Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-25818-04
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not
installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to
comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital
devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television
communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its
peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
• Turn the television or radio antenna until the interference stops.
• Move the equipment to one side or the other of the television or radio.
• Move the equipment farther away from the television or radio.
• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits
controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the
document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
Obtaining Documentation, Obtaining Support, and Security Guidelinesviii
CHAPTER
1Product Overview1-1
Switch Models1-2
Front Panel1-5
10/100BASE-T Downlink Ports1-8
Power over Ethernet Ports1-9
10/100BASE-T Uplink Ports1-9
10/100/1000BASE-T Uplink Ports1-9
100 Mb/s SFP Module Uplink Slots1-9
100/1000 Mb/s SFP Module Uplink Slots1-9
Dual-Purpose Fast Ethernet Uplink Ports1-9
Dual-Purpose Gigabit Ethernet Uplink Ports1-10
Power Connectors1-11
PoE Power Connector1-12
Alarm Connector1-12
Management Ports1-13
LEDs1-14
Express Setup LED1-15
System LED1-15
USB-Mini Console LED1-15
Alarm LEDs1-16
Power Status LEDs1-16
Port Status LEDs1-17
Dual-Purpose Port LEDs1-18
PoE Status LED1-19
Flash Memory Card1-19
OL-25818-04
Rear Panel1-21
Cisco IE 2000 Switch Hardware Installation Guide
iii
Contents
Management Options1-21
Network Configurations1-22
CHAPTER
2Switch Installation2-1
Preparing for Installation2-1
Warnings2-1
Additional Information for Installation in a Hazardous Environment2-3
Hazardous Area Installation Warnings2-3
North American Hazardous Location Approval2-5
EMC Environmental Conditions for Products Installed in the European Union2-5
Installation Guidelines2-5
Environment and Enclosure Guidelines2-5
General Guidelines2-6
Verifying Package Contents2-7
Installing or Removing the Flash Memory Card (Optional)2-7
Connecting to a Console Port2-9
RJ-45 Console Port2-10
USB Mini-Type B Console Port2-11
Connecting to Power2-13
Tools and Equipment2-13
Supported Power Supplies2-13
Installing the Power Converter on a DIN Rail, Wall, or Rack Adapter2-14
Grounding the Switch2-14
Connecting the Power Converter to an AC Power Source2-17
Preparing the AC Power Connection2-17
Connecting the AC Power Source to the Power Converter2-18
Connecting the Power Converter to a DC Power Source2-19
Wiring the DC Power Source2-20
Attaching the Power Connectors to the Switch2-25
Connecting Power to the Switch PoE DC-Input (Optional)2-28
Applying Power to the Power Converter2-30
Running Boot Fast2-30
Powering On the Switch2-30
Verifying Boot Fast2-31
Disconnecting Power2-31
iv
Installing the Switch2-31
Installing the Switch on a DIN Rail2-32
Removing the Switch from a DIN Rail 2-33
Connecting Alarm Circuits2-34
Cisco IE 2000 Switch Hardware Installation Guide
OL-25818-04
Wiring the Protective Ground and DC Power for Alarm Circuits2-34
Wiring the External Alarms2-35
Attaching the Alarm Connector to the Switch2-38
Connecting Destination Ports2-39
Connecting to 10/100 and 10/100/1000 Ports2-40
Installing and Removing SFP Modules2-42
Installing SFP Modules into SFP Module Slots2-42
Removing SFP Modules from SFP Module Slots2-43
Connecting to SFP Modules2-44
Connecting to a Dual-Purpose Port2-46
SFP Module CablesB-4
Cable PinoutsB-7
Console Port Adapter PinoutsB-8
CConfiguring the Switch with the CLI-Based Setup ProgramC-1
Accessing the CLI Through the Console PortC-1
Removing the USB Mini-Type B Console Port CoverC-1
RJ-45 Console PortC-2
USB Mini-Type B Console PortC-4
Installing the Cisco Microsoft Windows USB Device DriverC-5
Installing the Cisco Microsoft Windows XP USB DriverC-5
Installing the Cisco Microsoft Windows 2000 USB DriverC-6
Installing the Cisco Microsoft Windows Vista and Windows 7 USB DriverC-6
Uninstalling the Cisco Microsoft Windows USB DriverC-7
Uninstalling the Cisco Microsoft Windows XP and 2000 USB DriverC-7
Uninstalling the Cisco Microsoft Windows Vista and Windows 7 USB DriverC-7
vi
Entering the Initial Configuration InformationC-8
IP SettingsC-8
Completing the Setup ProgramC-8
Cisco IE 2000 Switch Hardware Installation Guide
OL-25818-04
Audience
Preface
This guide is for the networking or computer technician responsible for installing Cisco IE 2000 series
switches. We assume that you are familiar with the concepts and terminology of Ethernet and local area
networking.
Purpose
This guide documents the hardware features of the Cisco IE 2000 switches. It describes the physical and
performance characteristics of each switch, explains how to install a switch, and provides
troubleshooting information.
This guide does not describe system messages that you might receive or how to configure your switch.
For more information, see the Cisco IE2000 documentation at
This document uses the following conventions and symbols for notes, cautions, and warnings.
NoteMeans reader take note. Notes contain helpful suggestions or references to materials not contained in
this manual.
OL-25818-04
CautionMeans reader be careful. In this situation, you might do something that could result in equipment
damage or loss of data.
Cisco IE 2000 Switch Hardware Installation Guide
vii
Chapter
Warning
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this device.
Statement 1071
The safety warnings for this product are translated into several languages in the Regulatory Compliance
and Safety Information for the Cisco IE 2000 Switch that ships with the product. The EMC regulatory
statements are also included in that guide.
Related Publications
Before installing, configuring, or upgrading the switch, see the release notes on Cisco.com for the latest
information.
These documents provide complete information about the switch and are available on Cisco.com:
• Cisco IE 2000 Switch Getting Started Guide
• Regulatory Compliance and Safety Information for the Cisco IE 2000 Switch
• Cisco Gigabit Ethernet Transceiver Modules Compatibility Matrix (not orderable but available on
Cisco.com)
• Cisco Small Form-Factor Pluggable Modules Compatibility Matrix (not orderable but available on
Cisco.com)
Obtaining Documentation, Obtaining Support, and Security
Guidelines
For information on obtaining documentation, obtaining support, providing documentation feedback,
security guidelines, and also recommended aliases and general Cisco documents, see the monthly
What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical
documentation, at:
This switch provides a rugged and secure switching infrastructure for harsh environments. It is suitable
for industrial Ethernet applications, including factory automation, intelligent transportation systems
(ITSs), substations, oil and gas installations, and other deployments in harsh environments.
You can connect this switch to office networking devices such as Cisco IP phones, Cisco Wireless Access
Points workstations, and other devices such as servers, routers, and other switches. In industrial
environments, you can connect any Ethernet-enabled industrial communication devices, including
programmable logic controllers (PLCs), human-machine interfaces (HMIs), drives, sensors, video
devices, traffic signal controllers, and intelligent electronic devices (IEDs).
You can mount the switch on a DIN rail in an industrial enclosure. Its components are designed to
withstand extremes in temperature, vibration, and shock that are common in an industrial environment.
3USB mini-Type B (console) port8Protective ground connection
4RJ-45 console port9Flash memory card slot
5Power connector DC-A10 PoE power connector
10/100BASE-T Downlink Ports
4
±12/24/48
0.5-3.0A
5
6
A
7
8
2
9
347587
1-8
You can set the 10/100BASE-T downlink ports to operate at 10 or 100 Mb/s in full-duplex or half-duplex
mode. You can also set these ports for speed and duplex autonegotiation in compliance with
IEEE 802.3AB. (The default setting is autonegotiate.) When set for autonegotiation, the port senses the
speed and duplex settings of the attached device and advertises its own capabilities. If the connected
device also supports autonegotiation, the switch port negotiates the best connection (that is, the fastest
line speed that both devices support, and full-duplex transmission if the attached device supports it) and
configures itself accordingly. In all cases, the attached device must be within 328 feet (100 meters).
100BASE-TX traffic requires Category 5 cable. 10BASE-T traffic can use Category 3 or Category 4
cables.
When connecting the switch to workstations, servers, routers, and Cisco IP phones, make sure that the
cable is a straight-through cable.
Cisco IE 2000 Switch Hardware Installation Guide
OL-25818-04
Chapter 1 Product Overview
You can use the mdix auto interface configuration command in the command-line interface (CLI) to
enable the automatic medium-dependent interface crossover (auto-MDIX) feature. When the autoMDIX feature is enabled, the switch detects the required cable type for copper Ethernet connections and
configures the interfaces accordingly. For configuration information for this feature, see the switch
software configuration guide or the switch command reference.
Power over Ethernet Ports
On certain models of the IE 2000 switch, four of the 10/100BASE-T ports are available as PoE ports.
The four ports can operate as PoE (IEEE 802.3af) ports or can be configured to operate as PoE+
(IE 802.at) ports. Each PoE port requires 15.4 Watts of power while PoE+ requires 30 Watts. A 54VDC
/1.2Amp power source (65W) can support 4 PoE ports or 2 PoE+ ports.
Cable lengths of up to 328 ft (100 m) are supported.
10/100BASE-T Uplink Ports
The IEEE 802.3u 10/100BASE-T uplink ports provide full-duplex 10, 100 Mb/s connectivity over
Category 5 unshielded twisted pair (UTP) copper cabling. The default setting is autonegotiate. The cable
can be up to 100 m (0.1 km) in length.
Front Panel
10/100/1000BASE-T Uplink Ports
The IEEE 802.3u 10/100/1000BASE-T uplink ports provide full-duplex 10, 100 or 1000 Mb/s
connectivity over Category 5 unshielded twisted pair (UTP) copper cabling. The default setting is
autonegotiate. The cable can be up to 100 m (0.1 km) in length.
100 Mb/s SFP Module Uplink Slots
The IEEE 802.3u 100 Mb/s SFP module uplink slots provide full-duplex 100 Mb/s connectivity over
multi-mode (MM) fiber cables or single-mode (SM) fiber cables. These ports use a SFP fiber-optic
transceiver module that accepts a dual LC connector. Check the SFP specifications for the cable type and
length.
100/1000 Mb/s SFP Module Uplink Slots
The IEEE 802.3u 100 Mb/s SFP module uplink slots provide full-duplex 100 or 1000 Mb/s connectivity
over multi-mode (MM) fiber cables or single-mode (SM) fiber cables. These ports use a SFP fiber-optic
transceiver module that accepts a dual LC connector. Check the SFP specifications for the cable type and
length.
Dual-Purpose Fast Ethernet Uplink Ports
OL-25818-04
You can configure the dual-purpose Fast Ethernet uplink ports on the switch as either 10/100BASE-T
ports or as 100 Mb/s SFP-module ports. You can set the 10/100 ports to autonegotiate, or you can
configure them as fixed 10 or 100 Mb/s ports.
Cisco IE 2000 Switch Hardware Installation Guide
1-9
Front Panel
By default, the switch selects the medium for each dual-purpose port (10/100BASE-T or SFP). When a
link is achieved on one media type, the switch disables the other media type until the active link goes
down. If links are active on both media, the SFP-module port has priority, but you can use the media-type interface configuration command to manually designate the port as an RJ-45 port or an SFP port.
You can configure the speed and duplex settings consistent with the selected media type. For information
on configuring interfaces, see the switch software configuration guide.
Dual-Purpose Gigabit Ethernet Uplink Ports
You can configure the dual-purpose Gigabit Ethernet uplink ports on the switch as either
10/1001000BASE-T ports or as 100/1000 Mb/s SFP-module ports. You can set the 10/100/1000BASET ports to autonegotiate, or you can configure them as fixed 10, 100, or 1000 Mb/s (Gigabit) Ethernet
ports.
By default, the switch selects the medium for each dual-purpose port (10/100/1000BASE-T or SFP).
When a link is achieved on one media type, the switch disables the other media type until the active link
goes down. If links are active on both media, the SFP-module port has priority, but you can use the
media-type interface configuration command to manually designate the port as an RJ-45 port or an SFP
port.
You can configure the speed and duplex settings consistent with the selected media type. For information
on configuring interfaces, see the switch software configuration guide.
Chapter 1 Product Overview
SFP Modules
NoteThe Cisco IE 2000 switch does not support copper SFP modules.
The SFP modules are switch Ethernet SFP modules that provide connections to other devices. These
field-replaceable transceiver modules provide the uplink interfaces. The modules have LC connectors
for fiber-optic connections.
You can use any combination of the supported SFP modules:
Table 1-2Supported SFP Models
Type of SFP ModuleModel
Rugged and Industrial SFPs
–40 to 185°F (–40 to 85°C)
• GLC-SX-MM-RGD with digital optical monitoring (DOM)
support
• GLC-LX-SM-RGD with DOM support
• GLC-ZX-SM-RGD with DOM support
1-10
Cisco IE 2000 Switch Hardware Installation Guide
OL-25818-04
Chapter 1 Product Overview
Table 1-2Supported SFP Models
Type of SFP ModuleModel
Commercial SFPs
Front Panel
• GLC-SX-MM
32 to 158°F (0 to 70°C)
Extended temperature SFPs
23 to 185°F (–5 to 85°C)
• GLC-LH-SM
• GLC-BX-U with DOM support
• GLC-BX-D with DOM support
• CWDM-SFP with DOM support
• DWDM-SFP with DOM support
• SFP-GE-S with DOM support
• SFP-GE-L with DOM support
• SFP-GE-Z with DOM support
• GLC-SX-SMD
• GLC-LH-SMD
• GLC-EX-SMD
For the most up-to-date list of supported SFP models for Cisco Industrial Ethernet switches, see
For installation instructions, see your SFP module documentation and the “Installing and Removing SFP
Modules” section on page 2-42.
For cable specifications, see the “SFP Module Cables” section on page B-4.
Power Connectors
You connect the DC power to the switch through the front panel connectors. The switch has a dual-feed
DC power supply; two connectors provide primary and secondary DC power (DC-A and DC-B). The DC
power connectors are near the top right of the front panel. See Figure 1-1. Each power connector has an
LED status indicator.
The switch power connectors are attached to the switch chassis. Each power connector has screw
terminals for terminating the DC power (see Figure 1-5). All connectors are attached to the switch front
panel with the provided captive screws.
The power connector labeling is on the panel. The positive DC power connection is labeled “+”, and the
return connection is labeled “–”.
OL-25818-04
Cisco IE 2000 Switch Hardware Installation Guide
1-11
Front Panel
331209
Figure 1-5Power Connector
The switch can operate with a single power source or with dual power sources. When both power sources
are operational, the switch draws power from the DC source with the higher voltage. If one of the two
power sources fail, the other continues to power the switch.
PoE Power Connector
The IE 2000 switch models with PoE capability (IE-2000-16PTC-G-E, IE-2000-16PTC-G-L, and IE2000-16PTC-G-NX) are equipped with an additional DC input terminal block. This DC terminal block
allows the connection of a second power supply (see the “Power over Ethernet Ports” section on page 1-
9), or a second input from site source DC power to operate the PoE ports. The PoE terminal block accepts
48 VDC or 54 VDC at 2.5 A.
Chapter 1 Product Overview
Alarm Connector
You connect the alarm signals to the switch through the alarm connector. The switch supports two alarm
inputs and one alarm output relay. The alarm connector is on the bottom right of the front panel. See
Figure 1-2.
The alarm connector provides six alarm wire connections. The connector is attached to the switch front
panel with the provided captive screws.
Figure 1-6Alarm Connector
Both alarm input circuits can sense if the alarm input is open or closed. The alarm inputs can be activated
for environmental, power supply, and port status alarm conditions. From the CLI, you can configure each
alarm input as an open or closed contact.
The alarm output circuit is a relay with a normally open and a normally closed contact. The switch is
configured to detect faults that are used to energize the relay coil and change the state on both of the
relay contacts: normally open contacts close, and normally closed contacts open. The alarm output relay
can be used to control an external alarm device, such as a bell or a light.
331208
1-12
See the switch software configuration guide for instructions on configuring the alarm relays.
For more information about the alarm connector, see Appendix B, “Cable and Connectors.”
Cisco IE 2000 Switch Hardware Installation Guide
OL-25818-04
Chapter 1 Product Overview
Management Ports
You can connect the switch to a PC running Microsoft Windows or to a terminal server through either
the RJ-45 console port or the USB mini-Type B console port, also referred to as the USB-mini console
port. These ports use the following connectors:
• RJ-45 console port uses an RJ-45-to-DB-9 female cable.
• USB-mini console port (5-pin connector) uses a USB Type A-to-5-pin mini-Type B cable.
The USB-mini console interface speeds are the same as the RJ-45 console interface speeds.
To use the USB-mini console port, you must install the Cisco Windows USB device driver on the device
that is connected to the USB-mini console port and that is running Microsoft Windows.
NoteFor information about downloading the Cisco USB device driver, see the “Installing the Cisco Microsoft
Windows USB Device Driver” section on page C-5.
With the Cisco Windows USB device driver, connecting and disconnecting the USB cable from the
console port does not affect Windows HyperTerminal operations. Mac OS X or Linux require no special
drivers.
Front Panel
NoteThe 5-pin mini-Type B connectors resemble the 4-pin mini-Type B connectors, but they are not
compatible. Use only the 5-pin mini-Type B. See Figure 1-7.
Figure 1-7USB Mini-Type B Port
253163
The configurable inactivity timeout reactivates the RJ-45 console port if the USB-mini console port is
activated, but no input activity occurs for a specified time period. When the USB-mini console port
deactivates due to a timeout, you can restore its operation by disconnecting and reconnecting the USB
cable. For information on using the CLI to configure the USB-mini console interface, see the switch
software guide.
OL-25818-04
Cisco IE 2000 Switch Hardware Installation Guide
1-13
Front Panel
±12/24/48
0.5-3.0A
LEDs
Chapter 1 Product Overview
You can use the LEDs to monitor the switch status, activity, and performance. Figure 1-8 and Figure 1-
9 show the front panel LEDs.
Figure 1-8LEDs on the Cisco IE 2000 Switch
3
2
7
4
5
±12/24/48
0.5-3.0A
16TC
1
8
6
9
331565
1Alarm LEDs6Power connector DC-B LED
2USB mini-Type B (console) port LED 710/100BASE-T downlink port LEDs
3Express Setup LED8SFP module slot LEDs
4System LED9Dual-purpose uplink port LEDs
5Power connector DC-A LED
NoteOn IE 2000 switches with PoE support, the two SFP ports and the associated LEDs are replaced by a
PoE DC-input terminal block and a PoE LED. See Table 1-10 for the PoE LED colors and meanings.
1-14
Cisco IE 2000 Switch Hardware Installation Guide
OL-25818-04
Chapter 1 Product Overview
Express Setup LED
System LED
Front Panel
The Express Setup LED displays the express setup mode for the initial configuration. Table 1-3 lists the
LED colors and their meanings.
Ta b l e 1-3S etu p LED
ColorSetup Status
Off (dark)Switch is configured as a managed switch.
Solid greenSwitch is operating normally.
Blinking greenSwitch is in initial setup, in recovery, or initial setup is
incomplete.
Solid redSwitch failed to start initial setup or recovery because
there is no available switch port to which to connect the
management station. Disconnect a device from a switch
port, and then press the Express Setup button.
The System LED shows whether the system is receiving power and is functioning properly.
Table 1-4 lists the system LED colors and their meanings.
Ta b l e 1-4S y s t e m L E D
ColorSystem Status
OffSystem is not powered on.
Blinking greenBoot fast is in progress.
GreenSystem is operating normally.
RedSwitch is not functioning properly.
USB-Mini Console LED
The USB-mini console LED shows which console port is in use. See Figure 1-8 for the LED location.
If you connect a cable to a console port, the switch automatically uses that port for console
communication. If you connect two console cables, the USB-mini console port has priority. Tab le 1 -5
describes the system LED colors and their meanings.
Table 1-5USB-Mini Console Port LED
ColorDescription
GreenUSB-mini console port is active.
OffPort is not active.
RJ-45 console port LED is not active.
RJ-45 console port is active.
OL-25818-04
Cisco IE 2000 Switch Hardware Installation Guide
1-15
Front Panel
Alarm LEDs
Chapter 1 Product Overview
Table 1-6 and Tab le 1 -7 list the alarm LED colors and their meanings.
Table 1-6Alarm OUT Status LED
ColorSystem Status
OffAlarm OUT is not configured, or the switch is off.
GreenAlarm OUT is configured, no alarm detected.
Blinking redSwitch has detected a major alarm.
RedSwitch has detected a minor alarm.
Table 1-7Alarm IN1 and IN2 Status LEDs
ColorSystem Status
OffAlarm IN1 or IN2 not configured.
GreenAlarm IN1 or IN2 configured, no alarm detected.
Blinking redMajor alarm detected.
RedMinor alarm detected.
Power Status LEDs
NoteThe Power A and Power B LEDs show that power is not present on the switch if the power input drops
The switch can operate with one or two DC power sources. Each DC input has an associated LED that
shows the status of the corresponding DC input. If power is present on the circuit, the LED is green. If
power is not present, the LED color depends on the alarm configuration. If alarms are configured, the
LED is red when power is not present; otherwise, the LED is off.
If the switch has dual power sources, the switch draws power from the power source with the higher
voltage. If one of the DC sources fails, the alternate DC source powers the switch, and the corresponding
power status LED is green. The power status for the failed DC source is either off or red, depending on
the alarm configuration.
Table 1-8 lists the power status LED colors and meanings.
Table 1-8Power Status LEDs
ColorSystem Status
GreenPower is present on the associated circuit, system is operating normally.
OffPower is not present on the circuit, or the system is not powered up.
RedPower is not present on the associated circuit, and the power supply alarm is configured.
below the low valid level. The power status LEDs only show that power is present if the voltage at the
switch input exceeds the valid level.
1-16
For information about the power LED colors during the boot fast sequence, see the “Verifying Switch
Operation” section on page 2-47.
Cisco IE 2000 Switch Hardware Installation Guide
OL-25818-04
Chapter 1 Product Overview
Port Status LEDs
Front Panel
Each 10/100BASE-T downlink port, 10/100BASE-T uplink port, 10/100/1000BASE-T uplink port,
dual-purpose uplink port, and SFP Module uplink slot has a port status LED, also called a port LED, as
shown in Figure 1-8 and Figure 1-9. Tab le 1-9 displays LED information about the switch and the
individual ports.
Ta b l e 1-9P o r t S t a t u s L E D s
ColorSystem Status
OffNo link.
Solid greenLink present.
Blinking green Activity. Port is sending or receiving data.
Alternating
green-amber
Solid amberPort is not forwarding. The port was disabled by management,
Link fault. Error frames can affect connectivity, and errors
such as excessive collisions, CRC errors, and alignment and
jabber errors are monitored for a link-fault indication.
an address violation, or STP.
NoteAfter a port is reconfigured, the port LED can remain
amber for up to 30 seconds while STP checks the
switch for possible loops.
OL-25818-04
Cisco IE 2000 Switch Hardware Installation Guide
1-17
Front Panel
16TC
±12/24/48
0.5-3.0A
332704
1
Dual-Purpose Port LEDs
Figure 1-9 shows the LEDs on a dual-purpose port. You can configure each port as either a
10/100/1000BASE-T port through the RJ-45 connector or as an SFP module, but not both at the same
time. The LEDs show how the port is being used (Ethernet or SFP module).
The LED colors have the same meanings as described in Tab le 1- 9.
Figure 1-9Dual-Purpose Port LEDs
Chapter 1 Product Overview
1Dual-purpose port LEDs
1-18
Cisco IE 2000 Switch Hardware Installation Guide
OL-25818-04
Chapter 1 Product Overview
PoE Status LED
Front Panel
The PoE STATUS LED is located on the front panel of the IE 2000 switch models that are equipped with
PoE ports.The LED displays the functionality and status of the PoE ports. The LED colors and meanings
are listed in Table 1-1 0.
Table 1-10PoE Status LED Colors and Meanings
ColorPoE Status
OffPoE is off. If the powered device is receiving power from a non-PoE power source,
the port LED is off even if the powered device is connected to the switch port.
GreenPoE is on. The port LED is green only when the PoE port is providing power.
Alternating green
and amber
Flashing amberPoE is off due to a fault.
PoE is denied because providing power to the powered device will exceed the switch
power capacity.
CautionNoncompliant cabling or powered devices can cause a PoE port fault. Use
only standard-compliant cabling to connect Cisco prestandard IP Phones
and wireless access points or IEEE 802.3af-compliant devices. You must
remove any cable or device that causes a PoE fault.
AmberPoE for the port is disabled. (PoE is enabled by default.)
Flash Memory Card
The switch supports a flash memory card that makes it possible to replace a failed switch without
reconfiguring the new switch. The slot for the flash memory card is on the front of the switch. See
Figure 1-10.
The flash card is hot swappable and can be accessed on the front panel. A cover protects the flash card
and holds the card firmly in place. The cover is hinged and closed with a captive screw. This prevents
the card from coming loose and protects against shock and vibration.
NoteFor more information on inserting and removing the flash memory card, see the “Installing or Removing
the Flash Memory Card (Optional)” section on page 2-7.
OL-25818-04
Cisco IE 2000 Switch Hardware Installation Guide
1-19
Front Panel
331548
16TC
±12/24/48
0.5-3.0A
Chapter 1 Product Overview
Figure 1-10Flash Memory Card Slot
NoteThe replacement SD card part number is SD-IE-1GB.
Cisco IE 2000 Switch Hardware Installation Guide
1-20
OL-25818-04
Chapter 1 Product Overview
331552
1
Rear Panel
Rear Panel
The rear panel of the switch has a latch for installation on a DIN rail. See Figure 1-11. The latch is
spring-loaded to move down to position the switch over a DIN rail and return to the original position to
secure the switch to a DIN rail.
Figure 1-11Cisco IE 2000 Switch Rear Panel
1Latch
Management Options
The switch supports these management options:
• Cisco Network Assistant
Cisco Network Assistant is a PC-based network management GUI application optimized for LANs
of small- and medium-sized businesses. Using the GUI, you can configure and manage switch
clusters or standalone switches. Cisco Network Assistant is available at no cost and can be
downloaded from this URL:
For information on starting the Cisco Network Assistant application, see the Getting Started with Cisco Network Assistant guide on Cisco.com.
• Device Manager
You can use Device Manager, which is in the switch memory, to manage individual and standalone
switches. This web interface offers quick configuration and monitoring. You can access Device
Manager from anywhere in your network through a web browser. For more information, see the
getting started guide and the Device Manager online help.
OL-25818-04
Cisco IE 2000 Switch Hardware Installation Guide
1-21
Network Configurations
Chapter 1 Product Overview
• Cisco IOS CLI
The switch CLI is based on Cisco IOS software and is enhanced to support desktop-switching
features. You can fully configure and monitor the switch. You can access the CLI either by
connecting your management station directly to the switch management port, or a console port, or
by using Telnet from a remote management station. See the switch command reference on
Cisco.com for more information.
• Cisco Prime LAN Management Solution 4.2
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/device_su
pport/table/lms42sdt.html#Cisco IE 2000 Series Switches
• SNMP network management
You can manage switches from a SNMP-compatible management station that is running platforms
such as HP OpenView or SunNet Manager. The switch supports a comprehensive set of Management
Information Base (MIB) extensions and four Remote Monitoring (RMON) groups. See the switch
software configuration guide on Cisco.com and the documentation that came with your SNMP
application for more information.
• Common Industrial Protocol
The Common Industrial Protocol (CIP) management objects are supported. The Cisco IE 2000 can
be managed by CIP-based management tools, allowing the user to manage an entire industrial
automation system with one tool.
• PROFINET TCP/IP and RT
This switch supports PROFINET TCP/IP and RT and can be managed by Siemens' automation
software such as STEP 7.
Network Configurations
See the switch software configuration guide on Cisco.com for network configuration concepts and
examples of using the switch to create dedicated network segments and interconnecting the segments
through Gigabit Ethernet connections.
1-22
Cisco IE 2000 Switch Hardware Installation Guide
OL-25818-04
Loading...
+ 80 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.