Cisco Webex DX70, Webex DX80 User Manual

Download

Page 1

Cisco Webex

DX70, DX80

User Guide

CE 9.5

Page 2

What’s In This Guide

Contents

All entries in the table of contents are active hyperlinks (javascript enabled reading systems only) that will take you to the corresponding article.

To go between chapters, you may also

click on the icons in the sidebar.

Note! Some of the features described in

this user guide may be optional in certain markets and they may therefore not apply to your system.

Introduction

A Tour of the Cisco DX70 ......................................................... 4

About This User Guide ........................................................... 4

A Tour of the Cisco DX80 ......................................................... 5

DX80 and USB Headsets ....................................................... 5

Pairing with a Bluetooth Headset .............................................. 6

Logging On With Your Own Credentials .................................... 7

About Extension Mobility ........................................................ 7

Video Calls

Place Call From Contact List ..................................................... 9

About the Lists of Contacts ................................................... 9

Edit a Contact Before Calling .................................................. 10

About Entry Edits ................................................................. 10

Place Call Using Name, Number or Address ........................... 11

About Placing Calls .............................................................. 11

Incoming Calls ......................................................................... 12

If Someone Calls You ...........................................................12

Receive Call While in Another Call .......................................... 13

About the Options ................................................................ 13

Disconnect Yourself From Call ................................................ 14

About Disconnecting Yourself ..............................................14

Put Call on Hold and Resume a Call on Hold .......................... 15

About Putting on Hold .......................................................... 15

Transfer an Ongoing Call .........................................................16

About Transfer .....................................................................16

Change Call Rate .................................................................... 17

About Call Rate .................................................................... 17

Activate Do Not Disturb ........................................................... 18

About Do Not Disturb ........................................................... 18

Automated Forwarding of All Calls ..........................................19

About Forwarding Calls ........................................................ 19

View Keypad While in a Call ....................................................20

Using Keypad in a Call .........................................................20

Add Additional Participants to Existing Call ............................. 21

About Video Conferences .................................................... 21

Disconnect a Participant From a Conference .......................... 22

About Video Conferences .................................................... 22

Intelligent Proximity

Intelligent Proximity ................................................................. 24

About Proximity .................................................................... 24

Content Sharing

Sharing Content In a Call ........................................................ 26

About Content Sharing ........................................................ 26

Change Presentation Layout In a Call .....................................27

About Presentation Layout ...................................................27

Scheduled Meetings

Join a Scheduled Meeting ...................................................... 29

Joining a Meeting ................................................................ 29

Contacts

Favorites, Recents and Directory .............................................31

About the Contacts Lists ...................................................... 31

Add Someone to Favorites, While in a Call .............................32

About Favorites ....................................................................32

Add Someone to Favorites, Outside a Call ..............................33

About this feature ................................................................ 33

Camera Control

Turn Selfview On and O ........................................................35

Why Selfview? ..................................................................... 35

Move the Selfview PiP ............................................................36

Why Move the Selfview? ...................................................... 36

Far End Camera Control .......................................................... 37

About Camera Control ......................................................... 37

Settings

Overview of the Settings Accessible ....................................... 39

About Settings ..................................................................... 39

Page 3

Introduction

Page 4

This user guide applies to both DX70

and DX80. The display of the two are of dierent sizes, but the images displayed on the screens are identical apart from the size.

For practical purposes, the screenshots used in this guide have been inserted into a drawing of the DX80.

A Tour of the Cisco DX70

Introduction

About This User Guide

Camera with privacy shutter, turn counter-clockwise

to shut and clockwise to open

Microphone mute button and loudspeaker volume

controls

Loudspeaker SD card slot and connectors for headset and USB.

Note that the DX70 now supports the use of Bluetooth headsets, see two pages ahead for more.

Power On/O Microphone

Use as PC monitor. Use an HDMI cable to connect your computer to the HDMI socket PC (see below).

To switch between PC monitor and Video screen,

just tap the screen.

Incoming calls will appear as usual, irrespective of mode (PC or video) unless Do not disturb is active, see “Activate Do Not Disturb” on page

 USB ports

 HDMI socket PC  HDMI socket External Monitor (not in use)  LAN expansion connection. Connect your PC LAN here

to let your Cisco DX70 and PC share a common LAN connection

 LAN connection  Power supply socket

Page 5

The DX 80 implements the standard

protocol for USB wired audio devices.

Note that DX80 now supports the use of Bluetooth headsets — see the following page for more.

Manufacturers can implement the standard dierently (called HID protocol).

Consequently, dierent models from the same manufacturer can behave dierently and we cannot guarantee that all headsets and handsets will work.

For CE 9.2 we have only tested wired headsets or headsets working with a dongle.

Note that DX80 now supports the use of Bluetooth headsets, see the next page for more.

The provided list of headsets is

by no means exhaustive, many other headsets should work. We recommend that you check with Jabra, Plantronics and Sennheiser, as they are also doing their own testing and can provide their own list of headsets supporting DX80.

The following headsets have been

tested by Cisco:

•

Jabra Evolve 40

•

Jabra Evolve 65

•

Jabra Pro 9450

•

Jabra Pro 9470

•

Sennheiser MB Pro 2

Introduction

DX80 and USB Headsets

Camera with privacy shutter, turn counter-clockwise

to shut and clockwise to open

Microphone mute button, loudspeaker volume

controls and USB socket on the right side of the unit.

Power On/O Loudspeaker Microphone in each leg

  Power supply socket  USB computer connection  HDMI computer connection  HDMI external monitor connection (not in use)  SD card slot and Kensington lock  USB ports   LAN expansion connection. Connect your

computer LAN here to let your Cisco DX80 and computer share a common LAN connection

 LAN connection

Use as PC monitor. Use an HDMI cable to connect your computer to the HDMI socket PC (see below).

To switch between PC monitor and Video screen, just tap the screen.

Incoming calls will appear as usual, irrespective of mode (PC or video) unless Do not disturb is active, see “Activate Do

Not Disturb” on page 18.

A Tour of the Cisco DX80

Page 6

Introduction

Pairing with a Bluetooth Headset

Bluetooth Headsets

Bluetooth headset is supported on DX70 and DX80.

Bluetooth proles supported:

•

HFP (Hands-Free Prole)

•

A2DP (Advanced Audio Distribution Prole)

Bluetooth headset is supported directly with the embedded Bluetooth radio or by using a USB Bluetooth dongle.

Multiple headsets can be paired with the video system, but only one can be connected at a time.

The range is up to 10 m (30 ft). If you move outside the range when in a call, the audio will switch to the speakers on the video system.

Most headsets have built-in volume controls. When in a call, the volume of the headset and video system is synchronized. When not in a call, the volume buttons on the headset and video system operate independently.

Supported Bluetooth features:

•

Answer incoming calls

•

Reject incoming calls

•

Hang up calls

•

Volume up and down

Some headsets have mute control. This operates independently from the mute control on the video system.

Pairing a Bluetooth Headset

1. Activate Bluetooth pairing on the headset. If in doubt, consult the instruction manual for the headset.

2. Go to the Settings as explained at lower left. For more on the System information menu, see “Settings” on

page 38. If Bluetooth is disabled, turn it on. Bluetooth

is enabled by default.

3. The video system will scan for devices. Upon successful discovery the Bluetooth headset should be displayed in the device list.

4. Select the device and pairing begins. It may take a few seconds for the pairing to complete.

5. If the pairing is successful the video system will now list the headset as connected. The pairing is then completed.

USB Bluetooth Dongle

Using a USB Bluetooth dongle is recommended, as it gives better audio quality. When using the dongle the headset is detected as a USB headset.

Note that there will be no synchronization of headset volume and video system volume when using a dongle.

We have tested Jabra Link 360, Plantronics BT300 and Plantronics BT600; though others may work as well.

To start pairing tap

Settings, in which menu

you will nd Bluetooth

settings listed.

You may use Bluetooth pairing directly to the video system, or use a USB dongle.

You can switch between the speaker of the video system and the devices connected via Bluetooth or USB.

Select the icon in the status bar of the user interface, and choose from the available devices:

Speakers

Analog headset (DX70 only)

USB headset

USB handset

Bluetooth device

Icon appears here

Page 7

Introduction

Logging On With Your Own Credentials

Video systems located in meeting

rooms and quiet rooms and running under CUCM (Cisco Unied

Communications Manager) may allow you to log in to the video system with your own personal credentials.

CUCM will then route all incoming

calls destined for you to that specic video system.

Once you log out from Extension

Mobility your list of Recents wil be

cleared from the system.

Extension Mobility is also referred to

as Hot-desking.

About Extension Mobility

1 2 3

4 5

Tap the green Extension Mobility button.

The system will conrm that your Sign in was succesful.

To log out again, tap Sign out, as shown.

Key in your Username and PIN Code. Tap Login.

Page 8

Video Calls

Page 9

Tap that entry to produce the green Call button. Then tap the green Call button, as shown.

Tap the green Call button.

To search for someone in a specic list (Favorites, Directory or Recents), tap that list and then scroll down to locate the entry to be called.

The call will now be placed. To end the call, tap

the red End icon.

Your lists of Contacts consist of three

parts:

Favorites. These contacts have

been put there by you. These entries

will typically be someone you call

frequently or otherwise need to

access in a swift and convenient

manner from time to time.

Directory will typically be a corporate

directory installed on your system by your video support team.

Recents is a list of calls you have

placed, received or missed earlier.

The following options apply:

•

You may key in a name, number or an IP address and the system will look in all lists for you.

•

You may add the entry to the list of Favorites; edit aspects of the entry before calling and change the call rate.

Note that removing entries from

Recents can only be done from the

web interface.

Place Call From Contact List

Video Calls

About the Lists of

Contacts

1 2

Page 10

Tap Edit and Call.

Locate the entry to be edited before a call is placed. Tap that entry. This will produce the Call menu.

Tap the More (...) icon just below the green Call button.

Use the keyboard to edit and then tap either of the green Call buttons to place the call.

For how to enter the Contacts list, see

the previous page.

You may have to edit an entry in one

of the Contact lists before you place

the call. There may be a need to add

a prex, a sux or otherwise alter the

entry to ensure success.

Edit a Contact Before Calling

Video Calls

About Entry Edits

1 2

Page 11

Key in a name, number or address. Possible matches and/or suggestions will appear as you type. If the correct match appears in the list tap that match, otherwise keep typing.

Tap the green Call button.

Tap the Search or Dial eld. This will invoke the keyboard

When you have typed or located whom to call,

tap either of the green Call buttons to place the call.

You may call someone who is not

listed in your list of contacts by keying

in their name, address or number

using the virtual keyboard appearing

on the display.

Anyone you have previously called, or

who has called you, will appear in the

Recents list and you may transfer any

of them to your list of Favorites. This is

described in the section Contacts.

Sometimes you may be urged to enter

numbers during a call, typically to

reach extensions or to provide a pin

code.

Tap Touch Tones (this button appears

as soon as the call is placed) to invoke

the keypad needed for this.

Note that Recents can be cleared

from the web interface only.

Place Call Using Name, Number or Address

Video Calls

About Placing Calls

1 2

Page 12

Tap accordingly to accept (answer) or decline an incoming call.

If your video infrastructure permits it, you may receive multiple incoming calls. You will then have the choice of adding them all to an existing call, or decline them all.

•

If someone calls you, you may accept, decline or ignore the call.

•

If you decline the call, busy information will be sent to the calling part y.

•

If you ignore the call, the calling party will perceive this as if you were absent (you did not pick up the call).

•

Your video infrastructure may allow you to receive multiple incoming calls. Consult your video support team, if needed.

Incoming Calls

Video Calls

If Someone Calls You

Page 13

If you already are in a call, you may

accept another incoming call under

certain circumstances.

Receive Call While in Another Call

Video Calls

About the Options

Add: If your system

is running Ad hoc

conferencing under CUCM

you will be able to add

incoming participants.

Decline the incoming call and carry on as you have been doing.

The identity

of the new

incoming call.

Accept & Hold: Answer the call and put the existing call on hold.

Page 14

Tapping End in a call will disconnect yourself from a call. In a call with two

parties only, this will then terminate

the call.

Disconnect Yourself From Call

Video Calls

About Disconnecting

Yourself

To dsconnect yourself from a call, tap End.

Page 15

In a call, tap Hold.

Tap Resume to go back to the one you were in call with (to undo your action).

Putting someone on hold is typically

something you do as an initial step

when transferring someone to another

person, but it may also be used when you need to consult a person, or as

an alternative to muting where you

will also include stopping the video

transmission.

Put Call on Hold and Resume a Call on Hold

Video Calls

About Putting on Hold

1 2

Page 16

Tap the green Call button. Talk to the person to conrm that transfer is OK. The person to be transferred is still on hold.

Tap the Transfer button. This will cause the current call to be put on hold.

Search for whom to call in the usual way.

Tap Complete Transfer.

You may transfer an ongoing call to

another person. Transfer is always

consultative, i.e. you will be able to talk

to the person you are going to transfer

a call to, before you actually transfer

the call.

Transfer an Ongoing Call

Video Calls

About Transfer

1 2

Page 17

Move the slider to the required setting.

Tap the Call button (not shown), then locate the entry whose call rate you want to alter (not shown). Tap this entry to produce the Call menu and then tap the More (...) icon below the green Call button, as shown.

Tap Custom call.

Tap the green Call button to place the call.

Call rate is the term used to express

the amount of bandwidth allocated to

the call. It is measured in kbps (kilobits

per second).

The higher the call rate is, the better

the quality will be, but on the expense

of higher bandwidth consumption.

The system comes with a default

call rate. This is normally set by your video support team. Under normal

conditions the call rate will be adjusted

automatically by the system, whenever

needed. This is done to avoid choking

the video call when you try to call

someone at a higher rate than their

system and connection support.

If, for some reason, the automatic call

rate setting fails, you may also do this

manually as a last resort.

Call rate cannot be changed during a

call, but you may change it just before you place a call, as shown at left.

Change Call Rate

Video Calls

About Call Rate

1 2

Page 18

Tap in the upper left corner, as shown.

Your system can be set to not respond

to incoming calls. You may, however,

use it to call others as much as you

want.

Your video support team may have set

a time-out on this feature, after which

the system will return to respond to

incoming calls as usual. Default time-

out setting is 60 minutes.

About Do Not Disturb

Activate Do Not Disturb

Video Calls

Tap Do not disturb to activate the feature. Tap again to deactivate.

Page 19

Your video support team may have

activated the option of forwarding all

calls received. You may then choose

between voicemail and a receiver

appointed by you.

If you tap Forward all calls, the familiar

Call menu will appear letting you

specify whom to receive your calls.

About Forwarding Calls

Automated Forwarding of All Calls

Video Calls

You may now choose to forward all calls to either a receiver specied by you, or to your voicemail.

Tap in the upper left corner, as shown.

Page 20

In a call you may get prompted to

submit numbers to be able to reach

an extension or otherwise gain

entrance to something (for example

by means of a PIN-code).

To be able to submit this you will need

to invoke the keypad on the touch

screen.

View Keypad While in a Call

Video Calls

Using Keypad in a Call

In a call, tap Touch Tones to invoke the dial pad.

Page 21

Place the call, in the usual way. You may alter the Call settings of that call before you place it—see side bar for more.

In a call tap Add. Locate whom to call, in the usual way.

This new call will now be added to the existing

and you have now established a conference.

You may repeat this procedure to the extent permitted by your video infrastructure.

Your video system network may be

equipped with the capability to initiate

a video conference with several

participants.

The maximum number of participants

supported by your video system will

depend on system conguration and

the video infrastructure. If in doubt,

contact your video support team.

If you want to initiate a video

conference, you must call each

participant one by one.

If you are the one who initiated

the conference you will be able to

terminate the entire conference. The

other participants may only disconnect

themselves from the conference.

Add Additional Participants to Existing Call

Video Calls

About Video

Conferences

1 2

Page 22

The ability to conduct a video

conference from your DX70/80 is an

optional feature that may, or may not,

be available for your system.

Disconnect a Participant From a Conference

Video Calls

About Video

Conferences

Tap Drop.

In a call, tap the Participants icon in the upper right corner, as shown, to invoke the list of participants.

Tap the participant to be dropped from the conference.

1 2

Page 23

Intelligent Proximity

Page 24

Intelligent Proximity

On the Cisco Proximity Ultrasound Signal

Intelligent Proximity

About Proximity

Cisco video systems emit ultrasound as part of the Proximity feature. Most people are exposed to ultrasound more or less daily in many environments, including industry, commercial applications and home appliances.

Even if airborne ultrasound may cause subjective eects for some individuals, it is very unlikely that any eects will occur for sound pressure levels below 75 dB. Guidelines for ultrasound exposure limits vary heavily between countries, but 75 dB is the lowest limit presently found for the frequency band around 20 kHz, which is where the Cisco proximity signal is emitted.

A good reference for this information is Health Canada´s guidelines, http://www.hc-sc.gc.ca/ewh-

semt/pubs/radiation/safety-code_24-securite/ index-eng.php#a2.2.2.

These guidelines state that sound pressure levels lower than 120 dB have not been demonstrated to cause hearing losses, neither permanently nor temporarily.

For Cisco video systems for group use with integrated loudspeakers the ultrasound sound pressure level is below 75 dB at a distance of 50 cm or more from the loudspeaker.

For Cisco video systems for personal use the ultrasound sound pressure level is below 70 dB at a distance of 20 cm or more from the loudspeaker.

For Cisco WebEx Boards the ultrasound sound pressure level is below 75 dB at a distance of 20 cm or more in front of the display. The level can be slightly higher right below the display due to the downward-facing loudspeakers.

In most practical cases the level at the ear of the user will be much lower than these max levels, due to loudspeaker directivity, distance attenuation, and high degree of high frequency absorption in typical rooms. The levels will range from what for audible sound would be typical background / ambient noise levels in meeting spaces up to so-called conversational levels of normal speech.

It is therefore deemed safe for humans to be continously subjected to the proximity signal. Most people will not be aware of the presence of the signal, and suer no eects from it. A few individuals with especially acute high frequency hearing can, however, be able to hear it, this is most likely to happen directly in front of and close to the loudspeaker.

It is obvious that animals like dogs will hear the proximity signal, since their frequency range of hearing is so much wider.

However, the eect of sound is also level dependent, and the level range of a dog´s hearing is not signicantly dierent from that of a human. The hearing threshold of dogs at 20 kHz can be as low as 0–10 dB, similar to the threshold of a human ear in its most sensitive frequency range.

Cisco has not done testing or qualication of the possible eects the signal can have on dogs. Due to the limited levels it is believed that while the signal is clearly audible it is not bothersome to dogs.

A dog in an oce or meeting room will be subject to ultrasound at levels comparable to normal background noise, or at most conversational levels. There has been no reports of animals being bothered by the signals in the years we have had this feature in our products.

However, the question of ultrasound eect on dogs is fair, since dog repeller devices using ultrasound do exist. These devices typically claim to use discomforting, but not harmful ultrasound. Cisco does not have insight into dog repeller design, but scanning the specications of such devices typically reveals that the exposure levels typically are 100 dB and upwards.

For solutions using Cisco video codecs with 3rd party loudspeaker systems Cisco is not able to control the ultrasound sound pressure level. In most cases the necessary loudspeaker sensitivity and frequency response will result in levels below the 75 dB limit. However, if excessive external amplication is applied, or the loudspeaker system has an emphasized high-frequency response, levels in excess of the limit can be produced.

The Intelligent Proximity feature allows you to share content from a computer

wirelessly on the video system. Smart

phones and tablets are also able to view the shared content directly on

their own screens.

You can even use your own smart

phone, tablets, PC or MAC to control

calls on the video system.

Observe the following:

You will need to download (free of

charge) the Cisco Intelligent Proximity

app from App Store or Google Play.

Windows or OS X users, go to http s://

proximity.cisco.com/.

Your video support team may have

activated none of the features, all of

them, or just a subset of them.

Intelligent Proximity makes use of

ultrasound when connecting users

(see more at left). Do not block the

microphone of your computer, smart

phone or tablet.

Intelligent Proximity has been designed

not to work outside the meeting room

when doors to the room are kept

closed. You will need to be in close

proximity of the video endpoint to use

the fea ture.

When privacy dictates, always keep the

meeting room entrance doors closed

to avoid possible eavesdropping from

adjacent rooms.

Page 25

Content Sharing

Page 26

The content of your PC screen will now be shared with the other participants.

In a call, connect your source and make sure it is switched on. Tap Show PC to display the screen of your PC locally on your DX70/80. What you see on the screen when you do this, is not shown to the other participants.

If you do not want to share your PC screen with the others tap Hide PC to return to the previous state. Otherwise, tap Share, as shown to proceed to sharing content.

To stop sharing content, tap Stop sharing, as

shown.

Your video system supports the ability

to show presentations in a video call

or video conference .

Note that you may change the layout

of the screen during presentations,

see the next page for more on this.

Tip Your system camera can work as

a document camera. Just tilt it, as

shown, to present a document or any

other physical object that lies on your

table in front of the system.

The camera senses what you do to

it and automatically ips the image vertically. Thus, the image appears as

expected to the far end.

Sharing Content In a Call

Content Sharing

About Content Sharing

1 2

Page 27

Tap the Layout to invoke the layout options, as shown.

Select your preferred layout by tapping it.

You may change the layout of the

screen during presentations. Typical

options available will be with or

without showing the presenter and

showing the presenter as either a PiP

(Picture in Picture) or PoP (Picture

outside Picture).

The layout options available on

your system may dier from those

shown here, but the layouts shown

are always those you may choose

between.

Change Presentation Layout In a Call

Content Sharing

About Presentation

Layout

Page 28

Scheduled Meetings

Page 29

Your video system may be connected

to a management system capable

of scheduling video meetings. Any

meetings scheduled will then appear

as shown at left.

Tap Join to participate in the meeting.

Should the meeting have started

already, you may still join.

Join a Scheduled Meeting

Scheduled Meetings

Joining a Meeting

Page 30

Contacts

Page 31

Your lists of Contacts consist of three

parts:

Favorites. These contacts have

been put there by you. These entries

will typically be someone you call

frequently or otherwise need to

access in a swift and convenient

manner from time to time.

Directory will typically be a corporate

directory installed on your system by your video support team.

Recents is a list of calls you have

placed, received or missed earlier.

Note that removing entries from

Recents can only be done from the

web interface.

Favorites, Recents and Directory

Contacts

About the Contacts Lists

Page 32

Tap Favorite.

In a call, tap the Participants icon in the upper right corner, as shown, to invoke the list of participants.

Tap the participant to be turned into a Favorite. A small menu allowing you to drop that participant (terminate that participation) or to add the participant to the list of favorites.

The Favorites is your own shortlist of

contacts you frequently call or other-

wise want to have easy access to.

Favorites may be populated from the

Recents or Directory lists as well as

from manual entries.

Add Someone to Favorites, While in a Call

Contacts

About Favorites

1 2

Page 33

Tap Mark as Favorite. The entry has now become a Favorite. Tap anywhere outside the menu to exit.

While not in a call, tap Call (not shown) to invoke the Contacts list, as shown. Tap Recents or Directory and search for the entry to become a Favorite.

Tap the participant to be turned into a Favorite. This will cause the above screen to be shown. Tap the More (...) icon below the green Call button.

A Favorite is denoted by a golden star, as indicated.

To remove an entry from the list of Favorites, go

to Favorites in the Contact lists and repeat the procedure.

Add Someone to Favorites, Outside a Call

Contacts

The Favorites is your own shortlist of

contacts you frequently call or other-

wise want to have easy access to.

Favorites may be populated from the

Recents or Directory lists as well as

from manual entries.

To add a manual entry to the list of

Favorites, type the name or address in

the Search or Dial eld as explained

in “Place Call Using Name, Number or

Address” on page 11.

About this feature

1 2

Page 34

Camera Control

Page 35

Turn Selfview On and O

Camera Control

Selfview shows what others see from your video system. You will normally

use it to conrm that they see what you want them to see.

The selfview appears as a PiP

(Picture-in-Picture).

From time to time you may want to

have the selfview activated during the

meeting. This could, for example, be

to ensure that you remain seen on the

screen.

Tap as shown at left to activate or

deactivate the Selfview.

It may happen that the current position

of the selfview blocks important parts

of the image on your screen. You may

therefore want to move it (see the

next page for more).

Why Selfview?

Page 36

Drag the image to a new position, shown here is the upper left corner.

Tap and hold the selfview image. You will now see the alternate positions

available for the selfview image. Keep holding the image.

Release the image by lifting your nger from the screen. The selfview image has now assumed its new position.

Move the Selfview PiP

Camera Control

Selfview shows what others see from your video system. You will normally

use it to conrm that they see what you want them to see.

The selfview appears as a PiP

(Picture-in-Picture).

From time to time you may want to

have the selfview activated during the

meeting. This could, for example, be

to ensure that you remain seen on the

screen.

It may happen that the current position

of the selfview blocks important parts

of the image on your screen. You may

therefore want to move it.

Why Move the Selfview?

1 2

Page 37

Use the Pan, Tilt and Zoom controls as required.

Tap the Participant icon. Tap the praticipant, whose camera you want to

control, then tap Camera.

Tap somewhere outside the controls when you are

done.

Far End Camera Control

Camera Control

You may be in a video call, in which

one or more of the other video

systems have a remotely controllable

camera.

You will then be able to control those

cameras from your own video system. This is referred to as Far End Camera

Control (FECC).

If the far end system has activated

camera tracking (which takes place

when the camera tracks and shows

who is speaking) you will not be

oered the option of FECC.

About Camera Control

1 2

Page 38

Settings

Page 39

This menu is accessed by tapping

the little icon in the upper left corner

followed by tapping Settings. It provides

an overview of the well-being of your

DX70/DX80.

Overview of the Settings Accessible

Settings

About Settings

Provides video address

information, IP and MAC

address, SIP Proxy and the

current software version.

Activate, deactivate Bluetooth.

Lets you select ringtone and

set the volume of the ringtone.

Choose a call service.

Select between Wired and

Wireless (Wi-Fi) connection.

Restart the system.

Perform a Factory Reset to

return to Factory default

settings (not shown).

Page 40

Cisco has more than 200 oces worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco Website at www.cisco.com/go/oces.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its aliates in the U.S. and other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Americas Headquarters Cisco Systems, Inc. San Jose, CA

Asia P

acic Headquarters

Cisco Systems (USA) Pte. Ltd. Singapore

Europe Headquarters Cisco Systems International BV Amsterdam, The Netherlands