Installing Cisco TelePresence System Codec C60
Page 178-19806-02 Codec C60 Installation Sheet | December 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.
This box contains:
Codec C60
Top tray
TRC V remote control
A. Rack profiles (2 pcs)
B. Rack rear brackets (2 pcs)
C. Rack extension brackets (2 pcs)
D. Rack ear profiles (2 pcs)
Accessories box and cable kit
•
HDMI cable (3 m / 10 ft)
• Ethernet cable (5 m / 16 ft)
• Power cable (1.8 m / 6 ft)
• Batteries LR03 AAA 1.5 V for the remote control
• Screwdriver, combi 2 mm / 4 mm Allen Key (unbraco)
• Screws (M6 and M3) and cage nuts (M6)
• Universal rack brackets*
* Universal rack brackets: Use thes e only if the supplied rail based rack
mounting kit does not fit yo ur type of rack.
User guides
The user documentation for this product, including compliance
and safety information, is available on the Cisco web site.
Go to: http://www.cisco.com/go/cseries-docs
Rack mounting
WARRANTY: Rack mounting the codec without using the
supplied mounting kit will void the warranty.
b) Snap the cage
nuts to the rack.
1
Assembling the rack profiles
Slide the rack profiles A and B together.
3
Mounting the rack profiles to the rack
Mount the left and right rack profiles A+B(+C) to the rack. The screws,
screwdriver and cage nuts are found in the accessories box.
2
Optional: Assembling the extension rails
If the rack is deeper than the length of the
rack profiles A+B, then the extension rails C are
needed.
A+B
C
A
B
LEFT
RIGHT
d) On both sides:
Fasten the rack profiles A+B
together, using one M3 screw on
each side.
Tool: Screwdriver, 2 mm Allen Key
a) Mount the rack profiles in front
using two M6 screws on each side.
Tool: Screwdriver, 4 mm Allen Key
c) Mount the rack
profiles on the rear
side using the M6
knob screws.
Mount the extension rail (C) to the
rack profiles (A+B) using M6 screws.
Tool: Screwdriver, 4 mm Allen Key
Details in front
Details on rear side
AB BA
C
D D
Remote Control
A
B
A+B
C
Please follow the steps in
this installation guide when
rack mounting the codec.
NOTE: The profile should
be assembled with the
bend in the direction as
shown in the illustration.
NOTE: If the supplied rack profiles are incompatible
with the rack, use the supplied universal rack
brackets.
Follow the instructions in step 4 on the next page
when assembling the universal rack brackets.
Rack mounting and connecting cables
TIP
If the menu is not already present,
press Home key or OK key on the
remote control to open the menu.
Navigate in the menu with the
arrow key s.
4
7
ghi
pqrs
6
#
abc/123
9
1
.
@
5
0
8
jkl
tuv
2
abc
3
def
mno
wxyz
EMC Class A declaration
WARNING: This is a class A product. In a domestic environme nt this
product may cause radio inter ference in which case the user may be
required to take adequate measures.
声 明
此为A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对其干扰采取切实可行的措施。
Installing Cisco TelePresence System Codec C60
Page 278-19806-02 Codec C60 Installation Sheet | December 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.
4
Assembling the rack ear profiles
Mount the rack ear profiles to the codec.
5
Mounting the codec onto the rack
Locate the rails and carefully slide the codec onto the rack.
b) Fasten the codec in front
by tightening the screws on
the rack ear profiles.
Video from the camera
(HDMI to HDMI)
LAN/Ethernet Mains power
cable
Loudspeakers
(optional)
Camera control cable
(RJ45 to DSUB)
6
Connecting cables
The C60 codec offers a great flexibility in connecting
audio and video equipment to the system.
a) Remove the two M3 screws on
the left and right side of the codec.
Tool: Screwdriver, 2 mm Allen Key
b) Use the same two M3 screws to
fasten the rack ear profiles to the
codec.
a) Locate the rails on the codec and the
rails on the rack. Lift the codec towards
the rack and make sure the codec enter
the rails. Carefully slide the codec into the
rack.
Power switc h
After having
connected the
cables, you may
turn the codec On.
For a basic setup, you should go through these steps:
1. Connect the main camera to the HDMI 1 input using a
HDMI to HDMI cable
• For camera control you should also connect the
camera to the Camera Control input using the
dedicated cable that came with your camera (RJ45
to DSUB)
2. Connect the monitor display to the HDMI 1 output using
a HDMI to HDMI cable
3. If you want to send images from a PC, connect the PC
to the DVI-I 3 input, using a DVI to DVI or a HDMI to DVI
cable (for digital signals) or VGA to DVI cable (for analog
signals) depending on your PC’s capabilities
• Audio from the PC could be connected to Line 1
and 2 inputs for stereo signals
4. Connect the microphone to the XLR input
5. The loudspeakers should be connected to Line 1 and 2
outputs
6. Connect the codec to the IP network using the
Ethernet 1 interface
7. Connect the power and use the power switch to turn
the codec on
NOTE: If using the DVI-I out 2 for the main monitor a shortcut
is required to move the on screen display (OSD) to this
output. On the remote control key in the following sequence:
• Disconnect – * – # – * – # – 0 – 2 – #
PC (audio to Line In 1)
Monitor (audio from
HDMI 1 or Line Out 1-2)
Microphone
INPUTS OUTPUTS Basic setup
The main connector s for basic
setup are highlighted i n orange.
1 1
IMPORTANT
There should always be a distance of
minimum 10 cm / 4 in. free space in front
of the codec.
SAFETY REQUIREMENT
Make sure the codec is not mounted with
the front side up or down.
Min. 10 cm
Basic setup - The main connectors are highlighted in orange color.
Loading...