Cisco 860 Series, 880 Series, 890 Series Hardware Installation Manual

Download

Page 1

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Last Revised: March 6, 2013 Text Part Number: OL-16215-10

Page 2

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

• Turn the television or radio antenna until the interference stops.

• Move the equipment to one side or the other of the television or radio.

• Move the equipment farther away from the television or radio.

• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:

www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership

relationship between Cisco and any other company. (1110R)

IMPLIED, INCLUDING, WITHOUT

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

Page 3

CONTENTS

Preface vii

Objective vii

Audience vii

Organization viii

Conventions viii

Related Documentation

In addition to the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISR Hardware Installation Guide (this document), the Cisco

set includes the following documents:

• Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers

• Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Software

Configuration Guide

• Software Activation on Cisco Integrated Services Routers and Cisco Integrated Service Routers G2

• Cisco IOS Software Activation Configuration Guide

• Declarations of Conformity and Regulatory Information for Cisco Access Products with 802.11a/b/g

and 802.11b/g Radios

Statement 1004

860 series, Cisco 880 series, and Cisco 890 series ISR documentation

• Cisco IOS Release Notes

• Cisco IOS Quality of Service Solutions Command Reference, Release 12.4T

• Cisco IOS Security Configuration Guide, Release 12.4T

• Cisco IOS Security Command Reference, Release 12.4T

• Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges, versions 12.4(10b) JA

and 12.3(8) JEC

• Wireless LAN Controllers

• Unified Wireless LAN Access Points

• Cisco IOS Voice Port Configuration Guide

• SCCP Controlled Analog (FXS) Ports with Supplementary Features in Cisco IOS Gateways

• Cisco CP Express User’s Guide

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Page 16

Searching Cisco Documents

To search a HTML document using a web browser, press Ctrl-F (Windows) or Cmd-F (Apple). In most browsers, the option to search whole words only, invoke case sensitivity, or search forward and backward is also available.

To search a PDF document in Adobe Reader, use the basic Find toolbar (Ctrl-F) or the Full Reader Search window (Shift-Ctrl-F). Use the Find toolbar to find words or phrases within a specific document. Use the Full Reader Search window to search multiple PDF files simultaneously and to change case sensitivity and other options. Adobe Reader’s online help has more information about how to search PDF documents.

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s revised Cisco

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as an RSS feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supports RSS

technical documentation:

Ve r si o n 2.0.

New in Cisco Product Documentation, which also lists all new and

Preface

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

xvi

OL-16215-10

Page 17

CHAP T ER

Product Overview

This chapter provides an overview of the features available for the Cisco 860 series, Cisco 880 series, and Cisco

• General Description, page 1-2

• Cisco 860 Series ISRs, page 1-2

• Cisco 860VAE Series ISRs, page 1-3

• Cisco 880 Series ISRs, page 1-6

• Cisco 890 Series ISRs, page 1-17

• Hardware Features, page 1-27

Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap

that ships with the router and

SOHO Series Routers.

890 series Integrated Services Routers (ISRs), and contains the following sections:

Regulatory Compliance and Safety Information for Cisco 800 Series and

OL-16215-10

Note Some illustrations in this document show a wireless router. Both wireless and nonwireless models are

available in the Cisco are similar for both wireless and nonwireless routers.

Note Throughout this document the term VDSL refers to support for VDSL2 (ITU G.993.2) and ADSL refers

to support for ADSL, ADSL2, & ADSL2+ (ITU G.992.1, G.992.3, & G.992.5).

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

860 series, Cisco 880 series, and Cisco 890 series ISRs. Port and feature locations

1-1

Page 18

General Description

The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs provide data, voice, Wi-Fi CERTIFIED™ wireless access point (AP), integrated Virtual Private Network (VPN), and backup capabilities to corporate teleworkers and to remote and small offices with fewer than 20 users. These routers are capable of bridging and multiprotocol routing between LAN and WAN ports. The routers provide advanced features, such as high speed DSL (G.SHDSL, ADSL, or VDSL), 802.11n, quality of service (QoS), firewall, antivirus protection, and Secure Socket Layer (SSL). The Cisco 860VAE, 886VA and 887VA series routers have the additional capability of DSL Multi-mode (VDSL/ADSL).

The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs have a desktop form factor with built-in wall-mount features. The Cisco 890 series ISRs also have optional rack-mount features. These ISRs are powered by an external power supply adapter. The various models differ in the WAN interface and features that they support.

Cisco 860 Series ISRs

The Cisco 860 series ISRs are fixed-configuration data routers that support the following features:

Chapter 1 Product Overview

• An integrated 4-port 10/100 Ethernet switch for connecting to the LAN

• A10/100 Fast Ethernet (FE) port for connecting to the WAN.

• Optional, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP

Figure 1-1 shows the front panel details of the Cisco 860 wireless router.

Figure 1-1 Front Panel of the Cisco 860 Series Wireless ISR

231969

1 LEDs

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-2

OL-16215-10

Page 19

Chapter 1 Product Overview

232181

31 4 6 7 852

WAN

FE 4

Cisco 861W

Figure 1-2 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do

not have antennas on the back panel. However, the feature locations are similar for all Cisco 860 series routers.

Figure 1-2 Back Panel of the Cisco 861W ISR

Cisco 860VAE Series ISRs

1 Primary WAN port—10/100 5 Reset button 2 Antenna—captive omnidirectional dipole

WLAN antenna (wireless models only)

3 4-port 10/100 Ethernet switch 7 Earth ground connection 4 Serial port—console or auxiliary 8 Kensington security slot

Cisco 860VAE Series ISRs

The Cisco 860VAE series ISRs are fixed-configuration data routers. This section describes the features of the products in this series.

Interfaces

Table 1-1 describes the interfaces of the Cisco 860VAE series routers.

Ta b l e 1-1 Interfaces of the Cisco 860VAE Series ISRs

Interfaces

4 FE1 switch ports x x x x

1 GE2 switch port — — x x

1 GE WAN port x x x x

6 Power connector

Model

866VAE 867VAE 866VAE-K9 867VAE-K9

OL-16215-10

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-3

Page 20

Cisco 860VAE Series ISRs

246199

Cisco 860 Series

Note The Cisco 866VAE, 867VAE, 866VAE-K9, and 867VAE-K9 routers each have two WAN ports. Only one

IOS Images

Chapter 1 Product Overview

Table 1-1 Interfaces of the Cisco 860VAE Series ISRs (continued)

Model

Interfaces

1 VDSL/ADSL over POTS port — x — x

1 VDSL/ADSL over ISDN port x — x —

1. FE = Fast Ethernet

2. GE = Gigabit Ethernet

of the two ports can be active at any given time.

Table 1-2 describes the IOS images included in Cisco 860VAE series routers.

866VAE 867VAE 866VAE-K9 867VAE-K9

Ta b l e 1-2 IOS Images of the Cisco 860VAE Series ISRs

Model

IOS Image

866VAE 867VAE 866VAE-K9 867VAE-K9

c860vae-ipbasek9-mz x x — —

c860vae-advsecurityk9-mz — — x x

c860vae-advsecurityk9_npe-mz — — x x

Figure 1-3 shows the front panel details of the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and

Cisco 867VAE-K9 integrated services routers (ISRs).

Figure 1-3 Front Panel of the Cisco 860VAE series ISR

1 LEDs

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-4

OL-16215-10

Page 21

Chapter 1 Product Overview

246200

CONSOLE

AUX

FE 2 FE 1 FE 0FE 3OVER ISDN

LAN

WAN

GE0

VDSL/ADSL

12V 2.5A

RESET

Cisco 866VAE

1 2 3 4 7 8 95 6

284558

CONSOLE

AUX

OVER POTS

WAN LAN

GE1 GE0 FE3 FE2 FE1 FE0

VDSL/ADSL

12V 2.5A

RESET

Cisco 867VAE-K9

1 2 3 4 7 8 95 6

Figure 1-4 shows the back panel details of the Cisco 866VAE ISR.

Figure 1-4 Back Panel of the Cisco 866VAE ISR

Cisco 860VAE Series ISRs

1 xDSL port

6 On/Off switch 2 GE WAN interface 7 Power connector 3 Ethernet LAN FE interfaces (FE0 through

8 Reset button

FE3 interfaces)

4 USB port 9 Kensington security slot 5 Serial port—console or auxiliary

1. Using RJ-11.

Figure 1-5 shows the back panel details of the Cisco 867VAE-K9.

Figure 1-5 Back Panel of the Cisco 867VAE-K9 ISR

1 xDSL port 6 On/Off switch 2 GE WAN interface 7 Power connector 3 Ethernet LAN GE and FE interfaces (GE0

interface and FE0 through FE3 interfaces)

4 USB port 9 Kensington security slot 5 Serial port—console or auxiliary

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

8 Reset button

1-5

Page 22

Cisco 880 Series ISRs

The Cisco 880 series ISRs have data and voice capabilities. They have the following features:

• Integrated 4-port 10/100 Ethernet switch for connecting to the LAN

• 10/100 FE, VDSLoPOTS, ADSL over POTS, ADSL over ISDN, DSL Multi-mode

(VDSL/ADSLoPOTS, VDSL/ADSLoISDN Cisco VA models only), or G.SHDSL port for connecting to the WAN

• Optional embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP

• Optional 2-port Power over Ethernet (PoE)

Note The Cisco 880 series ISRs can include an optional PoE module that provides power to

802.3af-compliant devices connected to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and install it to enable the PoE function.

• DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB

system memory

The following features are located on the front panel:

• USB 1.1 port

Chapter 1 Product Overview

• Express card slot for third-generation (3G) cellular data WAN connectivity, available only on the

Cisco 880G models

This section contains the following topics:

• Cisco 880 Series Data Routers, page 1-6

• Cisco 880 Series Voice and Data Routers, page 1-9

• Cisco 880 Series with Embedded WLAN Antennas, page 1-15

Cisco 880 Series Data Routers

The Cisco 880 series data routers provide integrated VPN, embedded Wi-Fi CERTIFIED™,

802.11b/g/n-compliant wireless AP, 3G, and backup capabilities. the features available on Cisco 880 series data routers. Some of the features shown may not be available on your router.

Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, VDSL/ADSL over ISDN, VDSL/ADSL over POTS, or 10/100

Routers data sheet for the WAN interface that is supported on your router.

Figure 1-6 shows the front panel details of the Cisco 880 wireless data router. The USB port and the 3G

card slot are located on the front panel.

Figure 1-6 through Figure 1-9 show

FE. See the Cisco 880 Series Integrated Services

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-6

OL-16215-10

Page 23

Chapter 1 Product Overview

231950

1 2 3

254090

1 3 4 5 7 8 962

Figure 1-6 Front Panel of the Cisco 880 Series Wireless Data Router

1 LEDs 3 USB port 2 3G express card slot—Supports third-party1

1. See the Cisco 880 Series Integrated Services Routers data sheet for supported vendors.

Cisco 880 Series ISRs

3G card (Cisco 880G models only)

Figure 1-7 shows the back panel details of the Cisco 886VA data router.

Figure 1-7 Back Panel of the Cisco 886VA Router

1 Data BRI1 0 6 Reset button 2 Primary WAN port—VDSL/ADSL over

7 Power connector

ISDN

3 4-port 10/100 Ethernet switch

8 Earth ground connection 4 Serial port—console or auxiliary 9 Kensington security slot 5 PoE power connector—optional

1. BRI = Basic rate interface.

2. Ports 0 and 1 provide PoE with the optional PoE module installed.

Caution The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN

port may occur if a non-RJ-45 connector is inserted.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

1-7

Page 24

Cisco 880 Series ISRs

254139

2 3 4 6 7 851

231951

1 4 5 6 8 9 1072 3

Chapter 1 Product Overview

Figure 1-8 shows the back panel details of the Cisco 887VA and 886VA-M data router.

Figure 1-8 Back Panel of the Cisco 887VA and 887VA-M Router

1 Primary WAN port—VDSL/ADSL over

2 4-port 10/100 Ethernet switch

POTS

5 Reset button

6 Power connector 3 Serial port—console or auxiliary 7 Earth ground connection 4 PoE power connector—optional 8 Kensington security slot

1. 887VA-M has Annex M support.

2. Ports 0 and 1 provide PoE with the optional PoE module installed.

Caution For the Cisco 887VA, the primary WAN port is designed for an RJ-45 connector only. Damage

to the primary WAN port may occur if a non-RJ-45 connector is inserted.

Figure 1-9 shows the back panel details of the Cisco 888W data router. Nonwireless routers do not have

antennas on the back panel. However, the feature locations are similar across all Cisco 880 series data routers.

Figure 1-9 Back Panel of the Cisco 888W Data Router

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-8

OL-16215-10

Page 25

Chapter 1 Product Overview

Cisco 880 Series ISRs

1 ISDN port—not available on 3G models 6 PoE power connector for optional PoE

2 Primary WAN port2—G.SHDSL,

VDSLoPOTS, ADSLoPOTS, ADSLoISDN, or 10/100 FE

3 Antenna—captive omnidirectional dipole

WLAN antenna (wireless models only)

4 4-port 10/100 Ethernet switch 9 Earth ground connection 5 Serial port—console or auxiliary 10 Kensington security slot

1. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and install it to enable the PoE function.

2. Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, or 10/100 FE. The VDSLoPOTS port is in the same location as the G.SHDSL port. The 10/100 FE WAN port is located at the bottom left corner. See for the location of the 10/100 FE WAN port.

Cisco 880 Series Voice and Data Routers

The Cisco 880 series voice and data routers provide both voice and data ports. The voice ports managed voice services that interface with Foreign Exchange Station (FXS), Foreign Exchange Office (FXO), or BRI connections.

module

7 Reset button

8 Power connector

Figure 1-2

Cisco 881 SRST and Cisco 888 SRST

Figure 1-10, Figure 1-11, and Figure 1-12 show the features available on the Cisco 881 SRST and

Cisco 888 SRST routers. The features available vary, depending on the router model. Some features may not be available on your router.

Depending on the router model, the primary WAN port can be either G.SHDSL or 10/100 FE. See the

Cisco 880 Series Integrated Services Routers data sheet for the WAN interface and voice ports that are

supported on your router.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

1-9

Page 26

Cisco 880 Series ISRs

270495

1 2

Chapter 1 Product Overview

Figure 1-10 shows the front panel details of the Cisco 881 SRST and Cisco 888 SRST wireless voice

router.

Figure 1-10 Front Panel of the Cisco 881 SRST and Cisco 888 SRST Wireless Voice Router

1 LEDs 2 USB port

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-10

OL-16215-10

Page 27

Chapter 1 Product Overview

241904

31 4 7 98 1022 56

Figure 1-11 shows the back panel details of the Cisco 881SRST-W voice router.

Figure 1-11 Back Panel of the Cisco C881SRST-W Voice Router

Cisco 880 Series ISRs

1 Primary WAN port1—10/100 FE

6 Antenna—captive wireless omnidirectional

dipole WLAN antenna (wireless models only)

2 Voice ports—four FXS2/DID3 ports, one

7 Reset button

FXO4 port with TBP5 power failover

3 4-port 10/100 Ethernet switch

8 Power connector 4 Serial port—console or auxiliary 9 Earth ground connection 5 PoE power connector for optional PoE

module

1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.

2. FXS = Foreign Exchange Station.

3. DID = Direct Inward Dialing.

4. FXO = Foreign Exchange Office.

5. TBP = trunk bypass.

6. Ports 0 and 1 provide PoE with the optional PoE module installed.

7. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected to ethernet ports 0 and 1. If this feature was not configured with the factory order, SKU 800-IL-PM-2, you must order and install it to enable the PoE function. The PoE power supply, SKU 800-ILPM-4, is also required.

10 Kensington security slot

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

1-11

Page 28

Cisco 880 Series ISRs

241905

32 2 4 7 9 1086 51

Chapter 1 Product Overview

Figure 1-12 shows the back panel details of the Cisco 888SRST-W voice router.

Figure 1-12 Back Panel of the Cisco C888SRST-W Voice Router

1 Primary WAN port1—G.SHDSL

6 Antenna—captive wireless omnidirectional

dipole WLAN antenna (wireless models only)

2 Voice ports—four FXS/DIDports and one

7 Reset button

voice BRI port

3 4-port 10/100 Ethernet switch

8 Power connector 4 Serial port—console or auxiliary 9 Earth ground connection 5 PoE power connector for optional PoE

module

1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.

2. Ports 0 and 1 provide PoE with the optional PoE module installed.

3. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected to ethernet ports 0 and 1. If this feature was not configured with the factory order, SKU 800-IL-PM-2, you must order and install it to enable the PoE function. The PoE power supply, SKU 800-ILPM-4, is also required.

Caution The primary WAN port on all 888E models is designed for an RJ-45 connector only. Damage

10 Kensington security slot

to the primary WAN port may occur if a non-RJ-45 connector is inserted.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-12

OL-16215-10

Page 29

Chapter 1 Product Overview

Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W

Figure 1-13, Figure 1-14, and Figure 1-15 show the features available on the Cisco 881-V and

Cisco 887VA-V routers. The features available vary, depending on the router model. Some features may not be available on your router.

The Cisco 881-V and Cisco 887VA-V voice and data series gives you the flexibility to use either FXS or BRI voice ports. However, the number of concurrent calls that can be supported by the router is limited by the codec complexity setting on the router. supported when the codec complexity command is configured for Flexible, Medium or High complexity.

Note Configuring the codec complexity setting to support secure calls uses DSP resources, but does not affect

the maximum number of supported calls.

Ta b l e 1-3 Maximum Number of Supported Calls

Flexible Complexity Medium Complexity High Complexity

C881-V 9 8 6

C887VA-V 8 8 6

C887VA-V-W 8 8 6

Cisco 880 Series ISRs

Tabl e 1-3 lists the maximum number of calls that is

Figure 1-13 shows the front panel details of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W.

Figure 1-13 Front Panel of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W Routers

1 2

1 LEDs 2 USB port

246861

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

1-13

Page 30

Cisco 880 Series ISRs

246864

overPOTS

VDSL/ADSL

C887VA-W VOICE

1 4 5 6 8 9 107

246866

C881 VO ICE

1 4 5 6 8 9 10732

Chapter 1 Product Overview

Figure 1-14 shows the back panel for the Cisco 887VA-V-W router. The Cisco 887VA-V (non-wireless)

router does not have the antennas on the back panel.

Figure 1-14 Back Panel of the Cisco 887 VA-V Router

1 Data BRI 7 Reset Button 2 Voice BRI 8 Power connector 3 Voice ports—four FXS/DID ports 9 Earth ground connection 4 Fast Ethernet LAN—four ports 10 Kensington security slot 5 Console Port 11 Primary WAN port—VDSL/ADSL over

POTS

6 PoE power connector (optional)

Figure 1-15 shows the back panel for the Cisco 881-V router.

Figure 1-15 Back Panel of the Cisco 881-V Router

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-14

OL-16215-10

Page 31

Chapter 1 Product Overview

284983

PPP

WLAN

POE

LINK 2.4GHz 5GHz

Cisco 800 Series

FE LAN

VPN

0123

xDSL

CD DATA

1 Fast Ethernet WAN port 6 PoE power connector (optional) 2 Voice BRI ports 7 Reset button 3 Voice ports—four FXS/DID ports and one

8 Power connector

FXO port.

4 Fast Ethernet LAN—four ports 9 Earth ground connection 5 Console Port 10 Kensington security slot

Cisco 880 Series with Embedded WLAN Antennas

Some Cisco 880W, 880WD, and 880-WD ISRs have three embedded WLAN antennas.

These ISRs are fixed-platform routers that:

• Provide integrated VPN, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP, and

backup capabilities.

• Use single-band (2.4 GHz) WLAN cards or dual-band (2.4 GHz and 5 GHz) WLAN cards.

Cisco 880 Series ISRs

Cisco 887VA-WD

• Require a single external power supply: a 30-W power supply for non-POE-enabled routers or a

60-W power supply for POE-enabled routers.

• Have a fixed 512 MB of system memory.

For information on configuring the Cisco 880 series ISRs, see Cisco 880 Series Integrated Services

Router Software Configuration Guide.

Figure 1-16 shows the front panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs. The

front panel has LEDs only. All the ports are in the back panel.

Figure 1-16 Front Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs

OL-16215-10

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-15

Page 32

Cisco 880 Series ISRs

284988

Cisco 887VA-WD

AUX

CONSOLE

FE LAN

POE OPTION REQUIRES 5A

POWER

ADAPTOR

3210

RESET

12VDC 5A

overPOTS

1 2 3 4 5 6 7

284988

Cisco 887VA-WD

AUX

CONSOLE

FE LAN

POE OPTION REQUIRES 5A

POWER

ADAPTOR

3210

RESET

12VDC 5A

overPOTS

1 2 3 4 5 6 7

284982

PPP

FE4

WAN

WLAN

POE

LINK 2.4GHz 5GHz

Cisco 800 Series

FE LAN

VPN

0123

Chapter 1 Product Overview

Figure 1-17 shows the back panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs.

Figure 1-17 Back Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs

1 USB port 6 Power connector 2 4-port 10/100 Ethernet switch 7 Kensington security slot 3 Serial port—console or auxiliary 8 Power switch 4 Note No separate PoE power supply is

required for routers with embedded WLAN antennas. For information on system power supply requirements when PoE is enabled, see the

“Power over Ethernet Module” section on page 1-38.

5 Reset button

9 VDSL/ADSL port

C881WD

Figure 1-18 shows the front panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs. The front

panel has LEDs only. All the ports are in the back panel.

Figure 1-18 Front Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-16

OL-16215-10

Page 33

Chapter 1 Product Overview

284987

Cisco 881WD

AUX

CONSOLE

FE LAN

POE OPTION

REQUIRES 5A

POWER

ADAPTOR

3210

RESET

12VDC 5A

FE WAN

21 3 4 5 6 7 8

Figure 1-19 shows the back panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs.

Figure 1-19 Back Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs

1 Primary WAN port—10/100 FE 6 Reset button 2 USB port 7 Power connector 3 4-port 10/100 Ethernet switch 8 Kensington security slot 4 Serial port—console or auxiliary 9 Power switch 5 Note No separate PoE power supply is

required for routers with embedded WLAN antennas. For information on system power supply requirements when PoE is enabled, see the

over Ethernet Module” section on page 1-38.

“Power

Cisco 890 Series ISRs

Cisco 891, Cisco 892, and Cisco 892F

The Cisco 891, Cisco 892, and Cisco 892F ISRs have the following features:

• Integrated 8-port 10/100 Ethernet switch for connecting to the LAN

• 10/100 FE and 10/100/1000 Gigabit Ethernet (GE) port for connecting to the WAN

• Separate console and auxiliary ports

• Optional embedded Wi-Fi CERTIFIED™ dual radio 802.11a/b/g/n-compliant wireless AP

• Optional 4-port PoE

Note The Cisco 890 series ISRs can include an optional PoE module that provides power to

• Security feature card (SFC) socket

OL-16215-10

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

802.3af-compliant devices connected to ethernet ports 0 through 3. If this feature was not configured with the factory order, you must order and install it to enable the PoE function.

1-17

Page 34

Cisco 890 Series ISRs

272367

1 2

Chapter 1 Product Overview

• DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB

system memory in Cisco 891 and 892 series ISRs, and a total of 1 GB system memory in Cisco

892F series ISRs

• Three reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel for

non-captive dual-band WLAN antenna (wireless models only)

• Support for the AIM2-CUE-K9 and AIM2-APPRE-104-K9

• GE small-form-factor pluggable (SFP) port (Cisco 892F series ISRs only)

The following feature is located on the front panel:

• Two USB 2.0 ports

Figure 1-20 shows the front panel details of the Cisco 890 wireless router.

Figure 1-20 Front Panel of the Cisco 890 Series Wireless ISR

1-18

1 LEDs 2 USB ports

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Page 35

Chapter 1 Product Overview

272369

4 5 6 8 9 10 1172 3

Figure 1-21 shows the back panel details of the Cisco 892-W router. Nonwireless routers do not have

RP-TNC antennas or connectors on the back panel. Some of the features that are shown may not be available on your router. However, the feature locations are similar across all Cisco

Figure 1-21 Back Panel of the Cisco 892-W Router

Cisco 890 Series ISRs

890 series routers.

1 Antenna—dipole swivel antenna attached to

RP-TNC connectors (wireless models only)

2 Backup—Data BRI2 or V.923 port

7 PoE power connector for optional PoE

module

8 Reset button 3 Primary WAN port—FE and GE 9 Power connector 4 Auxiliary port 10 Earth ground connection 5 Console port 11 Kensington security slot 6 8-port 10/100 Ethernet switch

1. The Cisco 890 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected to ethernet ports 0 through 3. If this feature was not configured with the factory order you must order and install it to enable the PoE function.

2. The Data BRI port is available only on the Cisco 892 router models.

3. The V.92 port (not shown) is available only on the Cisco 891 router models and is located between the console port and the Ethernet switch.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

1-19

Page 36

Cisco 890 Series ISRs

278179

Cisco 892F-W

SFP

Chapter 1 Product Overview

Figure 1-22 shows the location of the SFP port in a Cisco 892F-W router.

Figure 1-22 SFP Port Location in a Cisco 892F-W Router

1 SFP port 2 SFP LEDs

Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA

The Cisco 892FSP, 896VA, 897VA (897VA, 897VAM, 897VAW, 897VAMW), and 898EA routers have the following features:

• Integrated 8-port 10/100/1000 Gigabit Ethernet(GE) switch for connecting to the LAN

• Two 10/100/1000 GE ports for the Cisco 892FSP

• One 10/100/1000 GE port for the Cisco 896VA, 897VA, and the Cisco 898EA. Either the SFP socket

or the 10/100/1000 GE port can be active at a given time, but not both.

• Single console and auxiliary ports for configuration and management

• 512 MB of on-board memory (upgrade option to 1 GB)

• 256 MB flash memory for the Cisco 896VA, 897VA, and Cisco 898EA

• One USB 2.0 port

• Optional internal adapter for inline PoE on 4 switch ports for IP phones or external wireless access

points for Cisco 896VA, 897VA, and 898EA models only. No PoE support on Cisco 892FSP.

Note The Cisco 892FSP does not support AIM2-CUE-K9 and AIM2-APPRE-104-K9 because it does not have

an SFC socket.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-20

OL-16215-10

Page 37

Chapter 1 Product Overview

GE WA N

SFP

12VD C 2.5A

CONSOLE

AUX

RESE T

Cisco 892FSP

284781

2 3 4 5 6 8 9 1071

Figure 1-23 shows the back panel of the Cisco 892FSP router.

Figure 1-23 Back Panel of the Cisco 892FSP Router

1 GE WAN interface 6 Power connector 2 SFP port 7 On/Off switch 3 USB port 8 Reset button 4 8-port Gigabit Ethernet switch 9 Earth ground connection 5 Console / Auxiliary port 10 Kensington security slot

Cisco 890 Series ISRs

Figure 1-24 shows the front panel of the Cisco 892FSP router.

Figure 1-24 Front Panel of the Cisco 892FSP Router

1 LEDs

284782

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

1-21

Page 38

Cisco 890 Series ISRs

344765

Figure 1-25 shows the back panel of the Cisco 896VA router.

Figure 1-25 Back Panel of the Cisco 896VA Router

VDSL/ADSL

overISDN

GE WAN

ISDN

7 6 GELAN 5 4

Chapter 1 Product Overview

Cisco 896VA

CONSOLE

RESET

6 7

54VDC 1.2A 12VDC 2.5A

3 2 POE 1 0

1 2 3 4 5 8 9 10 11

1 ISDN 7 Power connector 2 GE WAN interface 8 On/Off switch 3 SFP port 9 Reset button 4 USB port 10 Earth ground connection 5 8-port Gigabit Ethernet switch

11 Kensington security slot

6 Console / Auxiliary port 12 VDSL / ADSL over ISDN

1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with the factory order, you must order and install it to enable the PoE function.

Figure 1-26 shows the front panel of the Cisco 896VA and the Cisco 897VA router.

Figure 1-26 Front Panel of the Cisco 896VA and Cisco 897VA Router

344766

1 LEDs

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-22

OL-16215-10

Page 39

Chapter 1 Product Overview

7 6 GELAN 5 4

3 2 POE 1 0

ISDN

GE WAN

54VDC 1.2A 12VDC 2.5A

VDSL/ADSL

overPOTS

CONSOLE

RESET

Cisco 897VA

344767

1 2 3 4 5 8 9 10 11

6 7

7 6 GELAN 5 4

3 2 POE 1 0

GE WAN

54VDC 1.2A 12VDC 2.5A

VDSL/ADSL

overPOTS

CONSOLE

RESET

344769

1 2 3 4 7 8 9 10

5 6

Figure 1-27 shows the back panel of the Cisco 897VA router.

Figure 1-27 Back Panel of the Cisco 897VA Router

1 ISDN 7 Power connector 2 GE WAN interface 8 On/Off switch 3 SFP port 9 Reset button 4 USB port 10 Earth ground connection 5 8-port Gigabit Ethernet switch 6 Console / Auxiliary port 12 VDSL / ADSL over POTS

1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with

the factory order, you must order and install it to enable the PoE function.

11 Kensington security slot

Cisco 890 Series ISRs

Figure 1-28 shows the back panel of the Cisco 897VAM router.

Figure 1-28 Back Panel of the Cisco 897VAM Router

1 GE WAN interface 7 On/Off switch 2 SFP port 8 Reset button 3 USB port 9 Earth ground connection

OL-16215-10

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-23

Page 40

Cisco 890 Series ISRs

7 6 GELAN 5 4

3 2 POE 1 0

GE WAN

54VDC 1.2A 12VDC 2.5A

VDSL/ADSL

overPOTS

CONSOLE

RESET

344771

1 2 3 4 7 8 9 10

5 6

Chapter 1 Product Overview

4 8-port Gigabit Ethernet switch

10 Kensington security slot 5 Console / Auxiliary port 11 VDSL / ADSL over POTS 6 Power connector

Figure 1-29 shows the front panel of the Cisco 897VAM router.

Figure 1-29 Front Panel of the Cisco 897VAM Router

1 LEDs

344768

Figure 1-30 shows the back panel of the Cisco 897VAW router.

Figure 1-30 Back Panel of the Cisco 897VAW Router

1 GE WAN interface 7 On/Off switch 2 SFP port 8 Reset button 3 USB port 9 Earth ground connection 4 8-port Gigabit Ethernet switch

10 Kensington security slot 5 Console / Auxiliary port 11 VDSL / ADSL over POTS 6 Power connector

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-24

OL-16215-10

Page 41

Chapter 1 Product Overview

344770

7 6 GELAN 5 4

3 2 POE 1 0

GE WAN

54VDC 1.2A 12VDC 2.5A

VDSL/ADSL

overPOTS

CONSOLE

RESET

344772

1 2 3 4 7 8 9 10

5 6

Figure 1-31 shows the front panel of the Cisco 897VAW and the Cisco 897VAMW router.

Figure 1-31 Front Panel of the Cisco 897VAW and the Cisco 897VAMW Router

1 LEDs

Figure 1-32 shows the back panel of the Cisco 897VAMW router.

Cisco 890 Series ISRs

Figure 1-32 Back Panel of the Cisco 897VAMW Router

1 GE WAN interface 7 On/Off switch 2 SFP port 8 Reset button 3 USB port 9 Earth ground connection 4 8-port Gigabit Ethernet switch

10 Kensington security slot 5 Console / Auxiliary port 11 VDSL / ADSL over POTS 6 Power connector

OL-16215-10

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-25

Page 42

Cisco 890 Series ISRs

7 6 GELAN 5 4

3 2 POE 1 0

GE WAN

SFP

54VDC 1.2A 12VDC 2.5A

SHDSL

RJ45 ONLY

CONSOLE

RESET

Cisco 898EA

AUX

344774

1 2 3 4 7 8 9 10

5 6

344773

Chapter 1 Product Overview

Figure 1-33 shows the back panel of the Cisco 898EA router.

Figure 1-33 Back Panel of the Cisco 898EA Router

1 GE WAN interface 7 On/Off switch 2 SFP port 8 Reset button 3 USB port 9 Earth ground connection 4 8-port Gigabit Ethernet switch 5 Console / Auxiliary port 11 SHDSL (RJ45 Only) 6 Power connector

10 Kensington security slot

1-26

Caution The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN

port may occur if a non-RJ-45 connector is inserted.

Figure 1-34 shows the front panel of the Cisco 898EA router.

Figure 1-34 Front Panel of the Cisco 898EA Router

1 LEDs

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Page 43

Chapter 1 Product Overview

Hardware Features

This section provides an overview of the following hardware features for the Cisco 860 series, 880 series, and 890 series ISRs. A feature summary is available at the end of this section.

• Kensington Lock

• Reset Button

• LEDs

• Memory

• USB Port

• Fan

• Power over Ethernet Module

• 3G Cellular Data WAN Connectivity

• Wireless LAN Connectivity

• Small Form-Factor Pluggable Port

• Feature Summary

Hardware Features

Kensington Lock

A Kensington security slot is located on the router back panel. To secure the router to a desktop or other surface, use the Kensington lockdown equipment.

Reset Button

The Reset button is used to restore the router to the factory default configurationor to load a custom configuration file.

There are two different ways to do this:

1. by pressing the Reset button within 5 seconds of powering up the router; or

2. by pressing the Reset button for 5 seconds while running IOS.

Note If you execute a CLI reboot command while the embedded wireless AP is running Cisco Unified IOS

software, the router reboots, but the AP continues running. Clients with Cisco Unified IOS software are controlled by a wireless LAN controller (WLC) and can be reset only by the controller.

Cisco 860VAE Routers—Custom Configuration File

On Cisco 860VAE routers, the reset button can be used to load a custom configuration file without having to use the CLI. The configuration file can be located on an external USB flash drive or on the router's compact flash.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

1-27

Page 44

Hardware Features

Chapter 1 Product Overview

The custom configuration file must be named one of the following:

• customer-config

• SN-customer-config

where “SN” is the unique hardware serial number.

When the system attempts to load a custom configuration file, configuration files on a USB flash drive have priority over configuration files on the router's flash drive and the “SN-customer-config” file name has priority over the “customer-config” file name. The priority for loading a configuration file is as follows:

1. USB flash0: SN-customer-config

2. USB flash0: customer-config

3. Router flash: SN-customer-config

4. Router flash: customer-config

If the router does not find a valid custom configuration file, the system aborts the process.

To reset the router to the factory default configuration, follow these steps:

Step 1 Verify that IOS is running correctly by checking that the system status LED is on. Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within

seconds.

The router reloads itself after the startup configuration has been replaced with the new customer configuration.

Custom Configuration File for Cisco 892FSP, 896VA, 897VA, and Cisco 898EA

For the first method, the configuration file can be located on the router's compact flash or on the router's nvram. The custom configuration file must use cfg as the filename extension.

When the system attempts to load a custom configuration file, configuration files on nvram have priority over configuration files on the router's compact flash.

The priority for loading a configuration file is as follows:

1. nvram: *.cfg

2. Router flash: *.cfg

If the router does not find a valid custom configuration file, the system aborts the process.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-28

OL-16215-10

Page 45

Chapter 1 Product Overview

To reset the router to the factory default configuration or to load a custom configuration file, follow these steps:

Step 1 Turn the power on. Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within

seconds.

The router reloads itself after the startup configuration has been replaced with the new customer configuration.

For the second method, the configuration file can be located on an external USB flash drive or on the router's compact flash.

The custom configuration file must be named one of the following:

• customer-config

• customer-config.SN ?

When the system attempts to load a custom configuration file, configuration files on a USB flash drive have priority over configuration files on the router's flash drive and the "customer-config.SN" file name has priority over the customer-config file name.

Hardware Features

where "SN" is the unique hardware serial number.

The priority for loading a configuration file is as follows:

1. usbflash0:customer-config.SN

2. usbflash0:customer-config

3. Router flash:customer-config.SN

4. Router flash:customer-config

If the router does not find a valid custom configuration file, the system aborts the process.

To reset the router to the factory default configuration or to load a custom configuration file, follow these steps:

5 seconds.

The router reloads itself after the startup configuration has been replaced with the new customer configuration.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

1-29

Page 46

Chapter 1 Product Overview

Hardware Features

LEDs

The LEDs are located on the front panel of the router.

• Table 1-4 describes the LEDs for the Cisco 860 series, 880 series, and 890 series ISRs.

• Table 1-5 lists the LED descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and

Cisco 867VAE-K9 ISRs.

• Table 1-6 lists the LED description for the Cisco 892FSP ISR, 896VA, 897VA, and 898EA.

Ta b l e 1-4 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs

LED Color Description 860 Series 880 Series 890 Series

Power OK Green On—DC power is being supplied to the router and the

Cisco

IOS software is running.

Blinking—Bootup is in process, or the router is in Rommon monitor mode.

Off—Power is not supplied to the router.

Link Status FE0 Green On—Ethernet port is connected.

Link Status FE1

Link Status FE2

Link Status FE3

Blinking—Data is either being received or being transmitted.

Off—Ethernet port is not connected.

Link Status FE4 Green On—Ethernet port is connected.

Link Status FE5

Link Status FE6

Link Status FE7

FE WAN Port Link Status

Green On—Port is connected.

Blinking—Data is either being received or being transmitted.

Off—Ethernet port is not connected.

Blinking—Data is either being received or being transmitted.

Off—Port is not connected.

GE WAN Port Link Status

Green On—Port is connected.

Blinking—Data is either being received or being transmitted.

Off—Port is not connected.

WLAN (2.4

GHz)

Green On—Radio is connected, SSID1 is configured, and client

is associated, but no data is being received or being transmitted.

Slow blinking—Radio is connected, SSID is configured, and beacons are being transmitted.

All models All models All models

— — All models

861 models

881 models

All models

— — All models

Wireless models

Fast blinking—Data is either being received or being transmitted.

Off—Radio is shut down, and no SSID is configured.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-30

OL-16215-10

Page 47

Chapter 1 Product Overview

Hardware Features

Table 1-4 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

LED Color Description 860 Series 880 Series 890 Series

WLAN (5 GHz) Green On—Radio is connected, SSID is configured, and client is

associated, but no data is being received or being transmitted.

Slow blinking—Radio is connected, SSID is configured, and beacons are being transmitted.

Fast blinking—Data is either being received or being transmitted.

Off—Radio is shut down, and no SSID is configured.

WLAN LINK (Autonomous Mode)

Green On—Wireless link is up.

Blinking—Ethernet link is up, and data is either being received or being transmitted.

Off—Wireless link is down.

WLAN LINK (Unified Mode)

Green On—Ethernet link is up, and wireless access point (AP) is

communicating with LWAPP2 controller.

Blinking—Ethernet link is up, but wireless AP is not communicating with LWAPP controller.

— Wireless

models

Wireless models

— Wireless

models

Wireless models

Off—Ethernet link is down.

PoE Green On—PoE is connected and powered.

Off—PoE is not installed.

— Models

with PoE

Models with PoE

Amber On—Fault with the PoE.

VPN Green On—VPN is connected. — All models All models

PPP

xDSL4 CD Green On—The xDSL interface is connected to the DSLAM5.

xDSL Data Green Blinking—The xDSL interface is either receiving or

xDSL ATM Green On—The router is operating in ATM6 mode.

Green On—At least one PPP session is established. — All models All models

Blinking—Training to the line.

Off—Indicates that a connection has not been established or the port is shut down.

transmitting data.

Off—No data is being transmitted or being received.

— 887,

887VA, 887VA-M8 888 models

— 887,

887VA, 887VA-M8 88 models

896VA, 897VA, 898EA

— 888E —

Off—Not operating in ATM mode.

xDSL EFM Green Blink—The router is operating in EFM7 mode.

— — 898EA

Off—Not operating in EFM mode.

Data BRI LINK Green On—ISDN D channel is connected. — 887, 888

models

Data BRI B1 Green Blinking—B1 channel is either receiving or sending data,

or data is passing through ISDN channel 1.

— 887, 888

models

892 models

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

1-31

Page 48

Chapter 1 Product Overview

Hardware Features

Table 1-4 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

LED Color Description 860 Series 880 Series 890 Series

Data BRI B2 Green Blinking—B2 channel is receiving or sending data, or

data is passing through ISDN channel 2.

3G8 WWAN

Green On—Service is established.

Slow Blinking—Searching for service.

Fast Blinking—Data is either being received or being transmitted.

3G RSSI

Green Off—Low signal strength (lower than -100 dBm).

On—High RSSI (-69 dBm or higher).

Slow Blinking—Low or medium RSSI (-99 to -90 dBm).

Fast Blinking—Medium RSSI (-89 to -70 dBm).

Amber On—No service. — 3G models —

3G GSM

Green On—Service is established.

Off—No service.

3G CDMA

Green On—Service is established.

— 887, 887V,

888

892 models

models

— 3G models —

Off—No service.

FXO Voice Green On—FXO port is connected.

— 881

—

Blinking—FXO port is either receiving or transmitting data.

BRI Voice LNK Green On—BRI interface is connected. — — —

BRI Voice B1 Green On—BRI B1 channel is connected.

— — —

Blinking—BRI B1 channel is either receiving or transmitting data.

BRI Voice B2 Green On—BRI B2 channel is connected.

— — —

Blinking—BRI B2 channel is either receiving or transmitting data.

FXS/DID Voice Green On—FXS/DID port is connected.

Blinking—FXS/DID port is either receiving or

— SRST

models

—

transmitting data.

V.92 Modem Green On—Modem is connected.

Blinking—V.92 port is either receiving or transmitting

— — 891

models

data.

SFP14 EN Off Not present. — — 892F

Green Present and enabled. — —

models

Amber Present with failure. — —

SFP S Green Blinking—Blinking frequency indicates port speed. — — 892F

models

1. SSID = service set identifier.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-32

OL-16215-10

Page 49

Chapter 1 Product Overview

Hardware Features

2. LWAPP = Lightweight Access Point Protocol.

3. PPP = Point-to-Point Protocol.

4. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital subscriber line).

5. DSLAM = digital subscriber line access multiplexer.

6. ATM = Asynchronous Transfer Mode.

7. EFM = Ethernet in the First Mile.

8. 3G = Third-Generation.

9. WWAN = wireless WAN.

10. RSSI = Received Signal Strength Indicator.

11. GSM = Global System for Mobile Communication.

12. CDMA = code division multiple access.

13. SRST = Survivable Remote Site Telephony.

14. SFP = small-form-factor pluggable.

Table 1-5 describes the LEDs for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco

867VAE-K9 ISRs.

Ta b l e 1-5 LED Descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs

LED Activity Description

Power/System Power/System LED: Solid

GE_MODE LED: Off DSL_LINK LED: Off

Power is on and system running in the Rommon mode.

Note During the early booting stage, both Power/System, GE_MODE and

DSL_LINK LED will be turned on temporarily for the power on test. DSL_LINK and GE_MODE LED will be turned off later after booting into Rommon.

Power/System LED: Solid

IOS functioning in GE WAN mode. GE_MODE LED: Solid DSL_LINK LED: Off

Power/System LED: Solid GE_MODE LED: Off DSL_LINK LED: Solid or flashing

IOS functioning in DSL_WAN mode.

Note In IOS DSL_WAN mode, DSL_LINK LED will be solid after DSL

training complete or flashing during training.

xDSL1 ACT Green On—DSL interface is up.

Blinking—DSL WAN activity (traffic in either direction).

Faster blinking—Heavier traffic

Off—Device is powered off or the DSL WAN interface is down.

xDSL Link Green On—DSL WAN Mode is selected and DSL training complete.

Blinking—DSL WAN Mode is selected but incomplete DSL Link Up state,

such as in-training, or controller “OFF,” or no cable attached to DSL connector.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Off—Device is powered off or GE WAN mode is selected.

1-33

Page 50

Chapter 1 Product Overview

Hardware Features

Table 1-5 LED Descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs

LED Activity Description

GE ACT Green On—GE WAN interface is up.

Blinking—GE WAN activity (traffic in either direction).

Off—Device is powered off or GE WAN interface is down.

GE Mode Green On—GE WAN Mode is selected.

Off—Device is powered off or DSL WAN mode is selected.

1. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital subscriber line).

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-34

OL-16215-10

Page 51

Chapter 1 Product Overview

Table 1-6 describes the LEDs for the Cisco 892FSP.

Ta b l e 1-6 LED desciption for Cisco 892FSP ISR, 896VA, 897VA, and 898EA Routers

LED Color Activity Description

PWR_OK Green Power Status Off—No power.

GE0 Green/Amber Link Status Green On—Ethernet port is connected.

GE1

GE2

GE3

GE4

GE5 Green Link Status On—Ethernet port is connected.

GE6

GE7

GE WAN ports Green Link Status On—Port is connected.

SFP WAN ports

VPN_OK Green — Off—No tunnel.

Hardware Features

Steady on—Normal operation.

Blink—Boot up phase or in ROM Monitor mode.

Amber On—Fault with PoE. There is a fault with the inline power supply.

Green/Amber Blinking—Data is either being received or being transmitted.

Green/Amber Off—Ethernet port is not connected.

Blinking—Data is either being received or being transmitted.

Off—Ethernet port is not connected.

Blinking—Data is either being received or being transmitted.

Off—No link.

Green Link Status On—Port is connected.

Blinking—Data is either being received or being transmitted.

Off—No link.

PPP_OK Green — Off—No PPP session.

Shared LEDs on the Cisco 881-V and Cisco 887VA-V Voice and Data Routers

On the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W routers, the BRI1, BRI2 and the FXS ports share LED indicators. The following ports share an LED indicator:

• BRI 1B1 channel and FXS 3

• BRI 1B2 channel and FSX 4

• BRI 2B1 channel and FXS 5

• BRI 2 B2 channel and FXS 6

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Steady on—At least one tunnel is up.

Steady on—At least one PPP established.

1-35

Page 52

Hardware Features

Chapter 1 Product Overview

Because the LED indicators are shared, the LED illuminates (green) when either port is active. For example, the LED indicator labeled BRI 1 B1 illuminates when either the BRI1 B1 channel is active or when the FXS port is active. You can determine the activity status on each interface by using the following commands.

• For activity status on the FXS ports, use the show port summary command.

• For activity status on the BRI ISDN port, use the show isdn status command.

Figure 1-35 shows a close-up view of the LED indicators.

Figure 1-35 Close-up of the BRI and FXS LED Indicators

Memory

The Cisco 860 series, 880 series, and 890 series routers contain flash memory and main memory.

Flash Memory

The Cisco 860 series, 880 series, and 890 series ISRs use non-upgradable flash memory storage. The onboard flash memory contains the Cisco

IOS software image, the boot flash contains the ROMMON

boot code, and a separate non-volatile flash contains the cookie configuration.

Table 1-7 describes the default flash memory storage.

Ta b l e 1-7 Flash Memory Storage

Models Flash Memory Storage

Cisco 860 series and 880 series routers 128 MB

Cisco 880 series voice routers and Cisco 890 series routers 256 MB

Cisco 880 series routers with embedded WLAN antennas 256 MB

Cisco 860VAE routers 8 MB boot flash, 128 MB for IOS

Cisco 860VAE-K9 64 MB boot flash and IOS

300149

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-36

OL-16215-10

Page 53

Chapter 1 Product Overview

Note Flash memory is not upgradable. An external USB flash memory module may be used if additional flash

memory is needed.

Main Memory

Table 1-8 describes the main onboard memory storage for different router models.

Ta b l e 1-8 Main Onboard Memory Storage

Models Onboard Memory Storage Expandability

Cisco 860 series routers 256 MB Not expandable.

Cisco 860VAE series routers 256 MB Not expandable.

Cisco 880 series routers 256 MB

Cisco 880 series routers with embedded WLAN antennas

Cisco 892FSP, 896VA, 897VA, 898EA routers

A memory expansion slot accommodates

(expandable to 768 MB)

512 MB Not expandable.

512 MB Expandable to 1 GB.

a PC2-4200, 256-MB or 512-MB double data rate 2 (DDR2) SODIMM, for a maximum of 768 MB.

Hardware Features

USB Port

Fan

Table 1-9 describes the USB ports for different router models.

Ta b l e 1-9 USB Ports

Models USB

Cisco 860 series (non-VAE) No USB ports.

Cisco 860VAE series One USB 1.1-compliant port located on the back panel. The USB

port does not support eToken.

Cisco 880 series One USB 1.1-compliant port located on the front panel. The USB

port provides connection for USB devices such as security tokens and flash memory.

Cisco 890 series

Cisco 892FSP, Cisco 896VA, Cisco897VA, Cisco

1. Except for Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA.

Two USB 2.0-compliant ports located on the front panel.

One USB 2.0-compliant port located on the back panel.

898EA

Some router models do not have a fan, while other models have either one or two fans.

The fans spin at full speed, as a diagnostic aid, immediately after the router is powered up. After the router has booted, the fans spin as fast as necessary to minimize fan noise while maintaining a safe internal operating temperature.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

1-37

Page 54

Hardware Features

The following models have no fan:

• Cisco 892FSP

• Cisco 896VA

• Cisco 897VA

• Cisco 898EA

Power Supply

The Cisco 892FSP has a single +12V power supply input. The Cisco 892FSP power connector is different from the barrel-type connector on other 890 series models. The AC adapter cable connector has four pins and a built-in locking mechanism.

The Cisco 896VA, 897VA, and Cisco 898EA use PoE (12 VDC 43 W, - 5 4 VDC 80 W) and non-PoE (12

VDC 60 W) power supplies.

Power over Ethernet Module

Chapter 1 Product Overview

Figure 3-27 shows the power adapter connector.

The Cisco 880 series ISRs can include an optional Power over Ethernet (PoE) module that provides power to 802.3af-compliant devices connected to FE ports 0 and 1.

The Cisco 890 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected to FE ports 0, 1, 2, and 3.

The PoE module is an option available only for the Cisco 880 series and 890 series ISRs and requires a 48

V external power adapter.

This function can be added to an 880 or 890 series router by installing the PoE adapter card in the router and inserting the PoE 48

Note The Cisco 880 series ISRs with embedded WLAN antennas require a single external power supply: a

W power supply for non-POE-enabled routers or a 60 W power supply for POE-enabled routers. For

the back panels of some of these routers, see Figure 1-17 and Figure 1-19.

V external power adapter.

3G Cellular Data WAN Connectivity

The 3G (Evolution Data Only [EVDO], Universal Mobile Telecommunications Systems [UMTS]) cellular interface is intended for use as a backup data link, but it can also be used as a primary WAN data link. The 3G technology is third-generation wide-area cellular technology that is used in voice telephony and broadband wireless data in a mobile environment.

Some Cisco 880G models come with a 34-mm express card slot ready for use with a commercial 3G card radio. The 3G express card slot is located on the front panel. For a list of supported 3G cards, see the

Cisco 880 Series Integrated Services Routers Data Sheet.

Other Cisco 880G models come with embedded WAN modems for use over GSM or CDMA networks. These routers have antenna connectors on the back panel. GSM routers have two SIM card slots. For information on configuring Cisco 880 series ISRs for 3G, see

3G (EV-DO Rev A) and Configuring Cisco EHWIC and 880G for 3.7G (HSPA+)/3.5G (HSPA).

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-38

Configuring Cisco EHWIC and 880G for

OL-16215-10

Page 55

Chapter 1 Product Overview

Wireless LAN Connectivity

The embedded Wi-Fi CERTIFIED™, 802.11a/b/g/n-compliant wireless AP is preinstalled in the router as an optional feature. The Cisco 860 series routers support autonomous features and network configurations. The Cisco features and network configurations.

The wireless AP does not have an external Console port. Use the router’s Console port as described in

Chapter 3, “Connecting a Terminal or PC to the Console Port.” To configure the wireless device, use the

Cisco IOS command-line interface (CLI).

Table 1-10 describes the radios and antennas for the Cisco 860 series, 880 series, and 890 series routers.

Note Cisco 860VAE ISRs do not support wireless LAN connectivity.

The 5-GHz radio operates in the Unlicensed National Information Infrastructure (UNII) 1, 2, 3, 5-GHz frequency bands.

Ta b l e 1-10 Wireless Device Radios and Antennas

880 series and 890 series routers support both autonomous and unified

Hardware Features

Radio Module Platform Radio Band

Single-band

802.11b/g/n

Cisco 860 and 880 series routers

2.4 GHz Up to 100 Mb/s Cisco 860 series:

draft 2.0 radio module

Note Cisco 860VAE

ISRs do not

Maximum Data Throughput

Mode Antenna

Three captive,

autonomous only

Cisco 880 series: autonomous and

omnidirectional dipole antennas: 2 dBi at

2.4 GHz

unified

support wireless LAN connectivity.

Single-band

802.11b/g/n radio module

Cisco 880 series routers with embedded WLAN antennas

2.4 GHz 100 Mb/s per radio, up to 200 Mb/s total

Autonomous and unified

Three embedded, omnidirectional antennas: 2 dBi at

2.4 GHz

Dual-band

802.11a/n and

802.11b/g/n radio modules

2.4 GHz

and 5 GHz

Three embedded, dual-band, omnidirectional antennas: 2 dBi at

2.4 GHz and 5 dBi at 5 GHz

Dual-band simultaneous

802.11a/n and

802.11b/g/n radio modules

1. Actual data rate is highly dependent on your wireless environment.

2. The antennas require some minor installation. They must be screwed onto the RP-TNC antenna connectors on the I/O side of the chassis. See the following document on Cisco.com for feature information:

Cisco 890 2.4 GHz

and 5 GHz

100 Mb/s per radio, up to 200 Mb/s total

Autonomous and unified

Three dual-band, removable,

2.4-GHz/5-GHz omnidirectional dipole RP-TNC antenna

http://www.cisco.com/en/US/docs/routers/access/wireless/hardware/notes/antdip.html

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

1-39

Page 56

Hardware Features

Supported Cisco Radio Antennas

The Cisco 891, Cisco 892, and Cisco 892F come with three removable dipole antennas that can be replaced using the Cisco approved antenna extenders listed in

Note Cisco supports only the antennas listed in Tabl e 1-11 with the Cisco 890 series dual-band radio module.

Ta b l e 1-11 Cisco Antennas Supported on the Cisco 890 Series ISRs

Cisco Part Number Antenna Type Maximum Gain Description

AIR-ANTM2050D-R Omnidirectional 2.0 dBi at 2.4 GHz

5.0 dBi at 5 GHz

AIR-ANTM4050V-R Omnidirectional 4.0 dBi at 2.4 GHz

5.0 dBi at 5 GHz

AIR_ANTM5560P-R Patch 5.5 dBi at 2.4 GHz

6.0 dBi at 5 GHz

This is the default antenna. It is a swivel-mount dipole dual-band blade antenna. For more information, see

Dipole Antenna (AIR-ANTM2050D-R).

Ceiling-mount dual-band antenna. This antenna has a clip that allows it to be mounted on a drop-ceiling cross member. For more information, see

Cisco Multiband Diversity Omnidirectional

Ceiling-Mount Antenna.

Wall-mount dual-band antenna. For more information, see

Corner-Mount, or Mast-Mount Antenna.

Chapter 1 Product Overview

Table 1-11.

Cisco Multiband Swivel-Mount

Cisco Multiband Wall-Mount,

Small Form-Factor Pluggable Port

The SFP port supports auto-media-detection, auto-failover, and remote fault indication (RFI), as described in the IEEE 802.3ah specification.

See the Cisco 892F data sheet for a list of supported SFPs.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-40

OL-16215-10

Page 57

Chapter 1 Product Overview

Hardware Features

Feature Summary

Table 1-12 summarizes the hardware features available in the Cisco 860 series, Cisco 880 series, and

Cisco 890 series ISRs.

Ta b l e 1-12 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs

Feature Description 860 Series 880 Series 890 Series

Reset button Resets the router configuration to the factory default. All models All models All models

FE1 built-in switch ports

GE4 built-in switch port

Console or AUX port

Resets the router configuration to customer configuration. 866VAE,

867VAE, 866VAE-K9, 867VAE-K9

Provides connection to 10/100BASE-T (10/100-Mb/s) Fast

Ethernet networks. The autosensing function in these

All models All models 891, 892,

routers eliminates the need for a crossover cable and enables the router to detect MDI2 or MDIX3 in any other PC or hub with a straight-through cable or a crossover cable.

Provides connection to 10/100/1000BASE-T (10/100/1000-Mb/s) Gigabit

Ethernet networks. The

866VAE-K9,

867VAE-K9 autosensing function in these routers eliminates the need for a crossover cable and enables the router to detect MDI5 or MDIX6 in any other PC or hub with a straight-through cable or a crossover cable.

Provides a connection to the terminal or PC for software

All models All models All models configuration or troubleshooting. The Console port may be configured as a virtual auxiliary port for dial backup and remote management.

Cisco 891, Cisco 892, and Cisco 892F have separate console and auxiliary ports.

— —

892F

— 892FSP,

896VA, 897VA, 897VAM, 897VAW, 897VAMW, 898EA

Cisco 892FSP has combined console and auxiliary port.

Security features Provides support for VPNs7, Cisco IOS Firewall, and

IPSec8. The Cisco 880 series routers also provide URL filtering.

Embedded wireless AP

Provides Wi-Fi CERTIFIED™ 802.11a/b/g/n compliance. The Cisco 860 series routers contain a single 802.11b/g/n radio. Some Cisco 880 series routers contain a single 802.11b/g/n radio while others contain dual 802.11a/n and 802.11b/g/n radios. The Cisco 890 series routers contain dual 802.11b/g/n and

802.11a/n radios.

FE WAN port Provides connection to 10/100BASE-T. Can be connected to

other network devices, such as a cable modem, an xDSL11 modem, or router. The router is capable of bridging and multiprotocol routing between the LAN and WAN ports.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

861, 867,

All models All models 866VAE-K9, 867VAE-K9

Wireless models

802.11b/g/n

Wireless

models

802.11b/g/n

and

802.11a/n

Wireless models

802.11b/g/n and

802.11a/n

861 881 891, 892,

892F

1-41

Page 58

Chapter 1 Product Overview

Hardware Features

Table 1-12 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

Feature Description 860 Series 880 Series 890 Series

GE WAN port 10/100/1000 GE WAN Port. 866VAE,

867VAE, 866VAE-K9, 867VAE-K9

VDSLoPOTS12

Provides connection to a VDSL network. — 887V —

port

ADSLoPOTS Provides ADSL connection over basic telephone service

— — — with Annex A and Annex B ITU G. 992.1 (ADSL), G.992.3 (ADSL2), and G.992.5 (ADSL).

ADSLoISDN Provides ADSL connection over ISDN. — — —

DSL Multi-mode (VDSL and ADSL2/2+)

Provides ADSL2/2+ or VDSL connection over POTS or ISDN (ISDN on 886VA only).

866VAE,

867VAE,

866VAE-K9,

867VAE-K9

Real-time clock (RTC)

USB port, Supports USB 1.1. Provides connection for USB devices

RTC provides nonvolatile date and time when the router is powered on. The RTC is used for verifying the validity of the Certification Authority stored on the router. It is backed up by a nonreplaceable lithium battery.

such as security tokens and flash memory.

The Cisco 880 series routers have a single USB port; the Cisco 890 series routers have two USB ports.

866VAE,

867VAE,

866VAE-K9,

867VAE-K9

866VAE,

867VAE,

866VAE-K9,

867VAE-K9

Cisco 880 series routers with embedded WLAN antennas have one USB 2.0 port.

— All models

886VA, 887VA,887V A-M

892FSP, 896VA, 897VA, 897VAM, 897VAW, 897VAMW, 898EA

All models All models

Cisco 892FSP and Cisco 860VAE series routers have one USB 2.0 port on the rear panel for temporary installation of a Cisco-approved USB memory device for maintenance purposes only. The port supports only USB 2.0. Refer to the product datasheet for the list of supported USB flash memory devices.

Note Cisco 860VAE series router USB port does not

support eToken.

PoE

(Optional) Provides power for 802.3af-compliant devices (such as phones) that are connected to the router.

— Models with

PoE

Models with PoE

The Cisco 880 series routers support a 2-port PoE module; the Cisco 890 series routers support a 4-port PoE module.

G.SHDSL14 port Provides 2-wire or 4-wire connection to a G.SHDSL

— 888 898EA network.

3G15 card slot Provides backup data link. — 3G models —

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-42

OL-16215-10

Page 59

Chapter 1 Product Overview

Hardware Features

Table 1-12 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

Feature Description 860 Series 880 Series 890 Series

Dying gasp Detects when the router is losing power, and sends a

power-fail signal to warn the DSLAM16 about the impending line drop.

Data BRI port Provides backup and remote management functions by

connecting to the ISDN service provider if the main VDSL or G.SHDSL link fails.

V.92 modem Provides dial backup and remote management functions if

the main WAN link fails.

FXO18 port An FXO interface connects local calls to a central office or

PBX. This is the interface a standard telephone provides.

FXS19/DID20 port

An FXS interface connects directly to a standard telephone, fax machine, or similar device. This interface supplies ringing voltage and dial tone to the station.

BRI voice port The ISDN BRI S/T voice interface provides a client-side

(TE) ISDN S/T physical interface for connection to an NT1 device that terminates an ISDN telephone network.

SFP21 port Supports auto-media-detection, auto-failover, and remote

fault indication (RFI), as described in the IEEE 802.3ah specification.

See the Cisco 892F data sheet for a list of supported SFPs.

1. FE = Fast Ethernet.

2. MDI = media-dependent interface in normal mode.

3. MDIX = media-dependent interface in crossover mode.

4. GE = Gigabit Ethernet.

5. MDI = media-dependent interface in normal mode.

6. MDIX = media-dependent interface in crossover mode.

7. VPN = Virtual Private Network.

8. IPsec = IP security.

9. This applies to most models of the Cisco 880 series routers.

10. This applies to Cisco 880 series routers with embedded, wireless antennas.

11. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line), VDSL (very-high-data-rate digital subscriber line), and G.SHDSL.

12. VDSLoPOTS = very-high-data-rate digital subscriber line 2 over plain old telephone service.

13. PoE = Power over Ethernet. This function can be added to an 880 or 890 series router by installing the PoE adapter card in the router and inserting the PoE 48-V external power adapter.

866VAE, 867VAE, 866VAE-K9, 867VAE-K9,

xDSL models

— xDSL

888EA,

xDSL models

892FSP, 896VA, 897VA, 897VAM, 897VAW, 897VAMW, 898EA

892 models, except for the 3G and SRST17 models

— — 891

— 881 SRST —

— SRST models —

— 887V —

— — 892F

models,

892FSP,

896VA,

897VA,

897VAM,

897VAW,

897VAMW,

898EA

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

1-43

Page 60

Hardware Features

14. G.SHDSL = (global industry standard) symmetrical high-speed DSL.

15. 3G = Third-Generation.

16. DSLAM = digital subscriber line access multiplexer.

17. SRST = Survivable Remote Site Telephony.

18. FXO = Foreign Exchange Office.

19. FXS = Foreign Exchange Station.

20. DID = Direct Inward Dialing.

21. SFP = small-form-factor pluggable.

Chapter 1 Product Overview

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

1-44

OL-16215-10

Page 61

CHAP T ER

Installing the Router

This chapter describes the equipment and the procedures for successfully installing the Cisco 860 series, 880 series, and 890 series Integrated Services Routers (ISRs), and contains the following sections:

• Equipment, Tools, and Connections, page 2-2

• Installing the Router, page 2-3

Note For compliance and safety information, see the Regulatory Compliance and Safety Information

Warning

Roadmap that ships with the router and the

Series and SOHO Series Routers.

All wireless LAN products in the 5.2/5.3GHz band cannot be used outdoors. Use the product only indoors.

Statement 372

Regulatory Compliance and Safety Information for Cisco 800

Warning

Read the installation instructions before connecting the system to the power source.

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54).

No user-serviceable parts inside. Do not open.

Statement 1052

Statement 1073

Statement 1004

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

2-1

Page 62

Equipment, Tools, and Connections

This section describes the equipment, tools, and connections necessary for installing your Cisco 860 series, 880 series, and 890 series ISRs. It contains the following topics:

• Items Shipped with your Router, page 2-2

• Additional Items, page 2-2

• Connections, page 2-3

• Ethernet Devices, page 2-3

Items Shipped with your Router

Unpack the box and verify that all items listed on the invoice were shipped with the router.

Table 2-1 lists the items and their quantities that are shipped with each router model.

Ta b l e 2-1 Items and Their Quantities That Are Shipped with the Cisco 860 Series, Cisco 880

Series, and Cisco 890 Series ISRs

Chapter 2 Installing the Router

Item

Straight-through RJ-45 Ethernet cable 1 — 1 1

ADSL RJ-11-to-RJ-11 straight-through cable — — — 1

RJ-11 DSL2 cable

DSL RJ-45-to-dual-RJ-11 breakout cable — n/a 1

RJ-45-to-DB-9 console cable 1 — 1 1

External 12 VDC power supply adapter 1 1 1 1

AC power supply cable with cable retention clip 1 1 1 1

Cisco Configuration Professional (Cisco CP) CD

1. By default, no cables are shipped with Cisco 860VAE models unless requested through the dynamic configuration tool.

2. DSL = digital subscriber line.

3. Shipped with Cisco 867 models only.

4. Shipped with Cisco 886, 887, 887M, and 886-J models only.

5. Shipped with Cisco 888E models only.

6. Cisco CP is optional by order and available only on some SKUs.

Additional Items

Cisco Cisco 860 Series Routers

1 1 1 1

860VAE

Series

Routers

n/a 1

Cisco 880 Series Routers

Cisco 890 Series Routers

The following items are not shipped with the router but are required for installation:

• ESD-preventive cord and wrist strap.

• Screws for mounting the router on a wall:

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

2-2

OL-16215-10

Page 63

Chapter 2 Installing the Router

Connections

Installing the Router

–

Two number-10 wood screws (round- or pan-head) with number-10 washers, or two number-10 washer-head screws, for mounting on a wall stud. The screws must be long enough to penetrate at least 3/4 in. (20 mm) into the supporting wood or metal wall stud.

–

Two number-10 wall anchors with washers, for mounting the router on a hollow-wall.

• Wire crimper for chassis grounding.

• Wire for connecting the chassis to an earth ground:

–

AWG 1 4 ( 2 mm2) or larger wire for NEC-compliant chassis grounding.

–

AWG 1 8 ( 1 mm2) or larger wire for EN/IEC 60950–compliant chassis grounding.

• Ring terminal with an inner diameter of 1/4 in. (5 to 7 mm), for NEC-compliant chassis grounding.

• Ethernet cables for connecting to the Fast Ethernet (FE) WAN and LAN ports.

Obtain a broadband or Ethernet connection from your service provider.

Ethernet Devices

Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs. Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports.

• If you plan to configure the software using Cisco IOS commands through the console port, provide

an ASCII terminal or a PC that is running terminal emulation software to connect to the console port.

• If you plan to connect a modem, provide the modem and modem cable.

• If you plan to use the Data BRI port, provide an NT1 device and an ISDN S/T cable.

• If you plan to use the cable-lock feature, provide a Kensington or equivalent locking cable.

Installing the Router

This section describes how to install the Cisco 860 series, 880 series, and 890 series ISRs. These routers can either be installed on a table top or other flat horizontal surface or be mounted on a wall. The Cisco

890 series ISRs may be mounted in a rack. This section also describes how to attach WLAN

antennas to the Cisco

• Warnings, page 2-4

• Installing Antennas, page 2-4

• Installing on a Table, page 2-7

• Mounting on a Wall, page 2-8

• Installing in a Rack, page 2-11

• Installing the Router Ground Connection, page 2-13

890 series routers. This section contains the following topics:

• Installing the FIPS Cover, page 2-14

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

2-3

Page 64

Installing the Router

Warnings

Chapter 2 Installing the Router

Warning

Note • Do not stack anything on top of the router.

This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use.

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.

Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.

• Do not cover or obstruct the router vents located on both sides and top of the routers; otherwise,

Statement 378

Statement 242

Statement 1024

overheating could occur and cause damage to the router.

• Place router in ventilated area to avoid local air heating.

Caution Do not cover or obstruct the router vents located on both sides of the router; otherwise, overheating could

occur and cause damage to the router.

Caution Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not

stack routers on a desktop. Excessive weight on top of the router could damage the chassis.

Caution Do not install the router or power supplies next to a heat source of any kind, including heating vents.

Caution The top surface of the router is hot since heat is dissipated through the top. Do not keep any object in

direct contact with the surface for a prolonged period.

Installing Antennas

The Cisco 890 series wireless routers have three reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel. The antennas that are shipped with the router are dual-band 2.4-GHz to 5-GHz omnidirectional dipole antennas.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

2-4

OL-16215-10

Page 65

Chapter 2 Installing the Router

272486

Installing the Router

Warning

Note Before you install the Cisco 890 series wireless router on a table, wall, or rack, connect the antennas to

All wireless LAN products in the 5.2/5.3GHz band cannot be used outdoors. Use the product only indoors.

Statement 372

the back panel. It is difficult to attach the antennas after the router is installed.

To attach the radio antennas to your wireless router, follow these steps:

Step 1 Manually screw the antennas tight to the RP-TNC connectors on the back of the router.

Figure 2-1 Attaching Antennas to the Router

Step 2 Orient the antennas. For optimum wireless performance, the antennas should be perpendicular with

respect to the floor.

a. If the router is being mounted on a desk, orient the antennas straight up. b. If the router is being mounted on a wall, orient the antennas perpendicular to the floor, as shown in

Figure 2-2 and Figure 2-3.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

2-5

Page 66

Installing the Router

Chapter 2 Installing the Router

Figure 2-2 Antennas Oriented Vertically Up

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

2-6

OL-16215-10

Page 67

Chapter 2 Installing the Router

Figure 2-3 Antennas Oriented Vertically Down

Installing the Router

Installing on a Table

To install the router on a table or other flat horizontal surface, firmly place the router on a table or other horizontal surface. Keep at least 1 inch (2.5 cm) of clear space beside the cooling inlet and exhaust vents.

Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the

“Installing the Router Ground Connection” section on page 2-13.

Note Do not place anything on top of the router.

274775

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

2-7

Page 68

Installing the Router

Mounting on a Wall

The Cisco 860 series, 880 series, and 890 series ISRs have mounting holes on the bottom of the chassis for mounting the unit on a wall or other vertical surface.

The mounting holes are bidirectional. You can hang the router with the front bezel facing upward or downward.

Keep at least 1 inch (2.5 cm) of clear space beside the cooling inlet and exhaust vents.

Tip When choosing a location for wall-mounting the router, consider cable limitations and wall structure.

To mount the router on a wall, follow these steps:

Step 1 Determine the required distance between mounting holes on the router. Figure 2-4 shows the wall-mount

holes located on the underside of the router.

Chapter 2 Installing the Router

Note For most router models, the distance between mounting holes is 8.2 inches (208 mm), as shown

Figure 2-4. For the Cisco 866 and Cisco 867 models, the distance is 7.85 inches (199 mm).

Verify the required distance before drilling the holes.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

2-8

OL-16215-10

Page 69

Chapter 2 Installing the Router

Figure 2-4 Wall-mount Holes on the Underside of the Router

Installing the Router

3.673 in.8.200 in.

5.961 in.

1 Wall-mount holes

Step 2 Insert the screws, with anchors, into the wall. Leave 1/8 inch (0.32 cm) between the screw head and the

wall. See

Step 3 Hang the router on the screw without forcibly pushing towards the wall side. The screw head may

Figure 2-5.

damage the protection wall inside. Place the power adapter on a nearby horizontal surface. See

Figure 2-5.

231987

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

2-9

Page 70

Installing the Router

231982

Chapter 2 Installing the Router

Figure 2-5 Router Mounted on the Wall

1 Two number-10 wood screws mounted on the

wall

3 Horizontal surface on which to place the

power adapter

2 Wall-mount holes 4 Distance between the screw head and the wall,

1/8 in. (0.32 cm)

Step 4 Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the

“Installing the Router Ground Connection” section on page 2-13.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

2-10

OL-16215-10

Page 71

Chapter 2 Installing the Router

278159

Installing in a Rack

The Cisco 890 series ISRs can be mounted in a rack. To install a Cisco 890 series ISR in a rack, follow these steps:

Step 1 Remove the screws, as shown in Figure 2-6.

Figure 2-6 Screw Locations

Installing the Router

1 Screws

Step 2 Using the screws provided, attach the rack-mount brackets to the Cisco 890 series ISR chassis, as shown

Figure 2-7. Use two screws on each side. Use a number 2 Phillips screwdriver to install the bracket

screws on both sides of the chassis.

Caution Do not over torque the screws. The recommended torque is 6 to 8 in-lb (0.7 to 0.9 N-m).

Figure 2-7 Attaching the Rack-mount Brackets to the Cisco 890 Series ISR

272484

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

2-11

Page 72

Installing the Router

Caution Chassis installation must allow unrestricted airflow for chassis cooling.

Chapter 2 Installing the Router

Warning

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.

Step 3 Using two screws for each side (supplied with the rack), attach the Cisco 890 series ISR with rack-mount

Statement 1006

brackets to a 19-inch rack. Start with the lower pair of screws first, resting the brackets on the lower screws while you insert the upper pair of screws.

Note Be sure to leave space above and below each unit in a rack to allow for cooling air circulation.

Note Do not stack equipment directly above the router. Keep at least 1 rack unit of space above the

router.

2-12

Tip The screw slots in the brackets are spaced to line up with every second pair of screw holes in the

rack. When the correct screw holes are used, the small threaded holes in the brackets line up with unused screw holes in the rack. If the small holes do not line up with the rack holes, you must raise or lower the brackets to the next rack hole.

Step 4 Place the power adapter on a nearby horizontal surface. Step 5 Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the

“Installing the Router Ground Connection” section on page 2-13.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Page 73

Chapter 2 Installing the Router

231981

Installing the Router Ground Connection

The router must be connected to a reliable earth ground. Install the ground wire in accordance with local electrical safety standards.

• For NEC-compliant grounding, use size 14 AWG (2 mm

with an inner diameter of 1/4 in. (5 to 7 mm).

• For EN/IEC 60950–compliant grounding, use size 18 AWG (1 mm

To install the ground connection, follow these steps:

Step 1 Strip one end of the ground wire to the length required for the ground lug or terminal. Step 2 Crimp the ground wire to the ground lug or ring terminal, using the wire crimper. Step 3 Attach the ground lug or ring terminal to the chassis, as shown in Figure 2-8. For a ground lug, use the

two provided screws with captive locking washers. For a ring terminal, use one of the screws provided. Tighten the screws to a torque of 8 to 10

Figure 2-8 Chassis Ground Connection Using Ring Terminal

) or larger copper wire and a ring terminal

in-lb (0.9 to 1.1 N-m).

Installing the Router

) or larger copper wire.

1 Ring terminal

Step 4 Connect the other end of the ground wire to a known reliable earth ground point at your site.

After you install and properly ground the router, you can connect the power wiring, the WAN and LAN cables, and the cables for administrative access as required for your installation.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

2-13

Page 74

Installing the Router

284921

Installing the FIPS Cover

Perform the following steps to install the FIPS cover in the router:

Step 1 Remove the four mounting screws of the top cover.

Chapter 2 Installing the Router

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

2-14

OL-16215-10

Page 75

Chapter 2 Installing the Router

284922

Detail A

Adapter

Plate

Step 2 Install the left-side FIPS cover, as shown in detail A.

Installing the Router

Step 3 Rotate and bring into the close position to hinge to the correct hexagon. Step 4 Place the adapter plate before closing by aligning the mounting holes.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

2-15

Page 76

Installing the Router

284924

Step 5 Secure the FIPS cover with two mounting screws.

Chapter 2 Installing the Router

284923

Step 6 Install the right-side FIPS cover the same way as the left-side FIPS cover. Step 7 View after both covers are installed.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

2-16

OL-16215-10

Page 77

Chapter 2 Installing the Router

Step 8 If the FIPS covers are installed with the rack mount brackets, the adapter plates are not required in the

installation.

Installing the Router

284925

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

2-17

Page 78

Installing the Router

Chapter 2 Installing the Router

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

2-18

OL-16215-10

Page 79

CHAP T ER

Connecting the Router

This chapter describes how to connect Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated Services Routers (ISRs) to Ethernet devices, Power over Ethernet (PoE), and a network. The chapter contains the following sections:

• Safety Warnings, page 3-2

• Preparing to Connect the Router, page 3-4

• Connecting a PC, Server, or Workstation, page 3-5

• Connecting a Phone, page 3-6

• Connecting an External Ethernet Switch, page 3-7

• Connecting the V.92 modem Port, page 3-8

• Connecting a Terminal or PC to the Console Port, page 3-9

• Connecting a Modem to the Auxiliary Port, page 3-10

• Connecting the 3G Card, page 3-11

• Installing the 3G Adapter for Extended Cable/Antenna, page 3-17

• Connecting a Data BRI Port, page 3-21

OL-16215-10

• Connecting an FE Line to an FE WAN Port, page 3-23

• Connecting a GE Line to an GE WAN Port, page 3-24

• Connecting an xDSL Line, page 3-25

• Connecting Power over Ethernet, page 3-27

• Connecting the AC Adapter, page 3-28

• Connecting an FXS Line, page 3-32

• Connecting an FXO Line, page 3-34

• Connecting a Voice ISDN BRI Line, page 3-35

• Connecting a Small Form-Factor Pluggable Module, page 3-37

• Verifying Connections, page 3-40

Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap

that ships with the router and

SOHO Series Routers.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

Regulatory Compliance and Safety Information for Cisco 800 Series and

3-1

Page 80

Safety Warnings

Note The illustrations in this chapter show a wireless router with antennas attached. Non-wireless routers do

not have antennas or antenna connectors on the back panel. However, the procedures for connecting devices to the router are the same for both wireless and non-wireless routers.

Note Depending on the features available for your router, some content in this chapter may not apply to your

router.

Safety Warnings

Chapter 3 Connecting the Router

Warning

When installing the product, please use the provided or designated connection cables/power cables/AC adaptors/batteries. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” or “CSA” shown on the cord), not regulated with the subject law by showing “PSE” on the cord, for any other electrical devices than products designated by CISCO.

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

This equipment has been designed for connection to TN and IT power systems.

Take care when connecting units to the supply circuit so that wiring is not overloaded.

Statement 1015

Statement 371

Statement 1007

Statement 1018

Warning

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.

Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first.

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

3-2

Statement 1021

Statement 1026

OL-16215-10

Page 81

Chapter 3 Connecting the Router

Safety Warnings

Warning

Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.

Statement 1035

Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

Statement 1036

Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

Statement 1037

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

To report a gas leak, do not use a telephone in the vicinity of the leak.

Statement 1038

Statement 1039

Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network voltages.

Statement 1041

Warning

This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11 port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming call.

Statement 1042

No user-serviceable parts inside. Do not open.

Installation of the equipment must comply with local and national electrical codes.

Statement 1052

Statement 1073

Statement 1074

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

3-3

Page 82

Preparing to Connect the Router

Before you connect the router to the devices, install the router according to the instructions in “Installing

the Router” section on page 2-1

Preventing Damage to the Router

To prevent damage to your router, follow these guidelines when connecting devices to your router:

• Turn off power to the devices and to the router until all connections are completed.

Caution Do not turn on the devices until after you have completed all connections to the router.

• Connect the color-coded cables supplied by Cisco to the color-coded ports on the back panel.

• If you must supply your own cable, see “Technical Specifications” section on page A-1 for cabling

specifications. If this appendix does not provide specifications for a particular cable, we strongly recommend ordering the cable from Cisco.

Chapter 3 Connecting the Router

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

3-4

OL-16215-10

Page 83

Chapter 3 Connecting the Router

231989

Connecting a PC, Server, or Workstation

To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps:

Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Figure 3-1 shows

a Cisco 888W router connected to a PC.

Figure 3-1 Connecting a Server, PC, or Workstation

Connecting a PC, Server, or Workstation

1 Yellow Ethernet cable supplied with the router 3 RJ-45 port on the network interface card 2 Ethernet switch port on the router

Step 2 Connect the other end of the cable to the RJ-45 port on the network interface card (NIC) that is installed

in the PC, server, or workstation.

Step 3 (Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports.

Note Use the Cisco Configuration Express to configure the Internet connection settings. See

Cisco Configuration Professional Quick Start Guide for more information.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

3-5

Page 84

Connecting a Phone

To connect an 802.3af-compliant phone to an Ethernet switch port, follow these steps:

Note A power source must be provided for the phone to function. This can be done in two ways: the phone

can be powered via the PoE function using the PoE enabled Ethernet ports, or by using an external AC power source connected to the phone.

Step 1 Connect one end of the yellow Ethernet cable to Ethernet switch port 0 or port 1 on the router. Figure 3-2

shows a Cisco 888W router connected to a phone.

Figure 3-2 Connecting a Phone

Chapter 3 Connecting the Router

ABC3DEF

JKLGHI6MNO

TUVPQRS9WXYZ

OPER

1 Yellow Ethernet cable 3 RJ-45 port on a phone 2 Ethernet switch port 1 on the router

270551

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

3-6

OL-16215-10

Page 85

Chapter 3 Connecting the Router

Step 2 Connect the other end of the cable to the RJ-45 port on the phone.

Connecting an External Ethernet Switch

If more than four PCs in an office must be connected to each other, you can add Ethernet connections to the router by connecting an external Ethernet switch to the Ethernet switch on the router.

To connect an external Ethernet switch to an Ethernet switch port on the router, complete the following steps:

Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Figure 3-3 shows

a Cisco 888W router connected to an Ethernet switch.

Figure 3-3 Connecting to an Ethernet Switch

Connecting an External Ethernet Switch

1 X

SYSTEM

RPS

STA

T US

UTIL

D U

PLX

SPE

1 5

1 X

2 X

1 6

1 5

2 X

1 6 X

Catalyst 3500

SERIES

INLINE POWER

231986

1 Ethernet switch port on the router 3 Yellow CAT5 Ethernet cable,

RJ-45–to–RJ-45, connecting to an external Ethernet switch port

2 Available port on the external Ethernet switch

Step 2 Connect the other end of the cable to the available port on the Ethernet switch to add additional Ethernet

connections.

Step 3 Turn on the Ethernet switch.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

3-7

Page 86

Connecting the V.92 modem Port

272387

Connecting the V.92 modem Port

Chapter 3 Connecting the Router

Warning

Statement 1026

For dialup connection to your service provider network through the V.92 port, follow the steps given after

Figure 3-4, which show this connection.

Figure 3-4 Connecting to Your Service Provider Through the V.92 port

1 V.92 port on the router 2 Telephone wall outlet

To connect the router to your service provide network through the V.92 port, follow these steps:

Step 1 Connect one end of the straight-through R-J11 cable to the V.92 port. Step 2 Connect the other end of the straight through R-J11 cable to an RJ-11 telephone wall outlet.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

3-8

OL-16215-10

Page 87

Chapter 3 Connecting the Router

231990

Connecting a Terminal or PC to the Console Port

Connect a terminal or PC to the Console Auxiliary (Aux) port either to configure the software by using the CLI or to troubleshoot problems with the router.

To connect a terminal or PC to the console port on the router and access the CLI, follow these steps:

Step 1 Connect the RJ-45 end of a DB-9–to–RJ-45 serial cable to the RJ-45 Console Aux port on the router.

Figure 3-5 shows the RJ-45 end of the serial cable connected to the Console Aux port on the router.

Figure 3-5 Connecting a Terminal or PC to the Console Port

OL-16215-10

1 RJ-45 connector to the Console Aux port on

2 DB-9 connector

the router

Step 2 Connect the DB-9 end of the DB-9–to–RJ-45 serial cable to the to the COM port on your laptop or PC.

Note Some laptops and PCs do not come with DB-9 serial port connectors and may require a

USB-to-serial port adapter.

Step 3 To communicate with the router, start a terminal emulator application.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

3-9

Page 88

Connecting a Modem to the Auxiliary Port

Terminal Emulator Settings

Use the following settings for the terminal emulator connection:

• 9600 baud

• 8 data bits, no parity

• 1 stop bit

• No flow control

When the terminal emulator establishes communications, the router prompt is displayed.

For more information on terminal emulation settings, see Applying Correct Terminal Emulator Settings

for Console Connections.

Connecting a Modem to the Auxiliary Port

To connect a modem to the router, follow these steps:

Chapter 3 Connecting the Router

Step 1 Connect the RJ-45 end of the adapter cable to the Aux port on the router as shown in Figure 3-6.

Figure 3-6 Connecting a Modem to the Aux Port

272386

1 Aux port (RJ-45) 3 DB-9 to DB-25 modem adapter (if required) 2 Light blue console cable 4 Modem

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

3-10

OL-16215-10

Page 89

Chapter 3 Connecting the Router

Step 2 Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter. Step 3 Connect the DB-25 end of the modem adapter to the modem. Step 4 Make sure that your modem and the router auxiliary port are configured for the same transmission speed

(up to 115200 bits per second [b/s] is supported) and support mode control with data carrier detect (DCD) and data terminal ready (DTR).

Connecting the 3G Card

Note For information on embedded multiband, multiservice WAN modems, see Configuring Cisco EHWIC

and 880G for 3G (EV-DO Rev A) and Configuring Cisco EHWIC and 880G for 3.7G (HSPA+)/3.5G (HSPA).

Note The Cisco 880G router does not support online insertion and removal (OIR) of the third-generation (3G)

card. You must enter the shutdown command on the cellular interface before you remove the 3G card from the router.

Connecting the 3G Card

To connect and secure the 3G card, follow these steps:

Step 1 Align the 3G card to the 3G express card slot, as shown in Figure 3-7. Keep the card parallel to the

surface and firmly push the card into the slot.

Tip Holding the 3G card on the flat metal surface makes it easier to align and insert the 3G card.

Note When inserting the card into the 3G express card slot, you may hear a metal-on-metal sound as

the 3G card rubs against the internal metal cage. The 3G card is designed to fit tightly into the 3G express card slot. Firm pressure may be required to insert the card.

Note Global System for Mobile Communications (GSM) customers need to insert a SIM card,

provided by their network carrier, into the 3G card.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

3-11

Page 90

Connecting the 3G Card

271473

271474

Front View Back View

Chapter 3 Connecting the Router

Figure 3-7 Inserting the 3G Card

1 3G card with the Cisco logo facing up 4 Screw holes for locking bracket 2 3G express card slot 5 Pin holes for aligning the locking bracket 3 Notches on the 3G card 6 SIM slot (in HSPA1 cards only)

1. HSPA = High-Speed Packet Access.

Step 2 Open the top of the anti-theft locking bracket, as shown in Figure 3-8.

Figure 3-8 Opening the Anti-theft Locking Bracket

1 Pins on the locking bracket for alignment

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

3-12

OL-16215-10

Page 91

Chapter 3 Connecting the Router

Step 3 Slide the opened locking bracket under the 3G card. The locking bracket should align with the notches

on either side of the 3G card, as shown in inserted into the corresponding holes in the router.

Figure 3-9 Installing the Locking Bracket

Connecting the 3G Card

Figure 3-9, and the pins on the locking bracket should be

1 3G card 3 Notch on the 3G card 2 Locking bracket

271726

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

3-13

Page 92

Connecting the 3G Card

271476

Step 4 Close the locking bracket, as shown in Figure 3-10.

Chapter 3 Connecting the Router

Figure 3-10 Closing the Locking Bracket

271580

1 3G card 2 Locking bracket

Step 5 Insert the screws, as shown in Figure 3-11, and tighten with a number 2 Phillips screwdriver.

Figure 3-11 Inserting the Screws

1 3G card 3 Screws 2 Locking bracket 4 Screw holes on the locking bracket

Step 6 To connect the antenna to the 3G card, insert the antenna connector into the antenna connector receptacle

on the 3G card.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

3-14

OL-16215-10

Page 93

Chapter 3 Connecting the Router

272653

Note The antenna connector receptacle may be located on the left, right, or front of the 3G card, depending

on your card.

Figure 3-12 shows the antenna connected to the 3G card with an SSMB type plug, and Figure 3-13 shows

the antenna with the SMK-TS-9 connector.

Figure 3-12 Antenna connected to the 3G Card with SSMB connector

Connecting the 3G Card

1 Antenna on a cradle 3 Antenna connector receptacle

2 Antenna SSMB connector

1. The antenna connector receptacle is located on either the left, right or front of the card for different SKUs. Please locate the receptacle of your card before plugging in the cable.

OL-16215-10

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

3-15

Page 94

Connecting the 3G Card

279085

Original

antenna assembly

SMK-TS-9

connector

Cable

Chapter 3 Connecting the Router

Figure 3-13 Antenna with the SMK-TS- 9 Connector

If you are using an extension cable, you must attach the 3G adapter for extended cable antenna to the body of the router. Depending on the SKU ordered, the adapters come with different connectors.

Table 3-1 lists the different adapters and SKUs supported by each adapter. For instructions on how to

install the adapter, see the “Installing the 3G Adapter for Extended Cable/Antenna” section on

page 3-17. Otherwise, follow Step 7.

Ta b l e 3-1 3G Adapters and Supported SKUs

3G Adapter SKU Description SKUs Supported

3G-ACC-SMKTS9-TNC 3G adapter for extended cable/antenna

with an SMK-TS-9 to TNC connector. Use this with the pentaband dipole indoor antenna (3G-ANTM-SMKTS9).

3G-ACC-SSMB-TNC 3G adapter for extended cable/antenna

with an SSMB to TNC connector. Use this with the pentaband dipole indoor antenna shipped with your product.

Step 7 Clean the flat surface to which you will affix the antenna.

PCEX-3G-HSPA-R6, CISCO881G-G-K9

PCEX-3G-HSPA, PCEX-3G-HSPA-A, PCEX-3G-CDMA-S, PCEX-3G-CDMA-V, PCEX-3G-CDMA-B, CISCO881G-A-K9, CISCO881G-S-K9, CISCO881G-V-K9

3-16

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Page 95

Chapter 3 Connecting the Router

279124

Installing the 3G Adapter for Extended Cable/Antenna

Step 8 Remove the protective tape from the adhesive on the bottom of the antenna cradle, then firmly press the

cradle to the flat surface.

Installing the 3G Adapter for Extended Cable/Antenna

For better signal and reception, if you are using the Cisco 3G Adapter for Extended Cable/Antenna, 3G-ACC-SMKTS9-TNC, follow these steps to install it:

Step 1 Locate and remove the Phillips screw on the left side of the router as shown in Figure 3-14. Keep the

screw aside for Step 4.

Figure 3-14 Locating the Phillips Screw

1 Phillips screw on the left side of router 2 Air vent holes to be aligned with adapter

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

3-17

Page 96

Installing the 3G Adapter for Extended Cable/Antenna

279122

279123

Step 2 Locate the hooks on the adapter as shown in Figure 3-15.

Figure 3-15 Locating the Hooks on the Adapter

1 Hooks on the adapter

Chapter 3 Connecting the Router

Step 3 Align and insert the hooks of the adapter into the air vent holes on the left side router body as shown in

Figure 3-16.

Figure 3-16 Inserting the Hooks

1 Hooks aligned and inserted into the router.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

3-18

OL-16215-10

Page 97

Chapter 3 Connecting the Router

279091

Step 4 Align the circular adapter hole with the hole on the router chassis from where you removed the screw in

Step 1 and use the screw to attach the adapter to the router as shown in Figure 3-17.

Figure 3-17 Attaching the Adapter

Installing the 3G Adapter for Extended Cable/Antenna

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

3-19

Page 98

Installing the 3G Adapter for Extended Cable/Antenna

Step 5 Connect the extension cable to the 3G card, as described in the “Connecting the 3G Card” section on

page 3-11. The complete assembly is shown in Figure 3-18.

Figure 3-18 Adapter Connected to 3G Card and Router Chassis

Chapter 3 Connecting the Router

1 Router chassis 4 SSMB or SMK-TS-9 connector 2 3G adapter for extended cable/antenna 5 3G card inserted into the router 3 Cable 6 3G card

Now the adapter is ready for use with the extension cable. Tab le 3-2 lists the loss information for the ultra-low-loss (ULL) LMR 400 cables available with the adpater for the 3G fixed platforms.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

3-20

279089

OL-16215-10

Page 99

Chapter 3 Connecting the Router

Ta b l e 3-2 Cisco Adapter Cables for Use with 3G Fixed Routers

Cisco Product Number

3G-ACC-SSMB-TNC 14.5 inches 0.66 dB 2100

3G-ACC-TS9-TNC 13.5 inches 0.62 dB 2100

Note Antenna orientation can increase or decrease signal reception due to polarization. Typically, an SP’s

transmitting antenna on the BTS is a vertically polarized omnidirectional antenna, which means the electromagnetic waves are transmitted from it in a vertical plane. Hence, the receiving antenna needs to be vertically oriented too in order to receive the best signal. As the angle of the antenna orientation is changed from vertical to horizontal, only an angular component of the signal is picked up by the antenna. Therefore, if the antenna orientation is horizontal, the antenna picks up the least signal. The signal is received by the antenna as a result of it bouncing off of reflective surfaces. Hence, depending on where the antenna is placed, it may receive different signal strengths. However, the recommended position is vertical.

Antenna Adapter Length

Connecting a Data BRI Port

Insertion Loss Frequency (MHz)

For additional information on all the available cables and antennas available for 3G, go to:

http://www.cisco.com/en/US/docs/routers/access/1800/1861/software/feature/guide/mrwlsgsm.html#w p1262730

Connecting a Data BRI Port

You can connect the Data BRI port to the ISDN service provider as a backup link to the WAN port in case the primary xDSL (general term referring to various forms of DSL, including global industry standard symmetrical high-speed DSL [G.SHDSL]) WAN service fails. The Data BRI connection is not available on the third-generation (3G) models.

The cabling requirements for the ISDN S/T connection are as follows:

• You must provide two unshielded Category 5 cables. The first cable connects the NT1 box to the

splitter, and the second cable connects the splitter to the wall jack.

• There are RJ-45 connectors at both ends of the default orange ISDN S/T cable. However, an

RJ-45–to–RJ-11 ISDN S/T cable is available upon request if the wall jack at the site requires an RJ-11 connector. Contact your router reseller for the appropriate cable.

Caution Both LAN and WAN ports use RJ-45 connectors. Use caution when connecting cables to these

connectors. To avoid damage to the router, do not connect telephone-network voltage (TNV) circuits (such as ISDN or DSL circuits) to safety extra-low voltage (SELV) circuits (such as LAN circuits).

Although the following procedure shows a Cisco 888W data router, this procedure applies to all Cisco

880 series router with a Data BRI port.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

3-21

Page 100

Connecting a Data BRI Port

To connect the Data BRI port to the ISDN service provider, follow these steps:

Step 1 Connect one end of the orange ISDN S/T cable to the Data BRI port on the router. Figure 3-19 shows a

Data BRI connection.

Figure 3-19 Connecting the Data BRI Port to the ISDN Line

Chapter 3 Connecting the Router

231991

1 Data BRI port on the router 6 U-port on the NT1 box 2 ISDN S/T cable 7 xDSL splitter (provided by the xDSL service

provider)

3 Network termination 1 (NT1) box 8 Telephone line port on the splitter 4 S/T port on the NT1 box 9 Telecommunication service port on the

splitter

5 Unshielded CAT 5 cable 10 Wall jack

Step 2 Connect the other end of the orange ISDN S/T cable to the S/T port on the NT1 box. Step 3 Connect the first unshielded CAT 5 cable from the U-port on the NT1 box to the telephone line port on

the splitter.

Step 4 Connect the second unshielded Category 5 cable from the telecommunication service port on the splitter

to the wall jack to allow a link to the network service provider.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

3-22

OL-16215-10