Cisco Systems SR2024C, SR2016 User Manual

Quick Start Guide

Product Overview

Thank you for choosing the 16-Port or 24-Port 10/100/1000 Gigabit Switch. The 16-Port and 24-Port 10/100/1000 Gigabit Switches provide non-blocking, wirespeed switching for your 10, 100, and 1000 megabit network clients.

Front Panel

The 16-and 24-Port 10/100/1000 Gigabit Switches differ in number of LEDs and ports. The LEDs and ports are located on the front panel of the Switch.

Front Panel of the SR2016

Back Panel

The power port is located on the back panel of the Switch.The power port is where you connect the included power cord.

Side Panel

Located on the side panel, the security slot is where you can attach a lock to guard against theft.

To rack mount the Switch, follow these instructions:

STEP 1 The Switch has four mounting holes on each side. Screw an

included mounting bracket into each side.

TEP 2 Place the Switch in the rack, and secure the brackets with additional

screws.

To wall-mount the Switch, follow these instructions:

STEP 1 The wall-mount slots are two crisscross slots on the Switch’s

bottom panel. The distance between the two slots is 95 mm (3.74 inches). Attach two screws to the wall, so that the Switch’s wall-mount slots line up with the two screws.

TEP 2 Maneuver the Switch so the screws are inserted into the two slots.

Typical Installation Scenario

The application diagram shown is an example of a typical network configuration. This diagram shows the front panel of the SR2024C and is used only as a reference.

Cisco Small Business Models SR2016 and SR2024C 16 and 24-Port 10/100/1000 Gigabit Switches

Package Contents

• SR2016 or SR2024C Gigabit Switch

• Power Cord

• Quick Start Guide

Front Panel of the SR2024C

System—(Green) The System LED lights when the Switch is powered on.

Link/Act—(Green) Each LED lights when there is a connection made through the corresponding port. The LED also flashes when there is activity on the corresponding port.

Gigabit—(Amber) Each LED lights when there is a Gigabit connection made through the corresponding port. The LED flashes when there is activity on the corresponding port.

1-16 (SR2016) or 1-24 (SR2024C)—The Ethernet ports connect to network devices, such as PCs or additional switches. All ports are auto-negotiating and have automatic MIDI/MIDI-X crossover detection.

Mini-GBIC 1-2 (SR2024C)—The SR2024C Switch is equipped with two miniGBIC ports. These ports provide links to high-speed network segments or individual workstations at speeds of up to 1000Mbps (Gigabit Ethernet). These ports are shared. If you use the mini-GBIC1 port, you cannot use port 12. If you use the mini-GBIC2 port, you cannot use port 24.

Placement Options

There are three ways to physically install the Switch:

• Set the Switch on its four rubber feet

• Mount the Switch in a standard-sized rack (1U high)

• Wall-mount the Switch using the wall-mount slots

Rack Mount Instruction Tips

• Ambient Temperature—To prevent the switch from overheating, do not

operate the switch in an area that exceeds the recommended ambient temperature.

• Reduced Air Flow—If you install the switch in a rack, be sure that there is

adequate air flow as required.

• Mechanical Loading—Be sure that the switch is level and stable when you

mount the switch in a rack to avoid any hazardous condition.

• Circuit Overloading—Do not overload the power outlet or circuit when

installing multiple devices in a rack.

• Reliable Grounding—Be sure that the switch is grounded and use suitable

electrical supply connections.

When you connect your network devices, make sure you don’t exceed the maximum cabling distances, listed in the following table.

From To Maximum Distance

Switch Switch 100 meters (328 feet)

Switch Computer 100 meters (328 feet)

NOTE Use Category 5e Ethernet network cables for your Gigabit

connections.

Installation

Specifications

The following table lists the specifications for the SR2024C 10/100/1000 Gigabit Switch.

Where to Go From Here

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Perform the steps in this section to install the hardware.

STEP 1 Make sure all the devices you will connect to the Switch are

powered off.

TEP 2 Connect a Category 5 Ethernet network cable to one of the numbered

ports on the Switch. Connect the other end to a PC or other network device.

TEP 3 Repeat step 2 to connect additional devices.

TEP 4 If you are using a mini-GBIC port, connect a mini-GBIC module to the

port. For detailed instructions, refer to the module’s documentation.

NOTE The mini-GBIC ports are shared. Do not use port 12 if you

are using themini-GBIC1 port. Do not use port 24 if you are using the mini-GBIC2 port.

TEP 5 Connect the supplied power cord to the Switch’s power port, and plug

the other end into an electrical outlet. When connecting power, always use a surge protector.

TEP 6 Power on the devices connected to the Switch. Each active port’s

corresponding LED will light up on the Switch.

Congratulations! The installation of the 10/100/1000 Gigabit Switch is complete!

The following table lists the specifications for the SR2016 10/100/1000 Gigabit Switch.

Model SR2016

Standards IEEE 802.3, 802.3u, 802.3x,

802.3ab

Ports 16 10/100/1000 Mbps RJ-45

ports

Cabling Type Cat5 Ethernet

LEDs System, 1 through 16

Dimensions WxHxD

10.98” x 1.75” x 9.45” 279 mm x 44.5 mm x 240 mm

Unit Weight 4.75 lbs (2.155 kg)

Power 110-120VAC, 100W

Certification FCC Class A, CE

Operating Temperature 32 to 104ºF (0 to 40ºC)

Storage Temperature -40 to 158ºF (-40 to 70ºC)

Operating Humidy 20% to 95%, noncondensing

Storage Humidy 5% to 95%, noncondensing

Model SR2024C

Standards IEEE 802.3, 802.3u, 802.3x,

802.3ab

Ports 24 10/100/1000 Mbps RJ-45

ports + 2 mini-GBIC ports

Cabling Type Cat5 Ethernet

LEDs System, 1 through 24

Dimensions WxHxD

17.00” x 1.75” x 13.74” 432 mm x 44.5 mm x 349 mm

Unit Weight 7.98 lbs (3.621 kg)

Power 100-127/200-240V~1.0A /0.5A

50~60HZ

Certification FCC Class A, CE

Operating Temperature 32 to 104ºF (0 to 40ºC)

Storage Temperature -4 to 158ºF (-20 to 70ºC)

Operating Humidity 10% to 90%, noncondensing

Storage Humidity 10% to 95%, noncondensing

Resource Location

Customer Support www.cisco.com/go/smallbiz

End User License Agreement www.cisco.com/go/smallbiz

Regulatory Compliance and Safety Information

Warranty Information www.cisco.com/go/smallbiz

Cisco Partner Central site for Small Business

www.cisco.com/go/smallbiz

www.cisco.com/web/partners/sell/ smb/

Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R)

Printed in the USA on recycled paper containing 10% postconsumer waste.

78-18816-01