125-9017-92 UMD3N-TR R162 119-0000-05 1/10W 0 ohm JW R353 119-1021-15 1/10W 1k ohm
Q206 198-3018-00 2SK3018 R165 119-1031-15 1/10W 10k ohm R354 119-1021-15 1/10W 1k ohm
Q207 198-3018-00 2SK3018 R166 119-1031-15 1/10W 10k ohm R355 119-1021-15 1/10W 1k ohm
Q219 125-2027-90 DTC143EU R167 119-1031-15 1/10W 10k ohm R356 119-1021-15 1/10W 1k ohm
Q220 191-1197-50 2SB1197K Q,R R168 119-1031-15 1/10W 10k ohm R357 119-4731-15 1/10W 47k ohm
Q222 125-9017-92 UMD3N-TR R169 119-1031-15 1/10W 10k ohm R358 119-1001-15 1/10W 10 ohm
Q301 125-7007-90 Si5441BDC-TI-E3 R170 119-1031-15 1/10W 10k ohm R359 119-4731-15 1/10W 47k ohm
Q302 125-2027-91 DTC114EUA R171 119-0000-05 1/10W 0 ohm JW R360 119-4731-15 1/10W 47k ohm
Q303 125-2027-91 DTC114EUA R172 119-0000-05 1/10W 0 ohm JW R361 119-4731-15 1/10W 47k ohm
Q304 125-2027-91 DTC114EUA R173 119-1531-15 1/10W 15k ohm R362 119-4731-15 1/10W 47k ohm
Q305 125-2027-91 DTC114EUA R174 119-2231-15 1/10W 22k ohm R400 119-0000-05 1/10W 0 ohm JW
Q306 125-2027-91 DTC114EUA R175 119-1021-15 1/10W 1k ohm R401 119-1021-15 1/10W 1k ohm
Q307 125-2027-91 DTC114EUA R176 119-3931-15 1/10W 39k ohm R402 119-1021-15 1/10W 1k ohm
Q308 125-2027-91 DTC114EUA R177 119-6821-15 1/10W 6.8k ohm R403 119-1021-15 1/10W 1k ohm
Q401 125-2027-91 DTC114EUA R207 119-3011-15 1/10W 300 ohm R404 119-0000-05 1/10W 0 ohm JW
Q402 125-0021-91 DTA114EUA R208 119-3011-15 1/10W 300 ohm R405 119-1021-15 1/10W 1k ohm

PN-3124N

-12-