Cisco Systems ONS 15454 User Manual

APPENDIX

A

Hardware Specifications

Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms

do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's
path protection feature, which may be used in any topological network configuration. Cisco does not
recommend using its path protection feature in any particular topological network configuration.

This appendix contains hardware and software specifications for the ONS 15454.

The following sections are included:

• A.1 Shelf Specifications, page A-1

• A.2 SFP, XFP, and GBIC Specifications, page A-4

• A.3 General Card Specifications, page A-7

• A.4 Common Control Card Specifications, page A-12

• A.5 Electrical Card Specifications, page A-17

• A.6 Optical Card Specifications, page A-27

• A.7 Ethernet Card Specifications, page A-48

• A.8 Storage Access Networking Card Specifications, page A-53

A.1 Shelf Specifications

This section provides specifications for shelf bandwidth; a list of topologies; Cisco Transport Controller
(CTC) specifications; LAN, TL1, modem, alarm, and electrical interface assembly (EIA) interface
specifications; timing, power, and environmental specifications; and shelf dimensions.

A.1.1 Bandwidth

The ONS 15454 has the following bandwidth specifications:

• Total bandwidth: 240 Gbps

• Data plane bandwidth: 160 Gbps

• SONET plane bandwidth: 80 Gbps

April 2008

Cisco ONS 15454 Reference Manual, R8.0

A-1

A.1.2 Configurations

A.1.2 Configurations

The ONS 15454 can be configured as follows:

• Two-fiber path protection

• Path protected mesh network (PPMN)

• Two-fiber bidirectional line switch ring (BLSR)

• Four-fiber BLSR

• Add-drop multiplexer (ADM)

• Terminal mode

• Regenerator mode

• Hubbed rings

• Multihubbed rings

• Point-to-point

• Linear

• Linear with optical add/drop multiplexing (OADM)

Appendix A Hardware Specifications

A.1.3 Cisco Transport Controller

CTC, the ONS 15454 craft interface software, has the following specifications:

• 10BaseT

• TCC2/TCC2P access: RJ-45 connector

• Backplane access: LAN pin field

A.1.4 External LAN Interface

The ONS 15454 external LAN interface has the following specifications:

• 10BaseT Ethernet

• Backplane access: LAN pin field

A.1.5 TL1 Craft Interface

The ONS 15454 TL1 craft interface has the following specifications:

• Speed: 9600 bps

• TCC2/TCC2P access: EIA/TIA-232 DB-9 type connector

• Backplane access: CRAFT pin field

A.1.6 Modem Interface

The ONS 15454 modem interface has the following specifications:

Cisco ONS 15454 Reference Manual, R8.0

A-2

April 2008

Appendix A Hardware Specifications

• Hardware flow control

• TCC2/TCC2P: EIA/TIA-232 DB-9 type connector

A.1.7 Alarm Interface

The ONS 15454 alarm interface has the following specifications:

• Visual: Critical, Major, Minor, Remote

• Audible: Critical, Major, Minor, Remote

• Alarm contacts: 0.045 mm, –48 V, 50 mA

• Backplane access: Alarm pin fields

A.1.8 EIA Interface

The ONS 15454 EIA interface has the following specifications:

• SMB: AMP #415504-3 75-ohm, 4-leg connectors

• BNC: Trompeter #UCBJ224 75-ohm 4 leg connector (King and ITT are also compatible)

A.1.7 Alarm Interface

• AMP Champ: AMP#552246-1 with #552562-2 bail locks

A.1.9 BITS Interface

The ONS 15454 building integrated timing supply (BITS) interface has the following specifications:

• 2 DS-1 BITS inputs

• 2 derived DS-1 outputs

• Backplane access: BITS pin field

A.1.10 System Timing

The ONS 15454 has the following system timing specifications:

• Stratum 3 per Telcordia GR-253-CORE

• Free running accuracy: +/–4.6 ppm

• Holdover stability: 3.7 x10

• Reference: External BITS, line, internal

A.1.11 System Power

–7

per day, including temperature (< 255 slips in first 24 hours)

April 2008

The ONS 15454 has the following power specifications:

• Input power: –48 VDC

• Power consumption: Configuration dependent; 72 W (fan tray only)

• Power requirements: –40.5 to –57 VDC

Cisco ONS 15454 Reference Manual, R8.0

A-3

A.1.12 Fan Tray

A.1.12 Fan Tray

Table A-1 lists power requirements for the fan-tray assembly.

Table A-1 Fan Tray Assembly Power Requirements

Fan Tray Assembly Watts Amps BTU/Hr

FTA2

FTA3 -T

15454-CC-FTA

Appendix A Hardware Specifications

• Power terminals: #8-32 screw. Ring or fork type lug suitable for 10 AWG stranded conductor with

a 0.375-inch maximum width.

• ANSI shelf: Two 30 A fuses (customer supplied fuse and alarm panel)

• HD shelf: 30 A fuse per shelf (customer supplied fuse and alarm panel)

53 1.21 198

86.4 1.8 295

115 2.4 393

A.1.13 System Environmental Specifications

The ONS 15454 has the following environmental specifications:

• Operating temperature: 0 to +55 degrees Celsius; –40 to +65 degrees Celsius with industrial

temperature rated cards

• Operating humidity: 5 to 95 percent, noncondensing

A.1.14 Dimensions

The ONS 15454 shelf assembly has the following dimensions:

• Height: 18.25 in. (46.3 cm)

• Width: 19 or 23 in. (48.3 cm or 58.4 cm) with mounting ears attached

• Depth: 12.018 in. (30.5 cm) for standard door and 13.810 in. (35 cm) for deep door

• Weight: 55 lb (24.947 kg) empty

A.2 SFP, XFP, and GBIC Specifications

Table A-2 lists the specifications for the available Small Form-factor Pluggables (SFPs), 10 Gbps

Pluggables (XFPs) and GBICs. In the table, the following acronyms are used:

• ESCON = Enterprise System Connection

A-4

• FICON = fiber connectivity

• GE = Gigabit Ethernet

• FE = Fast Ethernet

• E = Ethernet (10 Mbps)

• FC = Fibre Channel

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

• HDTV = high definition television

• CWDM = coarse wavelength division multiplexing

Table A-2 SFP, XFP, and GBIC Specifications

A.2 SFP, XFP, and GBIC Specifications

SFP/XFP Product ID Interface

15454-SFP-LC-SX/

GE –9.5 to –4 –17 to 0

Transmitter Output
Power Min/Max (dBm)

Receiver Input Power
Min/Max (dBm)

15454E-SFP-LC-SX

15454-SFP-LC-LX/

GE –9.5 to –3 –19 to –3

15454E-SFP-LC-LX

15454-SFP3-1-IR= OC-3 –15 to –8 –23 to –8

15454E-SFP-L.1.1= STM-1 –15 to –8 –34 to –10

15454-SFP12-4-IR= OC-12, D1 Video –15 to –8 –28 to –7

15454E-SFP-L.4.1= STM-4, D1 Video –15 to –8 –28 to –8

15454-SFP-OC48-IR= OC-48, DV6000 (C-Cor) –5 to +0 –18 to +0

ONS-SE-2G-S1= OC-48, STM-16 –10 to –3 –18 to –3

15454E-SFP-L.16.1= STM-16, DV6000

–5 to +0 –18 to +0

(C-Cor)

15454-SFP-200/

ESCON –8 to –4 –28 to –3

15454E-SFP-200

15454-SFP-GEFC-SX=/
15454E-SFP-GEFC-S=

15454-SFP-GE+-LX=/
15454E-SFP-GE+-LX=

FC (1 and 2 Gbps),
FICON, GE

FC (1 and 2 Gbps),
FICON, GE, HDTV

–10 to –3.5 –17 to 0 (1 FC and 1GE)

–15 to 0 (2 FC)

–9.5 to –3 –20 to –3

(1 FC, 1GE, and 2 FC)

ONS-SE-200-MM= ESCON –20.5 to –15 –14 to –29

ONS-SE-G2F-SX= Fibre Channel

(1 and 2 Gbps), GE

ONS-SE-G2F-LX= Fibre Channel

(1 and 2 Gbps), FICON,
GE, HDTV

–9.5 to 0 (GE)
–10 to –3.5 (1G and
2G FC/FICON)

–9.5 to –3 (GE)
–10 to –3.5 (1FC, 2FC,
and FICON)

–17 to 0
–22 (1G FC/FICON)
–20 (2G FC/FICON)

–19 to –3
–22 (1G FC/FICON)
–21 (2G FC/FICON)

ONS-SC-GE-SX= GE –9.5 to 0 –17 to 0

2

2

ONS-SC-GE-LX= GE –9.5 to–3 –19 to –3

ONS-SI-2G-S1 OC-48 SR –10 to –3 –18 to –3

ONS-SI-2G-I1 OC-48 IR1 –5 to 0 –18 to 0

ONS-SI-2G-L1 OC-48 LR1 –2 to 3 –27 to –9

ONS-SI-2G-L2 OC-48 LR2 –2 to 3 –28 to –9

ONS-SC-2G-30.3

OC-48 DWDM 0 to 4 –28 to –9
through
ONS-SC-2G-60.6

ONS-SI-622-I1 OC-3/OC-12 IR1 Dual

–15 to –8 –28 to –8

rate

1

(GE)

3

(GE)

3

April 2008

Cisco ONS 15454 Reference Manual, R8.0

A-5

A.2 SFP, XFP, and GBIC Specifications

Table A-2 SFP, XFP, and GBIC Specifications (continued)

Appendix A Hardware Specifications

SFP/XFP Product ID Interface

Transmitter Output
Power Min/Max (dBm)

Receiver Input Power
Min/Max (dBm)

ONS-SI-622-L1 OC-12 LR1 –3 to 2 –28 to –8

ONS-SI-622-L2 OC-12 LR2 –3 to 2 –28 to –8

ONS-SE-622-1470

OC-12 CWDM 0 to 5 –28 to –7
through
ONS-SE-622-1610

ONS-SI-155-I1 OC-3 IR1 –15 to –8 –28 to –8

ONS-SI-155-L1 OC-3 LR1 –5 to 0 –34 to –10

ONS-SI-155-L2 OC-3 LR2 –5 to 0 –34 to –10

ONS_SE-155-1470

OC-3 CWDM 0 to 5 –34 to –7
through
ONS-SE-155-1610

ONS-XC-10G-S1 OC-192 SR1 –6 to –1 –11 to –1

ONS-XC-10G-I2 OC-192 IR2 –1 to +2 –14 to +2

ONS-XC-10G-L2 OC-192 LR2 0 to 4 –24 to –7

ONS-SE-100-FX FE –20 to –14 –30 to –14

ONS-SE-100-LX10 FE –15 to –8 –25 to –8

15454-GBIC-SX FC, GE –9.5 to –3.5 –19 to –3

15454E-GBIC-SX GE, FC — —

15454-GBIC-LX/LH GE, FC –9 to –3 –19 to –3

15454E-GBIC-LX/LH GE, FC –9 to –3 –19 to –3

ONS-GX-2FC-MMI FC –9.5 to –5 –20.5/–15 max

ONS-GX-2FC-SML FC –9 to –3 –18 to –3

ONS-SI-155-SR-MM= OC-3, STM-1 -20 to -14 -30 to -14

ONS-SI-622-SR-MM= OC-12, STM-4 -20 to -14 (50

-26 to -14

micrometer)

-24 to -14 (62.5
micrometer)

ONS-SC-Z3-1470=

OC48/STM16/GE 0 to +5 -7 (min)
through
ONS-SC-Z3-1610=

ONS-SE-Z1= OC-3/STM1

OC-12/STM-4

OC-48/STM-16

Fibre Channel

(1 and 2 Gbps)

-5 to 0 -10 to -23 (OC-3)
0 to -23 (OC-12)

-18 to 0 (OC-48)
0 to -21 (Fibre Channel)
0 to -22 (GE)

GE

ONS-SI-2G-S1 OC-48/STM-16 -10 to -3 -3 min

A-6

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

Table A-2 SFP, XFP, and GBIC Specifications (continued)

A.3 General Card Specifications

SFP/XFP Product ID Interface

ONS-SE-155-1470

OC-3/STM-1 0 to 5 -7 to 0

Transmitter Output
Power Min/Max (dBm)

Receiver Input Power
Min/Max (dBm)

through
ONS-SE-155-1610

ONS-SE-622-1470

OC-12/STM-4 0 to 5 -7 to 0
through
ONS-SE-622-1610

ONS-SI-GE-SX GE -3 to 9.5 0 to -17

ONS-SI-GE-LX GE -3 to 9.5 0 to 17

ONS-SI-GE-ZX GE +5 to 0 0 to -23

ONS-SI-100-FX FE — —

ONS-SI-100-LX10 FE — —

ONS-SE-ZE-EL E, FE, or GE — —

ONS-SE-100-BX10U FE -3 to 9 -3 to 19.5

ONS-SE-100-BX10D FE -3 to 9 -3 to 19.5

1. Based on any valid 8B/10B code pattern measured at, or extrapolated to, 10E-15 BER measured at center of eye

2. Minimum Stressed Sensitivity (10-12): -12.5(62.5um) and -13.5(50um) dBm

3. Minimum Stressed Sensitivity (10

–12

): -14.4 dBm

A.3 General Card Specifications

This section provides power specifications and temperature ranges for all ONS 15454 cards.

A.3.1 Power

Table A-3 provides power consumption information for the ONS 15454 cards.

April 2008

Cisco ONS 15454 Reference Manual, R8.0

A-7

Appendix A Hardware Specifications

A.3.1 Power

Table A-3 Individual Card Power Requirements

Card Type Card Name Watts Amperes BTU/Hr.

Control Cards

TCC2 19.20 0.4 66.8

TCC2P 27.00 0.56 92.2

XCVT 34.40 0.72 117.46

XC10G 48 1 163.68

XC-VXC-10G 67 1.4 228.62

AIC-I 4.8 0.1 15.3

AEP 3 (from +5 VDC

10.2

from AIC-I)

FTA3 Fan Tray –48 VDC 129.60 2.7 442.21

FTA4 Fan Tray –48 VDC 115 2.4 393

Electrical Cards

EC1-12 36.60 0.76 124.97

DS1-14 12.60 0.26 43.02

DS1N-14 12.60 0.26 43.02

DS1/E1-56 36.00 0.76 124.97

DS3-12 38.20 0.79 130.43

DS3/EC1-48 30 0.58 95.6

DS3N-12 38.20 0.79 130.43

DS3i-N-12 30 0.63 102.4

DS3-12E 26.80 0.56 91.51

DS3N-12E 26.80 0.56 91.51

DS3XM-12 Transmux 34 0.71 116.1

DS3XM-6 Transmux 20 0.42 68

A-8

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

A.3.1 Power

Table A-3 Individual Card Power Requirements (continued)

Card Type Card Name Watts Amperes BTU/Hr.

Optical Cards

OC3 IR 4 19.20 0.40 65.56

OC3 IR 4/STM1 SH 1310 19.20 0.40 65.56

OC3 IR 4/STM1SH 1310-8 26.00 0.48 78.5

OC12 IR 1310 10.90 0.23 37.22

OC12 LR 1310 9.28 0.2 31.68

OC12 LR 1550 9.28 0.2 31.68

OC12 LR/STM4 LH 1310 9.00 0.2 31.68

OC12 LR/STM4 LH 1550 9.28 0.2 31.68

OC12 IR/STM4 SH 1310-4 35.60 0.74 121.6

OC48 IR 1310 32.20 0.67 109.94

OC48 LR 1550 26.80 0.56 91.50

OC48 IR/STM16 SH AS 1310 37.20 0.77 127.01

OC48 LR/STM16 LH AS 1550 37.20 0.77 127.01

OC48 ELR/STM16 EH 100 GHz 31.20 0.65 106.53

OC48 ELR 200 GHz 31.20 0.65 106.53

OC192 SR/STM64 IO H 1310 41.80 0.90 132.00

OC192 IR/STM64 SH 1550 48.00 1.00 163.68

OC192 LR/STM64 LH 1550 41.80 0.90 132.00

OC192 LR/STM64 LH 15xx.xx 62.40 1.30 214.00

15454_MRC-12 38 0.79 129.66

MRC-2.5G-4 38 0.79 129.66

Ethernet Cards

OC192SR1/STM64IO Short Reach
and OC-192/STM64 Any Reach

1

E100T-12 65 1.35 221.93

40 0.83 136.49

E100T-G 65 1.35 221.93

E1000-2 53.50 1.11 182.67

E1000-2-G 53.50 1.11 182.67

G1K-4 63.00 (including GBICs

2

) 1.31 215.11

ML100T-12 53 1.10 181.00

ML1000-2 49 (including SFPs) 1.02 167.30

ML100X-8 65 1.35 221.93

ML-MR-10 75 N/A N/A

CE-100T-8 53.14 1.10 181.30

CE-1000-4 60 1.25 204.80

CE-MR-10 65 1.35 221.93

April 2008

Cisco ONS 15454 Reference Manual, R8.0

A-9

Appendix A Hardware Specifications

A.3.2 Temperature

Table A-3 Individual Card Power Requirements (continued)

Card Type Card Name Watts Amperes BTU/Hr.

Storage Access
Networking

1. These cards are designated as OC192-XFP in CTC.

2. GBICs = Gigabit Interface Converters

FC_MR-4 60 1.25 212.00

A.3.2 Temperature

Table A-4 provides temperature ranges and product names for ONS 15454 cards.

Note The I-Temp symbol is displayed on the faceplate of an I-Temp compliant card. A card without this

symbol is C-Temp compliant.

Table A-4 Card Temperature Ranges and Product Names

Card Type Card Name

Control Cards

TCC2 — 15454-TCC2

TCC2P — 15454-TCC2P

XCVT 15454-XC-VT 15454-XC-VT-T

XC10G 15454-XC-10G —

XC-VXC-10G — 15454-XC-VXC-10G-T

AIC-I — 15454-AIC-I

AEP — 15454-AEP

Electrical

EC1-12 15454-EC1-12 15454-EC1-12-T

DS1-14 15454-DS1-14 15454-DS1-14-T

DS1N-14 15454-DS1N-14 15454-DS1N-14-T

DS1/E1-56 — 15454-DS1E1-56

DS3-12 15454-DS3-12 15454-DS3-12-T

DS3/EC1-48 — 15454-DS3_EC1-48

DS3N-12 15454-DS3N-12 15454-DS3N-12-T

DS3i-N-12 15454-DS3i-N-12 —

DS3-12E — 15454-DS3-12E-T

DS3N-12E — 15454-DS3N-12E-T

DS3XM-12 (Transmux) — 15454-DS3XM-12

DS3XM-6 (Transmux) 15454-DS3XM-6 15454-DS3XM-6-T

C-Temp Product Name
(32 to 131 degrees
Fahrenheit, 0 to +55
degrees Celsius)

I-Temp Product Name
(–40 to 149 degrees
Fahrenheit, –40 to +65
degrees Celsius)

A-10

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

Table A-4 Card Temperature Ranges and Product Names (continued)

A.3.2 Temperature

Card Type Card Name

Optical

OC3 IR 4/STM1 SH 1310 15454-OC34IR1310 15454-OC34I13-T

OC3 IR/STM1 SH 1310-8 15454-OC3I8-1310 —

OC12 IR/STM4 SH 1310 15454-OC121IR1310 15454-OC121I13-T

OC12 LR/STM4 LH 1310 15454-OC121LR1310 15454-OC121L13-T

OC12 LR/STM4 LH 1550 15454-OC121LR1550 15454-OC121L15-T

OC12 IR/STM4 SH 1310-4 15454-OC12I4-1310 —

OC48 IR 1310 15454-OC481IR1310 —

OC48 LR 1550 15454-OC481LR1550 —

OC48 IR/STM16 SH AS 1310 15454-OC481IR1310A —

OC48 LR/STM16 LH AS 1550 15454-OC481LR1550A —

OC48 ELR/STM16 EH 100 GHz 15454-OC48E-1-xx.xx

OC48 ELR/STM16 EH 200 GHz 15454-OC48E-xx.xx

OC 192 SR/STM64 IO 1310 15454-OC192IO1310 —

OC192 IR/STM64 SH 1550 15454-OC192IR1550 —

OC192 LR/STM64 LH 1550 15454-OC192LR1550 —

OC192 LR/STM64 LH ITU
15xx.xx

15454_MRC-12 — 15454-MRC-12-T

MRC-2.5G-4 — 15454-MRC-I-4

OC-192/STM-64 SR1 Short

1

Reach

OC-192/STM-64 Any Reach

C-Temp Product Name
(32 to 131 degrees
Fahrenheit, 0 to +55
degrees Celsius)

(all wavelengths)

(all wavelengths)

15454-OC192LR15xx —

15454_OC-192/STM-64
SR1 Short Reach

1

15454_OC-192/STM-64
Any Reach

I-Temp Product Name
(–40 to 149 degrees
Fahrenheit, –40 to +65
degrees Celsius)

—

—

—

—

April 2008

Cisco ONS 15454 Reference Manual, R8.0

A-11

A.4 Common Control Card Specifications

Table A-4 Card Temperature Ranges and Product Names (continued)

Appendix A Hardware Specifications

Card Type Card Name

Ethernet

E100T-12 15454-E100T —

E100T-G 15454-E100T-G —

E1000-2 15454-E1000-2 —

E1000-2-G 15454-E1000-2-G —

G1K-4 15454-G1K-4 —

ML100T-12 15454-ML100T-12 —

ML1000-2 15454-ML1000-2 —

ML100X-8 — 15454-ML100X-8

ML-MR-10 — 15454-ML-MR-10

CE-100T-8 15454-CE100T-8 —

CE-1000-4 15454-CE1000-4 —

CE-MR-10 15454-CE-MR-10 —

Storage
Access
Networking

1. Designated as OC192-XFP in CTC.

FC_MR-4 15454-FC_MR-4 —

C-Temp Product Name
(32 to 131 degrees
Fahrenheit, 0 to +55
degrees Celsius)

I-Temp Product Name
(–40 to 149 degrees
Fahrenheit, –40 to +65
degrees Celsius)

A.4 Common Control Card Specifications

This section provides specifications for the TCC2, TCC2P, XCVT, XC10G, XC-VXC-10G, and AIC-I
cards.

For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance
Information document.

A.4.1 TCC2 Card Specifications

The TCC2 card has the following specifications:

• CTC software

–

Interface: EIA/TIA-232 (local craft access, on TCC2 faceplate)

–

Interface: 10BaseT LAN (on TCC2 faceplate)

–

Interface: 10BaseT LAN (through the backplane)

• Synchronization

–

Stratum 3, per Telcordia GR-253-CORE

–

Free running access: Accuracy +/– 4.6 ppm

–

Holdover stability: 3.7 * 10 exp – 7 per day including temperature (< 255 slips in first 24 hours)

A-12

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

–

• Supply voltage monitoring

–

–

–

–

• Environmental

–

–

–

• Dimensions

–

–

–

A.4.2 TCC2P Card Specifications

Reference: External BITS, line, internal

Both supply voltage inputs are monitored.

Normal operation: –40.5 to –56.7 V

Undervoltage: Major alarm

Overvoltage: Major alarm

Operating temperature: –40 to +149 degrees Fahrenheit (–40 to +65 degrees Celsius)

Operating humidity: 5 to 95 percent, noncondensing

Power consumption: 26.00 W, 0.54 A at –48 V, 88.8 BTU/hr

Height: 12.650 in. (321.3 mm)

Width: 0.716 in. (18.2 mm)

Depth: 9.000 in. (228.6 mm)

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 1.5 lb (0.7 kg)

A.4.2 TCC2P Card Specifications

The TCC2P card has the following specifications:

• CTC software

–

Interface: EIA/TIA-232 (local craft access, on TCC2P faceplate)

–

Interface: 10BaseT LAN (on TCC2P faceplate)

–

Interface: 10BaseT LAN (via backplane)

• Synchronization

–

Stratum 3, per Telcordia GR-253-CORE

–

Free running access: Accuracy +/– 4.6 ppm

–

Holdover stability: 3.7 * 10 exp – 7 per day including temperature (< 255 slips in first 24 hours)

–

Reference: External BITS, line, internal

• Supply voltage monitoring

–

Both supply voltage inputs are monitored.

–

Normal operation: –40.5 to –56.7 V (in –48 VDC systems)

April 2008

–

Undervoltage: Major alarm

–

Overvoltage: Major alarm

• Environmental

–

Operating temperature: –40 to +149 degrees Fahrenheit (–40 to +65 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 26.00 W, 0.54 A at –48 V, 88.8 BTU/hr

Cisco ONS 15454 Reference Manual, R8.0

A-13

A.4.3 XCVT Card Specifications

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 1.5 lb (0.7 kg)

A.4.3 XCVT Card Specifications

The XCVT card has the following specifications:

• Environmental

–

Operating temperature:

C-Temp (15454-XC-VT): 32 to 131 degrees Fahrenheit (0 to +55 degrees Celsius)

I-Temp (15454-XC-VT-T): –40 to 149 degrees Fahrenheit (–40 to +65 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

Appendix A Hardware Specifications

–

Power consumption: 34.40 W, 0.72 A, 117.46 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 1.9 lb (0.8 kg)

A.4.4 XC10G Card Specifications

The XC10G card has the following specifications:

• Environmental

–

Operating temperature:

C-Temp (15454-XC-10G): 32 to 131 degrees Fahrenheit (0 to +55 degrees Celsius)

–

Operating humidity: 5 to 85 percent, noncondensing

–

Power consumption: 48 W, 1.00 A, 163.68 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

A-14

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 1.5 lb (0.6 kg)

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

A.4.5 XC-XVC-10G Card Specifications

The XC-XVC-10G card has the following specifications:

• Environmental

–

Operating temperature:

I-Temp (15454-XC-VXC-10G-T): –40 to 149 degrees Fahrenheit (–40 to +65 degrees Celsius)

–

Operating humidity: 5 to 85 percent, noncondensing

–

Power consumption: 60 W, 1.25 A, 204.73 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 1.5 lb (0.6 kg)

A.4.5 XC-XVC-10G Card Specifications

A.4.6 AIC-I Card Specifications

The AIC-I card has the following specifications:

• Alarm inputs

–

Number of inputs: 12 without alarm extension panel (AEP), 32 with AEP

–

Opto coupler isolated

–

Label is customer provisionable.

–

Severity is customer provisionable.

–

Common 32 V output for all alarm inputs

–

Each input limited to 2 mA

–

Termination: Wire-wrap on backplane without AEP, on AEP connectors with AEP

• Alarm outputs

–

Number of outputs: 4 (user configurable as inputs) without AEP, 16 with AEP

–

Switched by opto MOS (metal oxide semiconductor)

–

Triggered by definable alarm condition

–

Maximum allowed open circuit voltage: 60 VDC

–

Maximum allowed closed circuit current: 100 mA

–

Termination: Wire-wrap on backplane without AEP, on AEP connectors with AEP

• Express orderwire/Local orderwire (EOW/LOW)

April 2008

–

ITU-T G.711, ITU-T G.712, Telcordia GR-253-CORE

–

A-law, mu-law

Note Due to the nature of mixed coding, in a mixed-mode configuration (A-law/mu-law) the

orderwire is not ITU-T G.712 compliant.

Cisco ONS 15454 Reference Manual, R8.0

A-15

A.4.7 AEP Specifications

–

Orderwire party line

–

Dual tone multifrequency (DTMF) signaling

• User data channel (UDC)

–

Bit rate: 64 kbps, bidirectional

–

ITU-T G.703

–

Input/output impedance: 120 ohm

–

Termination: RJ-11 connectors

• Data communications channel (DCC)

–

Bit rate: 576 kbps

–

EIA/TIA-485/V11

–

Input/output impedance: 120 ohm

–

Termination: RJ-45 connectors

• ACC connection for additional alarm interfaces

–

Connection to AEP

Appendix A Hardware Specifications

• Power monitoring alarming states:

–

Power failure (0 to –38 VDC)

–

Undervoltage (–38 to –40.5 VDC)

–

Overvoltage (beyond –56.7 VDC)

• Environmental

–

Operating temperature: –40 to 149 degrees Fahrenheit (–40 to +65 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption (including AEP, if used): 8.00 W, 0.17 A, 27.3 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 1.8 lb (0.82 kg)

A.4.7 AEP Specifications

The AEP has the following specifications:

• Alarm inputs

A-16

–

Number of inputs: 32

–

Optocoupler isolated

–

Label customer provisionable

–

Severity customer provisionable

–

Common 32 V output for all alarm inputs

–

Each input limited to 2 mA

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

–

• Alarm outputs

–

–

–

–

–

–

• Environmental

–

–

–

–

• Dimensions of AEP board

A.5 Electrical Card Specifications

Termination: 50-pin AMP champ connector

Number of outputs: 16

Switched by opto MOS

Triggered by definable alarm condition

Maximum allowed open circuit voltage: 60 VDC

Maximum allowed closed circuit current: 100 mA

Termination: 50-pin AMP champ connector

Overvoltage protection: as in ITU-T G.703 Annex B

Operating temperature: –40 to +65 degrees Celsius

Operating humidity: 5 to 95 percent, noncondensing

Power consumption: 3.00 W max., from +5 VDC from AIC-I, 10.2 BTU/hr max.

–

Height: 0.79 in. (20 mm)

–

Width: 13.0 in. (330 mm)

–

Depth: 3.5 in. (89 mm)

–

Weight: 0.4 lb (0.18 kg)

A.5 Electrical Card Specifications

This section provides specifications for the EC1-12, DS1-14, DS1N-14, DS1/E1-56, DS3/EC1-48,
DS3-12, DS3N-12, DS3i-N-12, DS3-12E, DS3N-12E, DS3XM-6, DS3XM-12, and filler cards.

For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance
Information document.

A.5.1 EC1-12 Card Specifications

The EC1-12 card has the following specifications:

• Input

–

Bit rate: 51.84 Mbps +/– 20 ppm

–

Frame format: SONET

–

Line code: B3ZS

–

Termination: Unbalanced coaxial cable

April 2008

–

Input impedance: 75 ohms +/– 5 percent

–

Cable loss: Max 450 feet 734A, RG-59, 728A/Max 79 feet RG-179

–

AIS: TR-TSY-000191 compliant

• Output

Cisco ONS 15454 Reference Manual, R8.0

A-17

A.5.2 DS1-14 and DS1N-14 Card Specifications

–

Bit rate: 51.84 Mbps +/– 20 ppm

–

Frame format: SONET

–

Line code: B3ZS

–

Termination: Unbalanced coaxial cable

–

Input impedance: 75 ohms +/–5 percent

–

Cable loss: Max 450 feet 734A, RG-59, 728A/Max 79 feet RG-179

–

AIS: TR-TSY-000191 compliant

–

Power level: –1.8 +/– 5.7 dBm

–

Pulse shape: ANSI T1.102-1988 Figure 8

–

Pulse amplitude: 0.36 to 0.85 V peak to peak

–

Loopback modes: Terminal and facility

–

Line build out: 0 to 225 feet (0 to 68.8 meters); 226 to 450 feet (68.9 to 137.2 meters)

• Electrical interface: BNC or SMB connectors

• Operating temperature

Appendix A Hardware Specifications

–

C-Temp (15454-EC1-12): 0 to 131 degrees Fahrenheit (0 to +55 degrees Celsius)

–

I-Temp (15454-EC1-12-T): –40 to 149 degrees Fahrenheit (–40 to +65 degrees Celsius)

Note The I-Temp symbol is displayed on the faceplate of an I-Temp compliant card. A card

without this symbol is C-Temp compliant.

• Operating humidity: 5 to 95 percent, noncondensing

• Power consumption: 36.60 W, 0.76 A, 124.97 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 2.0 lb (0.9 kg)

A.5.2 DS1-14 and DS1N-14 Card Specifications

The DS1-14 and DS1N-14 cards have the following specifications:

• Input

–

Bit rate: 1.544 Mbps +/– 32 ppm

–

Frame format: Off, SF (D4), ESF

–

Line code: AMI, B8ZS

A-18

–

Termination: Wire-wrap, AMP Champ

–

Input impedance: 100 ohms

–

Cable loss: Max 655 feet ABAM #22 AWG

–

AIS: TR-TSY-000191 compliant

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

• Output

–

–

–

–

–

–

–

–

–

–

–

• Electrical interface: BNC or SMB connectors

• Surge protection: Telcordia GR-1089

A.5.3 DS1/E1-56 Card Specifications

Bit rate: 1.544 Mbps +/– 32 ppm

Frame format: Off, SF (D4), ESF

Line code: AMI, B8ZS

Termination: Wire-wrap, AMP Champ

Input impedance: 100 ohms

Cable loss: Max 655 feet ABAM #22 AWG

AIS: TR-TSY-000191 compliant

Power level: 12.5 to 17.9 dBm centered at 772 KHz, –16.4 to –11.1 dBm centered at 1544 KHz

Pulse shape: Telcordia GR-499-CORE Figure 9-5

Pulse amplitude: 2.4 to 3.6 V peak-to-peak

Loopback modes: Terminal and facility

• Operating temperature

–

C-Temp (15454-DS1-14 and 15454-DS1N-14): 0 to 131 degrees Fahrenheit (0 to
+55 degrees Celsius)

–

I-Temp (15454-DS1-14-T and 15454-DS1N-14-T): –40 to 149 degrees Fahrenheit (–40 to
+65 degrees Celsius)

Note The I-Temp symbol is displayed on the faceplate of an I-Temp compliant card. A card

without this symbol is C-Temp compliant.

• Operating humidity: 5 to 95 percent, noncondensing

• Power consumption: 12.60 W, 0.26 A, 43.02 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 1.8 lb (0.8 kg)

A.5.3 DS1/E1-56 Card Specifications

April 2008

The DS1/E1-56 card has the following specifications:

The DS1/E1-56 card has the following specifications:

• Input

–

Bit rate: 1.544 Mbps ± 32 ppm (DS-1); 2.048 Mbps ±50ppm (E1)

–

Frame format: Off, SF (D4), ESF (DS-1); E1 multiframe, E1 CRC multiframe, and
unframed (ITU) (E1)

Cisco ONS 15454 Reference Manual, R8.0

A-19

A.5.4 DS3/EC1-48 Card Specifications

–

Line code: AMI, B8ZS (DS-1); HDB3 (E1)

–

Termination: Balanced, twisted pair, #22/24 AWG

–

Input impedance: 100 ohms +/– 5 percent (DS1); 120 ohms =/–5% (E1)

–

Cable loss: Max 655 feet ABAM #22/24 AWG (DS1); Compliant per ITU-T G.703 (E1)

–

AIS: TR-TSY-000191 compliant

• Output

–

Bit rate: 1.544 Mbps ± 32 ppm (DS-1); 2.048 Mbps ±50ppm (E1)

–

Frame format: Off, SF (D4), ESF (DS-1); E1 multiframe, E1 CRC multiframe, and
unframed (ITU) (E1)

–

Line code: AMI, B8ZS (DS-1); HDB3 (E1)

–

Termination: Balanced, twisted pair, #22/24 AWG

–

Input impedance: 100 ohms +/– 5 percent (DS1); 120 ohms =/–5% (E1)

–

Cable loss: Max 655 feet ABAM #22/24 AWG (DS1); Compliant per ITU-T G.703 (E1)

–

AIS: TR-TSY-000191 compliant

–

Power level: 12.6 to 17.9 dBm centered at 772 KHz

Appendix A Hardware Specifications

–

Pulse shape: Telcordia GR-499-CORE Figure 9-5 (DS-1); ITU-T G.703, Figure 15 (E1)

–

Pulse amplitude: 2.4 to 3.6 V peak-to-peak (DS-1); 2.7 to 3.3 V peak-to-peak (E1)

–

Loopback modes: Terminal and facility

• Electrical interface: SCSI (UBIC) connectors. UBIC-H: DS-1 and E1; UBIC-V: DS-1 only.

• Surge protection: Telcordia GR-1089

• Operating temperature

–

I-Temp (15454-DS1E1-56):–40 to 149 degrees Fahrenheit (–40 to +65 degrees Celsius)

Note The I-Temp symbol is displayed on the faceplate of an I-Temp compliant card. A card

without this symbol is C-Temp compliant.

• Operating humidity: 5 to 95 percent, noncondensing

• Power consumption: 36.00 W, 0.76 A, 124.97 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 2.0 lb (0.9 kg)

A.5.4 DS3/EC1-48 Card Specifications

The DS3/EC1-48 card has the following specifications:

• Input

–

Bit rate: 44.736 Mbps +/– 20 ppm

Cisco ONS 15454 Reference Manual, R8.0

A-20

April 2008

Appendix A Hardware Specifications

–

–

–

–

–

–

• Output

–

–

–

–

–

–

–

A.5.5 DS3-12 and DS3N-12 Card Specifications

Frame format: DS-3 ANSI T1.107-1988

Line code: B3ZS

Termination: Unbalanced coaxial cable

Input impedance: 75 ohms +/–5 percent

Cable loss: Max 450 feet with 734A or 728A, Max 79 feet with RG-179

AIS: TR-TSY-000191 compliant

Bit rate: 44.736 Mbps +/– 20 ppm

Frame format: DS-3 ANSI T1.107-1988

Line code: B3ZS

Termination: Unbalanced coaxial cable

Input impedance: 75 ohms +/–5 percent

Cable loss: Max 900 feet with 734A or 728A cable, Max 79 feet with RG-179

AIS: TR-TSY-000191 compliant

–

Power level: –1.8 to +5.7 dBm

–

Pulse shape: ANSI T1.102-1988 Figure 8

–

Pulse amplitude: 0.36 to 0.85 V peak

–

Loopback modes: Terminal and facility

–

Line build out: 0 to 225 feet (0 to 68.8 meters); 226 to 450 feet (68.9 to 137.2 meters)

• Electrical interface: BNC or SMB connectors

• Surge protection: Telcordia GR-1089

• Operating temperature:

–

I-Temp (15454-DS3_EC1-48): –40 to 149 degrees Fahrenheit (–40 to +65 degrees Celsius)

Note The I-Temp symbol is displayed on the faceplate of an I-Temp compliant card. A card

without this symbol is C-Temp compliant.

• Operating humidity: 5 to 95 percent, noncondensing

• Power consumption: 28W, 0.58 A at –48 V, 95.6 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Weight: 1.7 lb (0.7 kg)

A.5.5 DS3-12 and DS3N-12 Card Specifications

The DS3-12 and DS3N-12 cards have the following specifications:

• Input

April 2008

Cisco ONS 15454 Reference Manual, R8.0

A-21

A.5.5 DS3-12 and DS3N-12 Card Specifications

–

Bit rate: 44.736 Mbps +/– 20 ppm

–

Frame format: DS-3 ANSI T1.107-1988

–

Line code: B3ZS

–

Termination: Unbalanced coaxial cable

–

Input impedance: 75 ohms +/–5 percent

–

Cable loss: Max 450 feet 734A, RG-59, 728A/Max 79 feet RG-179

–

AIS: TR-TSY-000191 compliant

• Output

–

Bit rate: 44.736 Mbps +/– 20 ppm

–

Frame format: DS-3 ANSI T1.107-1988

–

Line code: B3ZS

–

Termination: Unbalanced coaxial cable

–

Input impedance: 75 ohms +/–5 percent

–

Cable loss: Max 450 feet 734A, RG-59, 728A/Max 79 feet RG-179

Appendix A Hardware Specifications

–

AIS: TR-TSY-000191 compliant

–

Power level: –1.8 to +5.7 dBm

–

Pulse shape: ANSI T1.102-1988 Figure 8

–

Pulse amplitude: 0.36 to 0.85 V peak-to-peak

–

Loopback modes: Terminal and facility

–

Line build out: 0 to 225 feet (0 to 68.8 meters); 226 to 450 feet (68.9 to 137.2 meters)

• Electrical interface: BNC or SMB connectors

• Surge protection: Telcordia GR-1089

• Operating temperature

C-Temp (15454-DS3-12 and 15454-DS3N-12): 0 to 131 degrees Fahrenheit (0 to
+55 degrees Celsius)

–

I-Temp (15454-DS3-12-T and 15454-DS3N-12-T): –40 to 149 degrees Fahrenheit (–40 to
+65 degrees Celsius)

Note The I-Temp symbol is displayed on the faceplate of an I-Temp compliant card. A card

without this symbol is C-Temp compliant.

• Operating humidity: 5 to 95 percent, noncondensing

• Power consumption: 38.20 W, 0.79 A, 130.43 BTU/hr

A-22

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

DS3-12 card weight: 1.7 lb (0.7 kg)

–

DS3N-12 card weight: 1.8 lb (0.8 kg)

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

A.5.6 DS3i-N-12 Card Specifications

The DS3i-N-12 card has the following specifications:

• Input

–

Bit rate: 44.736 Mbps +/–20 ppm

–

Frame format: ITU-T G.704, ITU-T G.752/DS-3 ANSI T1.107-1988

–

Line code: B3ZS

–

Termination: Unbalanced coaxial cable

–

Input impedance: 75 ohms +/– 5 percent

–

Cable loss:
Maximum 137 m (450 ft): 734A, RG59, 728A
Maximum 24 m (79 ft): RG179

–

AIS: ITU-T G.704 compliant

• Output

–

Bit rate: 44.736 Mbps +/– 20 ppm

–

Frame format: ITU-T G.704, ITU-T G.752/DS-3 ANSI T1.107-1988

–

Line code: B3ZS

A.5.6 DS3i-N-12 Card Specifications

–

Termination: Unbalanced coaxial cable

–

Output impedance: 75 ohms +/–5 percent

–

AIS: ITU-T G.704 compliant

–

Power level: –1.8 to +5.7 dBm

Note The power level is for a signal of all ones and is measured at a center frequency of

22.368 MHz (3 +/–1 kHz) bandwidth.)

–

Pulse shape: ITU-T G.703, Figure 14/ANSI T1.102-1988, Figure 8

–

Pulse amplitude: 0.36 to 0.85 V peak-to-peak

–

Loopback modes: Terminal and facility

–

Line build out: 0 to 225 feet (0 to 68.8 meters); 226 to 450 feet (68.9 to 137.2 meters)

• Electrical interface connectors: SMB, BNC

• Environmental

–

Overvoltage protection: As in ITU-T G.703 Annex B

–

Operating temperature: +23 to +113 degrees Fahrenheit (–5 to +45 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 26.80 W, 0.56 A at –48 V, 91.5 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

April 2008

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

Cisco ONS 15454 Reference Manual, R8.0

A-23

A.5.7 DS3-12E and DS3N-12E Card Specifications

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 1.9 lb (0.8 kg)

A.5.7 DS3-12E and DS3N-12E Card Specifications

The DS3-12E and DS3N-12E cards have the following specifications:

• Input

–

Bit rate: 44.736 Mbps +/– 20 ppm

–

Frame format: DS-3 ANSI T1.107-1988

–

Line code: B3ZS

–

Termination: Unbalanced coaxial cable

–

Input impedance: 75 ohms +/–5 percent

–

Cable loss: Max 450 feet 734A, RG-59, 728A/Max 79 feet RG-179

–

AIS: TR-TSY-000191 compliant

• Output

Appendix A Hardware Specifications

–

Bit rate: 44.736 Mbps +/– 20 ppm

–

Frame format: DS-3 ANSI T1.107-1988

–

Line code: B3ZS

–

Termination: Unbalanced coaxial cable

–

Input impedance: 75 ohms +/–5 percent

–

Cable loss: Max 450 feet 734A, RG-59, 728A/Max 79 feet RG-179

–

AIS: TR-TSY-000191 compliant

–

Power level: –1.8 to +5.7 dBm

Note The power level is for a signal of all ones and is measured at a center frequency of

22.368 MHz (3 +/–1 kHz) bandwidth.

–

Pulse shape: ANSI T1.102-1988 Figure 8

–

Pulse amplitude: 0.36 to 0.85 V peak-to-peak

–

Loopback modes: Terminal and facility

–

Line build out: 0 to 225 feet (0 to 68.8 meters); 226 to 450 feet (68.9 to 137.2 meters)

• Electrical interface: Connectors: BNC or SMB

• Surge protection: Telcordia GR-1089

• Operating temperature: I-Temp (15454-DS3-12E-T and 15454-DS3N-12E-T): –40 to

149 degrees Fahrenheit (–40 to +65 degrees Celsius)

A-24

Note The I-Temp symbol is displayed on the faceplate of an I-Temp compliant card. A card

without this symbol is C-Temp compliant.

• Operating humidity: 5 to 95 percent, noncondensing

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

• Power consumption: 26.80 W, 0.56 A, 91.51 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Depth with backplane connector: 9.250 in. (235.0 mm)

–

DS3-12E card weight: 1.8 lb (0.8 kg)

–

DS3N-12E card weight: 1.9 lb (0.8 kg)

A.5.8 DS3XM-12 Card Specifications

The DS3XM-12 card has the following specifications:

• Input

–

Bit rate: 44.736 Mbps +/–20 ppm

–

Frame format: DS-3 ANSI T1.107-1988

A.5.8 DS3XM-12 Card Specifications

–

Line code: B3ZS

–

Termination: Unbalanced coaxial cable

–

Input impedance: 75 ohms +/–5 percent

–

Cable loss: Max 450 feet 734A, RG-59, 728A/Max 79 feet RG-179

–

AIS: TR-TSY-000191 compliant

• Output

–

Bit rate: 44.736 Mbps +/– 20 ppm

–

Frame format: DS-3 ANSI T1.107-1988

–

Line code: B3ZS

–

Termination: Unbalanced coaxial cable

–

Input impedance: 75 ohms +/–5 percent

–

Cable loss: Max 450 feet 734A, RG-59, 728A/Max 79 feet RG-179

–

AIS: TR-TSY-000191 compliant

–

Power level: –1.8 to +5.7 dBm

–

Pulse shape: ANSI T1.102-1988 Figure 8

–

Pulse amplitude: 0.36 to 0.85 V peak-to-peak

–

Loopback modes: Terminal and facility

–

Line build out: 0 to 225 feet (0 to 68.8 meters); 226 to 450 feet (68.9 to 137.2 meters)

• Interface: BNC, SMB, UBIC and MiniBNC connectors

• Surge protection: Telcordia GR-1089

April 2008

• Operating temperature:

–

I-Temp (15454-DS3XM-12): –40 to 149 degrees Fahrenheit (–40 to +65 degrees Celsius)

Cisco ONS 15454 Reference Manual, R8.0

A-25

A.5.9 DS3XM-6 Card Specifications

Note The I-Temp symbol is displayed on the faceplate of an I-Temp compliant card. A card

without this symbol is C-Temp compliant.

• Operating humidity: 5 to 95 percent, noncondensing

• Power consumption: 34 W, 0.71A at –48 V, 116.1 BTU/hr

• Dimensions

–

Height: 12.65 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.00 in. (228.6 mm)

–

Card weight: 1.8 lb (0.8 kg)

A.5.9 DS3XM-6 Card Specifications

The DS3XM-6 card has the following specifications:

Appendix A Hardware Specifications

• Input

–

Bit rate: 44.736 Mbps +/–20 ppm

–

Frame format: DS-3 ANSI T1.107-1988

–

Line code: B3ZS

–

Termination: Unbalanced coaxial cable

–

Input impedance: 75 ohms +/–5 percent

–

Cable loss: Max 450 feet 734A, RG-59, 728A/Max 79 feet RG-179

–

AIS: TR-TSY-000191 compliant

• Output

–

Bit rate: 44.736 Mbps +/– 20 ppm

–

Frame format: DS-3 ANSI T1.107-1988

–

Line code: B3ZS

–

Termination: Unbalanced coaxial cable

–

Input impedance: 75 ohms +/–5 percent

–

Cable loss: Max 450 feet 734A, RG-59, 728A/Max 79 feet RG-179

–

AIS: TR-TSY-000191 compliant

–

Power level: –1.8 to +5.7 dBm

–

Pulse shape: ANSI T1.102-1988 Figure 8

–

Pulse amplitude: 0.36 to 0.85 V peak-to-peak

–

Loopback modes: Terminal and facility

A-26

–

Line build out: 0 to 225 feet (0 to 68.8 meters); 226 to 450 feet (68.9 to 137.2 meters)

• Interface: BNC or SMB connectors

• Surge protection: Telcordia GR-1089

• Operating temperature:

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

–

C-Temp (15454-DS3XM-6): 0 to 131 degrees Fahrenheit (0 to +55 degrees Celsius)

–

I-Temp (15454-DS3XM-6-T): –40 to 149 degrees Fahrenheit (–40 to +65 degrees Celsius)

Note The I-Temp symbol is displayed on the faceplate of an I-Temp compliant card. A card

without this symbol is C-Temp compliant.

• Operating humidity: 5 to 95 percent, noncondensing

• Power consumption: 20 W, 0.42 A, 68 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 1.8 lb (0.8 kg)

A.5.10 FILLER Card Specifications

A.5.10 FILLER Card Specifications

The FILLER cards have the following specifications:

• Environmental

–

Operating temperature:

C-Temp: -40 to +149 degree Fahrenheit (-40 to +65 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 0.4 lb (0.19 kg)

A.6 Optical Card Specifications

This section provides specifications for the OC3 IR4/STM1 SH 1310 (four-port), OC3 IR/STM1 SH
1310-8 (eight-port), OC12 IR/STM4 SH 1310, OC12 LR/STM4 LH 1310, OC12 LR STM4 LH 1550,
OC12 IR/STM4 SH 1310-4 (four-port), OC48 IR 1310, OC48 LR 1550, OC48 IR/STM16 SH AS 1310,
OC48 LR/STM16 LH AS 1550, OC48 ELR 100 GHz, OC48 ELR 200 GHz, OC192 SR/STM64 IO 1310,
OC192 IR/STM64 SH 1550, OC192 LR/STM64 LH 1550, OC192 LR/STM64 LH ITU 15xx.xx,
15454_MRC-12 (12-port), MRC-2.5G-4, OC192SR1/STM64IO Short Reach, and OC192/STM64 Any
Reach cards.

For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance
Information.

April 2008

Cisco ONS 15454 Reference Manual, R8.0

A-27

A.6.1 OC3 IR 4/STM1 SH 1310 Card Specifications

A.6.1 OC3 IR 4/STM1 SH 1310 Card Specifications

The OC3 IR 4/STM1 SH 1310 card has the following specifications:

• Line

–

Bit rate: 155.52 Mbps

–

Code: Scrambled non-return to zero (NRZ)

–

Fiber: 1310-nm single-mode

–

Loopback modes: Terminal and facility

–

Connector: SC

–

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957

• Transmitter

–

Maximum transmitter output power: –8 dBm

–

Minimum transmitter output power: –15 dBm

–

Center wavelength: 1274 to 1356 nm

–

Nominal wavelength: 1310 nm

Appendix A Hardware Specifications

–

Transmitter: Fabry Perot (FP) laser

–

Extinction Ratio: 8.2 dB

–

Dispersion Ratio: 96 ps/nm

• Receiver

–

Maximum receiver level: –8 dBm at BER 1 * 10 exp – 12

–

Minimum receiver level: –28 dBm at BER 1 * 10 exp – 12

–

Receiver: InGaAs/InP photodetector

–

Link loss budget: 13 dB

–

Receiver input wavelength range: 1274 to 1356 nm

–

Jitter tolerance: Telcordia GR-253/ITU-T G.823 compliant

• Environmental

–

Operating temperature:

C-Temp (15454-OC34IR1310): +23 to +113 degrees Fahrenheit (–5 to +45 degrees Celsius)

I-Temp (15454-OC34I13-T): –40 to 149 degrees Fahrenheit (–40 to +65 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 19.20 W, 0.40 A at –48 V, 65.56 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

A-28

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 1.0 lb (0.4 kg)

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

A.6.2 OC3 IR/STM1SH 1310-8 Card Specifications

The OC3 IR/STM1SH 1310-8 card has the following specifications:

• Line

–

Bit rate: 155.52 Mbps

–

Code: Scrambled NRZ

–

Fiber: 1310-nm single-mode

–

Loopback modes: Terminal and facility

–

Connector: LC

–

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957

• Transmitter

–

Maximum transmitter output power: –8 dBm

–

Minimum transmitter output power: –15 dBm

–

Center wavelength: 1261 to 1360 nm

–

Nominal wavelength: 1310 nm

A.6.2 OC3 IR/STM1SH 1310-8 Card Specifications

–

Transmitter: Fabry Perot laser

–

Extinction ratio: 8.2 dB

–

Dispersion tolerance: 96 ps/nm

• Receiver

–

Maximum receiver level: –8 dBm at BER 1 * 10 exp – 12

–

Minimum receiver level: –28 dBm at BER 1 * 10 exp – 12

–

Receiver: InGaAs/InP photodetector

–

Link loss budget: 13 dB

–

Receiver input wavelength range: 1261 to 1360 nm

–

Jitter tolerance: Telcordia GR-253/ITU-T G.823 compliant

• Environmental

–

Operating temperature: +23 to +113 degrees Fahrenheit (–5 to +45 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 23.00 W, 0.48 A at –48 V, 78.5 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 1.0 lb (0.4 kg)

April 2008

Cisco ONS 15454 Reference Manual, R8.0

A-29

A.6.3 OC12 IR/STM4 SH 1310 Card Specifications

A.6.3 OC12 IR/STM4 SH 1310 Card Specifications

The OC12 IR/STM4 SH 1310 card has the following specifications:

• Line

–

Bit rate: 622.08 Mbps

–

Code: Scrambled NRZ

–

Fiber: 1310-nm single-mode

–

Loopback modes: Terminal and facility

–

Connectors: SC

–

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957

• Transmitter

–

Maximum transmitter output power: –8 dBm

–

Minimum transmitter output power: –15 dBm

–

Center wavelength: 1274 to 1356 nm

–

Nominal wavelength: 1310 nm

Appendix A Hardware Specifications

–

Transmitter: Fabry Perot laser

–

Extinction ratio: 8.2 dB

–

Dispersion tolerance: 96 ps/nm

• Receiver

–

Maximum receiver level: –8 dBm at BER 1 * 10 exp – 12

–

Minimum receiver level: –28 dBm at BER 1 * 10 exp – 12

–

Receiver: InGa As/InP photodetector

–

Link loss budget: 13 dB

–

Receiver input wavelength range: 1274 to 1356 nm

–

Jitter tolerance: Telcordia GR-253/ITU-T G.823 compliant

• Environmental

–

Operating temperature:

C-Temp (15454-OC121IR1310): +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

I-Temp (15454-OC121I13-T): –40 to +149 degrees Fahrenheit (–40 to +65 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 10.90 W, 0.23 A at –48 V, 37.22 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

A-30

–

Weight not including clam shell: 1.4 lb (0.6 kg)

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

A.6.4 OC12 LR/STM4 LH 1310 Card Specifications

The OC12 LR/STM4 LH 1310 card has the following specifications:

• Line

–

Bit rate: 622.08 Mbps

–

Code: Scrambled NRZ

–

Fiber: 1310-nm single-mode

–

Loopback modes: Terminal and facility

–

Connectors: SC

–

Compliance: Telcordia SONET, Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957

• Transmitter

–

Maximum transmitter output power: +2 dBm

–

Minimum transmitter output power: –3 dBm

–

Center wavelength: 1280 to 1335 nm

–

Nominal wavelength: 1310 nm

A.6.4 OC12 LR/STM4 LH 1310 Card Specifications

–

Transmitter: Distributed feedback (DFB) laser

–

Extinction ratio: 10 dB

–

Dispersion tolerance: 190 ps/nm

• Receiver

–

Maximum receiver level: –8 dBm at BER 1 * 10 exp – 12

–

Minimum receiver level: –28 dBm at BER 1 * 10 exp – 12

–

Receiver: InGaAs/InP photodetector

–

Link loss budget: 25 dB

–

Receiver input wavelength range: 1280 to 1335 nm

–

Jitter tolerance: Telcordia GR-253/ITU-T G.823 compliant

• Environmental

–

Operating temperature:

C-Temp (15454-OC121LR1310): +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

I-Temp (15454-OC121L13-T): –40 to +149 degrees Fahrenheit (–40 to +65 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 9.28 W, 0.25 A, 41 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

April 2008

–

Weight not including clam shell: 1.4 lb (0.6 kg)

Cisco ONS 15454 Reference Manual, R8.0

A-31

A.6.5 OC12 LR/STM4 LH 1550 Card Specifications

A.6.5 OC12 LR/STM4 LH 1550 Card Specifications

The OC12 LR/STM4 LH 1550 card has the following specifications:

• Line

–

Bit rate: 622.08 Mbps

–

Code: Scrambled NRZ

–

Fiber: 1550-nm single-mode

–

Loopback modes: Terminal and facility

–

Connectors: SC

–

Compliance: Telcordia SONET, Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957

• Transmitter

–

Maximum transmitter output power: +2 dBm

–

Minimum transmitter output power: –3 dBm

–

Center wavelength: 1480 to 1580 nm

–

Nominal wavelength: 1550 nm

Appendix A Hardware Specifications

–

Transmitter: DFB laser

–

Dispersion tolerance: 1440 ps/nm

• Receiver

–

Maximum receiver level: –8 dBm at BER 1 * 10 exp – 12

–

Minimum receiver level: –28 dBm at BER 1 * 10 exp – 12

–

Receiver: InGaAs/InP photodetector

–

Link loss budget: 25 dB

–

Receiver input wavelength range: 1480 to 1580 nm

–

Jitter tolerance: Telcordia GR-253/ITU-T G.823 compliant

• Environmental

–

Operating temperature:

C-Temp (15454-OC121LR1550): +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

I-Temp (15454-OC121L15-T): –40 to +149 degrees Fahrenheit (–40 to +65 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 9.28 W, 0.19 A, 31.68 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Weight not including clam shell: 1.4 lb (0.6 kg)

A-32

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

A.6.6 OC12 IR/STM4 SH 1310-4 Specifications

The OC12 IR/STM4 SH 1310-4 card has the following specifications:

• Line

–

Bit rate: 622.08 Mbps

–

Code: Scrambled NRZ

–

Fiber: 1310-nm single-mode

–

Loopback modes: Terminal and facility

–

Connector: SC

–

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957

• Transmitter

–

Maximum transmitter output power: –8 dBm

–

Minimum transmitter output power: –15 dBm

–

Center wavelength: 1274 to 1356 nm

–

Nominal wavelength: 1310 nm

A.6.6 OC12 IR/STM4 SH 1310-4 Specifications

–

Transmitter: Fabry Perot laser

–

Extinction ratio: 10 dB

–

Dispersion tolerance: 190 ps/nm

• Receiver

–

Maximum receiver level: –8 dBm

–

Minimum receiver level: –30 dBm

–

Receiver: InGaAs/InP photodetector

–

Link loss budget: 15 dB

–

Receiver input wavelength range: 1274 to 1356 nm

–

Jitter tolerance: Telcordia GR-253/ITU-T G.823 compliant

• Operating temperature

–

C-Temp: +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

• Operating humidity

–

5 to 95 percent, noncondensing

• Power consumption

–

28 W, 0.58 A, 100 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

April 2008

–

Weight not including clam shell: 1.0 lb (0.4 kg)

Cisco ONS 15454 Reference Manual, R8.0

A-33

A.6.7 OC48 IR 1310 Card Specifications

Note Minimum transmit power, minimum receive power, and link loss budget might exceed standard

specifications.

A.6.7 OC48 IR 1310 Card Specifications

The OC48 IR 1310 card has the following specifications:

• Line

–

Bit rate: 2.49 Gbps

–

Code: Scrambled NRZ

–

Fiber: 1310-nm single-mode

–

Loopback modes: Terminal and facility

–

Connectors: SC

–

Compliance: Telcordia GR-253-CORE

• Transmitter

Appendix A Hardware Specifications

–

Maximum transmitter output power: 0 dBm

–

Minimum transmitter output power: –5 dBm

–

Center wavelength: 1280 to 1350 nm

–

Nominal wavelength: 1310 nm

–

Transmitter: Uncooled direct modulated DFB

• Receiver

–

Maximum receiver level: 0 dBm

–

Minimum receiver level: –18 dBm

–

Receiver: InGaAs InP photodetector

–

Link loss budget: 13 dB minimum

–

Receiver input wavelength range: 1280 to 1350 nm

• Environmental

–

Operating temperature:

C-Temp (15454-OC481IR1310): +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 32.20 W, 0.67 A, 109.94 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

A-34

–

Weight not including clam shell: 1.8 lb (0.8 kg)

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

A.6.8 OC48 LR 1550 Card Specifications

The OC48 LR 1550 card has the following specifications:

• Line

–

Bit rate: 2.49 Gbps

–

Code: Scrambled NRZ

–

Fiber: 1550-nm single-mode

–

Loopback modes: Terminal and facility

–

Connectors: SC

–

Compliance: Telcordia GR-253-CORE

• Transmitter

–

Maximum transmitter output power: +3 dBm

–

Minimum transmitter output power: –2 dBm

–

Center wavelength: 1520 to 1580 nm

–

Nominal wavelength: 1550 nm

A.6.8 OC48 LR 1550 Card Specifications

–

Transmitter: DFB laser

• Receiver

–

Maximum receiver level: –8 dBm

–

Minimum receiver level: –28 dBm

–

Receiver: InGaAs avalanche photo diode (APD) photodetector

–

Link loss budget: 26 dB minimum, with 1 dB dispersion penalty

–

Receiver input wavelength range: 1520 to 1580 nm

• Environmental

–

Operating temperature:

C-Temp (15454-OC481LR1550): +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 26.80 W, 0.56 A, 91.50 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Weight not including clam shell: 1.8 lb (0.8 kg)

A.6.9 OC48 IR/STM16 SH AS 1310 Card Specifications

The OC48 IR/STM16 SH AS 1310 card has the following specifications:

• Line

–

Bit rate: 2.49 Gbps

Cisco ONS 15454 Reference Manual, R8.0

April 2008

A-35

A.6.10 OC48 LR/STM16 LH AS 1550 Card Specifications

–

Code: Scrambled NRZ

–

Fiber: 1310-nm single-mode

–

Loopback modes: Terminal and facility

–

Connectors: SC

–

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957

• Transmitter

–

Maximum transmitter output power: 0 dBm

–

Minimum transmitter output power: –5 dBm

–

Center wavelength: 1280 to 1350 nm

–

Nominal wavelength: 1310 nm

–

Transmitter: DFB laser

–

Dispersion tolerance: 96 ps/nm

• Receiver

–

Maximum receiver level: 0 dBm

Appendix A Hardware Specifications

–

Minimum receiver level: –18 dBm

–

Receiver: InGaAs InP photodetector

–

Link loss budget: 13 dB minimum

–

Receiver input wavelength range: 1280 to 1350 nm

–

Jitter tolerance: Telcordia GR-253/ITU-T G.823 compliant

• Environmental

–

Operating temperature:

C-Temp (15454-OC481IR1310A): +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 37.20 W, 0.77 A, 127.01 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Weight not including clam shell: 2.2 lb (0.9 kg)

A.6.10 OC48 LR/STM16 LH AS 1550 Card Specifications

A-36

The OC48 LR/STM16 SH AS 1550 card has the following specifications:

• Line

–

Bit rate: 2.49 Gbps

–

Code: Scrambled NRZ

–

Fiber: 1550-nm single-mode

–

Loopback modes: Terminal and facility

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

–

–

• Transmitter

–

–

–

–

–

–

• Receiver

–

–

–

–

A.6.11 OC48 ELR/STM 16 EH 100 GHz Card Specifications

Connectors: SC

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957

Maximum transmitter output power: +3 dBm

Minimum transmitter output power: –2 dBm

Center wavelength: 1520 to 1580 nm

Nominal wavelength: 1550 nm

Transmitter: DFB laser

Dispersion ratio: 3600 ps/nm

Maximum receiver level: –8 dBm

Minimum receiver level: –28 dBm

Receiver: InGaAs APD photodetector

Link loss budget: 26 dB minimum, with 1 dB dispersion penalty

–

Receiver input wavelength range: 1520 to 1580 nm

–

Jitter tolerance: Telcordia GR-253/ITU-T G.823 compliant

• Environmental

–

Operating temperature:

C-Temp (15454-OC481LR1550A): +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 37.20 W, 0.77 A, 127.01 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Weight not including clam shell: 2.2 lb (0.9 kg)

A.6.11 OC48 ELR/STM 16 EH 100 GHz Card Specifications

The OC48 ELR 100 GHz card has the following specifications:

• Line

–

Bit rate: 2.49 Gbps

April 2008

–

Code: Scrambled NRZ

–

Fiber: 1550-nm single-mode

–

Loopback modes: Terminal and facility

–

Connectors: SC

–

Compliance: Telcordia GR-253-CORE, ITU-T G.692, ITU-T G.958

Cisco ONS 15454 Reference Manual, R8.0

A-37

A.6.12 OC48 ELR 200 GHz Card Specifications

• Transmitter

–

Maximum transmitter output power: 0 dBm

–

Minimum transmitter output power: –2 dBm

–

Center wavelength accuracy: +/– 0.12 nm

–

Transmitter: Electro-absorption laser

–

Dispersion tolerance: 5400 ps/nm

• Receiver

–

Maximum receiver level: –9 dBm

–

Minimum receiver level: –27 dBm at 1E–12 BER

–

Receiver: InGaAs APD photodetector

–

Link loss budget: 25 dB minimum at 1E–12 BER (not including the power dispersion penalty)

–

Dispersion penalty: 2 dB for a dispersion of up to 5400 ps/nm

–

Receiver input wavelength range: 1520 to 1580 nm

–

Jitter tolerance: Telcordia GR-253/ITU-T G.823 compliant

Appendix A Hardware Specifications

• Environmental

–

Operating temperature: C-Temp: +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 31.20 W, 0.65 A, 106.53 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Weight not including clam shell: 2.4 lb (1.1 kg)

A.6.12 OC48 ELR 200 GHz Card Specifications

The OC48 ELR 200 GHz card has the following specifications:

• Line

–

Bit rate: 2.49 Gbps

–

Code: Scrambled NRZ

–

Fiber: 1550-nm single-mode

–

Loopback modes: Terminal and facility

A-38

–

Connectors: SC

–

Compliance: Telcordia GR-253-CORE, ITU-T G692, ITU-T G958

• Transmitter

–

Maximum transmitter output power: 0 dBm

–

Minimum transmitter output power: –2 dBm

–

Center wavelength accuracy: +/– 0.25 nm

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

–

–

• Receiver

–

–

–

–

–

–

• Environmental

–

–

–

A.6.13 OC192 SR/STM64 IO 1310 Card Specifications

Transmitter: Electro-absorption laser

Dispersion tolerance: 3600 ps/nm

Maximum receiver level: –8 dBm

Minimum receiver level: –28 dBm

Receiver: InGaAs APD photodetector

Link loss budget: 26 dB minimum, with 1 dB dispersion penalty

Receiver input wavelength range: 1520 to 1580 nm

Jitter tolerance: Telcordia GR-253/ITU-T G.823 compliant

Operating temperature:

C-Temp: +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

Operating humidity: 5 to 95 percent, noncondensing

Power consumption: 31.20 W, 0.65 A, 106.53 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Weight not including clam shell: 2.9 lb (1.3 kg)

A.6.13 OC192 SR/STM64 IO 1310 Card Specifications

The OC192 SR/STM64 IO 1310 card has the following specifications:

• Line

–

Bit rate: 9.95328 Gbps

–

Code: Scrambled NRZ

–

Fiber: 1310-nm single-mode

–

Maximum chromatic dispersion allowance: 6.6 ps/nm

–

Loopback modes: Terminal and facility

–

Connectors: SC

–

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, ITU-T G.691

• Transmitter

April 2008

–

Maximum transmitter output power: –1 dBm

–

Minimum transmitter output power: –6 dBm

–

Center wavelength: 1290 to 1330 nm

–

Nominal wavelength: 1310 nm

–

Transmitter: Directly modulated laser

• Receiver

Cisco ONS 15454 Reference Manual, R8.0

A-39

A.6.14 OC192 IR/STM64 SH 1550 Card Specifications

–

Maximum receiver level: –1 dBm at BER 1 * 10 exp – 12

–

Minimum receiver level: –11 dBm at BER 1 * 10 exp – 12

–

Receiver: PIN diode

–

Link loss budget: 5 dB minimum, plus 1 dB dispersion penalty
at BER = 1 * 10 exp – 12 including dispersion

–

Receiver input wavelength range: 1290 to 1330 nm

–

Dispersion tolerance: 6.6 ps/nm

• Environmental

–

Operating temperature: +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 47.00 W, 0.98 A at –48 V, 160.5 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

Appendix A Hardware Specifications

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 3.1 lb (1.3 kg)

A.6.14 OC192 IR/STM64 SH 1550 Card Specifications

The OC192 IR/STM64 SH 1550 card has the following specifications:

• Line

–

Bit rate: 9.95328 Gbps

–

Code: Scrambled NRZ

–

Fiber: 1550-nm single-mode

–

Maximum chromatic dispersion allowance: 800 ps/nm

–

Loopback modes: Terminal and facility

Note You must use a 3 to 15 dB fiber attenuator (5 dB recommended) when working with the

OC192 IR/STM64 SH 1550 card in a loopback. Do not use fiber loopbacks with the
OC192 IR/STM64 SH 1550 card. Using fiber loopbacks can cause irreparable damage to the
OC192 IR/STM64 SH 1550 card.

–

Connectors: SC

–

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, ITU-T G.691

A-40

• Transmitter

–

Maximum transmitter output power: +2 dBm

–

Minimum transmitter output power: –1 dBm

–

Center wavelength: 1530 to 1565 nm

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

–

–

• Receiver

–

–

–

–

–

–

• Environmental

–

–

–

• Dimensions

A.6.15 OC192 LR/STM64 LH 1550 Card Specifications

Nominal wavelength: 1550 nm

Transmitter: Cooled EA (European accreditation) modulated laser

Maximum receiver level: –1 dBm at BER 1 * 10 exp – 12

Minimum receiver level: –14 dBm at BER 1 * 10 exp – 12

Receiver: PIN diode

Link loss budget: 13 dB minimum, plus 2 dB dispersion penalty
at BER = 1 * 10 exp – 12 including dispersion

Receiver input wavelength range: 1530 to 1565 nm

Dispersion tolerance: 800 ps/nm

Operating temperature: +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

Operating humidity: 5 to 95 percent, noncondensing

Power consumption: 50.00 W, 1.04 A at –48 V, 170.7 BTU/hr

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 3.1 lb (1.3 kg)

A.6.15 OC192 LR/STM64 LH 1550 Card Specifications

The OC192 LR/STM64 LH 1550 card has the following specifications:

• Line

–

Bit rate: 9.95328 Gbps

–

Code: Scrambled NRZ

–

Fiber: 1550-nm single-mode

–

Loopback modes: Terminal and facility

Note You must use a fiber attenuator when connecting a fiber loopback to an OC192 LR/STM64 LH 1550

card. Use a 19 to 24 dB attenuator for 15454-OC192LR1550 or a 14 to 28 dB attenuator for
15454-OC192-LR2 (20 dB is recommended). Never connect a direct fiber loopback.

April 2008

–

Connectors: SC

–

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957

• Transmitter

–

Maximum transmitter output power:
+10 dBm (15454-OC192LR1550);
+7 dBm (15454-OC192-LR2)

Cisco ONS 15454 Reference Manual, R8.0

A-41

A.6.16 OC192 LR/STM64 LH ITU 15xx.xx Card Specifications

–

Minimum transmitter output power:
+7 dBm (15454-OC192LR1550);
+4 dBm (15454-OC192-LR2)

–

Center wavelength: 1530 to 1565 nm

–

Nominal wavelength: 1550 nm

–

Maximum chromatic dispersion allowed: 1600 ps/nm

–

Transmitter: LN (Lithium Niobate) external modulator transmitter

• Receiver

–

Maximum receiver level:
–10 dBm (15454-OC192LR1550);
–7 dBm (15454-OC192LR1550)

–

Minimum receiver level:
–19 dBm (15454-OC192LR1550);
–24 dBm from 1530 to 1565 nm
–20 dBm from 1290 to 1330 nm (15454-OC192-LR2)

–

Receiver: APD/TIA

–

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 – exp (–12) including dispersion

–

Receiver input wavelength range: 1530 to 1565 nm

Appendix A Hardware Specifications

–

Jitter tolerance: Telcordia GR-253/ITU-T G.823 compliant

• Environmental

–

Operating temperature:

C-Temp (15454-OC192LR1550): +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 72.20 W, 1.50 A, 246.52 BTU/hr (15454-OC192LR1550);

52.00 W, 1.08 A at –48 V, 177.6 BTU/hr (15454-OC192-LR2)

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Weight not including clam shell: 3.1 lb (1.3 kg)

A.6.16 OC192 LR/STM64 LH ITU 15xx.xx Card Specifications

The OC192 LR/STM64 LH ITU 15xx.xx card has the following specifications:

• Line

–

Bit rate: 9.95328 Gbps

–

Code: Scrambled NRZ

A-42

–

Fiber: 1550-nm single-mode

–

Maximum chromatic dispersion allowance:

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

–

Note You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the

–

–

• Transmitter

–

–

–

–

A.6.16 OC192 LR/STM64 LH ITU 15xx.xx Card Specifications

In deployments with a dispersion compensation unit (DCU): +/– 1000 ps/nm, with optical
signal-to-noise ration (OSNR) of 19 dB (0.5 nm resolution bandwidth [RBW])

In deployments without a DCU: +/– 1200 ps/nm, with OSNR of 23 dB (0.5 nm RBW)

Loopback modes: Terminal and facility

OC192 LR/STM64 LH 15xx.xx card in a loopback. Do not use fiber loopbacks with the
OC192 LR/STM64 LH 15xx.xx card. Using fiber loopbacks causes irreparable damage to
this card.

Connectors: SC

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.691, ITU-T G.957

Maximum transmitter output power: +6 dBm

Minimum transmitter output power: +3 dBm

Center wavelength: See wavelength plan

Center wavelength accuracy: +/– 0.040 nm

–

Transmitter: LN external modulator transmitter

• Receiver

–

Maximum receiver level: –8 dBm at BER 1 * 10 exp – 12

–

Minimum receiver level: –22 dBm at BER 1 * 10 exp – 12

–

Receiver: APD

–

Link loss budget: 25 dB minimum, plus 2 dB dispersion penalty
at BER = 1 * 10 exp – 12 including dispersion

–

Receiver input wavelength range: 1529 to 1565 nm

• Environmental

–

Operating temperature: +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 52.00 W, 1.08 A at –48 V, 177.6 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 3.1 lb (1.3 kg)

April 2008

• Currently available wavelengths and versions of OC192 LR/STM64 LH ITU 15xx.xx card:

ITU grid blue band:

–

1534.25 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1534.25

–

1535.04 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1535.04

Cisco ONS 15454 Reference Manual, R8.0

A-43

A.6.17 15454_MRC-12 Card Specifications

–

1535.82 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1535.82

–

1536.61 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1536.61

–

1538.19 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1538.19

–

1538.98 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1538.98

–

1539.77 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1539.77

–

1540.56 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1540.56

ITU grid red band:

–

1550.12 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1550.12

–

1550.92 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1550.92

–

1551.72 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1551.72

–

1552.52 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1552.52

–

1554.13 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1554.13

–

1554.94 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1554.94

–

1555.75 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1555.75

Appendix A Hardware Specifications

–

1556.55 +/– 0.040 nm, OC192 LR/STM64 LH ITU 1556.55

A.6.17 15454_MRC-12 Card Specifications

The 15454_MRC-12 card has the following specifications:

• Line

–

Bit rate: up to OC-48 (2488.320 Mbps), depending on SFP

Note Each optical interface on the card can be configured as OC-3, OC-12, or OC-48, depending

on the available backplane bandwidth and existing provisioned lines. In general, the card
supports all different rates on the line side as long as the accumulated bandwidth does not
exceed the total backplane allowed bandwidth.

–

Fiber: 1550-nm single-mode

–

Connectors: LC duplex connector for each SFP

–

Compliance: Telcordia GR-253-CORE

• Transmitter

–

Maximum transmitter output power: Depends on SFP (see A.2 SFP, XFP, and GBIC

Specifications, page A-4)

–

Minimum transmitter output power: Depends on SFP (see A.2 SFP, XFP, and GBIC

Specifications, page A-4)

–

Center wavelength: See wavelength plan

A-44

–

Center wavelength accuracy: 1 nm to 4 nm, depending on SFP

–

Transmitter: FP and DFB laser

• Receiver

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

–

–

–

–

• Environmental

–

–

–

• Dimensions

–

–

–

–

–

A.6.18 MRC-2.5G-4 Card Specifications

Maximum receiver level: Depends on SFP (see A.2 SFP, XFP, and GBIC Specifications,

page A-4)

Minimum receiver level: Depends on SFP (see A.2 SFP, XFP, and GBIC Specifications,

page A-4)

Receiver: PIN PD

Receiver input wavelength range: Depends on SFP

Operating temperature: –40 to +149 degrees Fahrenheit (–40 to +65 degrees Celsius)

Operating humidity: 5 to 95 percent, noncondensing

Power consumption: 38.00 W, 0.79 A at –48 V, 129.66 BTU/hr

Height: 12.650 in. (321.3 mm)

Width: 0.716 in. (18.2 mm)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

• Wavelength plan. Currently available wavelengths and versions of the 15454_MRC-12 card:

–

For ONS-SC-2G-30.3 through ONS-SC-2G-60.0 SFPs: 1530.33 nm to 1560.61 nm
(32 distinct wavelengths at 100 GHz spacing)

–

For ONS-SE-622-1470 through ONS-SE-622-1610 SFPs: 1470 to 1610 nm
(eight distinct wavelengths at 2500 GHz spacing)

–

For ONS_SE-155-1470 through ONS-SE-155-1610 SFPs: 1470 to 1610 nm
(eight distinct wavelengths at 2500 GHz spacing)

A.6.18 MRC-2.5G-4 Card Specifications

The MRC-2.5G-4 card has the following specifications:

• Line

–

Bit rate: up to OC-48 (2488.320 Mbps), depending on SFP

Note Each optical interface on the card can be configured as OC-3, OC-12, or OC-48, depending

on the available backplane bandwidth and existing provisioned lines. In general, the card
supports all different rates on the line side as long as the accumulated bandwidth does not
exceed the total backplane allowed bandwidth.

–

Fiber: 1550-nm single-mode

April 2008

–

Connectors: LC duplex connector for each SFP

–

Compliance: Telcordia GR-253-CORE

• Transmitter

–

Maximum transmitter output power: Depends on SFP (see A.2 SFP, XFP, and GBIC

Specifications, page A-4)

Cisco ONS 15454 Reference Manual, R8.0

A-45

A.6.19 OC192SR1/STM64IO Short Reach Card Specifications

–

Minimum transmitter output power: Depends on SFP (see A.2 SFP, XFP, and GBIC

Specifications, page A-4)

–

Center wavelength: See wavelength plan

–

Center wavelength accuracy: 1 nm to 4 nm, depending on SFP

–

Transmitter: FP and DFB laser

• Receiver

–

Maximum receiver level: Depends on SFP (see A.2 SFP, XFP, and GBIC Specifications,

page A-4)

–

Minimum receiver level: Depends on SFP (see A.2 SFP, XFP, and GBIC Specifications,

page A-4)

–

Receiver: PIN PD

–

Receiver input wavelength range: Depends on SFP

• Environmental

–

Operating temperature: –40 to +149 degrees Fahrenheit (–40 to +65 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 38.00 W, 0.79 A at –48 V, 129.66 BTU/hr

• Dimensions

Appendix A Hardware Specifications

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 3.1 lb (1.3 kg)

• Wavelength plan. Currently available wavelengths and versions of the MRC-2.5G-4 card:

–

For ONS-SC-2G-30.3 through ONS-SC-2G-60.0 SFPs: 1530.33 nm to 1560.61 nm
(32 distinct wavelengths at 100 GHz spacing)

–

For ONS-SE-622-1470 through ONS-SE-622-1610 SFPs: 1470 to 1610 nm
(eight distinct wavelengths at 2500 GHz spacing)

–

For ONS_SE-155-1470 through ONS-SE-155-1610 SFPs: 1470 to 1610 nm
(eight distinct wavelengths at 2500 GHz spacing)

A.6.19 OC192SR1/STM64IO Short Reach Card Specifications

Note The OC192SR1/STM64IO Short Reach card is designated as OC192-XFP in CTC.

The OC192SR1/STM64IO Short Reach card has the following specifications:

• Line

A-46

–

Bit rate: OC-192 (9.9520 Gbps)

–

Fiber: 1310-nm single-mode

–

Connectors: LC duplex connector for the XFP

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

–

• Transmitter

–

–

• Receiver

–

–

–

• Environmental

–

–

–

• Dimensions

–

A.6.20 OC192/STM64 Any Reach Card Specifications

Compliance: Telcordia GR-253-CORE

Maximum transmitter output power: –1 dBm

Minimum transmitter output power: –6 dBm

Maximum receiver level: –1 dBm

Minimum receiver level: –11 dBm

Receiver input wavelength range: 1260 to 1565 nm

Operating temperature: 32 to +131 degrees Fahrenheit (0 to +55 degrees Celsius)

Operating humidity: 5 to 95 percent, noncondensing

Power consumption: 40.00 W, 0.83 A at –48 V, 136.49 BTU/hr

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 3.1 lb (1.3 kg)

A.6.20 OC192/STM64 Any Reach Card Specifications

Note The OC192/STM64 Any Reach card is designated as OC192-XFP in CTC.

The OC192/STM64 Any Reach card has the following specifications:

• Line

–

Bit rate: OC-192 (9.9520 Gbps)

–

Fiber: 1310-nm single-mode for ONS-XC-10G-S1 XFP, 1550-nm single mode for
ONS-XC-10G-I2 and ONS-XC-10G-L2 XFPs

–

Connectors: LC duplex connector for the XFPs

–

Compliance: Telcordia GR-253-CORE

• Transmitter

–

Maximum transmitter output power: Depends on SFP (see A.2 SFP, XFP, and GBIC

Specifications, page A-4)

–

Minimum transmitter output power: Depends on SFP (see A.2 SFP, XFP, and GBIC

Specifications, page A-4)

• Receiver

April 2008

–

Maximum receiver level: Depends on SFP (see A.2 SFP, XFP, and GBIC Specifications,

page A-4)

Cisco ONS 15454 Reference Manual, R8.0

A-47

A.7 Ethernet Card Specifications

–

–

• Environmental

–

–

–

• Dimensions

–

–

–

–

–

Appendix A Hardware Specifications

Minimum receiver level: Depends on SFP (see A.2 SFP, XFP, and GBIC Specifications,

page A-4)

Receiver input wavelength range: 1260 to 1565 nm

Operating temperature: 32 to +131 degrees Fahrenheit (0 to +55 degrees Celsius)

Operating humidity: 5 to 95 percent, noncondensing

Power consumption: 40.00 W, 0.83 A at –48 V, 136.49 BTU/hr

Height: 12.650 in. (321.3 mm)

Width: 0.716 in. (18.2 mm)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

A.7 Ethernet Card Specifications

This section includes specifications for the E100T-12, E100T-G, E1000-2, E1000-2-G, CE-1000-4,
CE-100T-8, CE-MR-10, G1K-4, ML100T-12, ML1000-2, ML-MR-10, and ML100X-8 cards.

For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance
Information document.

A.7.1 E100T-12 Card Specifications

The E100T-12 card has the following specifications:

• Environmental

–

Operating temperature

C-Temp (15454-E100T): 32 to 131 degrees Fahrenheit (0 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 65 W, 1.35 A, 221.93 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 2.3 lb (1.0 kg)

A.7.2 E100T-G Card Specifications

The E100T-G card has the following specifications:

• Environmental

Cisco ONS 15454 Reference Manual, R8.0

A-48

April 2008

Appendix A Hardware Specifications

–

Operating temperature:

C-Temp (15454-E100T-G): 32 to 131 degrees Fahrenheit (0 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 65 W, 1.35 A, 221.93 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 2.3 lb (1.0 kg)

A.7.3 E1000-2 Card Specifications

The E1000-2 card has the following specifications:

• Environmental

–

Operating temperature:

A.7.3 E1000-2 Card Specifications

C-Temp (15454-E1000-2): 32 to 131 degrees Fahrenheit (0 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 53.50 W, 1.11 A, 182.67 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 2.1 lb (0.9 kg)

A.7.4 E1000-2-G Card Specifications

The E1000-2-G card has the following specifications:

• Environmental

–

Operating temperature:

C-Temp (15454-E1000-2-G): 32 to 131 degrees Fahrenheit (0 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 53.50 W, 1.11 A, 182.67 BTU/hr

• Dimensions

April 2008

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 2.1 lb (0.9 kg)

Cisco ONS 15454 Reference Manual, R8.0

A-49

A.7.5 CE-1000-4 Card Specifications

A.7.5 CE-1000-4 Card Specifications

The CE-1000-4 card has the following specifications:

• Environmental

–

Operating temperature: +23 to +131 degrees Fahrenheit (-5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 60 W, 1.25 A at -48 V, 204.8 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.310 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 2.1 lb (0.9 kg)

A.7.6 CE-100T-8 Card Specifications

Appendix A Hardware Specifications

The CE-100T-8 card has the following specifications:

• Environmental

–

Operating temperature

C-Temp (15454-CE100T): 32 to 131 degrees Fahrenheit (0 to +55 degrees Celsius)

–

Operating humidity: 0 to 95 percent, noncondensing

–

Power consumption: 53 W, 1.1 A, 181.3 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.913 in. (23.19 mm)

–

Depth: 9.073 in. (230.45 mm)

–

Card weight: 1.8 lb (0.82 kg)

A.7.7 CE-MR-10 Card Specifications

The CE-MR-10 card has the following specifications:

• Environmental

–

Operating temperature

C-Temp (15454-CE-MR-10): 32 to 131 degrees Fahrenheit (0 to +50 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

A-50

–

Power consumption: 65 W, 1.35 A at -48 V, 221.93 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

–

Depth: 9.000 in. (228.6 mm)

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 2.3 lb (1.0 kg)

A.7.8 G1K-4 Card Specifications

The G1K-4 card has the following specifications:

• Environmental

–

Operating temperature: +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 63.00 W, 1.31 A at –48 V, 215.1 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

A.7.8 G1K-4 Card Specifications

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 2.1 lb (0.9 kg)

A.7.9 ML100T-12 Card Specifications

The ML100T-12 card has the following specifications:

• Environmental

–

Operating temperature: +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 53.00 W, 1.10 A at –48 V, 181.0 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 2.3 lb (1.0 kg)

A.7.10 ML1000-2 Card Specifications

April 2008

The ML1000-2 card has the following specifications:

• Environmental

–

Operating temperature: +23 to +131 degrees Fahrenheit (–5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

Cisco ONS 15454 Reference Manual, R8.0

A-51

A.7.11 ML100X-8 Card Specifications

–

Power consumption: 49.00 W, 1.02 A at –48 V, 167.3 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 0.9 kg (2.1 lb)

A.7.11 ML100X-8 Card Specifications

The ML100X-8 card has the following specifications:

• Environmental

–

Operating temperature: +23 to +131 degrees Fahrenheit (–40 to +65 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 65.00 W, 1.35 A at –48 V, 221.93 BTU/hr

Appendix A Hardware Specifications

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 0.9 kg (2.1 lb)

A.7.12 ML-MR-10 Card Specifications

The ML-MR-10 card has the following specifications:

• Environmental

–

Operating temperature: +23 to +131 degrees Fahrenheit (–40 to +65 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 65.00 W

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

A-52

–

Depth with backplane connector: 9.250 in. (235 mm)

–

Weight not including clam shell: 0.9 kg (2.1 lb)

Cisco ONS 15454 Reference Manual, R8.0

April 2008

Appendix A Hardware Specifications

A.8 Storage Access Networking Card Specifications

A.8 Storage Access Networking Card Specifications

This section describes the FC_MR-4 (Fibre Channel) card specifications.

For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance
Information document.

• Fibre Channel Support: FC-0 and FC-1 layers of ANSI X3.230 FC-PH

• GBIC Line Interface

–

Bit Rate: 1.0625 Gbit/s single-rate or 1.0625/2.125 dual-rate Gbit/s Fibre Channel (FC)

–

Wavelength/Fiber/Reach:

850 nm, multimode fiber, 550 m (SX)

1310 nm, single-mode fiber, 10 km (LX)

1550 nm/, single-mode fiber, 80 km (ZX)

–

Hot pluggable

–

Auto-detection

• Transmitter

–

Maximum transmitter output power: depends on GBIC type (see Table A-2 )

–

Minimum transmitter output power: depends on GBIC type (see Tabl e A -2)

• Receiver

–

Maximum receiver level: depends on GBIC type (see Tab le A-2)

–

Minimum receiver level: depends on GBIC type (see Tab l e A-2)

• Environmental

–

Operating temperature

C-Temp (15454-E100T): 23 to 131 degrees Fahrenheit (–5 to +55 degrees Celsius)

–

Operating humidity: 5 to 95 percent, noncondensing

–

Power consumption: 60 W, 1.35 A, 221.93 BTU/hr

• Dimensions

–

Height: 12.650 in. (321.3 mm)

–

Width: 0.716 in. (18.2 mm)

–

Depth: 9.000 in. (228.6 mm)

–

Card weight: 2.59 lb (1.17 kg)

April 2008

Cisco ONS 15454 Reference Manual, R8.0

A-53

A.8 Storage Access Networking Card Specifications

Appendix A Hardware Specifications

A-54

Cisco ONS 15454 Reference Manual, R8.0

April 2008