CISCO AIR-ANT1728 User Manual [fr]
Cisco Aironet High Gain Omnidirectional
Ceiling Mount Antenna (AIR-ANT1728)—
Antenne Cisco Aironet omnidirectionnelle à
gain élevé montée au plafond (AIR-ANT1728)
2
78-14721-02A0
Cisco Aironet High Gain Omnidirectional Ceiling Mount Antenna (AIR-ANT1728)
Overview
This document outlines the specifications, describes the high gain omnidirectional ceiling mount
antenna, and provides instructions for mounting it on a suspended ceiling track. Designed for WLAN
applications operating in the 2.4- to 2.5-GHz frequency range, the antenna has a nominal gain of 5.2 dBi.
The antenna is used primarily with access points, but is compatible with Cisco Aironet radio products
utilizing a reverse-polarity threaded Neil Concelman (RP-TNC) connector.
Technical Specifications
ENGLISH
Antenna type Dipole
Operating frequency range 2.4- to 2.483-GHz
VSWR Less than 2:1, 1.5:1
nominal
Gain 5.2 dBi
Polarization Vertical
E-Plane (3dB bandwidth) 40 degrees
H-Plane (3dB bandwidth) Omnidirectional
Cable length and type 3 ft (0.91 m)
Plenum rated RG-58
Dimensions (H x W) 11.5 in. x 1.25 in.
(29.2 cm x 3.2 cm)
Weight 4.6 oz (131 g)
78-14721-02A0
Cisco Aironet High Gain Omnidirectional Ceiling Mount Antenna (AIR-ANT1728)
3
ENGLISH
E-Plane Pattern H-Plane Pattern
System Requirements
This antenna is designed for use with Cisco Aironet access points, but can be used with any 2.4-GHz
Cisco Aironet radio device that utilizes a RP-TNC connector.
Installation Notes
Choosing a Mounting Location
The location of the antenna is important. Objects such as metal columns, walls, etc. will reduce
efficiency. Best performance is achieved when transmit and receive antennas are mounted at the same
height and in a direct line of sight with no obstructions. If this is not possible and reception is poor, you
should try different mounting positions to optimize reception.
The antenna is designed to attach to and hang from a standard suspended ceiling track having a width
from 13/16 inches (20.6 millimeters) to 1 1/4 inches (31.7 millimeters).
Tools and Equipment Required
To install the antenna on a suspended ceiling track, you will need the following tools and equipment.
• A ceiling track bracket (shipped with your antenna)
• A 7/16 inch (11.1 millimeters) wrench
• Cable ties or electrical tape
The following sections contain procedures for installing the antenna to a suspended ceiling track.
Cisco Aironet High Gain Omnidirectional Ceiling Mount Antenna (AIR-ANT1728)
4
78-14721-02A0
Installing the Antenna
78372
Follow these steps to install the antenna on a suspended ceiling track.
Step 1 Determine the location you wish to mount the antenna.
Step 2 Loosen the hex nut on the ceiling track bracket.
Step 3 Position the bracket on the ceiling track. See Figure 1.
Figure 1 Positioning the Ceiling Track Bracket
ENGLISH
Step 4 Squeeze the bracket firmly onto the ceiling track.
Step 5 Use a 7/16 inch (11.1 millimeter) wrench to tighten the hex nut. Do not overtighten.
Step 6 Carefully screw the antenna onto the bracket’s threaded stud until it is hand tight. See Figure 2.
Figure 2 Attaching the Antenna
78-14721-02A0
Cisco Aironet High Gain Omnidirectional Ceiling Mount Antenna (AIR-ANT1728)
5
Loading...