Cisco CIVS-IPC-2600 User Manual
Cisco Video Surveillance 2600 IP Camera
User Guide
Model CIVS-IPC-2600
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-24127-02
NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED
WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, the Cisco logo, DCE, and Welcome to the Human Network
are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To
You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco
Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare,
GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime
Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert,
StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates
in the United States and certain other countries.
All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0809R)
Cisco Video Surveillance 2600 IP Camera User Guide
Copyright © 2010 Cisco Systems, Inc. All rights reserved.
IMPLIED, INCLUDING, WITHOUT
Preface
Overview
This document, Cisco Video Surveillance IP Camera User Guide provides information about installing,
configuring, using, managing, and troubleshooting the Cisco Video Surveillance 2600 IP Camera model,
model
Organization
CIVS-IPC-2600
This manual is organized as follows:
Chapter 1, “Overview” Provides an overview of the IP camera and its features
Chapter 2, “Getting Started” Provides instructions for installing and performing
the initial setup of the IP camera, connecting to the IP
camera so that you can configure it or view video
from it, powering the IP camera on and off, resetting
the IP camera, and adjusting its back focus
Chapter 3, “Configuring and Managing the IP
Camera”
Chapter 4, “Viewing Live Video” Explains how to view live video from the IP camera
Chapter 5, “Troubleshooting” Provides basic troubleshooting information
Explains how to configure, manage, and administer
the IP camera through the web-based interface
Obtaining Documentation, Obtaining Support, and Security
Guidelines
For information about obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s
revised Cisco
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS version 2.0.
technical documentation, at:
New in Cisco Product Documentation, which also lists all new and
OL-24127-02
Cisco Video Surveillance 2600 IP Camera User Guide
v
Preface
vi
Cisco Video Surveillance 2600 IP Camera User Guide
OL-24127-02
CONTENTS
Preface v
Overview v
Organization v
Obtaining Documentation, Obtaining Support, and Security Guidelines v
CHAPTER
CHAPTER
CHAPTER
1 Overview 1-1
Features 1-1
IP Camera Overview 1-2
Physical Details 1-2
DC Auto Iris Lens Connector Pinouts 1-6
Package Contents 1-6
2 Getting Started 2-1
Installing the Cisco Video Surveillance IP Camera 2-1
Performing the Initial Setup of the IP Camera 2-4
Accessing the IP Camera Windows 2-6
Adjusting Back Focus on the IP Camera 2-7
Powering the IP Camera On or Off 2-8
Resetting the IP Camera 2-8
Cleaning the IP Camera 2-9
3 Configuring and Managing the IP Camera 3-1
OL-24127-02
Configuration Overview 3-1
Navigating the Configuration Windows 3-4
Setup Windows 3-5
Basic Setup Window 3-5
Advanced Setup Window 3-7
IP Filter Window 3-10
EAPOL Window 3-11
Administration Windows 3-12
Users Window 3-12
Maintenance Window 3-14
Firmware Window 3-15
Cisco Video Surveillance 2600 IP Camera User Guide
iii
Contents
Audio/Video Windows 3-16
Video Window 3-16
Audio Window 3-23
Privacy Region Window 3-24
Security Windows 3-25
Product Process Window 3-25
Initialization Window 3-25
Complexity Window 3-26
Applications Windows 3-27
Mail & FTP Window 3-27
Motion Detection Window 3-29
Event Window 3-30
SNMP Window 3-33
Alarm I/O Ports Window 3-34
PTZ (RS-485) Window 3-35
Preset Positions Window 3-36
CHAPTER
CHAPTER
APPENDIX
I
NDEX
Status Windows 3-38
System Window 3-38
Audio/Video Window 3-39
Network Window 3-40
Syslog & Log Window 3-40
Video Log Window 3-46
4 Viewing Live Video 4-1
Viewing Video through the Home Window Overview 4-1
Home Window Overview 4-1
Home Window Controls 4-3
Viewing Video through Third-Party Devices or Software 4-6
5 Troubleshooting 5-1
A Using the IP Camera with Cisco VSM A-1
iv
Cisco Video Surveillance 2600 IP Camera User Guide
OL-24127-02
Features
CHAP T E R
1
Overview
This chapter provides an overview of the Cisco Video Surveillance IP Cameras and its features. It
includes these topics:
• Features, page 1-1
• IP Camera Overview, page 1-2
The Cisco Video Surveillance 2600 IP Camera offers a feature-rich digital camera solution for a video
surveillance system. It provides high-quality, bandwidth-efficient video capture and transmission, with
support for D1 resolution, motion-triggered viewing, H.264 encoding, and MPEG-4 encoding. It can be
powered through an external power adapter or by integrated Power over Ethernet (PoE).
In addition, the device provides networking and security capabilities, including multicast support,
hardware-based Advanced Encryption Standard (AES), and hardware-based Data Encryption
Standard/Triple Data Encryption Standard (DES/3DES) encryption.
The IP camera includes the following key features:
OL-24127-02
• Built-in H.264 encoder—An internal H.264 encoder can generate the primary or secondary video
stream.
• Built-in MPEG4 encoder—An internal MPEG4 encoder can generate up to two video streams.
• Built-in MJPEG encoder—An internal MJPEG encoder can generate the primary or secondary
video stream.
• Privacy Regions—Up to four user-defined masking zones that can be used to provide regions of
privacy in the camera field of view. Video within privacy regions is not recorded in the camera, nor
sent in the video stream.
• Day/night switch support—An IR-cut filter provides increased sensitivity in low-light conditions.
• Two-way audio communication—Audio can be encoded with the video. With the internal or
optional external microphone and optional external speaker, you can communicate with people at
the IP camera location while you are in a remote location and viewing images from the IP camera.
• Multi-protocol support—Supports these protocols: DHCP, FTP, HTTP, HTTPS, NTP, RTP, RTSP,
SMTP, SSL/TLS, and TCP/IP.
• Web-based management—You perform ongoing administration and management of the IP camera
through web-based configuration menus.
Cisco Video Surveillance 2600 IP Camera User Guide
1-1
IP Camera Overview
Chapter 1 Overview
• Motion detection—The IP camera can detect motion in up to four designated fields of view by
analyzing changes in pixels and generate an alert if motion is detected.
• Flexible scheduling—You can configure the IP camera to respond to events that occur within a
designated schedule.
• Syslog support—The IP camera can send log data to a Syslog server.
• IP address filter—You can designate IP addresses that can access the IP camera and IP addresses
that cannot access the IP camera.
• User-definable HTTP/ HTTPS port number—Allows you to define the port that is used to
connect to the camera through the Internet.
• DHCP support—The IP camera can automatically obtain its IP addresses in a network in which
DHCP is enabled.
• Network Time Protocol (NTP) support—Allows the IP camera to calibrate its internal clock with
a local or Internet time server.
• Support for C and CS mount lenses—Supports a variety of C and CS mount lenses.
• RS-485/PTZ support—Supports Pelco D protocol, which enables PTZ functions when used with a
supported motorized zoom lens, external pan/tilt mount, and control device.
• Power options—The IP camera model can be powered with 12 volts DC, which is provided through
an optional external power adapter, or through PoE (802.3af), which is provided through a supported
switch.
• Camera access control—You can control access to IP camera configuration windows and live video
by configuring various user types and log in credentials.
• Cisco Media API—The IP camera supports the open, standards based, Cisco Media Application
Programming Interface.
IP Camera Overview
The following sections provide information about the Cisco Video Surveillance IP Camera:
• Physical Details, page 1-2
• DC Auto Iris Lens Connector Pinouts, page 1-6
• Package Contents, page 1-6
Physical Details
The IP camera includes a reset button, built-in microphone, status LEDs, several ports for connecting
external devices, and two threaded mounting holes, one on the bottom and one on the top.
Figure 1-1 and the table that follows describe the items on the front of the IP camera.
1-2
Cisco Video Surveillance 2600 IP Camera User Guide
OL-24127-02
Chapter 1 Overview
IP Camera Overview
Figure 1-1 Front of IP Camera
1 Lens opening The IP camera supports a variety of C and CS mount lenses, which attach
here.
For best performance, Cisco recommends that you use a DC auto iris
lens.
2 Focus ring Allows you to adjust the back focus of the IP camera.
You must loosen the focus ring hex screw on the bottom of the IP camera
before you can rotate the focus ring. For instructions, see the
“Adjusting
Back Focus on the IP Camera” section on page 2-7.
3 Microphone Captures audio.
There also is a connection for an optional external microphone on the rear
of the IP camera.
4 Activity LED (green) Indicates activity as follows:
• Off—No activity
• Blinking—Activity detected
Activity can occur when the IP camera communicates with the network
or when a user views video from the IP camera.
If you check the Enable LED Operations check box in the Basic Setup
window, the Activity LED does not light. For more information see the
“Basic Setup Window” section on page 3-5.
OL-24127-02
Cisco Video Surveillance 2600 IP Camera User Guide
1-3
IP Camera Overview
Chapter 1 Overview
5 Ready LED (amber) Indicates power state as follows:
• On—Power is on
• Off—No power
• Blinking—IP camera is starting up. The start up process takes 15 to
20 seconds.
If you check the Enable LED Operations check box in the Basic Setup
window, the Ready LED does not light. For more information see the
“Basic Setup Window” section on page 3-5.
Figure 1-2 and the table that follows describe the items on the rear of the IP camera.
Figure 1-2 Rear of IP Camera
1-4
1 Reset button Recessed button that reboots the IP camera or resets it to a default
2 Network LED (amber) Indicates information about the network connections as follows:
3 LAN port Accepts a standard LAN cable to connect the IP camera to a
Cisco Video Surveillance 2600 IP Camera User Guide
state. You can use a pin or paper clip to depress it. It can be used
any time that the IP camera is on and can have various effects, as
described in the
• On—LAN connection is detected
• Off—LAN connection is not detected
• Blinking—Data is being transmitted or received via the LAN
“Resetting the IP Camera” section on page 2-8.
connection
10/100BASET hub, router, or switch.
OL-24127-02
Chapter 1 Overview
IP Camera Overview
4 PoE LED (green) Indicates information about PoE as follows:
• On—PoE connection is detected
• Off—PoE connection is not detected
5 Analog video output BNC connector for video output (75 ohm).
6 Speaker output Allows the connection of an optional external speaker through a
standard 3.5 mm mini phone jack.
7 Microphone input Allows the connection of an optional external microphone (with
pre-amplifier) through a standard 3.5 mm mini phone jack.
Microphones that are designed for use with PCs usually are
compatible with this input jack.
Connecting an external microphone disables the internal
microphone on the IP camera.
8 GPIO ports General purpose input/output (GPIO) terminal block that includes
a 2-pin RS-485 port, 2 input ports (labeled DI1, DI2), 2 output
ports (labeled DO1, DO2), and 4 ground ports (labeled GND).
9 Power input Provides for the connection of an optional external 12 V, 1 amp DC
power adapter.
Figure 1-3 and the table that follows describe the items on the side of the IP camera.
Figure 1-3 Side of IP Camera
1 DC auto iris lens connector Connection for cable from DC auto iris lens
2 Lockdown cable slot Connection for Kensington-compatible lockdown equipment
OL-24127-02
Cisco Video Surveillance 2600 IP Camera User Guide
1-5
IP Camera Overview
DC Auto Iris Lens Connector Pinouts
Figure 1-4 and the table that follows describe the pinouts of the DC auto iris lens connector on the IP
camera.
Figure 1-4 DC Auto Iris Lens Connector Pinouts
Pin Function
1 Damp –
2 Damp +
3 Drive +
4 Drive –
Chapter 1 Overview
Package Contents
The the Cisco Video Surveillance IP Camera package includes these items:
• Cisco Video Surveillance 2600 IP Camera Quick Start Guide (qty. 1)
• Regulatory Compliance and Safety Information document (qty. 1)
• Camera (qty. 1)
• 0.9 mm Allen wrench (qty. 1)
• Terminal block for power connection (qty. 1)
• C-mount lens adaptor (qty. 1)
• Snap-on ferrite core (qty. 2)
1-6
Cisco Video Surveillance 2600 IP Camera User Guide
OL-24127-02
CHAP T E R
2
Getting Started
This chapter provides instructions for installing and performing the initial setup of the Cisco Video
Surveillance IP Camera. It also describes how to access the IP camera through a web browser so that you
can configure it or view video from it, and how to perform other important tasks.
This chapter includes these topics:
• Installing the Cisco Video Surveillance IP Camera, page 2-1
• Performing the Initial Setup of the IP Camera, page 2-4
• Accessing the IP Camera Windows, page 2-6
• Adjusting Back Focus on the IP Camera, page 2-7
• Powering the IP Camera On or Off, page 2-8
• Resetting the IP Camera, page 2-8
• Cleaning the IP Camera, page 2-9
Installing the Cisco Video Surveillance IP Camera
This section describes how to install the Cisco Video Surveillance IP camera. Before installing, review
these guidelines:
• The IP camera requires a network cable and a connection to a standard 10/100BaseT hub, router, or
switch. To power the IP camera with Power over Ethernet (PoE), a switch must be 802.3af
compliant.
• If you are using the IP camera on a network connection that does not provide PoE, you must use an
external 12 V power adapter.
• If you are using an external speaker, microphone, input device, output device, or control device, you
must configure additional settings after installing and performing the initial set up of the IP camera
before the external device can fully operate. For detailed information about these settings, see
Chapter 3, “Configuring and Managing the IP Camera.”
• If you do not connect an external device (speaker, microphone, analog video display, input device,
output device, or control device) when you perform the following installation procedure, you can
install any of these devices later.
Warning
Installation of the equipment must comply with local and national electrical codes.
Statement 1074
OL-24127-02
Cisco Video Surveillance 2600 IP Camera User Guide
2-1
Installing the Cisco Video Surveillance IP Camera
Chapter 2 Getting Started
Warning
The power supply must be placed indoors.
Note If you use the IP camera outdoors, place the camera and the power supply in a suitable NEMA
Statement 331
enclosure.
Warning
Warning
Warning
Caution Inline power circuits provide current through the communication cable. Use a minimum 24AWG
This product requires short-circuit (overcurrent) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations.
Statement 1045
This product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source
or an IEC60950 compliant limited power source.
Statement 353
The plug-socket combination must be accessible at all times, because it serves as the main
disconnecting device.
Statement 1019
communication cable.
To install the IP camera, follow the steps in Table 2-1. For illustrations of the connectors and ports that
the steps refer to, see the “IP Camera Overview” section on page 1-2.
.
Ta b l e 2-1 Installing the IP Camera
Action Explanation
Step 1
Step 2
Attach a lens to the lens opening on the IP camera. • If you are using a CS mount lens, screw the lens into
If you are using a DC auto iris lens, connect its cable to
the DC auto iris lens connector on the IP camera.
the lens opening. The IP camera accepts CS-mount
lenses with a lens protrusion of up to 5 mm.
• If you are using a C mount lens, screw the C mount
lens adapter that is supplied with the IP camera into
the lens opening, then screw the lens into the adapter.
Ensure that the lens is clean because any dirt may degrade
the quality of video images.
Note Save the lens opening dust cap and replace the dust
cap if you remove the lens.
For best performance, Cisco recommends that you use a
DC auto iris lens.
2-2
Cisco Video Surveillance 2600 IP Camera User Guide
OL-24127-02
Chapter 2 Getting Started
Table 2-1 Installing the IP Camera (continued)
Action Explanation
Step 3
Optional. If you are going to connect a speaker and/or a
microphone to the IP camera, attach a Snap-on ferrite
core to the speaker and microphone cables.
Step 4
Optional. Connect a speaker to the speaker output jack
on the rear of the IP camera.
Step 5
Optional. Connect a microphone to the microphone
input jack on the rear of the IP camera.
Step 6
Optional. Connect an NTSC or PAL compliant analog
video display device to the video output connector on
the rear of the IP camera.
Step 7
Optional. Use the GPIO ports on the rear of the IP
camera to connect external devices that trigger alarms
(connect through alarm input ports) or respond to alarms
(connect through alarm output ports).
Installing the Cisco Video Surveillance IP Camera
A ferrite core must be attached to the speaker or
microphone cable at approximately 10 inches (25 cm)
away from where the cable connects to the IP camera.
When using a speaker and microphone, a single ferrite
core is used for both cables.
Lift the tabs to open the ferrite core, run the speaker and/or
microphone cables through the center of the core, then
snap the core shut to secure it to the cables.
A speaker plays audio that is captured by a microphone
that is attached to the PC on which you view video from
the camera.
Connecting an external microphone disables the IP camera
internal microphone. Place the external microphone in a
location that allows it to capture the audio that you want.
The microphone must include a pre-amplifier.
This device displays video from the IP camera. The
display does not include the time stamp or text that are
configured for the camera.
You can connect up to two input devices and two output
devices to these ports:
DI1—Alarm input 1
DI2—Alarm input 2
DO1—Alarm output 1
DO2—Alarm output 2
Step 8
Step 9
Step 10
OL-24127-02
Optional. Use the RS485 GPIO ports on the rear of the
IP camera to connect a control device (motorized
housing) that supports the Pelco D protocol.
Attach a Snap-on ferrite core to a category 5 or higher
network cable.
Connect a category 5 or higher network cable to the
LAN port on the back of the camera and to a
10/100BaseT hub, router, or switch.
GND—Ground (for use if needed)
These ports are labeled D+ (data plus) and D– (data
minus) and accept a cable with two conductors. The cable
fits into the ports in one way. Make sure to insert it
properly.
A ferrite core must be attached to the network cable at
approximately 10 inches (25 cm) away from where the
cable connects to the IP camera.
Lift the tabs to open the ferrite core, run the cable through
the center of the core, then snap the core shut to secure it
to the cable.
If your network provides PoE, the IP camera powers on.
Skip to
Step 12.
Cisco Video Surveillance 2600 IP Camera User Guide
2-3
Performing the Initial Setup of the IP Camera
Table 2-1 Installing the IP Camera (continued)
Action Explanation
Step 11
If you are using the IP camera on a network connection
that does not provide PoE, connect an external 12 V
power adapter.
Chapter 2 Getting Started
First, connect the bare wires at the end of the power
adapter to the terminal block that is provided with the IP
camera:
• With the screws on the terminal block facing down,
put the positive wire into the slot at the right rear of
the terminal block and put the negative wire into the
slot on the left.
• Use a small flat-head screwdriver to tighten the
screws on the bottom of the terminal block so that the
power adapter wires are attached securely.
Note The power adapter may include an attached
terminal block that does not fit the IP camera. If
so, remove that terminal block and replace it with
the one that is provided with the IP camera.
Step 12
Step 13
Step 14
Next, plug the terminal block into the power input port on
back of the IP camera. The terminal block fits into the
input port in one way. Make sure that the tabs on the
terminal block face the bottom of the IP camera.
Finally, plug the external power adapter into an electrical
outlet. The IP camera powers up.
Check the LEDs on the IP camera.
• The Ready LED blinks while the IP camera starts up.
After 15 to 20 seconds, startup completes and the
Ready LED should remain on.
• The Network LED should be on.
Mount the IP camera in the desired location. Connect the mounting device to the threaded mounting
hole on the bottom or top of the IP camera, depending on
your installation requirement.
You may first need to remove the rubber protector from the
mounting hole. Place this protector in the unused
mounting hole.
Optional. Use the lockdown cable slot to secure the IP
camera.
You can secure the IP camera to a fixed object by using
Kensington-compatible lockdown equipment
After you install the IP camera, follow the instructions in the “Performing the Initial Setup of the IP
Camera” section on page 2-4 to access and configure the camera.
Performing the Initial Setup of the IP Camera
After you install IP camera, or after you perform a factory reset procedure, you must access the IP
camera and make initial configuration settings. These settings include administrator and root passwords,
and whether the IP camera can be accessed through an HTTP connection in addition to the default
HTTPS (HTTP secure) connection.
Cisco Video Surveillance 2600 IP Camera User Guide
2-4
OL-24127-02
Chapter 2 Getting Started
Step 1 Start Internet Explorer, enter HTTPS://ip_address in the address field, and press Enter.
Performing the Initial Setup of the IP Camera
To make these configuration settings, you connect to the IP camera from any PC that is on the same
network as the IP camera. The PC must meet these requirements:
• Operating system—Microsoft Windows 2000, XP, or Vista
• Browser—Internet Explorer 8.x or later
In addition, you must know the IP address of the IP camera. By default, when the IP camera powers on,
it attempts to obtain an IP address from a DHCP server in your network. If the camera cannot obtain an
IP address through DCHP within 90 seconds, it uses a default IP address of 192.168.0.100.
To connect to the IP camera for the first time and make initial configuration settings, perform the
following steps. You can change these configuration settings in the future as described in the
“Initialization Window” section on page 3-25.
Procedure
Replace ip_address with the IP address that the IP camera obtained through DHCP or, if the camera is
unable to obtain this IP address, enter 192.168.0.100.
The Account window appears.
Step 2 In the Set Password and Verify Password fields in the Admin column, enter a password for the IP camera
administrator.
You must enter the same password in both fields. The password is case sensitive and must contain at least
eight characters, which can be letters, numbers, and special characters, but no spaces. Special characters
are: ! " # $ % & ' ( ) * + , - . : ; < = > ? @ [ \ ] ^ _ ` { | } ~.
Step 3 In the Set Password and Verify Password fields in the Root column, enter a password that is used when
accessing the IP camera through a Secure Shell (SSH) connection.
You must enter the same password in both fields. The password is case sensitive and must contain at least
eight characters, which can be letters, numbers, and special characters, but no spaces. Special characters
are: ! " # $ % & ' ( ) * + , - . : ; < = > ? @ [ \ ] ^ _ ` { | } ~.
You use the root password if you need to troubleshoot the IP camera through a SSH connection with the
assistance of the Cisco Technical Assistance Center.
Step 4 In the HTTP area, click the HTTP radio button if you want to allow both HTTP and HTTPS connections
to the IP camera.
The default setting is HTTPS, which allows only HTTPS (secure) connections to the IP camera.
Step 5 Click Apply.
The IP camera reboots.
Step 6 After the IP camera reboots, start Internet Explorer and, in the Address field, enter the following:
protocol://ip_address
where:
• protocol is HTTPS or HTTP. (You can use HTTP only if you enabled it in Step 4.)
• ip_address is the IP address that you used in Step 1.
OL-24127-02
Step 7 If you are prompted to install ActiveX controls, which are required to view video from the IP camera,
follow the on-screen prompts to do so.
The Main window appears and video from the IP camera starts playing automatically.
You can take these actions in the Main window:
Cisco Video Surveillance 2600 IP Camera User Guide
2-5
Accessing the IP Camera Windows
• Click the Setup link to access configuration menus for the camera. For detailed information about
these menus, see
• Click the Home link to view and control live video from the camera. For detailed information about
these actions, see
• Click the Logout button to exit the window.
Chapter 3, “Configuring and Managing the IP Camera.”
Chapter 4, “Viewing Live Video.”
Accessing the IP Camera Windows
After you perform the initial configuration as described in the “Performing the Initial Setup of the IP
Camera” section on page 2-4, follow the steps in this section each time that you want to access the IP
camera windows to make configuration settings or view live video.
You access these windows by connecting to the IP camera from any PC that is on the same network as
the IP camera and that meets these requirements:
• Operating system—Microsoft Windows 2000, Windows XP, or Vista
• Browser—Internet Explorer 8.x or later
Chapter 2 Getting Started
You need this information to access the IP camera windows:
• IP address of the IP camera. By default, the IP camera attempts to obtain an IP address from a DHCP
server in your network. If the IP camera cannot obtain an IP address through DHCP within 90
seconds of powering up or resetting, it uses the default IP address of 192.168.0.100.
• Port number, if other than the default value. Default port numbers for the IP camera are 443 for
HTTPS and 80 for HTTP. The IP camera administrator can enable an alternative HTTPS port and an
alternative HTTP port as described in the
• Your user name and password for the IP camera. The IP camera administrator configures user names
and passwords as described in the
“Users Window” section on page 3-12.
“Advanced Setup Window” section on page 3-7.
To access the IP camera windows, follow these steps:
Procedure
Step 1 Start Internet Explorer and enter the following in the address field:
protocol://ip_address:port_num ber
where:
• protocol is HTTPS for a secure connection or HTTP for a non-secure connection. You can use
HTTP only if you configure the camera to accept non-secure HTTP connections as described in the
“Performing the Initial Setup of the IP Camera” section on page 2-4.
• ip_address is the IP address of the IP camera. The default IP address is 192.168.0.100.
• port_number is the port number that is used for HTTPS or HTTP connections to the IP camera. You
do not need to enter a port number if you are connecting through the default HTTPS port 443 or the
default HTTP port 80.
2-6
For example,
• Enter the following for a secure connection if the IP address is 192.168.0.100 and the HTTPS port
number is 443:
https://192.168.0.100
Cisco Video Surveillance 2600 IP Camera User Guide
OL-24127-02
Chapter 2 Getting Started
Step 2 Enter your IP camera user name and password when prompted, then click OK.
Adjusting Back Focus on the IP Camera
• Enter the following for a secure connection if the IP address is 203.70.212.52 and the HTTPS port
number is 1024:
https://203.70.212.52:1024
• Enter the following for a non-secure connection if the IP address is 203.70.212.52 and the HTTP
port number is 80:
http://203.70.212.52
• Enter the following for a non-secure connection if the IP address is 203.70.212.52 and the HTTP
port number is 1024:
http://203.70.212.52:1024
To log in as the IP camera administrator, enter the user name admin (all lower case) and the password
that is configured for the administrator. To log in as a user, enter the user name and password that are
configured for the user.
The Main window appears and video from the IP camera starts playing automatically. You can take these
actions in the Main window:
• Click the Setup link to access configuration menus for the camera. For detailed information about
these menus, see
• Click the Home link to view and control live video from the camera. For detailed information about
these actions, see
Chapter 3, “Configuring and Managing the IP Camera.”
Chapter 4, “Viewing Live Video.”
• Click the Logout button to exit the window.
Adjusting Back Focus on the IP Camera
To obtain the sharpest image from the camera, you may need to adjust its back focus. This adjustment is
useful if the focus control on a lens does not allow you to obtain a sharp enough image.
To adjust the back focus, perform the following steps while viewing video from the camera. For
information about viewing video, see
Procedure
Step 1 With a lens attached to the IP camera, use the 0.9 mm Allen wrench that is supplied with the IP camera
to loosen the focus ring hex screw.
This screw is on the bottom of the camera just behind the focus ring.
Step 2 Adjust the back focus by aiming the IP camera at an object that is at least 15 feet (4.5 meters) away and
rotating the focus ring to obtain a clear image as follows:
• For a variable-focus lens, obtain a sharp picture in both wide-angle and telephoto positions.
• For a zoom lens, ensure that the object of interest remains in focus throughout the entire zoom range
of the lens.
Step 3 Use the Allen wrench to tighten the focus ring hex screw.
Chapter 4, “Viewing Live Video.”
OL-24127-02
Cisco Video Surveillance 2600 IP Camera User Guide
2-7
Powering the IP Camera On or Off
Powering the IP Camera On or Off
The IP camera does not include an on/off switch. You power it on or off by connecting it to or
disconnecting it from a power source. When you power off the IP camera, it retains configuration
information.
To power on the IP camera, take either of these actions:
• Use an STP category 5 or higher network cable to connect the IP camera to a network switch that
provides 802.3af compliant PoE
• Use an external 12 V power adapter to connect the IP camera to a wall outlet
To power off the IP camera, take either of these actions:
• If the IP camera is receiving PoE, disconnect the network cable
• If the IP camera is receiving power through the power adapter, unplug the adapter from the wall or
disconnect it from the camera
Resetting the IP Camera
Chapter 2 Getting Started
You reset the IP camera by pressing the Reset button on the rear of the device (see Figure 1-2 on
page 1-4).
There are various reset types, as described in Tab le 2-2.
You also can perform some reset operations from the Maintenance window as described in the
“Maintenance Window” section on page 3-14.
Ta b l e 2-2 Resetting the IP Camera
Reset Type Procedure Remarks
Reboot. Press and immediately release
the Reset button.
IP address reset. Press and hold the Reset button
for at least 1 second but no more
than 9 seconds.
Factory reset. Press and hold the button for at
least 10 seconds.
This action is equivalent to
powering the IP camera down
and then powering it up. Settings
that are configured for the IP
camera are retained.
If DHCP is enabled in your
network, the IP camera obtains
an IP address from the DHCP
server. Otherwise, after 90
seconds, the IP camera IP
address resets to the default
address of 192.168.0.100. All
other configuration settings are
retained.
Sets all IP camera options to
their default values. After you
perform this procedure, follow
the steps in the
Initial Setup of the IP Camera”
section on page 2-4.
“Performing the
2-8
Cisco Video Surveillance 2600 IP Camera User Guide
OL-24127-02
Chapter 2 Getting Started
Cleaning the IP Camera
To clean and IP camera, follow these guidelines:
• To clean the IP camera housing, use a clean, dry, soft cloth to gently wipe the surface of the housing
• To clean the lens, use only tissue paper or solution that is designed for high quality optical lenses.
Cleaning the IP Camera
OL-24127-02
Cisco Video Surveillance 2600 IP Camera User Guide
2-9
Cleaning the IP Camera
Chapter 2 Getting Started
2-10
Cisco Video Surveillance 2600 IP Camera User Guide
OL-24127-02
CHAP T E R
3
Configuring and Managing the IP Camera
The Cisco Video Surveillance IP Camera provides configuration windows that you use to configure and
manage the IP camera. This chapter explains how to access the configuration windows, describes each
window, and provides detailed information about the options that are available in each window.
When configuring the IP camera, be aware of these guidelines:
• You must install and set up the Cisco Video Surveillance IP camera as described in Chapter 2,
“Getting Started,” before you can access the configuration menus.
• You must be an IP camera administrator or an IP camera user with administrator privileges to access
the configuration windows.
• For security, the configuration windows time out after 2 minutes of no activity. If a time out occurs,
a pop-up window prompts you to log back in by entering your user name and password when you
next press a key or click an item. When you log back in, the configuration window that you were
displaying remains on your screen, but all settings revert to their last saved values.
This chapter includes these topics:
• Configuration Overview, page 3-1
• Navigating the Configuration Windows, page 3-4
• Setup Windows, page 3-5
• Administration Windows, page 3-12
• Audio/Video Windows, page 3-16
• Security Windows, page 3-25
• Applications Windows, page 3-27
• Status Windows, page 3-38
Configuration Overview
There are many settings and options that you can configure for the IP camera. The items that you
configure depend on several factors, including your camera model, operational requirements, and
connected external devices.
Table 3-1 provides general information to help you determine what items you need to configure for your
situation. Use this table as a guide as you configure your IP camera and as a reference if you need to
change configurations in the future.
OL-24127-02
Cisco Video Surveillance 2600 IP Camera User Guide
3-1
Chapter 3 Configuring and Managing the IP Camera
Configuration Overview
Ta b l e 3-1 Guidelines for Configuring the IP Camera
Configuration Item Explanation Guidelines for Use Reference
IP camera name and
description
LED operation Determines whether the LEDs
Time information Sets the date and time for the IP
Network options Determine how the IP camera
Advanced network
and protocol options
IP address filters Controls access to the IP camera
EAPOL Configures Extensible
IP camera users Sets the password for the IP
Video options Sets video resolution and quality,
Identifies the IP camera. Recommended. See the “Basic Setup Window”
section on page 3-5.
Optional. See the “Basic Setup Window”
on the front of the IP camera
section on page 3-5.
light or remain off.
Recommended. See the “Basic Setup Window”
camera. Also determines how the
section on page 3-5.
IP camera obtains the date and
time, its time zone, and whether
it adjusts for daylight saving
time.
obtains its IP address, and
provides options for configuring
subnet mask, gateway, and DNS
IP address is required if DHCP is
not enabled in your network,
other items depend on your
network configuration.
See the “Basic Setup Window”
section on page 3-5.
servers.
Determine whether the IP
camera uses Cisco Discovery
Optional, depending on your
network and requirements.
See the “Advanced Setup
Window” section on page 3-7.
Protocol (CDP) and it uses
Bonjour, configure alternate
ports for HTTP or HTTPS
connections, configure RTP or
RTSP options, and configure
QoS.
Optional. See the “IP Filter Window”
by IP address.
section on page 3-10.
Optional. See the “EAPOL Window”
Authentication Protocol Over
section on page 3-11.
LANs (EAPOL) for
authenticating and controlling
user traffic to a protected
network
Optional. See the “Users Window” section
camera administrator, and sets
on page 3-12.
log in credentials and privileges
for up to 20 users.
whether you use one or two
Optional, depending on your
requirements.
See the “Video Window” section
on page 3-16.
video streams, streaming mode,
picture appearance, whether
video includes a time stamp or
text overlay, and how the IP
camera handles day and night
vision modes.
3-2
Cisco Video Surveillance 2600 IP Camera User Guide
OL-24127-02
Chapter 3 Configuring and Managing the IP Camera
Configuration Overview
Table 3-1 Guidelines for Configuring the IP Camera (continued)
Configuration Item Explanation Guidelines for Use Reference
Audio options Includes options for audio
streams that are received or sent
by the IP camera.
Privacy regions Creates up to four user-defined
masking zones that can be used
to provide regions of privacy in
the camera field of view. Video
within privacy regions is not
recorded in the camera, nor sent
in the video stream.
Security options Lets you stop IP camera
processes, configure
administrator and root password
requirements, and allow access
to the IP camera through HTTP
or Secure Shell (SSH)
connections.
Mail and FTP
options
Determines whether and how the
IP camera notifies you when an
event occurs.
Motion detection Determines whether and how the
IP camera detects activity in its
field of view, which in turn can
generate an alert.
Event handling Determines actions that the IP
camera takes when it detects an
event. An event can be motion
that is detected in the field of
view or a state change that is
detected on and input port.
SNMP options Configure SNMP settings. Optional. See the “SNMP Window”
I/O ports options Set the default states for the IP
camera input and output ports,
how the ports respond to events,
and how the ports respond to
manual control.
Pan, tilt, zoom
options
Patrol sequence
options
Enable PTZ functions for the IP
camera.
Define a preset position and
patrol sequence for the IP
camera.
Required if you use the internal
or an external microphone, or an
See the “Audio Window” section
on page 3-23.
external speaker.
Optional. See the “Privacy Region
Window” section on page 3-24.
Optional. See the “Security Windows”
section on page 3-25.
Required if you want the IP
camera send e-mail notification
See the “Mail & FTP Window”
section on page 3-27.
of an event.
Optional. See the “Motion Detection
Window” section on page 3-29.
Optional. See the “Event Window” section
on page 3-30.
section on page 3-33.
Required if you connect devices
through the IP camera input or
See the “Alarm I/O Ports
Window” section on page 3-34.
output ports.
Required to control PTZ
functions.
See the “PTZ (RS-485)
Window” section on page 3-35
Optional. See the “PTZ (RS-485)
Window” section on page 3-35
and the “Preset Positions
Window” section on page 3-36.
OL-24127-02
Cisco Video Surveillance 2600 IP Camera User Guide
3-3
Chapter 3 Configuring and Managing the IP Camera
Navigating the Configuration Windows
Table 3-1 Guidelines for Configuring the IP Camera (continued)
Configuration Item Explanation Guidelines for Use Reference
Log file options Control which log information
the IP camera captures and
Recommended. See the “Syslog & Log Window”
section on page 3-40.
whether it sends the log file to a
Syslog server.
Video log options Let you manage the IP camera
video log.
Recommended. See the “Video Log Window”
section on page 3-46.
Navigating the Configuration Windows
After you access the configuration windows as described in the “Accessing the IP Camera Windows”
section on page 2-6, a window appears that includes the following components:
• Navigation tree—Appears at the left of the window and provides links to each configuration window
• Basic Setup window—Appears at the right of the window
The navigation tree always appears. The right area varies depending on the configuration window that
you choose from the navigation tree.
You can perform the following activities from when any configuration window is displayed:
• Click the Home link at the top of the Navigation Tree to display live video from the IP camera. For
related information, see
• Click the Logout button to exit the Main window and close your web browser.
• Use the Navigation Tree to access each configuration window. To do so, click the link or the right
arrow
next to the link for the group of configuration windows that you want. The name of each
Chapter 4, “Viewing Live Video.”
associated window appears as a link. Then click the link for the desired window.
To collapse a set of links, click the down arrow next to the top-level link.
The configuration windows are organized as follows:
• Setup
–
Basic Setup
–
Advanced Setup
–
IP Filter
–
EAPOL
• Administration
–
Users
–
Maintenance
–
Firmware
• Audio/Video
–
Vid e o
–
Audio
–
Privacy Region
3-4
Cisco Video Surveillance 2600 IP Camera User Guide
OL-24127-02
Chapter 3 Configuring and Managing the IP Camera
• Security
–
Product Process
–
Initialization
–
Complexity
• Applications
–
Mail & FTP
–
Motion Detection
–
Event
–
SNMP
–
Alarm I/O Ports
–
PTZ (RS-485)
• Status
–
System
–
Audio Video
–
Network
Setup Windows
–
Syslog & Log
–
Video Log
Setup Windows
The Setup windows let you configure a variety of basic and advanced settings for the IP camera, and to
designate IP addresses that are allowed or denied access to the IP camera.
The following sections describe the Setup windows in detail:
• Basic Setup Window, page 3-5
• Advanced Setup Window, page 3-7
• IP Filter Window, page 3-10
• EAPOL Window, page 3-11
Basic Setup Window
The Basic Setup window provides options for configuring device and network settings for the IP camera.
To display the Basic Setup window, access the configuration windows as described in the “Accessing the
IP Camera Windows” section on page 2-6, click Setup, then click Basic Setup.
If you change any options except the Current Date/Time in the Basic Setup window, you must click Save
to save the changes. To discard the changes, click Cancel before clicking Save. These buttons appear at
the bottom of the window. You may need to scroll down to see them.
OL-24127-02
Cisco Video Surveillance 2600 IP Camera User Guide
3-5
Setup Windows
Chapter 3 Configuring and Managing the IP Camera
Table 3-2 describes the options in the Basic Setup window.
Ta b l e 3-2 Basic Setup Window Options
Option Description
Device Settings
Device ID Display only. Unique identifier of the IP camera. The device ID is configured
for the IP camera at the factory.
Camera Name Enter a name for the IP camera. This name appears in the video log if an
event occurs. (For related information, see the
on page 3-46.)
The camera name can include any combination of up to 15 letters and
numbers. Cisco recommends that you give each IP camera a unique name so
that you can identify it easily.
Description Enter a description of the IP camera. For example, enter the IP camera
location, such as “North Entrance.”
The description can include any combination of up to 32 letters, numbers,
and spaces.
Enable LED Operations Check this check box if you want the Ready LED or Activity LED on the
front of the IP camera to light when the IP camera receives power or
performs an activity.
If you do not check this check box, these LEDs do not light.
Current Date/Time Display only. Current date and time of the internal clock of the IP camera.
“Video Log Window” section
To change the date or time, click Change to display the Set Date/Time
window, then take the appropriate action:
• To synchronize the IP camera date and time with the date and time of the
PC that you are using, click Sync with PC.
• To set the IP camera date and time to any values, enter the values in the
New Date and New Time fields, then click Set New Time.
• To exit the Date/Time window, click Close.
Time Zone From the drop-down list, choose the time zone in which the IP camera is
located.
The time that appears when you view video from this IP camera reflects this
time zone.
Adjust for Daylight
Saving Time
Check here if you want
to update the time
automatically from the
NTP server from the
Internet
Check this check box if you want the time of the IP camera to adjust
automatically for daylight saving time.
Check this check box if you want the IP camera to obtain its time from a
network time protocol (NTP) server.
If you check this check box, the camera contacts the designated NTP server
every 64 seconds and synchronizes its internal clock with the time of that
server.
NTP Server Address If you configured the IP camera to obtain its time from an NTP server, enter
the IP address of the NTP server.
3-6
Cisco Video Surveillance 2600 IP Camera User Guide
OL-24127-02
Loading...