Cisco Systems 6500 WS-X6066-SLB-APC User Manual
Contents
Catalyst 6500 Series Switch Content Switching
Module Installation Note
Product Number: WS-X6066-SLB-APC
This publication describes how to install the Content Switching Module (CSM) in the Catalyst 6500
series switches, including the software and hardware requirements.
This publication contains these sections:
• Safety Overview, page 2
• Front Panel Description, page 7
• Environmental and System Requirements, page 9
• Installing the CSM, page 11
• Verifying the Installation, page 20
• Using the CLI, page 20
• Related Documentation, page 21
• Translated Safety Warnings, page 21
• Obtaining Documentation, page 24
• Documentation Feedback, page 25
• Obtaining Technical Assistance, page 25
• Obtaining Additional Publications and Information, page 26
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2004 Cisco Systems, Inc. All rights reserved.
Safety Overview
Safety Overview
Warning
Waarschuwing
Varoitus
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
SAVE THESE INSTRUCTIONS
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
Statement 1071
2
SÄILYTÄ NÄMÄ OHJEET
Attention
Catalyst 6500 Series Switch Content Switching Module Installation Note
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
78-15751-04
Safety Overview
Warnung
Avvertenza
Advarsel
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
Aviso
¡Advertencia!
TA VARE PÅ DISSE INSTRUKSJONENE
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
78-15751-04
Catalyst 6500 Series Switch Content Switching Module Installation Note
3
Safety Overview
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
Catalyst 6500 Series Switch Content Switching Module Installation Note
4
78-15751-04
Safety Overview
Aviso
Advarsel
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
78-15751-04
Catalyst 6500 Series Switch Content Switching Module Installation Note
5
Safety Overview
Catalyst 6500 Series Switch Content Switching Module Installation Note
6
78-15751-04
Front Panel Description
Front Panel Description
This section describes the physical attributes of the Content Switching Module .
Figure 1 shows the CSM front panel.
Figure 1 Content Switching Module Front Panel
Status
LED
Note The RJ-45 connector is covered by a removable plate.
RJ-45 (Test)
connector
CSM
105789
78-15751-04
Catalyst 6500 Series Switch Content Switching Module Installation Note
7
Front Panel Description
Status LED
Note For more information on the supervisor engine LEDs, refer to the Catalyst 6500 Series Switch Module
At startup, the CSM initializes various hardware components and communicates with the supervisor
engine. The Status LED indicates the supervisor engine operations and the initialization results. During
the normal initialization sequence, the status LED changes from off to red, orange, and green.
Installation Guide.
Table 1 describes the Status LED operation.
Table 1 Content Switching Module Status LED
Color Description
Off
• The module is waiting for the supervisor engine to provide power.
• The module is not online.
• The module is not receiving power, which could be caused by the following:
–
Power is not available to the CSM.
Red • The module is released from reset by the supervisor engine and is booting.
Orange
Green
Green to orange
1. Enter the show environment temperature mod command to display the temperature of each of four sensors on the CSM.
2. CLI = command-line interface.
RJ-45 Connector
–
Module temperature is over the limit1.
• If the boot code fails to run, the LED stays red after startup.
• The module is initializing hardware or communicating with the supervisor
engine.
• A fault occurred during the initialization sequence.
• The module has failed to download its Field Programmable Gate Arrays
(FPGAs) at startup but continues with the remainder of the initialization
sequence and provides the module online status from the supervisor engine.
• The module has not received module online status from the supervisor engine.
This problem could be caused by the supervisor engine detecting a failure in
an external loopback test that it issued to the CSM.
• The module is operational; the supervisor engine has provided module online
status.
• The module is disabled through the supervisor engine CLI
2
using the set
module disable mod command.
The RJ-45 connector, which is covered by a removable plate, is used to connect a management station
device or a test device. This connector is used by field engineers to perform testing and to obtain dump
information.
Catalyst 6500 Series Switch Content Switching Module Installation Note
8
78-15751-04
Environmental and System Requirements
This section describes the environmental and system requirements.
• Environmental Requirements, page 9
• System Requirements, page 9
• Memory Requirements, page 9
• Power Supply, page 10
• Hardware Supported, page 10
• Software Compatibility, page 10
Environmental Requirements
Table 2 lists the environmental requirements for the CSM.
Table 2 CSM Environmental Requirements
Environmental and System Requirements
Item Specification
Temperature, ambient operating 0
Temperature, ambient nonoperating –40
Humidity (RH), ambient (noncondensing)
operating
Nonoperating relative humidity (noncondensing) 5% to 95%
System Requirements
Before you install the CSM i the Catalyst 6500 series switch, make sure that the switch meets the
hardware and software requirements listed in this section.
Caution You can use the Multilayer Switch Feature Card (MSFC), which is internal to the Catalyst 6500 series
switch, to route traffic on either the client side or the server side of the CSM, but not both simultaneously
(unless policy-based routing is used).
Memory Requirements
The CSM memory is not configurable.
CSM software release 4.1(2) requires Cisco IOS Software Release 12.1(8a)EX or higher. However, the
features new to CSM release 4.1(2) are available only with Cisco IOS Software Release 12.1(19) E and
Catalyst operating system software release 7.6 and higher.
o
to 40oC (32o to 104oF)
o
to 70oC (–40o to 158oF)
10% to 90%
78-15751-04
Catalyst 6500 Series Switch Content Switching Module Installation Note
9
Loading...