The MX67/MX68 series devices uses an LED to inform the user of the device's status. LED patterns and their meanings
are described below.
LED StatusMeaning
Solid orange
Alternating Colors
Power is applied but the appliance is not connected to
the Meraki Dashboard
The appliance is attempting to connect to Meraki
Dashboard
2
Flashing WhiteFirmware upgrade in progress
Solid WhiteFully operational
Back Panels
MX67
MX67C
3
MX67W
4
MX67/MX67W/MX67C Back Panel Functions
Additional functions on the back panel are described below, from left to right.
SIM Card Slot (MX67C)
USB port
Active, supported SIM cards can be inserted into this
slot to enable cellular capabilities.
USB 3.0 for external 3G/4G wireless modems. Traffic
status is indicated by the USB LED.
WAN / Internet portThis port provides connectivity to the WAN.
These 4 ports provide connectivity to computers,
LAN ports
printers, access points, or Ethernet switches.
A steady green LED indicates bidirectional connectivity,
and flashing green indicates traffic.
These 2 LAN ports provide connectivity to computers,
PoE+ Ports
printers, access points, or Ethernet switches.
Each port outputs up to 30W of PoE power.
5
A steady green LED indicates bidirectional connectivity,
and flashing green indicates traffic.
Power inputDesigned for use only with the unit’s power supply.
Insert a paper clip if a reset is required.
Reset button
MX68
MX68W
Press for 1 second to delete a downloaded configuration
and reboot.
Press and hold for more than 10 seconds to force a full
factory reset.
6
MX68CW
MX68/MX68W/MX68CW Back Panel Functions
Additional functions on the back panel are described below, from left to right.
WAN / Internet portsThese two ports provide connectivity to the WAN.
These 8 ports provide connectivity to computers,
LAN ports
PoE+ Ports
printers, access points, or Ethernet switches.
A steady green LED indicates bidirectional connectivity,
and flashing green indicates traffic.
These 2 LAN ports provide connectivity to computers,
printers, access points, or Ethernet switches.
7
Each port outputs up to 30W of PoE power.
A steady green LED indicates bidirectional connectivity,
and flashing green indicates traffic.
Power inputDesigned for use only with the unit’s power supply.
Insert a paper clip if a reset is required.
Reset button
Side Panels
MX68
Press for 1 second to delete a downloaded configuration
and reboot.
Press and hold for more than 10 seconds to force a full
factory reset.
MX68W
8
MX68CW
9
MX68/MX68W/MX68CW Side Panel Functions
Additional functions on the side panel are described below, from left to right.
SIM Card Slot (MX68CW)
USB port
Bottom Panel
Active, supported SIM cards can be inserted into this
slot to enable cellular capabilities.
USB 2.0 for 3G/4G wireless cards. Traffic status is
indicated by the USB LED.
Please note that the serial number is located on the product label at the bottom panel of MX67/MX68 devices
10
Mounting Hardware
The supplied wall screws and anchors allow you to mount the appliance on a drywall surface, either vertically or
horizontally. The distance between the holes you drill should be 5-1/8 inches (13 cm).
• For mounting on drywall, use a ¼-in drill bit, then insert the plastic and screw assemblies.
• For mounting on wood or a similar surface, use only the screws.
• Allow the heads of the screws to stick out far enough to be inserted securely into the back of the appliance.
Connecting to WAN
All Meraki MX devices must have an IP address. This section describes how to configure your local area network before
you deploy it. A local management web service, running on the appliance, is accessed through a browser running on a
client PC. This web service is used for configuring and monitoring basic ISP/WAN connectivity.
Setting up a Static IP Address
To ensure that the client PC is redirected to the local web service in the following step, you must disable all
other network services (ex: wi-fi) on your client machine.
Do the following to configure basic connectivity and other networking parameters:
1. Using a client machine such as a laptop, connect to one of the LAN ports of the MX.
2. Using a browser on the client machine, access the appliance's built-in web service by browsing to
http://setup.meraki.com. (You do not have to be connected to the Internet to reach this address)
3. Click Uplink configuration under the Local status tab. The default credentials use the device serial number as
the username, with a blank password field.
4. Choose Static for the IP Assignment option.
5. Enter the IP address, subnet mask, default gateway IP and DNS server information.
Setting up a DHCP IP Address
By default all MX devices are configured to DHCP from upstream WAN / ISP servers. Simply plug the MX's WAN /
Internet port to your upstream circuit and wait a few minutes for the unit to negotiate a DHCP address.
When the WAN connection is fully enabled, Internet LED 1 will turn green.
11
Setting up Cellular Failover
The MX67C and MX68CW have an embedded LTE module for cellular failover connections. The following section will
walk through first-time set-up of an MX with an internet connection as a primary connection and cellular as failover.
Note that the IMEI cannot yet be found on the Meraki dashboard, only on the physical label of the device. The
IMEI of the MXs with embedded LTE, as well as the serial number and MAC address, can be found on the
product label at the bottom of cellular-embedded MX devices.
To set up the cellular failover connection, follow the steps below:
1. For the MX67C, connect the antennas for cellular reception. Antennae are pre-attached for the MX68CW
2. Connect the uplink for the MX device via a wired connection to connect to the Meraki cloud
3. Open the SIM tray using the SIM card removal tool included in the box
4. Insert a nano SIM card (4FF size) and close the SIM tray
5. Check with the carrier of choice if an APN needs to be configured. If so, do that from the Meraki Dashboard under
Security Appliance > Monitor > Appliance Status > Uplink tab
6. The Meraki dashboard will automatically recognize the new cellular connection and you will be able to see the
status on the left hand side of the Appliance Status page and in the Uplink tab
7. Test the cellular failover connection by unplugging the wired connection or by using the traceroute tool under
Security Appliance > Monitor > Appliance Status in the Tools tab
8. If, after following the steps above, the SIM card is not detected, please confirm with your carrier that the SIM card
is active and has data. You will need the ICCID of the SIM card and IMEI of the device to get troubleshooting help
from the carrier
◦ A list of certified carriers can be found here
9. Please contact the Meraki Support team if the cellular connection is still not being recognized after following the
steps above
12
Additional Settings
Please note that all these settings below are accessible only via the local management console.
Setting VLANs
If your WAN uplink is on a trunk port, choose VLAN tagging > Use VLAN tagging and enter the appropriate value for
VLAN ID for your network.
Setting up a Secondary WAN Interface on the MX68
MX68 devices come with two dedicated Internet ports, which are both configured on the Security Appliance >
Appliance Status > Local Status under the Uplink Configuration.
Setting up a Secondary WAN interface on the MX67
You can toggle the LAN2 port between LAN and Internet, through Local Status Page
Setting PPPoE
PPPoE authentication may be required if you are connecting MX device to a DSL circuit. You need to know your
authentication option and credentials (supplied by your ISP) in order to complete these steps.
• Choose Connection Type > PPPoE.
• Select your Authentication option.
• If you select Use authentication, enter appropriate values for Username and Password.
Web Proxy Settings
These settings take effect if the MX device has to fall back to using HTTP to contact the Cloud Controller. By default,
web proxy is disabled. To enable web proxy, do the following:
• Choose Web proxy > Yes.
• Enter values as appropriate for Hostname or IP and Port.
• If you require authentication, choose Authentication > Use authentication, and enter appropriate values for
Username and Password.
To apply all configuration settings to the appliance, be sure to click Save Settings at the bottom of the page.
Configuring Physical Link Settings
To configure physical link settings on the Ethernet ports, click Local status > Ethernet configuration. You can enable
half duplex, full duplex, and autonegotiation, as well as set 10- or 100-Mbps data rates.
13
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.