Cine Gears 1000TR User Manual
MANUAL BOOK
Product Name:Wireless HD/SDI video transmission system with TALLY and TALKBACK
Model Name:1000tr
Manufacture:ShenZhen LanGi Technology Co. LTD
Contents
Wireless Video Transmission Systems
3
Product Features
4
Specifications
5
User Manual
11
Cautions
2
Transmitter
Receiver
Setting Up the Unit
Setting Up the Intercom
Setting Transmission Output Power
7
9
11
13
13
Channel Settings 14
Turning Fan On/Off
Troubleshooting
Disclaimers
14
15
17
1
Cautions
Warning
Please read this user introduction manual to become familiar with the features before operation.
Failure to operate the product correctly can result in damage to the product,
or interference with other devices. This is a sophisticated product which must be operated with caution and
common sense. Failure to operate this product properly might result in disturbing other film equipment on set.
This product is not intended for use by children without direct adult supervision. Do not use with incompatible
components, or alter this product in any way outside of the documents provided by. These safety guidelines
contain instructions for installation, operation, and maintenance. It is essential to read and follow all of the
instruction in the manual, and all the notices and warnings regarding series products prior to assembly, setup,
or use to prevent any damage or interference.
1. Do not use this product in extreme heat, cold, dusty, or humid environments.
2. Prevent friction against hard objects.
3. Prevent jarring, such as from falling from high places, or from improper packaging during transportation.
4. These products are not waterproof; prevent moisture from getting in, on, or around the unit(s).
5. Do not dismantle, assemble, or otherwise alter the product(s) arbitrarily.
Electrical Considerations
1. When this device is sharing a power supply or battery with other equipment, please make sure all signal
and power cables are well connected before turning on the unit power.
2. When this device is sharing a power supply or battery with other equipment, please make cables from the
unit.
3. When this device is sharing a power supply or battery with other equipment, please check the polarity of
the power connectors of all equipment to ensure the inside conductor is positive. If the polarity of the power
connector is unknown, please check the user manual to make sure the outer conductor of the SDI or HDMI
connector is connected to the negative of the power supply. Otherwise, the equipment will not be able to
share the same power supply with the unit.
2
4
Product Features
Transmits 10-bit color, YCbCr, 4:2:2 color depth, proprietary color matching algorithm on OFDM
chips.
Optimized uncompressed 10-bit 4:2:2 2GBps video stream, or 12-bit 4:4:4 3GBPs wireless video
transmission on other models.
Optimized video processor for on-screen movement.
Fully supports all audio formats.
Static channel selection. The channel number and frequency can be modified by software to avoid
interference from other devices. Supports multiple receivers and AES 128 bit video encryption.
FPGA technology adopting American IRTA programmable logic matrix chips.
Follows the international film association time code protocols. Accurate time code extraction,
transmission, and encryption using embedded time code transmission method. Hardware
encrypted time code to IRTA chips.
Software allows user to adjust transmission output power to avoid interference.
Uses a separate channel to transmit tally information. Fully supports different intercom interfaces.
Integrated wireless intercom feature supports up to 300 meters for microphone and speakers.
5
Transmitter
SPECIFICATION
Frequency
Low band: 5190 and 5230MHz
High band: 5755 and 5795MHz
2.4-2.483GHz with ISM band
Modulation method and
Bandwidth
OFDM/40MHz for video
GFSK/1MHz for intercom system
Video Formats
Supported
1080p 23.98/24/25/30/50/60
1080psf 23.98/24/25
1080i 50/59.94/60
720p 50/59.94/60
576p 576i 480p 480i
Audio Formats
Supported
PCM, DTS-HD, Dolby TrueHD
Time Code
SMPTE-12M
Transmission Range
2500ft(Line of sight)
Transmitter
Antenna
External Antenna 5G × 2pcs
External Antenna 2.4G x1pcs
Transmission Power
18dBm
Functional Interface
HDMI Input; SDI Input; SDI Loop Output; Mini
USB; LEMO Power IN; Antenna RPSMA
Socket; Power ON/OFF,3.5mm HP/MIC socket
TALLY output for Wrist
Mounting Structure
1/4” Hot-shoe connection
OLED Display
Channel Info; Video status; Battery capacity;
Status Menu, Audio Volume
Power Source
9-18V for DC input, V-Mount or G-Mount
battery (depending on the model)
Power Consumption
7.5-8.5W
Specifications
Specifications
6
Net Weight(with
antenna)
400g
Temperature
-10-40º (Operating); -40-80º (Storage)
Receiver
Antenna
External Antenna for 5G × 5pcs
External Antenna for 2G x1pcs
Receiving Sensitivity
-70dBm
Functional Interface
SDI Dual Output; HDMI Output; Mini USB;
LEMO Power IN; Antenna RPSMA Socket;
Power ON/OFF, 3.5mm HP/MIC socket;3.5mm
TALLY socket; LEMO 6 needle
Locating Structure
1/4” Hot-shoe connection
OLED Display
Channel Info; Signal Strength; Power Info;
TALLY indicator
Power Source
9-18V for DC input; V-Mount or G-Mount
battery (depending on the model)
Power Consumption
7.5-8.5W
Net Weight(with
antenna)
800g
Temperature
-10-40º (Operating); -40-80º (Storage)
Loading...