Cisco Linksys RV0041 Quick Install Manual

Model No.

Quick Installation

Quick Installation

A Division of Cisco Systems, Inc.

®

Model No.

WIRED

RV0041

VPN Router

10/100/1000 4-Port

Package Contents

• 10/100/1000 4-Port VPN Router

•User Guide CD-ROM

• AC Power Cable

• Rack Mounting Kit

• Quick Installation

• Registration Card

1

A Before you begin, make sure

that all of your hardware is
powered off, including the
Router, PCs, hubs, switches,
and cable or DSL modem.

B Connect one end of an Ether-

net network cable to one of
the numbered ports on the
front of the Router. Connect
the other end to an Ethernet
port on a network device, e.g.,
a PC, print server, hub, or
switch.

Repeat this step to connect
more PCs or other network
devices to the Router.

C Connect your cable or DSL

modem’s Ethernet cable to
the Router’s Internet port.

D Power on the cable or DSL

modem and the other network
device if using one.

2

Connect the Router

In Step 2, you will need the setup
instructions provided by your Inter­net Service Provider (ISP). If you do
not have this information, then con­tact your ISP before proceeding.

The instructions from your ISP tell you
how to set up your PC for Internet
access. Because you are now using
the Router to share Internet access
among several computers, you will
use the setup information to config­ure the Router instead of your PC.

A Open your PC’s web browser.

Enter http://192.168.1.1 (the
Router’s default local IP
address) in the web browser’s
Address field. Then press the
Enter key.

B A screen will appea r and ask

you for a User Name and Pass­word. Enter admin (the default)
in the the User Name and Pass-
word fields. Then click the OK
button.

E

B

Configure the Router

A

E Connect the included AC

power cable to the Router’s
Power port on the back of the
Router, as shown in Figure E,
and then plug the other end of
the power cable into an elec­trical outlet.

The System LED on the front
panel will light up as soon as
the power adapter is con­nected properly.

NOTE:: Make sure your PC’s Ethernet
adapter is set to obtain an IP address
automatically. For more information,
refer to Windows Help.

Obtain an IP

1 Obtain an IP Automatically

a If your ISP says that you are

connecting through DHCP or a
dynamic IP address from your
ISP, then select Obtain an IP
automatically as the WAN
Connection Type. If you also
select Use the Following DNS
Server Addresses, enter a spe­cific DNS Server IP Address.

b Click the Save Settings button,

and go to Step G.

2 Static IP

a If your ISP says that you are

connecting through a static or
fixed IP address from your ISP,
then select Static IP as the WAN
Connection Type.

b Enter the WAN IP Address, Sub-

net Mask Default Gateway
Address, and DNS Server pro­vided by your ISP.

c In the DNS Server fields, enter

the DNS address(es) provided
by your ISP. You need to enter
at least one DNS address.

d Click the Save Settings button,

and go to Step G.

C The Router’s Web-based Utility

will appear with the System
Summary screen showing.
Click on the Setup tab, which is
the next tab over, then con­tinue with the instruction,
below, to complete the Net-
work page.

D Depending on the setup infor-

mation from your ISP, you may
need to provide a host name
and domain name for the
Router. The Host Name and
Domain Name fields are usu­ally left blank. If requested by
your ISP (usually cable ISPs),
complete these two fields.

E Choose the internet inter face

you wish to use, the RJ45 or the
SFP. Only one of these ports
can be used at the same time.

F In the drop-down menu for the

WAN Connection Type setting
features four Internet connec­tion types: obtain an IP auto­matically, Static IP, PPPoE, and
PPTP. Depending on which con­nection type you select, the
features available on the Net-
work page of the Setup screen
will differ. Proceed to the
instructions for the connection
type you are using.

G If you haven’t already done so,

click the Save Settings button.
Then, close the web browser.

H Power your cable or DSL

modem off and back on
again.

I Restart or power on your PCs so

they can obtain the Router’s
new settings.

J To test the Router’s settings,

open your web browser from
any computer. In the browser’s
Address field, enter
www.linksys.com/registration
and press the Enter key.

Congratulations! The installation of

the Router is complete.

3PPPoE

a If your ISP says that you are

connecting through PPPoE or if
you normally enter a user
name and password to access
the Internet, then select PPPoE
as the WAN Connection Type.

b Enter the User Name and Pass-

word provided by your ISP.

c If you select Connect on

Demand, the PPPoE connec­tion will be disconnected if it
has been idle for a period
longer than the Max Idle Time
setting.

d If you select Keep Alive, the

Router will keep the connec­tion alive by sending out a few
data packets at the Redial
Period, so your Internet service
thinks that the connection is still
active.

e Click the Save Settings button.

f Go to Step G.

4PPTP

PPTP is a service used in Europe and
Israel only. IF you are using a PPTP
connection, check with your ISP for
the necessary setup information.
When you are finished, go to Step G.

RV0041-QI-50505 KL

For additional information or troubleshooting
help, refer to the User Guide on the Setup CD­ROM. You can also call or e-mail for further
support.

24-hour Technical Support

800-326-7114
(toll-free from US or Canada)

E-mail Support

[e-mail]

Website

http://www.linksys.com or

http://support.linksys.com

RMA (Return Merchandise Authorization)

http://www.linksys.com/support

FTP Site

ftp://ftp.linksys.com

Sales Information

800-546-5797 (800-LINKSYS)

Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries. Copyright © 2005
Cisco Systems, Inc. All rights reserved.

Model No.

Static IP

PPPoE

PPTP

J

D

C

automatically