Cisco IE-5000-16S12P, IE-5000-12S12P-10G User Manual

Product Overview

The Cisco IE 5000 hardened aggregator provides a rugged and secure switching infrastructure for harsh environments. It is suitable for
industrial Ethernet applications, including process manufacturing, intelligent transportation systems (ITSs), rail transportation, and other
similar deployments.

In industrial environments, you can connect the switch to any Ethernet-enabled industrial communication devices, including programmable
logic controllers (PLCs), human-machine interfaces (HMIs), drives, sensors, and input and output (IO) devices.

For detailed specifications, see the IE 5000 Data Sheet.

 Switch Models, page 1

 Cable Side, page 2

 Power-Supply Side, page 10

 Management Options, page 12

Switch Models

Table 1 Switch Models

Model Total

Ports

IE-5000-16S12P 28 4 GE only 12 12 LAN Base Support for 2 field-replaceable, redundant

IE-5000-12S12P-10G 28 4GE/10GE 12 12 LAN Base Support for 2 field-replaceable, redundant

1. PoE+ = Power over Ethernet.

2. Can be upgraded to IP Services at a fee. IP Services License Product Numbers are the following: L-IE5000-RTU= (Electron ic SW License for IE5000
Switches)

SFP/SFP+
Uplinks

FE/GE SFP
Downlinks

Copper
10/100/1000
PoE/PoE+
Ports

Default
Software

1

License

Power Supplies

2

AC or DC power supplies.

For detailed specifications, see the

IE 5000 Data Sheet.

AC or DC power supplies.

For detailed specifications, see the

IE 5000 Data Sheet.

Cisco Systems, Inc. www.cisco.com

1

Product Overview

Cable Side

Cable Side

Figure 1 Cisco IE-5000 Cable-Side View

1 4 5

2 6 73

12 11 10 813

1 LEDs 8 Power-input terminal
2 Display mode button 9 Alarm port
3 GPS antenna port 10 Console port
4 Digital Timecode I/O (IRIG)

(Not currently supported by software)

5 Analog Timecode I/O (IRIG)

(Not currently supported by software)

6 USB (mini-Type B) console port 12 (bottom) Twelve 100/1000 SFP Ports (Downlinks)
7 Time of Day (TOD) Port

(Not currently supported by software)

LEDs

For detailed information about LEDs see LEDs, page 6.

Display Mode Button

For detailed functionality see Display Mode Button, page 8.

9

11 Four 1000 SFP/10G SFP+ Ports (Uplinks)

12(top) Twelve 10/100/1000 PoE/PoE+ Ports (Downlinks)

13 Flash memory card slot

349768

GPS Antenna Port

GNSS Module RF Input Requirements

The GPS/GNSS input requires a GPS/GNSS receive antenna with built-in Low-Noise Amplifier (LNA) for optimal performance. The LNA
amplifies the received satellite signals to:

 Compensate for cable loss

 Increase the signal amplitude to a suitable range for the receiver front-end

2

Product Overview

Cable Side

The amplification required is 22dB gain + cable loss + connector loss.

The recommended range of LNA gain (LNA gain minus all cable and connector losses) at the connector of the receiver input is 22dB to
30dB with a minimum of 20dB and a maximum of 35dB.

 The GPS/GNSS input on the IE 5000 provides 3.3 or 5VDC (software configurable) to the antenna through the same RF connector.

The antenna should draw between 10 and 100mA. An antenna that draws less than 10mA may wrongly report and "Antenna Open"
fault even though the antenna is operating properly.

Power Requirements

When deployed in a hazardous environment the antenna shall only use power provided by the RF input from a single IE 5000. No additional
power may be supplied to the antenna and associated equipment.

Caution: Supplying additional power, such as with a powered splitter or amplified repeater, may provide enough energy to create

an arc that could ignite the explosive atmosphere.

Surge requirement:

The GPS/GNSS input has built-in ESD protection. If an outdoor antenna is being connected, additional surge protection will be required to
meet the regulations and standards for lightning protection in the countries where the end-product is installed.

The lightning protection must be mounted at the place where the antenna cable enters the building. The primary lightning protection must
be certified for conducting all potentially dangerous electrical energy to PE (Protective Earth). Surge arrestors should support DC-pass and
be suitable for the GPS/GNSS frequency range with low RF attenuation.

Caution: The antenna terminal should be earthed at the building entrance in accordance with the ANSI/NFPA 70, the National Electrical

Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable.

Antenna Sky visibility:

GPS signals require a direct line of sight between antenna and satellite. The antenna should see as much of the sky as possible. Fixed
installations require four satellites in view for an initial time fix, while subsequent updates may be possible with fewer satellites.

Console Ports

You can connect the switch to a PC running Microsoft Windows or to a terminal server through either the RJ-45 console port or the USB
console port.

 RJ-45 console port. The RJ-45 connection uses an RJ-45-to-DB-9 female cable.

 USB mini-Type B console port (5-pin connector). The USB connection uses a USB Type A-to-5-pin mini-Type B cable.

The USB console interface speeds are the same as the RJ-45 console inte rface speeds.

To use the USB console port, you must install the Cisco Windows USB device driver on the device that is connected to the USB console
port (device running with Microsoft Windows). See Installing the Cisco Microsoft Windows XP, 2000, Vista, 7, 8, and 10 USB Device

Driver, page 64 for more information.

With the Cisco Windows USB device driver, connecting and disconnecting the USB cable from the console port does not affect Windows
HyperTerminal oper ations. Mac OS X or Linux require no special drivers.

Note: The 5-pin mini-Type B connectors resemble the 4-pin mini-Type B connectors. They are not compatible. Use only the 5-pin

mini-Type B.

3

Product Overview

253163

Cable Side

Figure 2 USB Mini-Type B Port

The configurable inactivity timeout reactivates the RJ-45 console port if the USB console port is activated, but no input activity occurs on
it for a specified time period. When the USB console port deactivates due to a timeout, you can restore its operation by disconnecting and
reconnecting the USB cable. For information on using the CLI to configure the USB console interface, see the switch software guide.

Power-Input Terminal

The power-input terminal provides screw terminals for the AC and DC power connections. The switch can operate with one or two power
supplies. If one of the power sources fail, the other continues to power the switch. See Power Supply Installation, page 33 for information.

Figure 3 Power-Input Terminal

208415

Alarm Ports

The switch has four alarm inputs and one alarm output.

Alarm Input

The alarm input is a dry-contact alarm port. You can connect up to four alarm inputs from devices, such as a door, a temperature gauge, or
a fire alarm, to the alarm port. You can use the CLI to set the alarm severity to minor, or major. An alarm generates a system message and
turns on an LED. See the Alarm LEDs, page 9 for the LED descriptions.

Alarm Output

The alarm output can be configured as a major alarm. Output alarms often control a n external alarm, such as a be ll or a light. To connect an
external alarm device to the relay, you connect two relay contact wires to complete the electrical circuit. See for information on the alarm
pinouts. see the Alarm Port, page 54.

Four 1000 SFP/10G SFP+ Ports (Uplinks)

Depending on the switch model, the uplink ports support either GE optics and 10G optics, or only GE optics. Wh en using a 1000BaseT SFP,
the port only operates at 1000 mbps.

For more information about SFP/SFP+ modules and cables, see Transceiver Modules. See Switch Models, page 1 for model information.

4