CipherLab 8500, 8570, 8580, 8590 Reference Manual

8500 Series Mobile Computer

8500/8570/8580/8590

Version 2.11

The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited.

Due to continued product development this information may change without notice. The information and intellectual property contained herein is confidential between CIPHERLAB and the client and remains the exclusive property of CIPHERLAB CO., LTD. If you find any problems in the documentation, please report them to us in writing. CIPHERLAB does not warrant that this document is error-free.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of CIPHERLAB CO., LTD.

For product consultancy and technical support, please contact your local sales representative. Also, you may visit our web site for more information.

The CipherLab logo is a registered trademark of CIPHERLAB CO., LTD.

Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and/or other countries.

Bluetooth is a trademark of Bluetooth SIG, Inc., U.S.A.

Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.

The editorial use of these names is for identification as well as to the benefit of the owners, with no intention of infringement.

CIPHERLAB CO., LTD.

Website:

http://www.cipherlab.com

IMPORTANT NOTICES

FOR USA

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FOR CANADA

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled "Digital Apparatus," ICES-003 of Industry Canada.

Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Classe B prescrites dans la norme sur le material brouilleur: "Appareils Numeriques," NMB-003 edictee par l'Industrie.

FOR HAND-HELD PRODUCT WITH RF FUNCTIONS

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. It only operated in hand-held used.

If you only transfer data to Host by WLAN/Bluetooth, please keep the minimum distance 20 cm between machine & your body.

FOR PRODUCT WITH LASER

Per FDA and IEC standards, the scan engines described in this manual are not given a laser classification. However, the following precautions should be observed:

CAUTION

This laser component emits FDA / IEC Class 2 laser light at the exit port. Do not stare into beam.

SAFETY PRECAUTIONS

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

 The use of any batteries or charging devices, which are not originally sold or

manufactured by CipherLab, will void your warranty and may cause damage to human body or the product itself.

 DO NOT disassemble, incinerate or short circuit the battery.  DO NOT expose the scanner or the battery to any flammable sources.  For green-environment issue, it's important that batteries should be recycled in a

proper way.

 Under no circumstances, internal components are self-serviceable.  The charging and communication cradle uses an AC power adaptor. A socket outlet

shall be installed near the equipment and shall be easily accessible. Make sure there is stable power supply for the mobile computer or its peripherals to operate properly.

CARE & MAINTENANCE

 This mobile computer is intended for industrial logistics use. The mobile computer is

rated IP 64, however, it may do damage to the mobile computer when being exposed to extreme temperatures or soaked wet.

 When the body of the mobile computer gets dirty, use a clean and wet cloth to wipe

off the dust. DO NOT use/mix any bleach or cleaner. Always keep the LCD dry.

 For a liquid crystal display (LCD) or touch screen, use a clean, non-abrasive, lint-free

cloth to wipe dust off the screen. DO NOT use any pointed or sharp object to move against the surface.

 If you want to put away the mobile computer for a period of time, download the

collected data to a host computer, and then take out the battery pack. Store the mobile computer and battery pack separately.

 When the mobile computer resumes its work, the main and backup batteries will take

a certain time to become fully charged.

 If you shall find the mobile computer malfunctioning, write down the specific scenario

and consult your local sales representative.

RELEASE NOTES

Version Date Notes

2.11 July 21, 2008

2.10 Apr. 24, 2008 New Word template applied

2.01 Aug. 10, 2007

2.00 May 19, 2007

1.07 Oct. 31, 2006

1.06 July 27, 2006

1.05 June 22, 2006

1.04 June 16, 2006

1.03 May 23, 2006 Company name changed to CIPHERLAB CO., LTD. since April 2006

1.02 Apr. 4, 2006

1.00 Mar. 1, 2006 Initial release

 Modified: section 1.3.3 44-key Keypad – “59-key” corrected to

“44-key”

 Modified: section 1.5.9 Reader – Defaults updated  Modified: section 4.1.8.(4) GSM/GPRS Menu> Security  Modified: section 4.1.8.(4) GSM/GPRS Menu> GPRS Settings  New release

 Modified: section 1.5.9 List by standards for RFID tags  Modified: section 1.5.10 Bluetooth specification  Modified: section 4.1.7 Bluetooth Menu > Security – max. 16

characters for PIN

 Modified: section 1.3.9 Reader – RFID (add ICODE)  Modified: section 2.5.2 Front Panel (LEDs of cradle)  New: section 4.1.8(2) System Menu > IR Network Menu  Modified: section 1.3.9 Reader – RFID  Modified: section 4.1.1 Information – add RFID version  FCC Regulations – Class B statement  Modified: section 1.3.9 Reader –

Enabled

Symbologies Supported &

 New: Safety Precaution  Modified: Care & Maintenance  Modified: section 1.2.3 Dimensions & Specifications  Modified: section 1.3.4 Keypad – Screen Icons  Modified: section 1.3.5 LCD – Screen & Backlight Settings  Modified: section 1.3.12 Application Software to include AG and

CipherNet

 Modified: sections 2, 2.5 ~ 2.7  Modified: sections 3.1 & 3.3  Modified: section 4.1.2 Screen Calibration  Modified: section 4.1.6 Load Program via Bluetooth  Update drawings  Load Program via Bluetooth

CONTENTS

IMPORTANT NOTICES ...................................................................................................................... - 3 -

For USA .......................................................................................................................................... - 3 -

For Canada .................................................................................................................................... - 3 -

For Hand-held Product with RF Functions ................................................................................... - 3 -

For Product with Laser .................................................................................................................. - 4 -

Safety Precautions ........................................................................................................................ - 4 -

Care & Maintenance ..................................................................................................................... - 4 -

RELEASE NOTES.............................................................................................................................. - 5 -

INTRODUCTION.................................................................................................................................... 1

Getting Familiarized with 8500........................................................................................................ 2

Installing the Hand Strap............................................................................................................. 3

Installing the Pistol Grip............................................................................................................... 4

Charging the Battery .................................................................................................................... 5

Dimensions........................................................................................................................................ 6

Features............................................................................................................................................. 7

Inside the Package............................................................................................................................ 7

Accessories........................................................................................................................................ 8

USING 8500 MOBILE COMPUTER....................................................................................................... 9

1.1 Battery ......................................................................................................................................... 9

1.1.1 Inserting the Battery ........................................................................................................10

1.1.2 Charging the Battery ........................................................................................................ 11

1.1.3 Caution of Low Battery Charge........................................................................................11

1.1.4 Power Management.........................................................................................................11

1.2 Memory .....................................................................................................................................12

1.2.1 Caution of Data Loss........................................................................................................12

1.2.2 Upgradeable Memory.......................................................................................................12

1.3 Keypad ......................................................................................................................................13

1.3.1 Screen Icons..................................................................................................................... 14

1.3.2 24-key Layout................................................................................................................... 15

1.3.3 44-key Keypad..................................................................................................................17

1.4 LCD ............................................................................................................................................ 19

1.4.1 Adjusting the Backlight ....................................................................................................19

1.4.2 calibrating the Screen......................................................................................................20

1.5 Notifications.............................................................................................................................. 21

1.5.1 Status LED ........................................................................................................................ 21

1.5.2 Audio ................................................................................................................................. 21

1.5.3 Vibrator .............................................................................................................................21

1.6 Data Capture............................................................................................................................. 22

1.6.1 Dual-mode Support .......................................................................................................... 22

1.6.2 Symbologies Supported................................................................................................... 22

1.6.3 RFID Tags Supported ....................................................................................................... 24

8500 Series Mobile Computer Reference Manual

1.7 Communications via the Cradle...............................................................................................

1.7.1 Setting up the Cradle .......................................................................................................25

1.7.2 Cradle Options..................................................................................................................26

1.7.3 Understanding the Status Indicators ..............................................................................28

1.8 Communications Over Wireless Networks ..............................................................................29

1.8.1 IR/IrDA ..............................................................................................................................30

1.8.2 Bluetooth (Class 2)...........................................................................................................31

1.8.3 IEEE 802.11b/g ...............................................................................................................32

1.8.4 GSM/GPRS ....................................................................................................................... 33

LEARNING SOFTWARE ARCHITECTURE.............................................................................................35

2.1 Application Module...................................................................................................................37

2.1.1 Application Generator (AG) ..............................................................................................37

2.1.2 CipherNet.......................................................................................................................... 37

2.1.3 User Program.................................................................................................................... 38

2.2 System Configuration ............................................................................................................... 38

2.2.1 System Menu.................................................................................................................... 38

2.2.2 Kernel ...............................................................................................................................38

2.2.3 Program Manager ............................................................................................................38

SYSTEM MENU...................................................................................................................................39

3.1 Information................................................................................................................................40

3.1.1 Understanding Device Code ............................................................................................41

3.2 Settings .....................................................................................................................................42

3.2.1 Clock .................................................................................................................................42

3.2.2 Backlight Period ...............................................................................................................42

3.2.3 Auto Off .............................................................................................................................42

3.2.4 Power On Options............................................................................................................. 43

3.2.5 Key Click ...........................................................................................................................43

3.2.6 System Password .............................................................................................................43

3.2.7 Font ...................................................................................................................................43

3.2.8 Screen Calibration............................................................................................................ 43

3.2.9 Reset to Default ...............................................................................................................43

3.2.10 Reset Reader .................................................................................................................44

3.2.11 LCD Heater ..................................................................................................................... 44

3.3 Tests ..........................................................................................................................................45

3.3.1 Reader ..............................................................................................................................45

3.3.2 Buzzer ............................................................................................................................... 45

3.3.3 LCD & LED ........................................................................................................................45

3.3.4 Keyboard...........................................................................................................................45

3.3.5 Memory............................................................................................................................. 45

3.3.6 Touch Screen.................................................................................................................... 46

3.3.7 Vibrator .............................................................................................................................46

3.3.8 Echo Test .......................................................................................................................... 46

3.3.9 RFID ..................................................................................................................................46

3.4 Memory .....................................................................................................................................47

3.4.1 Size information ............................................................................................................... 47

3.4.2 Initialize............................................................................................................................. 47

3.5 Power......................................................................................................................................... 48

3.6 Load Program ...........................................................................................................................49

3.7 Bluetooth Menu ........................................................................................................................50

8500 Series Mobile Computer Reference Manual

3.7.1 Information .......................................................................................................................

3.7.2 Connect Setting................................................................................................................ 52

3.7.3 Security .............................................................................................................................53

3.7.4 Echo Tests ........................................................................................................................54

3.7.5 Pairing Test....................................................................................................................... 57

3.7.6 Freq. Dev. List................................................................................................................... 58

3.7.7 Network Setting................................................................................................................59

3.8 Serial PPP Menu .......................................................................................................................60

3.8.1 Information .......................................................................................................................60

3.8.2 Connection Set................................................................................................................. 61

3.8.3 Echo Test .......................................................................................................................... 62

3.9 IR Network Menu (Ethernet via IR) ..........................................................................................63

3.9.1 Information .......................................................................................................................63

3.9.2 Network Setting................................................................................................................64

3.9.3 Echo Tests ........................................................................................................................65

3.10 Wi-Fi Menu.............................................................................................................................. 66

3.10.1 Information.....................................................................................................................67

3.10.2 Network Setting .............................................................................................................68

3.10.3 WLAN Setting .................................................................................................................69

3.10.4 Security...........................................................................................................................70

3.10.5 Echo Tests ......................................................................................................................71

3.11 GSM/GPRS Menu................................................................................................................... 74

3.11.1 Information.....................................................................................................................74

3.11.2 Security...........................................................................................................................75

3.11.3 GPRS Setting.................................................................................................................. 76

3.11.4 GSM/GPRS Tests........................................................................................................... 77

PROGRAM MANAGER & KERNEL ...................................................................................................... 79

4.1 Program Manager.....................................................................................................................79

4.1.1 Download..........................................................................................................................80

4.1.2 Activate ............................................................................................................................. 82

4.1.3 Upload...............................................................................................................................83

4.2 Kernel........................................................................................................................................ 84

4.2.1 Kernel Information ...........................................................................................................84

4.2.2 Load Program ...................................................................................................................85

4.2.3 Kernel Update ..................................................................................................................87

4.2.4 Test & Calibrate................................................................................................................ 87

4.2.5 Bluetooth Menu................................................................................................................ 88

SPECIFICATIONS................................................................................................................................ 89

DOWNLOAD UTILITIES ....................................................................................................................... 91

ProgLoad.exe ................................................................................................................................... 92

IRLoad.exe .......................................................................................................................................93

Command Line ........................................................................................................................... 93

Download.exe .................................................................................................................................. 94

Command Line ........................................................................................................................... 94

TROUBLESHOOTING ..........................................................................................................................95

INTRODUCTION

Answering heavy industrial demands for robust, versatile and high performance computers, the 8500 Series Mobile Computer is specifically designed for all-day, everyday use as well as for data-intensive applications in harsh environments.

This line of product comes with built-in Bluetooth wireless technology and allows for optional modules for 802.11b/g as well as GSM/GPRS, enabling all the time, anywhere applications and seamless real time sharing of performance. The 8500 Series Mobile Computer is bundled with powerful and rich features to ensure success in timely processing of information, even in rigorous industrial environments, and thus, makes an ideal choice for a wireless solution in either increasing business flexibility or answering the demanding needs of heavy-duty mobile computers. Being programmable, this handy device can run custom applications or terminal emulation applications.

This manual serves to guide you through how to install, configure, and operate the mobile computer. We recommend you to keep one copy of the manual at hand for quick reference or maintenance purposes. To avoid any improper disposal or operation, please read the manual thoroughly before use.

Thank you for choosing CipherLab products!

8500 Series Mobile Computer Reference Manual

GETTING FAMILIARIZED WITH 8500

Figure 1: Overview

Introduction

INSTALLING THE HAND STRAP

The hand strap is ideal for one-handed operation, which requires safe and convenient hold of the mobile computer.

Warning: Always make sure the hand strap is well hooked and screwed to the back

of the mobile computer before use.

When the hand strap is desired, install it to the mobile computer by following these steps:

1) Place the mobile computer face down on a flat and clean surface.

2) Screw one end of the hand strap to the back of the mobile computer.

3) Insert and hook the other end of the hand strap to the bottom of the mobile

computer.

4) Make sure the hand strap is securely attached to the mobile computer.

5) Adjust the length of the hand strap to suit your handbreadth.

Figure 2: Installing the Hand Strap

8500 Series Mobile Computer Reference Manual

INSTALLING THE PISTOL GRIP

This contoured pistol grip enables intuitive trigger-and-scan operation, which is very helpful in scan intensive applications. When the pistol grip is desired, install it to the mobile computer by following these steps:

1) Place the mobile computer face down on a flat and clean surface.

2) Remove the shield-like cover on the back of the mobile computer by unscrewing.

If the hand strap is installed, remove it first. Keep the cover and screws for future use when the pistol grip is not desired.

3) Connect the power connector from the pistol grip to the receptacle on the mobile

computer.

4) Screw the pistol grip to the shield-like cover.

5) Make sure all screws are tightened up.

6) Turn on the mobile computer and test the trigger.

Figure 3: Installing the Pistol Grip

Introduction

CHARGING THE BATTERY

You can use a cradle or charger to charge the Mobile Computer and/or its battery. Below is the 4-Slot Battery Charger. For the Charging & Communication Cradle, refer to section

Communications via the Cradle.

1.7

Warning: It is recommended that the charging devices be operated at room

temperature (18°C to 25°C) for optimal performance. The charging devices will not charge the battery when the temperature exceeds 40°C.

1) The Battery Charger can be mounted on table or wall. Drill two holes (centers spaced

160 millimeters apart), secure the two supplied screws, and mount the Battery Charger by sliding over screws.

2) Slide the battery into the battery compartment at a proper angle, with contacts facing

to back.

3) Connect the power supply cord to the power receptacle on the charger.

4) Connect the other end of the power supply cord to a suitable power outlet.

5) Press the power switch on, and the Battery Charger’s LED will be red.

6) While charging, the LED of the battery compartment will be red. When fully charged,

the LED will be green.

Figure 4: 4-Slot Battery Charger

LED Status Meaning

Power Solid red

Off

Power ON

Power OFF

Battery Charging Solid red

Solid green

Flashing red and green

Off

Charging battery

Charging done

Error occurs

Battery not ready

8500 Series Mobile Computer Reference Manual

DIMENSIONS

Figure 5: Dimensions

Introduction

FEATURES

 Ergonomic design — ruggedized yet streamlined, with hand strap for secure hold.  Built tough to survive drop test and sealed against moisture/dust to IP 64.  Upgradeable memory — optional memory card adds up to 10 MB (2 MB onboard + 8

MB) for data storage.

 Dual mode support — One barcode scan engine plus the RFID reader  Total wireless solution — IR/IrDA and Bluetooth integrated, with connectivity options

for 802.11b/g and/or GSM/GPRS.

 Large graphic monochrome LCD touch screen supports double-byte characters and

bitmap graphics. The touch screen featuring signature capture can be activated with its stylus or a finger, software programmable.

 Programmable feedback includes buzzer, LED indicator, and vibrator.  Quick link to any backend database through Windows-based CipherNet programs for

VT100/220 and IBM 5250 emulation.

 Easy customization of AG applications through Windows-based Application Generator

(AG) programs for preloaded AG Runtime.

 Programming support includes BASIC & C compilers.  Accessories and peripherals include pistol grip, international AC charging cradle, etc.

INSIDE THE PACKAGE

The following items are included in the package. Save the box and packaging material for future use in case you need to store or ship the mobile computer.

 8500 Series Mobile Computer  Rechargeable Li-ion battery pack  Stylus  Hand Strap  Software & Manual CD

Note: For battery charging, you need to purchase a charging cradle separately.

8500 Series Mobile Computer Reference Manual

ACCESSORIES

Rich choices of optional accessories are available for you to enhance the total performance of the mobile computer.

 Pistol Grip (detachable)  Belt Holster  Protective Cover  Memory Card, 4 or 8 MB  Spare rechargeable Li-ion battery  4-slot Battery Charger  Charging & Communication Cradle  Modem Cradle  Ethernet Cradle  Vehicle Cradle  Travel Charger  Bluetooth Access Point  802.11b/g Access Point

Chapter 1

USING 8500 MOBILE COMPUTER

This chapter explains the features and usage of the 8500 Series Mobile Computer. The 8500 family includes:

 8500 Bluetooth Class 2  8570 Bluetooth Class 2 + 802.11b/g  8580 Bluetooth Class 2 + GSM/GPRS  8590 Bluetooth Class 2 + 802.11b/g + GSM/GPRS

IN THIS CHAPTER

1.1 Battery....................................................................... 9

1.2 Memory.................................................................... 12

1.3 Keypad..................................................................... 13

1.4 Touch Screen ............................................................ 19

1.5 Notifications.............................................................. 21

1.6 Data Capture ............................................................ 22

1.7 Communications via the Cradle.................................... 25

1.8 Communications over Wireless Networks....................... 29

1.1 BATTERY

 Main Battery

The mobile computer is powered by a rechargeable 3.7 V/4000 mAh Li-ion battery pack, and it takes approximately four hours to fully charge it.

For power-saving purpose, always turn off the backlight while working in a well-lit area. When the backlight is on for extended periods of time, the main battery will become low sooner than expected.

The smart battery icon on the LCD screen shows the status of power consumption. There are two ways to monitor a low battery charge or discharged battery from the screen.

 Examine the level of the 4-bar battery icon  Monitor voltage level (see section 3.5 Power)

 Backup Battery

The backup battery on the main board takes charge when the main battery is removed or drained out. When fully charged, the 3.0 V/7 mAh rechargeable Lithium button cell helps retain data in SRAM and maintain the running of the real-time clock and calendar for at least one week without the main battery. In the meantime, you have to replace the main battery as soon as possible.

It takes at least twenty-four hours to fully charge the backup battery. However, it is not necessary to fully charge the backup battery for the mobile computer to work.

8500 Series Mobile Computer Reference Manual

 Monitor voltage level (see section 3.5 Power)

1.1.1 INSERTING THE BATTERY

For shipping and storage purposes, save the mobile computer and the main battery in separate packages. This will keep both batteries in good condition for future use.

Note: Any improper handling may reduce the battery life.

1) Hold the mobile computer still as shown below.

2) Slide the battery pack into the battery compartment at a proper angle (30°~45°) so

that the tabs on the bottom of the battery are hooked in the grooves of the compartment. Make sure that the battery is snugly fit into the compartment.

3) Slide the battery latch to lock the battery in the compartment.

Note: For a new battery, make sure it is fully charged before use. Always prepare a

spare battery pack, especially when you are on the road.

Figure 6: Installing the Main Battery

Chapter 1 Using 8500 Mobile Computer

1.1.2 CHARGING THE BATTERY

The main and backup batteries may not be charged to full for shipment. When you first receive the package, you will need to charge batteries to full before using the mobile computer.

Note: For initial charging, it takes approximately 4 hours to fully charge the main

battery.

Because the internal backup battery is constantly charged from the main battery, the initial charging requires inserting the battery pack to the mobile computer and then seating the mobile computer in the cradle for charging. This will have both the main and backup batteries charged at the same time.

Note: For a new battery, make sure it is fully charged before use. Always prepare a

spare battery pack, especially when you are on the road.

1.1.3 CAUTION OF LOW BATTERY CHARGE

The battery pack is the only power source for the mobile computer to work. It also charges the backup battery on the main board so that the data stored in SRAM can be retained properly. Therefore, when the main battery charge goes low, you need to replace the battery pack with a charged one or charge it as soon as possible. Most of all, always save data before it is too late; you should upload important data on a regular basis.

Warning: Data loss may occur with SRAM during low battery condition. Always save

data before running out of power or keep a fresh battery for replacement.

1.1.4 POWER MANAGEMENT

For any portable device, power management is a critical issue especially when you are on the road. Below are some tips to help you save battery power.

Warning: Using backlight, wireless connectivity, and peripherals while on battery

power will substantially reduce battery power.

 To speed up charging the mobile computer, turn off the mobile computer and seat it

in the cradle.

 Bring a second battery pack on the road.  Stop wireless connectivity, Bluetooth, 802.11b/g or GSM/GPRS that is not in use.

8500 Series Mobile Computer Reference Manual

1.2 MEMORY

The collected data can be sent back to a host computer immediately over wireless networks, or stored in memory (SRAM) and upload later. The mobile computer is equipped with a calendar chip for accurate time/date logging.

 Read-only Memory (ROM)

2 megabytes flash memory for storing core, OS, application programs, fonts, etc.

 Random-access Memory (RAM)

2 megabytes SRAM for storing data. Its contents will be retained by the backup battery.

1.2.1 CAUTION OF DATA LOSS

When the main battery is removed or drained, the backup battery on the main board is to retain the contents of SRAM and maintain the running of real-time clock and calendar for at least one week, on condition that the backup battery has already been fully charged.

If you want to put away the mobile computer for a couple of days, you should be aware that data loss occurs when both the main and backup batteries discharge completely. Therefore, it is necessary to upload data and files before putting away the mobile computer!

1.2.2 UPGRADEABLE MEMORY

When ordering, you may choose to have up to 10 MB memory — 2 MB onboard + 8 MB memory card.

 4 MB memory card  8 MB memory card

Chapter 1 Using 8500 Mobile Computer

1.3 KEYPAD

The mobile computer can be equipped with a keypad of 24 keys or 44 keys for system setup, user entry and so on. The keypad comes with programmable LED backlight, like the screen. Refer to section

Silicon rubber has been chosen for their durability and prompt feedback. The key click

can be configured through programming or the System Menu.

Below briefly describes the functions of common keys on the mobile computer.

SCAN

It will trigger the scan engine to read a barcode, or the RFID reader to read a tag, if the COM port is enabled.

ENTER

Two on each side of the [SCAN] trigger, user-friendly and convenient for either right-handed or left-handed operator to perform general function of the [ENTER] key.

Normally, the [ENTER] key is used for command execution or input confirmation.

1.4 LCD for screen & backlight settings.

ESC (Escape)

Normally, this key is used to stop and exit the current operation.

BkSp (Backspace)

If this key is being held down for more than one second, a clear code will be sent.

FN (Function)

This key serves as a modifier key and has to be used together with another key. For example, press [FN] + [1] can produce the result of F1.

POWER

In order to prevent an accidental press of the POWER key, you need to hold down this key for approximately 1.5 seconds to turn ON/OFF the mobile computer.

Note: Functionality of keys is application-dependent.

8500 Series Mobile Computer Reference Manual

1.3.1 SCREEN ICONS

When any of the following icons appears on the screen, it indicates a certain mode is activated. It means holding down the specific key is unnecessary.

24-key

A This icon appears when you press [Alpha] once, indicating it is set to alphabetic

a This icon appears when you press [Alpha] twice, indicating it is set to alphabetic

Description

mode for typing capital letters.

mode for typing small letters.

This icon appears when you press [FN], indicating it is set to the function mode. Then, press another key ([1] ~ [9]) to produce the result and the icon will go off.

 To get the value of another key combination modified by the [FN] key, repeat

the above steps.

 To exit the function mode, press [FN] again and the icon will go off.

44-key Description

This icon appears when you press [Shift] to set the alphabetic mode to small letters.

 By default, the alphabetic mode is set to capital letters.

This icon appears when you press [RED], indicating it is set to the function mode. Then, press another key ([F1] ~ [F12]) to produce the result and the icon will go off.

 To get the value of another key combination modified by the [RED] key, repeat

the above steps.

 To exit the function mode, press [RED] again and the icon will go off.

This icon appears when you press [Alt] to enter the special function mode.

Note: When using the Function, Shift or Alt key to modify another key, the system will

send the associated key code to the application program, and it is up to the application program to interpret the key code.

Chapter 1 Using 8500 Mobile Computer

1.3.2 24-KEY LAYOUT

The layout of the 24-key keypad is similar to that of a telephone, which consists of an alphanumeric keypad, navigation and function keys, as well as assorted characters.

Figure 7: 24-key Layout

8500 Series Mobile Computer Reference Manual

This alphanumeric keypad is set to numeric mode by default. The [Alpha] key serves as a toggle among numeric, alpha (lower-case alphabetic), and ALPHA (upper-case alphabetic) input modes.

Note: It is not necessary to hold down the [Alpha] key.

The alpha icon will appear on the lower-left corner of the screen in a sequence as shown below.

Status Icon Alpha Key Input Mode

(none) N/A Numbers

a Press the [Alpha] key one time Small letters

A Press the [Alpha] key two times Capital letters

When in alpha mode, it takes turns to show alphabets and number when you keep pressing the same key; each press must not exceed one second. For example, keep pressing the number key [2], it will take turns to show “A”, “B”, “C” or “2”.

 When you first press the number key [2], it will product the letter “A” or “a”.  When you press the number key [2] twice (the time interval must not exceed one

second), it will produce the letter “B” or “b”.

 When you press the number key [2] three times (the time interval between each

press must not exceed one second), it will produce the letter “C” or “c”.

 When you press the number key [2] four times (the time interval between each press

must not exceed one second), it will produce the number “2”.

In order to get the desired character, you will need to press the same key, one to four times (the time interval between each press must not exceed one second). Only when you stop pressing the same key for longer than one second or you press another key, will the system send the real key code to the application program.

Chapter 1 Using 8500 Mobile Computer

1.3.3 44-KEY KEYPAD

The layout of the 44-key keypad includes numeric, alphabetic, assorted characters, function and modifier keys.

Figure 8: 44-key Layout

8500 Series Mobile Computer Reference Manual

For the 44-key keypad, these keys can be categorized into the following groups by color:

Blue Area

 Two [ENTER] keys: user-friendly and convenient for either right-handed or left-handed

operator to perform general function of a [Enter] key.

 It can be used together with [RED] modifier key: [ENTER] + [RED] = alternately turn ON/OFF

the backlight of LCD and keypad.

Black Area

 [POWER] key  Numeric keys  Modifier keys: [Shift] or [Alt] that modifies its next key. The functionality depends on software

application.

 Others like [Backspace], [ESC], [Space], [Tab], [Insert], [Delete], [ - ], [ . ]

Yellow Area

 [SCAN] trigger  Navigation keys for moving the cursor up, down, left, right.  Alphabetic keys  Others like punctuation keys for comma & semi-colon, dollar & colon.

Red Area

 [RED] modifier key: the solid red key next to the Power key  [RED] followed by one red-coded key: The [RED] modifier key modifies (activates) the second

key. Its functionality is determined by the red-coded key, which is specified by red letters under the navigation keys or on top of alpha keys and some punctuation keys.

Chapter 1 Using 8500 Mobile Computer

1.4 LCD

The mobile computer comes with a 3” FSTN graphic LCD, 160 by 160 pixels resolutions, which can be programmed to display text or graphics, such as specific font and company logo, to meet varying application needs.

Options

English font

Chinese font Other language fonts,

Font Size (pixels) Characters by lines

Font size 6×8 (pixels)

Font size 8×16 (pixels)

Font size 16×16 (pixels) 10 characters by 9 lines

Programmable

26 characters by 19 lines

20 characters by 9 lines

company logo…

Note: Normally, the bottom line (ICON_ZONE) is reserved to display status icons, such

as the battery icon.

1.4.1 ADJUSTING THE BACKLIGHT

The backlight of screen and keypad helps ease reading under dim environments. It can be turned on and adjusted decreasingly or increasingly by the following key combinations. Keep pressing the key combination until the luminosity or contrast is decreased or increased to a desired level.

Warning: Using backlight while on battery power will substantially reduce battery

power. It is suggested to dim the backlight while working in a well-lit area or automatically turn it off when not in use.

Key Combination Action

24-key 44-key

[FN] + [Enter] [RED] + [Enter] Toggle ON/OFF the backlight

[FN] + [Left] [RED] + [Left] Turn ON the backlight of LCD and decrease its luminosity

[FN] + [Right] [RED] + [Right] Turn ON the backlight of LCD and increase its luminosity

[FN] + [Up] [RED] + [Up] Turn ON the backlight of LCD and increase its contrast

[FN] + [Down] [RED] + [Down] Turn ON the backlight of LCD and decrease its contrast

Note: Hold down the [FN] key and press the second key for adjustment.

8500 Series Mobile Computer Reference Manual

1.4.2 CALIBRATING THE SCREEN

This LCD is also a touch screen, which enables the use of a stylus for handwriting. It also features signature capture that can save signature as confirmation of receipt when delivering goods to door.

Refer to section 3.2 Settings for screen & contrast calibration.

Warning: DO NOT use any pointed or sharp objects to move against the surface of

the screen.

Chapter 1 Using 8500 Mobile Computer

1.5 NOTIFICATIONS

1.5.1 STATUS LED

The dual-color LED above the [SCAN] trigger is used to provide information on the charging status and can be programmed to provide information that helps diagnosing.

For example, if you are using AG Runtime, you will be informed of the scanning result

immediately. The green LED is used for "Good Read" while collecting data.

Tasks Green LED Red LED

Charging 8500 --- On

Charging done On ---

Good Read On ---

Error occurs --- On

1.5.2 AUDIO

The mobile computer has a low power transducer type buzzer. It can be programmed for status feedback. Its frequency and duration are software programmable.

1.5.3 VIBRATOR

The mobile computer is integrated with a vibrator, which is software programmable for feedback. This can be helpful when working in noisy environments.

8500 Series Mobile Computer Reference Manual

1.6 DATA CAPTURE

A wide variety of scan engines is available for delivering flexibility to meet different requirements.

 1D CCD scan engine  1D Laser scan engine  1D Long Range Laser scan engine  1D Extra Long Range Laser scan engine  2D scan engine  RFID reader

Varying by the scan engine installed, the supported symbologies or tag types are listed below.

Note: Instead of running the preloaded AG runtime or terminal emulation program, you

can develop your own applications to control the scan engine for data collection.

1.6.1 DUAL-MODE SUPPORT

Options of different scan engine combination are allowed, such as 1D+RFID and 2D+RFID. For each combination, both readers can be initialized and ready for scanning at the same time (dual mode operation). For example, if you press the [SCAN] trigger while running the preloaded AG runtime on the mobile computer, it will read a barcode in position or an RFID tag in proximity depending on which one comes first.

Note: The mobile computer allows the co-existence of one integrated scan engine and

the RFID reader. However, you cannot have 1D+2D scan engines installed on the mobile computer because they are both barcode readers!

1.6.2 SYMBOLOGIES SUPPORTED

Depending on the scan engine integrated, the mobile computer is capable of scanning barcodes of a number of symbologies that are enabled by default while running the preloaded AG runtime. Refer to section

If you need to scan barcodes that are encoded in a symbology that is disabled by default,

Application Generator (AG*.exe) allows configuring symbology settings, as well as

reader settings. First, enable the desired symbologies, and then, download application to the mobile computer.

3.3.1 Reader for functional test.

Note: For details on configuring reader and symbology settings, please refer to the

documentation of the software you use.

Chapter 1 Using 8500 Mobile Computer

Symbologies Supported: Enable/Disable CCD, Laser LR, ELR 2D

Codabar Enabled Enabled Enabled Code 11 Not supported Code 93 Enabled Enabled Enabled Composite

Code

MSI Disabled Enabled Enabled Plessey Disabled Not supported Not supported

Postal Codes Not supported Telepen Disabled Not supported Not supported Code 128

Code 2 of 5

Code 3 of 9

CC-A/B Not supported Not supported Disabled

CC-C Not supported Not supported Disabled

TCIF Linked Code 39 Not supported

Code 128 Enabled Enabled Enabled

EAN-128 Enabled Enabled Enabled

ISBT-128 Disabled Disabled Disabled

Industrial 25 (i.e. Discrete 25) Enabled Enabled Enabled

Interleaved 25 Enabled Enabled Enabled

Matrix 25 Disabled Not supported Not supported

Code 39 Enabled Enabled Enabled

Trioptic Code 39 Not supported Disabled Disabled

Not supported Enabled

Italian Pharmacode (i.e. Code

32)

French Pharmacode Disabled Not supported Not supported

EAN/UPC

RSS RSS-14 Disabled Enabled Enabled

RSS Limited Disabled Enabled Enabled

EAN-8 Enabled Enabled Enabled

EAN-8 Addon 2 Disabled Enabled Enabled

EAN-8 Addon 5 Disabled Enabled Enabled

EAN-13 Enabled Enabled Enabled

EAN-13 & UPC-A Addon 2 Disabled Enabled Enabled

EAN-13 & UPC-A Addon 5 Disabled Enabled Enabled

Bookland EAN (i.e. ISBN) Disabled Disabled Disabled

UPC-E0 Enabled Enabled Enabled

UPC-E1 Disabled Disabled Disabled

UPC-E Addon 2 Disabled Enabled Enabled

UPC-E Addon 5 Disabled Enabled Enabled

UPC-A Enabled Enabled Enabled

Disabled Disabled Disabled

8500 Series Mobile Computer Reference Manual

RSS Expanded Disabled Enabled Enabled

Symbologies

PDF417 Not supported

MicroPDF417 Not supported

Not supported Enabled 2D

Not supported Enabled

Data Matrix Not supported Not supported Enabled

Maxicode Not supported Not supported Enabled

QR Code Not supported Not supported Enabled

1.6.3 RFID TAGS SUPPORTED

The RFID reader supports read/write operations depending on the tags. The supported labels include ISO 15693, Icode®, ISO 14443A, and ISO 14443B.

Currently, the performance of many tags has been confirmed, and the results are listed below for your reference. Refer to section

Note: You should study the specifications of RFID tags before use.

RFID Module Version 1.0 UID Only Read Page Write Page

ISO 14443A Mifare Standard 1K

Mifare Standard 4K

Mifare Ultralight

Mifare DESFire

Mifare S50

SLE44R35

SLE66R35 ISO 14443B SRIX 4K

SR176 ISO 15693 ICODE SLI

SRF55V02P

SRF55V02S

SRF55V10P

TI Tag-it HF-I

ICODE®

ICODE

(Phillips)

3.3.9 RFID for functional test.

9 9 9

--- ---

Chapter 1 Using 8500 Mobile Computer

1.7 COMMUNICATIONS VIA THE CRADLE

1.7.1 SETTING UP THE CRADLE

The cradle is designed for charging and communications at the same time. You may choose a cradle type that best suits your needs.

1) Place the cradle on a flat and clean surface.

2) Connect the power supply cord to the power jack on the back of the cradle, and then

connect the other end of the power supply cord to a suitable power outlet. The cradle is ready for charging the mobile computer, as well as the spare battery pack.

3) Seat the mobile computer in the cradle.

If data communications are desired at the same time, you can establish a proper connection with a computer or remote host. Refer to the Installation Guide of your cradle.

Figure 9: Setting up cradle

8500 Series Mobile Computer Reference Manual

1.7.2 CRADLE OPTIONS

The following cradle types are available on order —

Cradle Type

POWER Jack

RS-232 Port

Line Jack

Phone Jack

RJ-45 Port

DIP Switch

IP Reset Switch

Note: (1) Modem Cradle — Delivering flexibility in making a connection, the Modem

Cradle integrates the modem functionality (56 kbps) into the cradle. You may choose to use the modem or RS-232 port by sliding the DIP switch. (2) Ethernet Cradle — Refer to the Ethernet Cradle manual for more information.

Charging & Comm. Cradle Modem Cradle Ethernet Cradle

√ √ √

− √ −

−

− √ √ (RS-232/Modem) √ (Auto/LAN)

− √

Figure 10: Cradle Options

Chapter 1 Using 8500 Mobile Computer

 Modem Cradle: DIP Switch

Modem Connection

 To use the modem functionality, slide the DIP switch to right:  When the power cable is properly connected, the LED light of POWER on the front panel

will be solid red.

RS-232 Connection

 To use the RS-232 port, slide the DIP switch to left:  When the power cable is properly connected, the LED light of POWER on the front panel

will be solid green.

 Ethernet Cradle: DIP Switch

Auto-detect Connection

Slide the DIP switch to left:

 The RS-232 connection will override

However, you can use cradle commands to switch in between the two.

Ethernet connection when both are present.

 When the power cable is properly connected, the LED light of POWER on the front panel

will be solid green.

LAN Connection

Slide the DIP switch to right:

 Only the Ethernet connection can be established. However, you can use cradle commands

to switch in between the two.

 When the power cable is properly connected, the LED light of POWER on the front panel

will be solid red.

8500 Series Mobile Computer Reference Manual

1.7.3 UNDERSTANDING THE STATUS INDICATORS

For charging status of the loaded battery in the mobile computer, view the device screen.

Figure 11: Cradle LEDs

Front Panel LEDs

POWER:

Tasks

Spare battery charging status

status

Line status

Indication of connection status

Solid red Charging

Solid green Charging done

Flashing (red/green) Error occurs

Off Battery not ready Solid red Receiving data from Ethernet or host RX: Receiving

Off No activity Solid red Transmitting data to Ethernet or host TX: Transmitting

Off No activity

Solid red Modem/Ethernet connection

Solid green Direct connection via RS-232

Off Power off

Warning: Charging error may occur due to a power failure or defected battery

contacts.

Chapter 1 Using 8500 Mobile Computer

1.8 COMMUNICATIONS OVER WIRELESS NETWORKS

The 8500 Series Mobile Computer supports state-of-the-art wireless technologies so that it can send/receive data in real time in an efficient way.

 WPAN: Infrared (IR/IrDA) technology for data exchange, embedded  WPAN: Bluetooth technology for cable replacement & data exchange, embedded  WLAN: IEEE 802.11b/g for wireless networking, optional  WWAN: GSM/GPRS for short message service, optional

Generally, the coverage of each technology can be viewed as follows.

Figure 12: Coverage of Wireless Technologies

8500 Series Mobile Computer Reference Manual

1.8.1 IR/IrDA

The mobile computer has an integrated IR port on the bottom, which can directly establish connection with an IR device for printing or data exchange. Simply have the IR port of the mobile computer toward the IR port of the target device.

 This IR port supports CipherLab proprietary IR communication protocol and standard

IrDA protocol.

 IrDA specification defines communications (transmit/receive data) between two IrDA

enabled devices within a short range, line-of-sight.

IR/IrDA Specifications

Infra Red Optical Data Rate Up to 115200 bps Connected Devices Peer-to-Peer Coverage From contact to 30 cm, line-of-sight Standard CipherLab proprietary protocol and IrDA 1.0

Chapter 1 Using 8500 Mobile Computer

1.8.2 BLUETOOTH (CLASS 2)

Bluetooth technology is for cable replacement & data exchange. With built-in Bluetooth module, the mobile computer can directly communicate with any Bluetooth enabled device, not necessarily line-of-sight.

 Serial Port Profile (SPP) is for ad-hoc networking, without going through any access

point.

 Dial-Up Networking Profile (DUN) makes use of a Bluetooth modem or mobile phone

as a wireless modem.

Also, it can be used to activate the GPRS functionality on a mobile phone.

 Human Interface Device Profile (HID) allows the mobile computer to work as an input

device, i.e. keyboard, for a host computer.

 Personal Area Networking Profile (PAN) makes use of Bluetooth Network

Encapsulation Protocol (BNEP) for IP networking over Bluetooth. Access points (AP) are required.

Bluetooth Specification

Frequency Range 2.4 GHz Data Rate 433 kbps Connected Devices 1 for DUN mode

Up to 7 for SPP or PAN mode (AP required)

Profiles SPP, DUN, HID, PAN Coverage Class 2 — 10 meters line-of-sight Max. Output Power Class 2 — 6 mW Spread Spectrum FHSS Modulation GFSK Standard Bluetooth version 1.1

8500 Series Mobile Computer Reference Manual

1.8.3 IEEE 802.11b/g

The 8570/8590 mobile computer can easily connect to legacy networks through access points (APs). Roaming among different networks is possible.

IEEE 802.11b/g is an industrial standard for Wireless Local Area Networking (WLAN), which enables wireless communications over a long distance. The speed of connection between two wireless devices will vary with range and signal quality. To maintain a reliable connection, the data rate of the 802.11b/g system will automatically fallback as range increases or signal quality decreases.

802.11b/g Specification

Frequency Range 2.4 GHz Data Rate: 802.11b – 1, 2, 5.5, 11 Mbps

802.11g – 6, 9, 12, 18, 24, 36, 48, 54 Mbps

Connected Devices 1 for ad-hoc mode (No AP)

Multiple for infrastructure mode (AP required)

Profiles IP/TCP/UDP Coverage 350 meters line-of-sight Max. Output Power 50 mW (802.11b) Spread Spectrum DSSS Modulation 802.11b — DBPSK (1 Mbps), DQPSK (2 Mbps), CCK (5.5 & 11

Mbps)

802.11g — OFDM

Standard IEEE 802.11b/g, interoperable with Wi-Fi devices

Chapter 1 Using 8500 Mobile Computer

1.8.4 GSM/GPRS

The 8580/8590 mobile computer is capable of data communications over free air, right on the road.

 GSM and GPRS are industrial standards for Wireless Wide Area Networking (WWAN),

which enables wireless communications over free air.

 “GSM” is an abbreviation of Global System for Mobile Communications.  “GPRS” is an abbreviation of General Packet Radio Service.  GPRS, a packet-switched technology based on GSM (circuit-switched), allowing

information to be transmitted or received more quickly, immediately and efficiently across the mobile network. GPRS Class B mobile devices can be attached to both GSM and GPRS services, using one service at a time.

Take the following steps to insert your SIM card when GSM/GPRS networking is desired —

1) Turn off the mobile computer.

2) Hold the mobile computer still and unscrew the four screws of the top enclosure.

3) Take out the GSM/GPRS card from the mobile computer.

4) Check the card orientation and insert the SIM card to the SIM card holder on the

GSM/GPRS card.

5) Put the GSM/GPRS card back to the mobile computer.

6) Screw the top enclosure tightly.

Figure 13: Inserting the SIM Card

8500 Series Mobile Computer Reference Manual

Chapter 2

LEARNING SOFTWARE ARCHITECTURE

This chapter mainly describes the software inside the mobile computer. It consists of three modules — Kernel, System, and Application; each has a function menu.

When a menu is displayed, you may select an item by either of the following ways:

 using the [UP] and [DOWN] keys to move the highlight bar  pressing the number key that corresponds to the item number  using the stylus to touch that item or the item number

8500 Series Mobile Computer Reference Manual

On each screen, the bottom line displays status icons, such as:

 The 4-bar battery icon indicates the current power status.  The input mode or function mode, which is controlled by the [Alpha] key and [FN] key

separately.

 When a turn-page icon ( ) is displayed, it indicates there is a previous page or

menu.

To return to a previous page or menu, you may press [ESC], touch the menu title, or follow the on-screen instructions.

Figure 14: Software Architecture

IN THIS CHAPTER

2.1 Application Module..................................................... 37

2.2 System Configuration ................................................. 38

Chapter 2 Learning Software Architecture

2.1 APPLICATION MODULE

For easy development of applications, the mobile computer ships with development tools

on the CD-ROM. It includes Windows-based programs Application Generator (batch and WLAN), CipherNet (VT and 5250), download utilities, etc.

2.1.1 APPLICATION GENERATOR (AG)

The mobile computer is preloaded with AG Runtime. When you turn on the mobile

computer, it displays the Main Menu of AG application, as shown below.

Batch AG

Before using the mobile computer to collect data, you need to configure the application with the companion tool on your computer. This time-saving development tool helps create application templates on your computer.

For details on the AG application, please refer to separate user manual.

Application Generator

Batch AG U8500*.SHX AG8500.exe RF AG U85WLAN*.SHX AG8500WLAN.exe

Note: The Application Generator (AG) software package includes

(1) a companion tool for quickly developing your application, i.e. AG or RF AG; (2) several download utilities to make it versatile in use.

AG Runtime Companion Tool on PC End

RF AG

2.1.2 CIPHERNET

The mobile computer supports VT100/220 and IBM 5250 terminal emulation for

accessing a backend database. Instead of using Application Generator, you may download the terminal emulation program, i.e. CipherNet Runtime, to the mobile

computer. Refer to section 3.6 your computer.

For details on the CipherNet application, please refer to separate user manual.

Load Program. Then, run individual companion tool on

8500 Series Mobile Computer Reference Manual

Terminal Emulation CipherNet Runtime Companion Tool on PC End

VT100/220 85xx-VT.SHX CipherNet-VT.exe IBM 5250 85xx-5250.SHX CipherNet-5250.exe

2.1.3 USER PROGRAM

You may need to develop your own application program. For developing custom applications, CipherLab provides BASIC and C compliers through licensing. For detailed information, please contact your sales representative.

2.2 SYSTEM CONFIGURATION

For managing system configurations and multiple programs, each mobile computer

comes with the System Menu, Kernel, and Program Manager. Refer to the following

chapters on how to configure the 8500 Series Mobile Computer, regarding system configurations and program download.

2.2.1 SYSTEM MENU

The System Menu is bundled with BASIC Runtime or user programs that are written in “C”. It is for system configuration, functionality testing, downloading font file and program.

2.2.2 KERNEL

Kernel is the innermost core of the OS. It provides services for downloading the active

application program or font file, updating the kernel or the active application program, and configuring Bluetooth settings.

2.2.3 PROGRAM MANAGER

The Program Manager is part of the kernel. You may download as many as seven application programs, or six programs plus one font file.

Chapter 3

SYSTEM MENU

The System Menu is generated by a powerful utility, which offers an interface for

engineers (programmers or system integrator) to view system information, change the configuration parameters, download programs and run diagnostics.

This menu is designed for engineering tests and maintenance ONLY. For this reason, the

System Menu provides password protection to prevent unauthorized users from

accidentally changing system settings.

Warning! The System Menu is NOT for the use of any end users. The system

password helps ensure system safety and integrity.

How to access the System Menu?

1) Turn off the mobile computer.

2) Press [7] + [9] + [Power].

IN THIS CHAPTER

3.1 Information............................................................... 40

3.2 Settings ................................................................... 42

3.3 Tests ....................................................................... 45

3.4 Memory.................................................................... 47

3.5 Power ...................................................................... 48

3.6 Load Program............................................................ 49

3.7 Bluetooth Menu ......................................................... 50

3.8 Serial PPP Menu......................................................... 60

3.9 IR Network Menu ....................................................... 63

3.10 Wi-Fi Menu.............................................................. 66

3.11 GSM/GPRS Menu...................................................... 74

8500 Series Mobile Computer Reference Manual

3.1 INFORMATION

Here provides important system information to help diagnose the system.

System Menu > 1. Information

H/W Hardware version (PCB) S/N A serial number assigned to the mobile computer M/D Manufacturing date KNL Kernel version LIB BSC USR Application program version DEV 5-digit code for optional hardware configurations

C library version

BASIC Run-time version, if a BASIC application is downloaded

 For example, 1710-1 indicates the 44-key mobile computer is equipped with

CCD scan engine, RFID reader, and 802.11b/g and GSM/GPRS connectivity.

RFID RFID module version if present; the 3

digit of the above Device Code must be 1

Chapter 3 System Menu

3.1.1 UNDERSTANDING DEVICE CODE

Device Code Modular Component Types

1st digit Reader module 0= none

1= CCD scan engine

2= Laser scan engine

3= 2D scan engine

4= Long Range Laser scan engine

5= Extra Long Range Laser scan engine

2nd digit Wireless module 3= Bluetooth + GSM/GPRS

4= Bluetooth + 802.11b/g

5= Bluetooth only

7= Bluetooth + GSM/GPRS + 802.11b/g

3rd digit RFID module 0= none

1= RFID reader

4th digit Reserved 0

5th digit Keypad module 0= 24-key

1= 44-key

(8580)

(8570)

(8500)

(8590)

8500 Series Mobile Computer Reference Manual

3.2 SETTINGS

You can change the default settings here.

System Settings

Clock blank Backlight Period 20 seconds, Level 2 Auto Off 10 minutes Power On Options Program Resume Key Click Tone 2 System Password Open access Font System font Reset to Default Load factory settings Reset Reader Load factory settings of 2D or (Extra) Long Range Laser scan engine LCD Heater Disabled

Default Values

3.2.1 CLOCK

Set date and time for Real Time Clock. Enter two digits for the year, i.e. 04 for 2004.

3.2.2 BACKLIGHT PERIOD

Set the backlight duration for the keypad and LCD.

 Enter a value between 0 and 9999 (second).  Use the [UP] and [DOWN] keys to adjust the backlight level.

3.2.3 AUTO OFF

The mobile computer will be turned off automatically when no operation is taking place during a specified period of time. Enter a value between 0 and 999 (minute).

Note: To disable this function, enter 0.

Chapter 3 System Menu

3.2.4 POWER ON OPTIONS

Set the startup screen once the mobile computer is turned on:

 When “[0] Program Resume” is selected, the mobile computer will start from the last

session of program before it is turned off.

 When “[1] Program Restart” is selected, the mobile computer will start from the first

session of the program.

3.2.5 KEY CLICK

The system will produce an audible signal when any key on the keypad is pressed. The current value is highlighted. Select a desired tone for the buzzer or mute it.

3.2.6 SYSTEM PASSWORD

Set a password to control user access to the System Menu. The password can be up to

eight alphanumeric characters.

Note: The password is case-sensitive. To disable a previous password, enter blank on

the "Input new password" and "Verify password" screens.

3.2.7 FONT

Font version information can be viewed here. It displays System Font if there is no custom font file.

If a multi-language font file is downloaded, you will be able to select a font from the list.

3.2.8 SCREEN CALIBRATION

The cross mark will appear on the four corners of the screen for alignment. Use the tip of the stylus to tap at the center of the cross mark firmly and accurately.

To start with contrast calibration, press [1]+[9] simultaneously. Refer to section for screen & backlight settings.

Warning: DO NOT use any pointed or sharp object to move against the screen.

1.4 LCD

3.2.9 RESET TO DEFAULT

Reset system settings to the default values, except for the reader settings.

8500 Series Mobile Computer Reference Manual

3.2.10 RESET READER

You may reset the reader settings to the default values when one of the following scan engines is installed for use:

 2D scan engine  Long Range Laser scan engine  Extra Long Range Laser scan engine

3.2.11 LCD HEATER

Set the heater functionality. When enabled, it will start to heat when the environmental temperature falls below -10 Celsius degrees.

Chapter 3 System Menu

3.3 TESTS

Here provides functional tests for key parts.

3.3.1 READER

The supported symbologies depend on the scan engine you use. Refer to section 1.6

Data Capture for symbologies that are enabled by default. For symbologies that are

disabled by default, they must be enabled through programming.

 Test the reading performance of the scanner. Press [SCAN] to start.  To stop and exit the test, press any key.

3.3.2 BUZZER

Test the buzzer with different frequency/duration combinations. Press [Enter] to start. To stop and exit the test, press any key.

3.3.3 LCD & LED

Test the LCD display and LED indicator. Press [Enter] to start. To stop and exit the test, press any key.

3.3.4 KEYBOARD

Test the rubber keys. Press any key and its corresponding character will be shown on the screen. To stop and exit the test, press [ESC].

3.3.5 MEMORY

Test the data memory (SRAM), and the results will be shown on the screen. To stop and exit the test, press [ESC].

Warning! The contents of the data memory (SRAM) will be wiped out after test.

8500 Series Mobile Computer Reference Manual

3.3.6 TOUCH SCREEN

Test signature capture by using the stylus for handwriting. Press [Enter] to start. To stop and exit the test, press [ESC].

3.3.7 VIBRATOR

Test the vibrator. To stop and exit the test, press [ESC].

3.3.8 ECHO TEST

After a physical connection is established properly, run the utility “Echo Test” on your computer and start this test on your mobile computer. Select a desired baud rate. To stop and exit the test, press [ESC].

IR (Cradle-IR)

This echo test is to verify connectivity via IR between the mobile computer and any cradle.

MODEM

This echo test is to verify connectivity via modem. A telephone line must be connected to the Modem Cradle.

Note: For the Modem Cradle, any value other than 57600 bps (default) must be

configured through the DIP switch on the IR control board.

3.3.9 RFID

Refer to section 1.6 Data Capture for the supported RFID tags.

 Test the reading performance of the RFID reader when a proximity card is present.  To stop and exit the test, press [ESC].

Chapter 3 System Menu

3.4 MEMORY

Here provides information and initialization function of the memory.

3.4.1 SIZE INFORMATION

 Base RAM — onboard SRAM for data memory  Memory Card — data memory  Flash — program memory

3.4.2 INITIALIZE

Initialize the data memory, Base RAM or Memory Card.

Warning! The contents of the data memory (SRAM) will be wiped out after memory

initialization.

8500 Series Mobile Computer Reference Manual

3.5 POWER

Here shows current voltage consumption.

Main (battery)

It shows dynamic status of the battery pack, which is used as the main power source.

Backup (battery)

It shows dynamic status of the button cell, which is used to retain data in SRAM.

Warning! Always examine the battery icon on the device screen so that you will be

alerted for a low battery condition.

Chapter 3 System Menu

3.6 LOAD PROGRAM

Here you can access the Load Program service provided by the kernel. Because the

kernel will take over the job, you will not be able to return to the System Menu by

pressing [ESC]. After downloading, restart the mobile computer to activate the new program.

.SHX Program

Program File

Font File Refer to the Font Files folder on CD-ROM.

Download one of the following C program files and/or one font file:

 AG Runtime  CipherNet Runtime  BASIC Runtime*  User program

(U*.shx)

(85xx-5250.shx, 85xx-VT.shx)

(BC*.shx)

If you have downloaded a BASIC Runtime program, the next time you enter the Load Program submenu you will be able to select whether to download a C program (.SHX) or BASIC program (.SYN).

Note: “Load Basic” menu is only available after you have downloaded a BASIC Runtime

program.

8500 Series Mobile Computer Reference Manual

3.7 BLUETOOTH MENU

This submenu is for the built-in Bluetooth module to work with other Bluetooth enabled devices. You must configure these parameters correctly.

Bluetooth Settings

Connect Setting Items Need to Be Checked

Local Name

Remote Name

Broadcast Me

Power Saving

BT-GPRS AP Name Security

Authentication

PIN Code Network Setting

DHCP

SubNet Mask

Local IP Address

Default Gateway

DNS Server

Domain Name

Default Value SPP DUN PAN

Model no. + Serial no.

---

Enabled

---

Disabled

---

Enabled

255.255.128.0

0.0.0.0

---

(v)*

---

Note: GPRS AP name is ONLY required for DUN-GPRS mode.

Chapter 3 System Menu

3.7.1 INFORMATION

Information of network configuration can be viewed here.

Bluetooth Menu > 1. Information

LIB C library version MAC MAC ID of the Bluetooth module IAM A name given to the mobile computer for identification.

 By default, it is made up of model No. and the serial number. (Identical to 2.

Connect Set > 1. Local Name)

CTY

DHCP DHCP server in use or not IP IP address of the mobile computer Mask Subnet Mask Gate Default Gateway

 "Normal" means all 79 channels are available for frequency-hopping

(There are bandwidth limitations for 2.4 GHz ISM band in some countries. For example, only 23 RF channels are defined instead of 79 RF channels in Japan, Spain and France.)

8500 Series Mobile Computer Reference Manual

3.7.2 CONNECT SETTING

A basic Bluetooth system can be configured as (1) point to point - DUN mode, and (2) point to multi-point - SPP or PAN mode.

Set the following parameters if necessary.

Local Name

Enter a name for identifying the mobile computer.

 By default, it is made up of model No. and the serial number.

Remote Name

Enter a name for making a specific connection.

 The remote name must be one of those in the Freq. Dev. List. Otherwise, the mobile computer

will fail to make a connection with any device without pairing.

 DO NOT specify any remote name when roaming across different groups of APs is required.

Broadcast Me

Options - Enable or Disable

 For initial connection, broadcasting must be enabled so that other Bluetooth devices can

discover the mobile computer.

 For security concerns, you may disable it in future use to hide the mobile computer from other

Bluetooth devices.

Power Saving

This refers to the low power consumption mode. Options - Enable or Disable (Only the Sniff mode is supported.)

BT-GPRS AP Name

For DUN-GPRS mode, enter the AP name for connecting to the content server.

Chapter 3 System Menu

3.7.3 SECURITY

Set or modify security parameters.

Authentication

Options - Enable or Disable

PIN Code

Define the encryption key values.

 Up to 16 characters, using ASCII code.

Note: When authentication is enabled without providing a pre-set PIN code, the mobile

computer supports dynamic input of PIN code during pairing.

8500 Series Mobile Computer Reference Manual

3.7.4 ECHO TESTS

These echo tests are used for verifying connectivity to make sure the mobile computer is within coverage. Press [ESC] to stop and exit the test.

In PAN mode, the echo test helps measure the coverage of the range, estimate the number of APs and mobile computers needed, and determine the topology of deploying APs.

 SPP: Serial Port Profile

It is used for ad hoc networking, without going through any access point.

 DUN: Dial-Up Networking Profile

DUN Modem - It makes use of a Bluetooth modem or mobile phone as a wireless modem.

DUN GPRS – It makes use of a mobile phone with GPRS functionality and connects to GPRS AP.

 BNEP: Bluetooth Network Encapsulation Protocol

It is used by Personal Area Networking Profile (PAN) for IP networking over Bluetooth.

SPP Master

Set the mobile computer as a master device.

1. Pairing with your computer (slave) must be completed first.

2. Run the Echo Test program on your computer. Associated settings include

- Select “RS-232” for interface.

- Use the Bluetooth COM port that has been paired.

- Set Action Mode to “Passive”.

3. Start the echo test on both ends. The mobile computer will try to connect to PC (slave).

SPP Slave

Set the mobile computer as a slave device.

1. Enable Authentication and set your PIN code on the mobile computer.

2. Run the Echo Test program on your computer. Associated settings include

- Select “RS-232” for interface.

Chapter 3 System Menu

- Use the Bluetooth COM port that has been configured as “outgoing”.

- Set Action Mode to “Passive”.

3. Start the echo test on both ends.

4. The mobile computer will wait for PC (master) to start the connection.

5. Enter the preset PIN code for authentication on your computer.

DUN Modem

The mobile computer will try to connect to a Bluetooth modem or mobile phone.

1. Pairing with your mobile phone must be completed first.

Select “DialUp Network” for Target Machine options.

2. Run the Echo Test program on your computer. Associated settings include

- Select “Modem” for interface.

- Set Action Mode to “Passive”.

3. Start the echo test on both ends.

4. The mobile computer will connect to your mobile phone that dials up to your computer.

DUN GPRS

The mobile computer will try to connect to a mobile phone with GPRS functionality.

1. Pairing with your mobile phone must be completed first. Select “DialUp Network” for Target Machine options.

2. Run the Echo Test program on your computer. Associated settings include

- Select “TCP/IP – Server” for interface.

- Set Action Mode to “Passive”.

3. Start the echo test on both ends.

4. Enter the server IP on the mobile computer.

5. The mobile computer will connect to your mobile phone that dials up a GPRS AP, and finally connect to your computer (server) through the GPRS AP.

BNEP Client

Set the mobile computer as a client. Enter the IP address of a server with which a connection is desired. Then, it will try to connect to an AP.

1. Pairing with an AP must be completed first. Select “Access Point” for Target Machine options.

Note that you must disable Authentication and clear the preset PIN code when connecting to Bluetooth AP (3560).

2. Run the Echo Test program on your computer. Associated settings include

- Select “TCP/IP – Server” for interface.

- Set Action Mode to “Passive”.

3. Start the echo test on both ends.

4. Enter the server IP and port number on the mobile computer.

8500 Series Mobile Computer Reference Manual

BNEP Server

Set the mobile computer as a server. It will try to connect to an AP.

1. Pairing with an AP must be completed first. Select “Access Point” for Target Machine options.

Note that you must disable Authentication and clear the preset PIN code when connecting to Bluetooth AP (3560).

2. Run the Echo Test program on your computer. Associated settings include

- Select “TCP/IP – Client” for interface.

- Enter Remote IP and port number.

- Set Action Mode to “Passive”.

3. Start the echo test on both ends.

Chapter 3 System Menu

3.7.5 PAIRING TEST

The pairing procedure is for the creation and exchange of a link key between two Bluetooth-enabled devices. The devices use the link key for future authentication when exchanging information.

1) The mobile computer will start with making an inquiry so that the system can

generate a list of device(s) that has been discovered nearby.

2) Select a desired target device.

3) Select a Bluetooth service from the “Target Machine” menu. To stop and exit the test,

press [ESC].

 Serial Port (SPP)  Access Point (PAN)  DialUp Network (DUN)

After pairing successfully, the target device will be added to the Frequent Device List for quick connection in the future.

Note: During the initial setting of Bluetooth wireless network, the pairing procedure must

be carried out before the Echo tests.

8500 Series Mobile Computer Reference Manual

3.7.6 FREQ. DEV. LIST

The Frequent Device List is used to store a list of target device(s) that the mobile computer has been connected to lately. After each successful pairing, the system will update the list.

Note: To unpair any device, simply delete the device from this list.

This list can show information of up to eight target devices that provides different Bluetooth services.

 It can list only one device that provides the Bluetooth Serial Port service. (SPP)  It can list up to eight APs that provide the Bluetooth Personal Area Networking service.

(PAN)

 It can list only one device that provides the Bluetooth Dial-Up Networking service.

(DUN)

Note: During roaming (for PAN only) or re-establishing the connection, the mobile

computer will automatically connect to the listed AP(s) or target device without going through the pairing procedure.

Chapter 3 System Menu

3.7.7 NETWORK SETTING

Set parameters for IP networking.

DHCP

Options - Enable or Disable

Subnet Mask

Enter a new Mask IP, if necessary.

Local IP Address

Enter a new address for the mobile computer, if necessary.

Default Gateway

Enter a new address for the default Gateway, if necessary.

DNS Server

Enter a new address for the DNS server, if necessary.

Domain Name

The domain name of the host is displayed when DHCP server is enabled.

Note: Normally, DHCP is enabled and all of the settings can be obtained form the DHCP

server.

8500 Series Mobile Computer Reference Manual

3.8 SERIAL PPP MENU

This submenu is for establishing a PPP connection via the Modem Cradle. You must configure these parameters correctly.

Note: Point-to-Point Protocol (PPP) is a method of connecting the mobile computer to the

Internet over serial links. It sends TCP/IP packets to a server that connects to the Internet.

3.8.1 INFORMATION

Information of library version can be viewed here.

Serial PPP Menu > 1. Information

LIB C library version

 Identical to System Menu > 1. Information

Chapter 3 System Menu

3.8.2 CONNECTION SET

DialUp Number

Enter the number provided by your ISP.

Enter the login name provided by your ISP.

Enter the login password provided by your ISP.

Baud Rate

Select a desired baud rate.

Note: By default, the baud rate is set to 57600 bps on the Modem Cradle.

For any other value, such as 115200/38400/19200/9600, you must configure through the DIP switch on the IR control board.

8500 Series Mobile Computer Reference Manual

3.8.3 ECHO TEST

This echo test is used for verifying connectivity via Point-to-Point Protocol. For the

Modem Cradle, its physical connectivity can be verified in System Menu > Tests > Echo Test > IR or MODEM.

Enter the IP address of a server with which a PPP connection is desired. Then, it will try to connect to the server.

Note: After the “PPP via IR” connection is established properly, run the utility “Echo Test”

on your computer (TCP/IP – Server), and then, start this test on your mobile computer.

Chapter 3 System Menu

3.9 IR NETWORK MENU (ETHERNET VIA IR)

This submenu is for Ethernet connection via IR networking. You must configure these parameters correctly.

Note: The Ethernet Cradle is required for establishing Ethernet connection via IR.

3.9.1 INFORMATION

Information of Ethernet network configuration can be viewed here.

IR Network Menu > 1. Information

DHCP DHCP server in use or not IP IP address of the mobile computer Mask Subnet Mask Gate Default Gateway

8500 Series Mobile Computer Reference Manual

3.9.2 NETWORK SETTING

Set parameters for IP networking.

DHCP

Options - Enable or Disable

Subnet Mask

Enter a new Mask IP, if necessary.

Local IP Address

Enter a new address for the mobile computer, if necessary.

Default Gateway

Enter a new address for the default Gateway, if necessary.

DNS Server

Enter a new address for the DNS server, if necessary.

Domain Name

The domain name of the host is displayed when DHCP server is enabled.

Note: Normally, DHCP is enabled and all of the settings can be obtained form the DHCP

server.

Chapter 3 System Menu

3.9.3 ECHO TESTS

The Ethernet Cradle supports three working modes:

 Data Mode  Modem Mode  Transparent Mode

These echo tests are used for verifying connectivity via the Ethernet Cradle. For details, refer to the Ethernet Cradle manual.

Data Mode

Set the Ethernet Cradle in Data mode. The mobile computer works as a client.

Modem Mode

Set the Ethernet Cradle in Modem mode. The mobile computer works as a client.

Transparent Mode

1. Client Mode - Set the mobile computer as a client.

Enter the IP address of a server with which a connection is desired.

2. Server Mode - Set the mobile computer as a server that waits for other devices to connect to.

Note: After the “Ethernet via IR” connection is established properly, run the utility “Echo

Test” on your computer (TCP/IP – Server or Client), and then, start this test on your mobile computer.

8500 Series Mobile Computer Reference Manual

3.10 WI-FI MENU

This submenu is for 802.11b/g wireless networking. You must configure these parameters correctly.

Note: This submenu is generated only when the Wi-Fi module is present.

Wi-Fi Settings Default Value Ad-hoc Infrastructure

Network Setting Items Need to Be Checked

DHCP

SubNet Mask

Local IP Address

Default Gateway

DNS Server

Domain Name

WLAN Setting

Local Name

SS ID

System Scale

Power Saving

Preamble

Ad-Hoc Security

Authentication

WEP Menu

EAP Menu

WPA Menu

Enabled

255.255.128.0

0.0.0.0

---

Model no. + Serial no.

---

Medium

Enabled

Long

Disabled

Open System

Disabled

---

Chapter 3 System Menu

3.10.1 INFORMATION

Information of network configuration can be viewed here.

Wi-Fi Menu > 1. Information

Ver Firmware version of the module chipset MAC MAC ID of the 802.11b/g module ID A name given to the mobile computer for identification.

 By default, it is made up of model No. and the serial number.

(Identical to 3. WLAN Setting > 1. Local Name)

DHCP DHCP server in use or not IP IP address of the mobile computer Mask Subnet Mask Gate Default Gateway

8500 Series Mobile Computer Reference Manual

3.10.2 NETWORK SETTING

Set parameters for IP networking.

DHCP

Options - Enable or Disable

Subnet Mask

Enter a new Mask IP, if necessary.

Local IP Address

Enter a new address for the mobile computer, if necessary.

Default Gateway

Enter a new address for the default Gateway, if necessary.

DNS Server

Enter a new address for the DNS server, if necessary.

Domain Name

The domain name of the host is displayed when DHCP server is enabled.

Note: Normally, DHCP is enabled and all of the settings can be obtained form the DHCP

server.

Chapter 3 System Menu

“

3.10.3 WLAN SETTING

Wireless networking can operate in two modes – (1) Ad-hoc mode: peer-to-peer, and (2) Infrastructure mode: point to multi-point through access points.

Set the following parameters.

Local Name

Enter a name for identifying the mobile computer.

 By default, it is made up of model No. and the serial number.

SS ID

This refers to Service Set ID or Identifier.

 The mobile computer can ONLY communicate with access points that have the same SS ID.

System Scale

This refers to Access Point Density.

Options - [1] Low [2] Medium [3] High

 The value you set must match that set for the access point. 

Low / Medium / High” means the mobile computer will search for other APs only when data

transmission rate is below “1 / 2 / 5” Mbps individually.

Power Saving

This refers to the low power consumption mode.

Options - Enable or Disable

 The value you set must match that set for the access point.

Preamble

Options - [1] Long [2] Short [3] Both

 The value you set must match that set for the access point.

Ad-Hoc

This refers to peer-to-peer mode, without going through access points. Options - Enable or Disable

8500 Series Mobile Computer Reference Manual

3.10.4 SECURITY

Set or modify security parameters.

 WEP: Wired Equivalent Privacy  EAP: Extensible Authentication Protocol  WPA: Wi-Fi Protected Access

Authentication

[1] Open System

[0] Share Key

 Default authentication type  This requires implementing WEP key.

WEP Menu

WEP Setting

 Enabled (For Share Key, it must be enabled!)  Disabled (default)

WEP Key Length

 64 bits  128 bits (default)

Default Key WEP KEY1

WEP Key Enter WEP Keys 1 ~ 4 in one of the following input data type:

 ASCII (up to 13 characters)  Hexadecimal (up to 26 characters)

EAP Menu

EAP Setting

 Enabled  Disabled (default)

EAP ID Enter a user name (up to 32 characters)

EAP Password Enter a password (up to 32 characters)

WPA Menu

WPA Setting

 Enabled  Disabled (default)

WPA Passphrase Enter a phrase as your password (8 ~ 63 characters)

Chapter 3 System Menu

3.10.5 ECHO TESTS

This function is used to measure the coverage of the range, estimate the number of APs and mobile computers needed, and determine the topology of deploying APs.

Client Mode

Set the mobile computer as a client. Enter the IP address of a server with which a connection is desired. Then, it will try to connect to an AP.

1. Run the Echo Test program on your computer. Associated settings include

- Select “TCP/IP – Server” for interface.

- Set Action Mode to “Passive”.

2. Start the echo test on both ends.

3. Enter the server IP and port number on the mobile computer.

Server Mode

Set the mobile computer as a server. The mobile computer will try to connect to an AP.

1. Run the Echo Test program on your computer. Associated settings include

- Select “TCP/IP – Client” for interface.

- Set Action Mode to “Passive”.

2. Start the echo test on both ends.

Note: Run the utility “Echo Test” on your computer (TCP/IP – Server or Client), and start

this test on your mobile computer.

8500 Series Mobile Computer Reference Manual

While running echo tests, if WPA setting is enabled for security, the SSID and Passphrase will be processed to generate a pre-share key.

Note: If you change the SSID or Passphrase, it will have to re-generate a pre-share key.

1) For initial association with an access point, you will see an antenna icon developing

on the screen to indicate that the mobile computer is processing a pre-share key.

2) After having generated the pre-share key, the mobile computer proceeds to establish

a connection with an access point, and you will see the whole antenna is flashing.

3) When the mobile computer has been connected to the access point successfully, you

will see the whole antenna and the indication of wireless signal strength.

Chapter 3 System Menu

Note: If you are programming in C or BASIC, be aware that these icons will appear on

the device screen after NetInit() or START TCPIP() is called. (WPA must be enabled first!)

Once the connection of echo test is established, the details will be displayed as illustrated below. Link Quality (“Q”) will be the most important element while the others are for your reference.

Q (Link Quality)

0 ~ 10

10 ~ 15

15 ~ 30

50 ~ 80

Very Poor

Poor

Good

Very Good

T (Transmit Speed) S (Signal Level) N (Noise Level)

5.5

Mbps

0 ~ 10

30 ~ 60

Over 60

Weak

Moderate

Strong

2 ~ 3

4 ~ 5

Weak

Moderate

Strong

8500 Series Mobile Computer Reference Manual

3.11 GSM/GPRS MENU

This submenu is for GSM/GPRS networking. You must configure these parameters correctly. The required information must be obtained from your GSM/GPRS network operator.

 GSM:

Data services of GSM, including SMS (Short Message Service) and data call, are

provided for receiving and sending data.

 GPRS:

Through Access Points of GPRS, the mobile computer can establish a connection with the content server that connects to the Internet. Only client-initiated connection is supported.

Note: This submenu is generated only when the GSM/GPRS card is present.

3.11.1 INFORMATION

Information of GSM/GPRS configuration can be viewed here.

GSM / GPRS Menu > 1. Information

GSM Network

PIN Personal Identity Number of SIM card for security check. APN Access Point Name of your GPRS operator. DHCP DHCP server in use or not IP IP address of the mobile computer

Undefined.

Chapter 3 System Menu

3.11.2 SECURITY

In order to decide whether to apply security check, you must type the correct PIN code and press [Enter]. You may change the PIN code if necessary.

PIN Code Facility

 Enabled (PIN Code check)  Disabled (default)

PIN Code

Change PIN code of SIM card.

8500 Series Mobile Computer Reference Manual

3.11.3 GPRS SETTING

AP Name

Enter the AP name of your GPRS operator.

DHCP

Options – Enable (default) or Disable

Local IP

Enter a new address for the mobile computer, if necessary.

CHAP Menu

Setting

 Enabled  Disabled (default)

User Name Enter a user name (up to 32 characters)

Password Enter a password (up to 32 characters)

Chapter 3 System Menu

3.11.4 GSM/GPRS TESTS

GSM SMS Test

This GSM Sending Test is used to verify connectivity for Short Message Service. Enter a receiver telephone number on the mobile computer.

GSM Modem Echo

The mobile computer will try to connect to a GSM modem.

1. Run the Echo Test program on your computer. Associated settings include

- Select “Modem” for interface.

- Set Action Mode to “Passive”.

2. Start the echo test on both ends.

3. Enter a receiver telephone number on the mobile computer.

4. The mobile computer will connect to the GSM modem that dials up your computer.

GPRS Client Mode

The mobile computer will try to connect to your GPRS service provider.

1. Run the Echo Test program on your computer. Associated settings include

- Select “TCP/IP – Server” for interface.

- Set Action Mode to “Passive”.

2. Start the echo test on both ends.

3. Enter the server IP on the mobile computer.

4. The mobile computer will dials up to a GPRS AP, and finally connect to your computer (server) through the GPRS AP.

Note: Run the utility “Echo Test” on your computer (TCP/IP – Server or Client) or

“TcpServer.exe” for GPRS Client Mode. Then, start this test on your mobile computer.

8500 Series Mobile Computer Reference Manual

Chapter 4

PROGRAM MANAGER & KERNEL

This chapter explains Program Manager and Kernel that manage multiple programs

and firmware upgrade.

IN THIS CHAPTER

4.1 Program Manager ...................................................... 79

4.2 Kernel ...................................................................... 84

4.1 PROGRAM MANAGER

The mobile computer supports multiple applications and languages. In the menu of

Program Manager, it allows storing up to seven programs and has one activated for the

current use.

If there is no application program exists, the Program Manager will be displayed after

you turn on the mobile computer.

Warning! The Program Manager menu is provided for managing programs in an

administrative level.

How to access the Program Manager menu?

1) Turn off the mobile computer.

2) Press [8] + [Power].

8500 Series Mobile Computer Reference Manual

4.1.1 DOWNLOAD

Here provides a full list of programs that are currently stored on the mobile computer with size information. Multiple application programs can be downloaded through a variety of interfaces. Upon completion of downloading, you are allowed to input a name for the program. If there is no need to rename the program, simply press [ENTER] to leave as it is.

The length of program name can be up to 12 characters. Program size is in kilo bytes.

A suffix letter after the memory sector (1 ~ 6) indicates the file type of program.

 “b” for BASIC program (.SYN)  “c” for C program (.SHX)  “f” for font file (.SHX)

Note: In addition to the system font, there can be only one font file downloaded to the

mobile computer. The custom font file needs to be downloaded through the System Menu or Kernel Menu.

Chapter 4 Program Manager & Kernel

SPARE MEMORY SECTORS (1 ~ 6)

Additional program files can be directly downloaded to these sectors.

Download a program file to an empty sector:

1. Select an empty sector by pressing the corresponding number and then [Enter].

2. Select a desired baud rate for downloading.

3. Connect the RS-232 cable and wait for a few seconds to establish a connection…

4. To abort the action, press [ESC]. Then press [ESC] again to return to the menu.

Download a program file to an occupied sector:

If no available sectors, you'll have to replace one program with the new one.

1. Select a program that you want to delete by pressing the corresponding number and then [Enter].

2. The program information is displayed on the screen.

Press [Alpha] to enter the Alpha mode, and then press [C].

3. Select a desired baud rate for downloading.

4. Connect the RS-232 cable and wait for a few seconds to establish a connection…

5. To abort the action, press [ESC]. Then press [ESC] again to return to the menu.

From the menu, you'll find the program is deleted but no new program is present.

If you simply want to delete a program, press [D] in step 2.

Note: [C], [D] are NOT case-sensitive.

ACTIVE MEMORY SECTOR (“ACT”)

Only the application program, which needs to be activated immediately, can be downloaded to the active memory sector.

Download to Memory Sector “ACT”:

1. Press the [Down] key to select the memory sector “ACT” (may be unoccupied), and then press [Enter].

2. Connect the RS-232 cable and wait for a few seconds to establish a connection…

3. If the active memory sector has already been occupied by an application program, the newly downloaded program will replace the currently active program and come into effect immediately.

8500 Series Mobile Computer Reference Manual

4.1.2 ACTIVATE

The list shows the entire spare programs stored on the mobile computer. From the list, you can select from 1 to 6 and activate one of them. The selected program will be copied to the active memory sector and replace the current one.

Note: A font file cannot be activated.

TO CLEAR FILE SYSTEM

When <New Program Start> screen appears, “Press [ESC] to clear file” means the file system in the SRAM will be cleared out by pressing [ESC]. Then there will be no data (transactions, settings, etc.) stored on the mobile computer when the new program comes into effect.

TO KEEP FILE SYSTEM

To keep the data, simply press any other key.

Chapter 4 Program Manager & Kernel

4.1.3 UPLOAD

You may duplicate one or all of the programs from the mobile computer to a host computer or another mobile computer. This can be used to clone software on mobile computers.

Note: To clone all of the programs, the target mobile computer cannot have any other

program downloaded except the active one; that is, Memory Sectors 1~6 must be empty!

The procedures are similar to those for downloading programs.

8500 Series Mobile Computer Reference Manual

4.2 KERNEL

The kernel resides in the innermost core of the system. It has the highest security and is always protected by the system. When the application program is corrupted and the

System Menu fails, the Kernel Menu provides an access to fix the system.

Warning! The Kernel Menu is NOT for the use of any end users.

How to access the Kernel Menu?

1) When the last session is in the System Menu or Program Manager, simply turn off

the mobile computer. Otherwise, you must reload the battery pack.

2) Press [1] + [7] + [Power].

4.2.1 KERNEL INFORMATION

Here provides important system information to help diagnose the system.

Kernel Menu > 1. Information

H/W Hardware version (PCB) S/N Serial number of the mobile computer M/D Manufacturing date KNL Kernel version DEV 5-digit code for optional hardware configurations

Refer to

Understanding Device Code.

Chapter 4 Program Manager & Kernel

4.2.2 LOAD PROGRAM

You can download one program file to the active memory sector, as well as one font file to the memory address assigned by the system. After downloading, restart the mobile computer to activate the new program.

 New application program or program update  And/or one font file, i.e. multi-language font

If you are using a custom font file rather the system font and you want to download another font file, it is necessary to delete the current font file from the program list displayed by the allowed.

Program Manager first. Otherwise, downloading new font file is not

.SHX Program

Program File

Font File Refer to the Font Files folder on CD-ROM.

Download one of the following C program files and/or one font file:

 AG Runtime  CipherNet Runtime  BASIC Runtime*  User program

(U*.shx)

(85xx-5250.shx, 85xx-VT.shx)

(BC*.shx)

If you have downloaded a BASIC Runtime program, the next time you access the

Load

Program service through the System Menu, you will be able to select whether to

download a C program (.SHX) or BASIC program (.SYN).

Note: To download a BASIC program (*SYN), go to System Menu > 6. Load Program

> 2. Load Basic.

SETTINGS

Interface

Cradle-IR (Serial IR) Proceed to configure baud rate settings on your computer and the

mobile computer.

IrDA Point to the target IrDA device.

Bluetooth Approach the target Bluetooth enabled device.

8500 Series Mobile Computer Reference Manual

Baud Rate

115200 (bps) Supported on CipherLab software, including download utilities.

76800 (bps) N/A

57600 (bps) Supported on CipherLab software, including download utilities.

38400 (bps) Supported on CipherLab software, including download utilities.

19200 (bps) Supported on CipherLab software, including download utilities.

9600 (bps) Supported on CipherLab software, including download utilities.

4800 (bps) N/A

2400 (bps) N/A

Note: If you select to use Serial IR of the Modem Cradle, any value other than 57600

bps (default) must be configured through the DIP switch on the IR control board.

LOAD PROGRAM VIA BLUETOOTH

1) Go to System Menu > 7. Bluetooth Menu > 3. Security, and configure the

following Bluetooth settings first.

 Authentication  PIN code

2) Go to System Menu > 6. Load Program and select Bluetooth.

3) Start the pairing procedure from your computer, for example, click [Pair Device]

and/or [Connect Bluetooth Serial Port].

4) Run any of the download utilities: ProgLoad.exe or Download.exe

- Select interface RS-232/IrDA for using Bluetooth SPP.

- Select COM port properties that match with the serial port settings used on your computer.

Chapter 4 Program Manager & Kernel

4.2.3 KERNEL UPDATE

The kernel might need to be updated to improve performance or due to other considerations.

 To download a kernel update (K*.shx), the procedure is the same as that for

downloading a program.

 Any attempt to download an older version will be rejected.  The system will restart itself right after downloading.

Warning: Do not turn off the mobile computer while downloading a kernel update or

re-starting the mobile computer. Otherwise, it will crash the kernel forever. There is no way to recover it!

Note: CipherLab software, including download utilities, supports the following baud rate

options: 115200/57600/38400/19200/9600 bps.

4.2.4 TEST & CALIBRATE

These tools are provided for manufacturing use.

Warning! You should not perform any of these tests.

8500 Series Mobile Computer Reference Manual

4.2.5 BLUETOOTH MENU

This submenu is the same as the one under the System Menu except for the following

items:

 "2. Connect Set > 5. BT-GPRS AP Name" is not provided.  "4. Echo Tests" is provided with SPP options only.  "7. Network Setting" is not provided.

SPECIFICATIONS

Model Designation

Wireless Communications

Readers

Electrical Characteristics

Physical Characteristics

8500 8570 8580 8590

IR/IrDA √ √ √ √

Bluetooth Class 2 √ √ √ √

802.11b/g – √ – √

GSM/GPRS – – √ √

Barcode Reader

 CCD (linear imager)  Standard Laser  Long Range Laser  Extra Long Range Laser  2D Imager

RFID Reader Frequency 13.56 MHz

Main Battery Rechargeable Li-ion battery – 3.7 V, 4000 mAh

Working Time Laser, one scan per 5 seconds, with backlight on:

 400 hours in batch mode  32 hours in Wi-Fi mode

Backup Battery

 Rechargeable Lithium button cell – 3.0 V, 7 mAh  Data retention – at least 7 days

CPU 32-bit Toshiba CMOS type, 40 MHz

Memory

 Program memory – 2 MB flash  Data memory – 2 MB onboard SRAM, upgradeable

(4 MB/ 8 MB memory card)

Display Graphic LCD, 160 x 160 pixels, 3” FSTN with LED

backlight programmable

 Font size 6x8: 26 characters by 19 lines  Font size 8x16: 20 characters by 9 lines

Also a touch screen allows for the use of stylus for control and signature capture.

Keypad 24 or 44 rubber keys, LED backlight programmable

Indicators

 LED – Dual-color (red/green), programmable  Buzzer – Low power transducer type, 1 KHz to 4

KHz, programmable

Vibrator 9000 ± 2000 RPM, Max. 50 dB, programmable

Enclosure Material Rubber & ABS plastic

Dimensions 230 mm (L) 91 mm (W) 65 mm (H) Weight Approx. 600 g (Laser and battery included)

8500 Series Mobile Computer Reference Manual

Environmental Characteristics

Accessories

Temperature Operating :

Storage:

Humidity Operating :

Storage:

Impact Resistance 1.5 m, 5 drops per 6 sides

Splash / Dust Resistance

Electrostatic Discharge

EMC Regulations FCC, IC, CE, C-Tick, NCC, BSMI, TELEC, MIC

Development Tools

Software & Utilities

IP 64

± 15 kV air discharge, ± 8 kV direct discharge

C and BASIC Programming

Windows-based Application Generator (AG), AG utilities;

Windows-based CipherNet for VT100/220, IBM 5250 emulation;

Download utilities, testing tools, etc.

-20 °C to 60 °C (8500)

-10 °C to 60 °C (8570/8580/8590)

-30 °C to 70 °C

10% to 90% non-condensing

5% to 95% non-condensing

 4 or 8 MB Memory Card  Pistol Grip  Belt Holster  Protective Cover  Spare rechargeable battery pack  4-slot Battery Charger  Charging & Communication Cradle  Modem Cradle (56 K)  Ethernet Cradle (10/100 BASE-T)  Vehicle Cradle  Travel Charger  Bluetooth Access Point  802.11b/g Access Point

CipherLab 8500, 8570, 8580, 8590 Reference Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

IMPORTANT NOTICES

FOR USA

FOR CANADA

FOR HAND-HELD PRODUCT WITH RF FUNCTIONS

FOR PRODUCT WITH LASER

SAFETY PRECAUTIONS

CARE & MAINTENANCE

RELEASE NOTES

INTRODUCTION

GETTING FAMILIARIZED WITH 8500

INSTALLING THE HAND STRAP

INSTALLING THE PISTOL GRIP

CHARGING THE BATTERY

DIMENSIONS

FEATURES

INSIDE THE PACKAGE

ACCESSORIES

USING 8500 MOBILE COMPUTER

1.1 BATTERY

1.1.1 INSERTING THE BATTERY

1.1.2 CHARGING THE BATTERY

1.1.3 CAUTION OF LOW BATTERY CHARGE

1.1.4 POWER MANAGEMENT

1.2 MEMORY

1.2.1 CAUTION OF DATA LOSS

1.2.2 UPGRADEABLE MEMORY

1.3 KEYPAD

1.3.1 SCREEN ICONS

1.3.2 24-KEY LAYOUT

1.3.3 44-KEY KEYPAD

1.4 LCD

1.4.1 ADJUSTING THE BACKLIGHT

1.4.2 CALIBRATING THE SCREEN

1.5 NOTIFICATIONS

1.5.1 STATUS LED

1.5.2 AUDIO

1.5.3 VIBRATOR

1.6 DATA CAPTURE

1.6.1 DUAL-MODE SUPPORT

1.6.2 SYMBOLOGIES SUPPORTED

1.6.3 RFID TAGS SUPPORTED

1.7 COMMUNICATIONS VIA THE CRADLE

1.7.1 SETTING UP THE CRADLE

1.7.2 CRADLE OPTIONS

1.7.3 UNDERSTANDING THE STATUS INDICATORS

1.8 COMMUNICATIONS OVER WIRELESS NETWORKS

1.8.1 IR/IrDA

1.8.2 BLUETOOTH (CLASS 2)

1.8.3 IEEE 802.11b/g

1.8.4 GSM/GPRS

LEARNING SOFTWARE ARCHITECTURE

2.1 APPLICATION MODULE

2.1.1 APPLICATION GENERATOR (AG)

2.1.2 CIPHERNET

2.1.3 USER PROGRAM

2.2 SYSTEM CONFIGURATION

2.2.1 SYSTEM MENU

2.2.2 KERNEL

2.2.3 PROGRAM MANAGER

SYSTEM MENU

3.1 INFORMATION

3.1.1 UNDERSTANDING DEVICE CODE

3.2 SETTINGS

3.2.1 CLOCK

3.2.2 BACKLIGHT PERIOD

3.2.3 AUTO OFF

3.2.4 POWER ON OPTIONS

3.2.5 KEY CLICK

3.2.6 SYSTEM PASSWORD

3.2.7 FONT

3.2.8 SCREEN CALIBRATION

3.2.9 RESET TO DEFAULT

3.2.10 RESET READER

3.2.11 LCD HEATER

3.3 TESTS

3.3.1 READER