Cisco Systems MMDS CPE R1 Manual
Ripwave
2.6 GHz
User Guide
For Windows® 95 or later
Note: This User Guide is for Beta Users only. The contents are subject to change at any time during the Beta test.
Version 1.0.1 |
Part number 40-00026-00 |
Produce Release 1.13 |
Revision B |
Ripwave 2.6 GHz User Guide |
Navini Networks, Inc. |
i
Ripwave 2.6 GHz User Guide |
Navini Networks, Inc. |
TABLE OF CONTENTS
PERMISSIONS, TRADEMARKS, AND DISTRIBUTION....................................... |
VI |
REGULATORY INFORMATION ............................................................................. |
VII |
SAFETY........................................................................................................................ |
VIII |
INTRODUCTION............................................................................................................. |
1 |
RIPWAVE UNIT INSTALLATION............................................................................... |
2 |
USB connections................................................................................................................ |
2 |
Ethernet connections ........................................................................................................ |
7 |
RIPWAVE MONITOR SOFTWARE INSTALLATION............................................. |
9 |
ACCESSING THE INTERNET.................................................................................... |
14 |
RIPWAVE UNIT INDICATOR LIGHTS ................................................................... |
15 |
DISPLAYING THE RIPWAVE MONITOR............................................................... |
16 |
UNINSTALL RIPWAVE SOFTWARE....................................................................... |
19 |
INSTALLING / CHARGING THE BATTERY .......................................................... |
21 |
BETA USER GUIDE FREQUENTLY ASKED QUESTIONS.................................. |
23 |
END USER LICENSE AGREEMENT......................................................................... |
25 |
ii
Ripwave 2.6 GHz User Guide |
Navini Networks, Inc. |
iii
Ripwave 2.6 GHz User Guide |
Navini Networks, Inc. |
Symbols
Throughout this manual, the following symbols are used to designate precautions that need to be taken when performing the step. For your safety and protection of the equipment, observe these precautions when installing, operating, or servicing the equipment.
|
|
|
|
|
|
|
|
Caution |
This symbol indicates a potentially hazardous |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
situation that may result in equipment damage |
|
|
|
|
|
|
|
|
|
Symbol |
or improper operation. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Warning |
This symbol indicates a potentially hazardous |
|
|
|
|
|
|
|
|
situation that may result in death or injury to |
|
|
|
|
|
|
|
|
|
Symbol |
personnel. |
|
|
|
|
|
|
|
|
|
|
Notes
|
|
Notes |
This symbol indicates points, comments, or |
|
|
special attention that is required during a |
|
|
|
||
|
|
Symbol |
procedure. |
|
|
|
|
iv
Ripwave 2.6 GHz User Guide |
Navini Networks, Inc. |
v
Ripwave 2.6 GHz User Guide |
Navini Networks, Inc. |
Permissions, trademarks, and distribution
Copyright© November 2001 - 2002, Navini Networks, Inc. All information contained herein and disclosed by this document is confidential and the proprietary property of Navini Networks, Inc. and all rights therein are expressly reserved. Acceptance of this material signifies agreement by the recipient that the information contained in this document is confidential and that it will be used solely for the purposes set forth herein. Acceptance of this material signifies agreement by the recipient that it will not be used, reproduced in whole or in part, disclosed, distributed, or conveyed to others in any manner or by any means – graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems – without the express written permission of Navini Networks, Inc.
Navini Networks™, Internet at the Speed of Thought™, zero-install™, and Ripwave™ are registered trademarks of Navini Networks, Inc. Other product and company names mentioned herein may be trademarks and/or service marks of their respective owners.
Nothing herein constitutes any representation, warranty, assurance, or guaranty of any kind.
Because of continuing developments and improvements in design, manufacturing, and deployment, material in this document is subject to change without notification and does not represent any commitment or obligation on the part of Navini Networks, Inc.
Navini Networks, Inc. shall have no liability for any error or damages resulting from the use of this document.
The logo and all other Navini Networks trademarks are the property of Navini Networks, Inc. Unauthorized usage is strictly prohibited without the express written permission of Navini Networks, Inc.
2001 - 2002 Navini Networks, Inc. All rights reserved.
vi
Ripwave 2.6 GHz User Guide |
Navini Networks, Inc. |
Regulatory Information
Caution: This device is a radio frequency transmitter. It is required to comply with FCC RF exposure requirements for transmitting devices. A minimum separation distance of 8 inches (20 cm) or more must be maintained between the antenna and all persons during device operations to ensure compliance with the FCC’s rules for Radio Frequency Exposure. If this minimum distance cannot be maintained, exposure to RF levels that exceed the FCC’s limits may result. This equipment must not be co-located with any other transmitting antenna.
This equipment complies with part 21 of the FCC rules. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
vii
Ripwave 2.6 GHz User Guide |
Navini Networks, Inc. |
Safety
To optimize safety when using the Navini equipment, please read before using.
When using the Navini electronic equipment, always follow the basic safety precautions to reduce the risk of electrical shock, fire, and injury to people and/or property.
1.Follow all warnings and instructions that come with the equipment.
2.Do not use the equipment while you are in a bathtub, shower, pool, or spa. Exposure of the equipment to water could cause severe electrical shock (even death) or serious damage to the equipment.
3.Do not allow any type of liquid to come in contact with the equipment. Unplug the equipment from the power source before cleaning. Use a damp cloth for cleaning. Do not use any soaps or liquid cleaners.
4.Follow all airport and FAA regulations when using the equipment on or near aircraft.
5.Only operate the equipment from the type of power source(s) indicated in this manual (110 VAC or Navini supplied battery). Any other type of input power source may cause damage to the equipment.
6.Power the equipment using only the battery or the AC adapter cable provided, and in accordance with the instructions specified in the user manual.
7.Do not use a frayed or damaged power cord. Do not place the power cord where it can be stepped on or tripped over.
8.Do not touch wires where the insulation is frayed or worn unless the equipment has been disconnected from its power source.
9.Do not overload wall outlets, power strips, or extension cords. This can cause serious electrical shock or fire.
10.Do not place the equipment on an unstable surface. It can fall and cause injury or damage to the equipment.
viii
Ripwave 2.6 GHz User Guide |
Navini Networks, Inc. |
Safety (continued)
11.Do not dispose of the equipment or the battery in a fire. They may explode. Check with the retailer for battery disposal guidelines.
12.Do not open or mutilate the battery. The battery contains substances that are toxic, corrosive, or harmful to humans. If battery substances come in contact with the skin, seek medical help immediately.
13.Do not disassemble the equipment. Removing covers exposes dangerous voltages or other risks and also voids the warranty. Incorrect reassembly can cause equipment damage or electrical shock. Only an authorized repair technician should service this product.
14.Do not expose the equipment to extreme hot or cold temperatures.
15.Do not use the equipment under the following conditions:
When the equipment has been exposed to water or moisture.
When the equipment has been damaged.
When the power cord is damaged or frayed.
When the equipment does not operate properly or shows a distinct change in performance.
CAUTION: RISK OF EXPLOSION IS POSSIBLE IF THE BATTERY IS REPLACED WITH ONE NOT SUPPLIED BY NAVINI NETWORKS. DISPOSE OF USED BATTERIES ACCORDING TO ENVIROMENTAL GUIDELINES.
ix
Ripwave 2.6 GHz User Guide |
Navini Networks, Inc. |
x
Ripwave 2.6 GHz User Guide |
Navini Networks, Inc. |
xi
Ripwave 2.6 GHz User Guide |
Navini Networks, Inc. |
Introduction
Congratulations for being selected to test the Navini Networks Ripwave product. This manual will guide you through the simple process of installing the Navini Networks Ripwave unit and software, which has been developed to optimize the ease and convenience for you, our valued customer.
The Ripwave Unit Installation includes instructions for both USB and Ethernet connections. Be sure to use the instructions that apply to your Ripwave model.
Note: You must have the Ripwave Unit model that is appropriate for your PC port: Model 2600U for a USB connection; Model 2600E for an Ethernet connection. At first glance, the models appear the same, but the ports and cables for the connections are different.
A USB connection will function only with Windows® 98, Windows® 98SE, Windows® 2000, or Windows® ME. It will not work with Windows® 95 or Windows NT®.
An Ethernet connection will function with any Win32 Operating System (Windows® 95 or later).
USB
Model 2600U
Ethernet
Model 2600E
The Software Installation procedure is the same for either of the Ripwave models.
Minimum requirements:
Operating System: |
Windows® 95 or later – Windows XP and |
|
Macintosh systems are not supported. |
CPU: |
Pentium level or higher |
RAM: |
32MB or the Operating System minimum |
|
(whichever is greater) |
Hard Drive: |
10MB free disk space |
Before you start!
Verify the contents of your package. The contents should consist of the following items:
Navini Networks Ripwave unitRipwave unit AC power adapterPC-to-Ripwave unit cable (USB or Ethernet)Ripwave User Guide
Ripwave Quick Installation GuideNavini Networks Ripwave Installation CD
If you do not find all of these items in your package, notify the supplier from whom you obtained your package.
1
Loading...