Chrysler 300C 2008 Owner's Manual

2008 300

2008

OWNER’S MANUAL

300

SECTION PAGE

1

INTRODUCTION

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

4

UNDERSTANDING YOUR INSTRUMENT PANEL

5

STARTING AND OPERATING

6

WHAT TO DO IN EMERGENCIES

7

MAINTAINING YOUR VEHICLE

8

MAINTENANCE SCHEDULES

9

IF YOU NEED CONSUMER ASSISTANCE

TABLE OF CONTENTS

.............................................................3

...............................9

...............................81

................................... 195

.................................................295

...............................................391

...............................................411

..................................................477

..........................................485

1
2
3
4
5
6
7
8
9

10

INDEX

....................................................................495

10

CONTENTS

INTRODUCTION

1

䡵 Introduction ...........................4

䡵 How To Use This Manual ..................4

䡵 Warnings And Cautions ...................6

䡵 Vehicle Identification Number ...............6

䡵 Vehicle Modifications / Alterations ...........7

4 INTRODUCTION

INTRODUCTION

This manual has been prepared with the assistance of
service and engineering specialists to acquaint you with
the operation and maintenance of your new vehicle. It is
supplemented by a Warranty Information Booklet and
various customer oriented documents. You are urged to
read these publications carefully. Following the instruc­tions and recommendations in this manual will help
assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored
in the vehicle for convenient reference and remain with
the vehicle when sold, so that the new owner will be
aware of all safety warnings.

When it comes to service, remember that your dealer
knows your vehicle best, has the factory-trained techni­cians and genuine Mopar威 parts, and is interested in
your satisfaction.

HOW TO USE THIS MANUAL

Consult the table of contents to determine which section
contains the information you desire.

The detailed index, at the rear of this manual, contains a
complete listing of all subjects.

Consult the following table for a description of the
symbols that may be used on your vehicle or throughout
this owner manual:

INTRODUCTION 5

1

6 INTRODUCTION

WARNINGS AND CAUTIONS

This manual contains WARNINGS against operating
procedures, which could result in an accident or bodily
injury. It also contains CAUTIONS against procedures,
which could result in damage to your vehicle. If you do
not read this entire manual, you may miss important
information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The vehicle identification number (VIN) is on the left
front corner of the instrument panel. The VIN is visible
from outside of the vehicle through the windshield. This
number also appears on the Automobile Information
Disclosure Label affixed to a windowonyourvehicle, the
vehicle registration, and the title.

VIN LOCATION

NOTE: It is illegal to remove the VIN.

VEHICLE MODIFICATIONS / ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could
seriously affect its roadworthiness and safety and
may lead to an accident resulting in serious injury or
death.

INTRODUCTION 7

1

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

䡵 A Word About Your Keys ..................12

▫ Wireless Ignition Node (WIN) .............12

▫ FOB With Integrated Key .................12

▫ Tip Start Feature .......................14

▫ Ignition Key Removal ...................14

▫ Key-In-Ignition Reminder ................15

䡵 Sentry Key ............................15

▫ Replacement Keys ......................16

▫ Customer Key (FOB) Programming ..........17

2

▫ General Information ....................18

䡵 Security Alarm System — If Equipped .........18

▫ Rearming Of The System .................18

▫ To Arm The System .....................19

▫ To Disarm The System ...................19

䡵 Illuminated Entry System ..................20

䡵 Remote Keyless Entry .....................20

▫ To Unlock The Doors ...................21

▫ To Lock The Doors .....................23

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

▫ To Unlatch The Trunk ...................24

▫ Using The Panic Alarm ..................25

▫ Programming Additional Transmitters ........25

▫ Transmitter Battery Service ...............25

▫ General Information ....................26

䡵 Remote Starting System — If Equipped ........27

▫ How To Use Remote Start ................27

䡵 Door Locks ............................29

▫ Manual Door Locks .....................29

▫ Power Door Locks .....................30

▫ Child Protection Door Lock ...............33

䡵 Windows .............................36

▫ Power Windows .......................36

▫ Wind Buffeting ........................39

䡵 Trunk Lock And Release ...................40

䡵 Trunk Safety Warning .....................41

▫ Trunk Emergency Release ................41

䡵 Occupant Restraints ......................42

▫ Lap/Shoulder Belts .....................43

▫ Lap/Shoulder Belt Untwisting Procedure .....48

▫ Seat Belt Pretensioners ...................48

▫ Enhanced Seat Belt Reminder System

(BeltAlert威) ..........................49

▫ Automatic Locking Mode — If Equipped .....50

▫ Seat Belts And Pregnant Women ............51

▫ Seat Belt Extender ......................51

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11

▫ Driver And Front Passenger Supplemental

Restraint System (SRS) - Airbag ............52

▫ Event Data Recorder (EDR) ...............65

▫ Child Restraint ........................67

䡵 Engine Break-In Recommendations ...........76

䡵 Safety Tips ............................77

▫ Transporting Passengers .................77

▫ Lock Your Vehicle ......................77

▫ Exhaust Gas ..........................78

▫ Safety Checks You Should Make Inside

The Vehicle ..........................79

▫ Periodic Safety Checks You Should Make

Outside The Vehicle ....................79

2

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS

Your vehicle uses a keyless ignition system. This system
consists of a Fob with Integrated Key and a Wireless
Ignition Node (WIN) with integral ignition switch. You
can insert the double-sided integrated key into the igni­tion switch with either side up.

Wireless Ignition Node (WIN)

The Wireless Ignition Node (WIN) operates similar to an
ignition switch. It has four operating positions, three of
which are detented and one spring-loaded. The detented
positions are LOCK, ACC, and ON. The START position
is a spring-loaded momentary contact position. When
released from the START position, the switch automati­cally returns to the detented ON position.

Wireless Ignition Node (WIN)

Fob with Integrated Key

The Fob with Integrated Key operates theignitionswitch.
It also contains the Remote Keyless Entry (RKE) trans­mitter and a valet key, which stores in the rear of the Fob.

The valet key allows for entry into the vehicle should the
battery in the vehicle or the Fob go dead. The valet key is
also for locking the glove box. You can keep the valet key
with you when valet parking.

To remove the valet key from the Fob, slide the mechani­cal latch at the top of the Fob sideways with your thumb
and then pull the key out of the Fob with your other
hand.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

2

Valet Key Removal

NOTE: You can insert the double-sided valet key into

the lock cylinders with either side up.

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Tip Start Feature

Do not press the accelerator. Use the Fob with Integrated
Key to briefly turn the ignition switch to the START
position and release it as soon as the starter engages. The
starter motor will continue to run, and it will disengage
automatically when the engine is running.

Ignition Key Removal

Place the selector lever in “P” (Park). Turn the key to the
LOCK position and then remove the key.

NOTE:

•

For vehicles not equipped with the Electronic Vehicle
Information Center (EVIC), the power window
switches, radio, power sunroof (if equipped), and
power outlets will remain active for 10 minutes after
the ignition switch is turned to the LOCK position.
Opening either front door will cancel this feature.

•

For vehicles equipped with the Electronic Vehicle
Information Center (EVIC), the power window

switches, radio, power sunroof (if equipped), and
power outlets will remain active for up to 60 minutes
after the ignition switch is turned to the LOCK posi­tion. Opening either front door will cancel this feature.
The time for this feature is programmable. For details,
refer to “Delay Power Off to Accessories Until Exit,”
under “Personal Settings (Customer Programmable
Features),” under “Electronic Vehicle Information
Center (EVIC)” in Section 4 of this manual.

WARNING!

Never leave children alone in a vehicle. Leaving
children in a vehicle unattended is dangerous for a
number of reasons. A child or others could be seri­ously or fatally injured. Don’t leave the key in the
ignition. A child could operate power windows,
other controls, or move the vehicle.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

CAUTION!

An unlocked car is an invitation to thieves. Always
remove key from the ignition and lock all doors
when leaving the vehicle unattended.

Key-In-Ignition Reminder

If you open the driver’s door and the key is in the
ignition, a chime will sound to remind you to remove the
key.

NOTE: The Key-In-Ignition reminder only sounds
when the ignition key is placed in the LOCK or ACC
position.

SENTRY KEY

The Sentry Key Immobilizer System prevents unautho­rized vehicle operation by disabling the engine. The
system does not need tobearmed or activated. Operation
is automatic, regardless of whether the vehicle is locked
or unlocked.

The system uses the factory-mated Fob with Integrated
Key and Wireless Ignition Node (WIN) to prevent unau­thorized vehicle operation. Therefore, only Fobs that are
programmed to the vehicle can be used to start and
operate the vehicle. The system will shut the engine off in
two (2) seconds if someone uses an invalid Fob to start
the engine.

After turning the ignition switch to the ON position, the
Vehicle Security Alarm Indicator Light will turn on for
three (3) seconds for a bulb check. If the light remains on
after the bulb check, it indicates that there is a problem
with the electronics. In addition, if the light begins to

2

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

flash after the bulb check, it indicates that someone used
an invalid Fob to start the engine. Either of these condi­tions will result in the engine being shut off after two (2)
seconds.

If the Vehicle Security Alarm Indicator Light turns on
during normal vehicle operation (vehicle running for
longer than 10 seconds), it indicates that there is a fault in
the electronics. Should this occur, have the vehicle ser­viced as soon as possible.

NOTE:

•

The Sentry Key Immobilizer System is not compatible
with aftermarket remote starting systems. Use of these
systems may result in vehicle starting problems and
loss of security protection.

•

Exxon/Mobil Speed Pass,™ additional Fobs, or any
other transponder-equipped components on the same
key chain will not cause a fault unless the additional
part is physically held against the Fob being used to

start the vehicle. Cell phones, pagers, or other RF
electronics will notcause interference with this system.

All of the Fobs provided with your new vehicle have
been programmed to the vehicle electronics.

Replacement Keys

NOTE: Only Fobs that are programmed to the vehicle
electronics can be used to start and operate the vehicle.
Once a Fob is programmed to a vehicle, it cannot be
programmed to any other vehicle.

CAUTION!

Always remove Sentry Keys from the vehicle and
lock all doors when leaving the vehicle unattended.

At the time of purchase, the original owner is provided
with a four-digit PIN number. Keep the PIN in a secure

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

location. This number is required for dealer replacement
of Fobs. Duplication of Fobs may be performed at an
authorized dealer or by using the Customer Key Pro­gramming procedure. This procedure consists of pro­gramming a blank Fob to the vehicle electronics. A blank
Fob is one, which has never been programmed.

NOTE: When having the Sentry Key Immobilizer
System serviced, bring all vehicle Fobs with you to the
dealer.

Customer Key (Fob) Programming

If you have two valid sentry keys, you can program new
sentry keys to the system by performing the following
procedure:

1. Insert the first valid key into the ignition switch and
turn the ignition switch ON for at least 3 seconds but no
longer than 15 seconds. Turn the ignition switch OFF and
remove the first key.

2. Insert the second valid key and turn the ignition
switch ON within 15 seconds. After ten seconds, a chime
will sound and the Vehicle Security Alarm Indicator
Light will begin to flash. Turn the ignition switch OFF
and remove the second key.

3. Insert a blank Sentry Key into the ignition switch and
turn the ignition switch ON within 60 seconds. After 10
seconds, a single chime will sound and the Vehicle
Security Alarm Indicator Light will stop flashing, turn on
again for 3 seconds, and then turn off.

The new Sentry Key is programmed. The Keyless Entry

Transmitter will also be programmed during this pro­cedure.

Repeat this procedure to program up to 8 keys. If you do
not have a programmed sentry key, contact your dealer
for details.

2

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: If a programmed key is lost, see your dealer to
have all remaining keys erased from the systems
memory. This will prevent the lost key from starting your
vehicle. The remaining keys must then be repro­grammed. All vehicle keys must be taken to the dealer at
the time of service to be reprogrammed.

General Information

The Sentry Key system complies with FCC rules part 15
and with RSS-210 of Industry Canada. Operation is
subject to the following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference that may be
received, including interference that may cause undes­ired operation.

SECURITY ALARM SYSTEM — IF EQUIPPED

The Vehicle Security Alarm system monitors the vehicle
doors for unauthorized entry and the ignition switch for
unauthorized operation. If something triggers the alarm,
the system will prevent the vehicle from starting and
provide the following audible and visual signals: the
horn will pulse; the headlights will flash; the park lights
will flash; and the Vehicle Security Alarm Indicator light
in the instrument cluster will flash.

Rearming of the System:

If something triggers the alarm, and no action is taken to
disarm it, the system will turn off the horn after 3
minutes, turn off all of the visual signals after 15 minutes,
and then the system will rearm itself.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

To Arm the System:

Remove the key from the ignition switch and either press
a power door lock switch while the driver or passenger
door is open or press the LOCK button on the Remote
Keyless Entry (RKE) transmitter. After the last door is
closed, or if all doors are closed, the system will arm itself
in about 16 seconds. During that time, the Vehicle Secu­rity Alarm Indicator light will flash. If it does not
illuminate, the system is not arming. Also, if you open a
door during the arming period, the system will cancel the
arming process. If you wish to rearm the system after
closing the door, you must repeat one of the previously
described arming sequences.

To Disarm the System:

Either press the UNLOCK button on the RKE transmitter
or insert a valid ignition key into the ignition switch and
turn the key to the ON position.

NOTE:

•

The driver’s door key cylinder and thetrunkbutton on
the RKE transmitter cannot arm or disarm the system.

•

The system remains armed during trunk entry. Press­ing the trunk button will not disarm the system. If
someone enters the vehicle through the trunk and
opens any door the alarm will sound.

•

When the system is armed, the interior power door
lock switches will not unlock the doors.

The Vehicle Security Alarm system is designed to protect
your vehicle; however, you can create conditions where
the system will give you a false alarm. If one of the
previously described arming sequences has occurred, the
system will arm regardless of whether you are in the
vehicle or not. If you remain in the vehicle and open a
door, the alarm will sound. If this occurs, disarm the
system.

2

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

If the alarm system is armed and the battery becomes
disconnected the system will remain armed when the
battery is reconnected. The exterior lights will flash, the
horn will sound, and the ignition will not start the
vehicle. If this occurs, disarm the system.

Tamper Alert

If something has triggered the system in your absence,
the horn will sound three times when you disarm the
system. Check the vehicle for tampering.

ILLUMINATED ENTRY SYSTEM

The courtesy lights will turn on when you use the
Remote Keyless Entry (RKE) transmitter or open any
door.

This feature also turns on the approach lighting in the
outside mirrors (if so equipped). For details, refer to
“Outside Mirrors with Turn Signal & Approach Light­ing” under “Mirrors” in Section 3 of this manual.

The lights will fade to off after about 30 seconds or they
will immediately fade to off once the ignition switch is
turned ON from the LOCK position.

NOTE:

•

None of the courtesy lights will operate if the dimmer
control is in the “defeat” position (extreme downward
position), unless the overhead map/reading lights are
turned on manually.

REMOTE KEYLESS ENTRY

This system allows you to lock or unlock the doors, open
the trunk, or activate the panic alarm from distances up
to about 35 feet (11 meters) using a hand held radio
transmitter. The transmitter need not be pointed at the
vehicle to activate the system.

NOTE: Inserting the Fob with Integrated Key into the
ignition switch disables all buttons on that transmitter;
however, the buttons on the remaining transmitters will

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21

continue to work. Driving at speeds 5 mph (8 km/h) and
above disables all transmitter buttons for all Fobs.

Keyless Entry Transmitter

To unlock the doors:

Press and release the UNLOCK button on the transmitter
once to unlock the driver’s door, or twice within 5
seconds to unlock all doors. The turn signal lights will
flash to acknowledge the unlock signal. The illuminated
entry system will also turn on.

Remote Key Unlock, Driver Door/All Doors First

This feature lets you program the system to unlock either
the driver’s door or all doors on the first press of the
UNLOCK button on the transmitter. To change the cur­rent setting, proceed as follows:

•

For vehicles equipped with the Electronic Vehicle
Information Center (EVIC), refer to “Remote Key
Unlock,” under “Personal Settings (Customer Pro­grammable Features),” under “Electronic Vehicle In­formation Center (EVIC)” in Section 4 of this manual
for details.

2

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

•

For vehicles not equipped with the EVIC, perform the
following procedure:

1. Press and hold the LOCK button on a programmed
transmitter for at least 4 seconds, but no longer than 10
seconds. Then, press and hold the UNLOCK button
while still holding the LOCK button.

2. Release both buttons at the same time.

3. Test the feature while outside of the vehicle, by
pressing the LOCK/UNLOCK buttons on the transmitter
with the ignition switch in the LOCK position, and the
key removed.

4. Repeat these steps if you want to return this feature to
its previous setting.

NOTE: Pressing the LOCK button on the transmitter
while you are inside the vehicle will activate the Security

Alarm. Opening a door with the SecurityAlarm activated
will cause the alarm to sound. Press the UNLOCK button
to deactivate the Security Alarm.

Flash Lights with Remote Key Lock

This feature willcausethe turn signal lights to flash when
the doors are locked or unlocked with the transmitter.
This feature can be turned on or turned off. To change the
current setting, proceed as follows:

•

For vehicles equipped with the Electronic Vehicle
Information Center (EVIC), refer to “Flash Lights with
Remote Key Lock,” under ⬙Personal Settings (Cus­tomer Programmable Features),” under “Electronic
Vehicle Information Center (EVIC)” in Section 4 of this
manual for details.

•

For vehicles not equipped with the EVIC, perform the
following procedure:

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

1. Press and hold the UNLOCK buttonona programmed
transmitter for at least 4 seconds, but no longer than 10
seconds. Then, press and hold the LOCK button while
still holding the UNLOCK button.

2. Release both buttons at the same time.

3. Test the feature while outside of the vehicle, by
pressing the LOCK/UNLOCK buttons on the transmitter
with the ignition switch in the LOCK position, and the
key removed.

4. Repeat these steps if you want to return this feature to
its previous setting.

NOTE: Pressing the LOCK button on the transmitter
while you are in the vehicle will activate the Security
Alarm. Opening a door with the SecurityAlarm activated
will cause the alarm to sound. Press the UNLOCK button
to deactivate the Security Alarm.

Turn Headlights On with Remote Key Unlock

This feature activates the headlights for up to 90 seconds
when the doors are unlocked with the transmitter. The
time for this feature is programmable on vehicles
equipped with the Electronic Vehicle Information Center
(EVIC). For details, refer to “Turn Headlights On with
Remote Key Unlock,” under “Personal Settings (Cus­tomer Programmable Features),” under “Electronic Ve­hicle Information Center (EVIC)” in Section 4 of this
manual.

To lock the doors:

Press and release the LOCK button on the transmitter to
lock all doors. The turn signal lights will flash and the
horn will chirp to acknowledge the signal.

2

24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Sound Horn with Remote Key Lock

This feature will cause the horn to chirp when the doors
are locked with the transmitter. This feature can be
turned on or turned off. To change the current setting,
proceed as follows:

•

For vehicles equipped with the Electronic Vehicle
Information Center (EVIC), refer to “Sound Horn with
Remote Key Lock,” under “Personal Settings (Cus­tomer Programmable Features),” under “Electronic
Vehicle Information Center (EVIC)” in Section 4 of this
manual for details.

•

For vehicles not equipped with the EVIC, perform the
following steps:

1. Press the LOCK button on a programmed transmitter
for at least 4 seconds, but no longer than 10 seconds.
Then, press the PANIC button while still holding the
LOCK button.

2. Release both buttons at the same time.

3. Test the feature while outside of the vehicle, by
pressing the LOCK button on the transmitter with the
ignition switch in the LOCK position, and the key
removed.

4. Repeat these steps if you want to return this feature to
its previous setting.

NOTE: Pressing the LOCK button on the transmitter
while you are in the vehicle will activate the Security
Alarm. Opening a door with the SecurityAlarm activated
will cause the alarm to sound. Press the UNLOCK button
to deactivate the Security Alarm.

To unlatch the trunk:

Press the trunk button on the transmitter two times
within 5 seconds to unlatch the trunk.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

Using The Panic Alarm:

To turn the panic alarm feature ON or OFF, press and
hold the PANIC button on the transmitter for at least one
second and release. When the panic alarm is on, the
headlights and park lights will flash, the horn will pulse
on and off, and the interior lights will turn on.

The panic alarm will stay on for 3 minutes unless you
turn it off by either pressing the PANIC button a second
time or drive the vehicle at a speed of 15 mph (24 km/h)
or greater.

NOTE:

•

The interior lights will turn off if you turn the ignition
switch to the ACC or ON position while the panic
alarm is activated. However, the exterior lights and
horn will remain on.

•

You may need to be less than 35 feet (11 meters) from
the vehicle when using the transmitter to turn off the
panic alarm due to the radio frequency noises emitted
by the system.

Programming Additional Transmitters

Refer to SENTRY KEY “Customer Key (Fob) Program­ming.” (See page 17 for more information.)

If you do not have a programmed transmitter, contact
your dealer for details.

Transmitter Battery Service

The recommended replacement battery is one CR2032
battery.

NOTE:

•

Perchlorate Material — special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate

2

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

•

Do not touch the battery terminals that are on the back
housing or the printed circuit board.

1. Battery access is through a door located on the rear of
the Fob. Insert a small, flat blade screwdriver into the slot
and gently pry open the access door.

Battery Replacement

2. Remove and replace the batteries. Avoid touching the
new batteries with your fingers. Skin oils may cause
battery deterioration. If you touch a battery, clean it with
rubbing alcohol.

3. Reposition the access door panel over the battery
opening and snap into place.

General Information

This device complies with part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference received,
including interference that may cause undesired op­eration.

NOTE: Changes or modifications not expressly ap­proved by the party responsible for compliance could
void the user’s authority to operate the equipment.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27

If your Remote Keyless Entry (RKE) transmitter fails to
operate from a normal distance, check for these two
conditions.

1. A weak battery in the transmitter. The expected life of
the battery is a minimum of three years.

2. Closeness to a radio transmitter such as a radio station
tower, airport transmitter, and some mobile or CB radios.

REMOTE STARTING SYSTEM — IF EQUIPPED

This system uses the Remote Keyless Entry (RKE) trans­mitter to start the engine conveniently from outside the
vehicle while still maintaining security. The system has a
targeted range of 328 ft. (100 m).

NOTE: The vehicle must be equipped with an auto­matic transmission to be equipped with Remote Start.

How To Use Remote Start

All of the following conditions must be met before the
engine will remote start:

•

Gear selector lever in “P” (Park).

•

Doors closed.

•

Hood closed.

•

Trunk closed.

•

Hazard switch off.

•

Brake switch inactive (brake pedal not pressed).

•

Ignition key removed from ignition switch.

•

Battery at an acceptable charge level.

•

RKE Panic button not pressed.

2

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To Enter Remote Start Mode

Press and release the Remote Start button on
the RKE transmitter twice within 5 seconds.
The parking lights will flash and horn will

honk twice (if programmed). Then, the engine
will start and the vehicle will remain in the Remote Start
mode for a 15-minute cycle.

NOTE:

•

The park lamps will turn on and remain on during
Remote Start mode.

•

For security, power window and power sunroof op­eration (if so equipped) is disabled when the vehicle is
in the Remote Start mode.

•

The engine can be started two consecutive times (two
15-minute cycles) with the RKE transmitter. However,
the ignition switch must be cycled to the ON position
before you can repeat the start sequence for a third
cycle.

To Exit Remote Start Mode without Driving the
Vehicle

Allow the engine to run for the entire 15-minute cycle.

To Exit Remote Start Mode & Drive the Vehicle

Before the end of the 15-minute cycle, press and release
the UNLOCK button on the RKE transmitter to unlock
the doors and disarm the Vehicle Security Alarm (if
equipped). Then, prior to the end of the 15-minute cycle,
insert the key into the ignition switch and turn the switch
to the ON position.

NOTE: The ignition switch must be in the ON position
in order to drive the vehicle.

To Turn Off the Engine While in Remote Start
Mode

Press and release the remote start button one time.

NOTE: To avoid inadvertent shut downs, the system
will disable the one-time press of the remote start button
for two seconds after receiving a valid remote start
request.

DOOR LOCKS
Manual Door Locks

To lock each door, push the door lock plunger on each
door trim panel downward. To unlock each door, pull the
door lock plunger on each door trim panel upward.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29

2

Door Lock Plunger

If the door lock plunger is down when you shut the door,
the door will lock. Therefore, make sure the key is not
inside the vehicle before closing the door.

30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

•

For personal security and safety in the event of an
accident, lock the vehicle doors as you drive as
well as when you park and leave the vehicle.

•

When leaving the vehicle, always remove the key
from the ignition, and lock your vehicle. Unsuper­vised use of vehicle equipment may cause severe
personal injuries and death.

•

Never leave children alone in a vehicle. Leaving
children in a vehicle unattended is dangerous for a
number of reasons. A child or others could be
seriously or fatally injured. Don’t leave the keys in
the ignition. A child could operate power win­dows, other controls, or move the vehicle.

Power Door Locks

A power door lock switch is on each front door trim
panel. Use this switch to lock or unlock the doors.

Power Door Lock Switch

If you press the power door lock switch while the key is
in the ignition, and any front door is open, the power

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31

locks will not operate. This prevents you from acciden­tally locking the key in the vehicle. Removing the key or
closing the door will allow the locks to operate. If a door
is open, the key is intheignition, and the ignition is in the
LOCK or ACC position, a chime willsoundasa reminder
to remove the key.

Automatic Door Locks

The doors will lock automatically on vehicles with power
door locks if all of the following conditions are met:

1. The Automatic Door Locks feature is enabled.

2. The transmission is in gear.

3. All doors are closed.

4. The throttle is pressed.

5. The vehicle speed is above 15 mph (24 km/h).

6. The doors were not previously locked using the power
door lock switch or Remote Keyless Entry (RKE) trans­mitter.

Automatic Door Locks Programming

The Automatic Door Locks feature can be enabled or
disabled as follows:

•

For vehicles equipped with the Electronic Vehicle
Information Center (EVIC), refer to “Personal Settings
(Customer Programmable Features)” under “Elec­tronic Vehicle Information Center (EVIC)” in Section 4
of this manual for details.

•

For vehicles not equipped with the EVIC, performing
the following procedure:

1. Close all doors and place the key in the ignition
switch.

2

32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. Cycle the ignition switch between LOCK and ON and
then back to LOCK 4 times ending up in the LOCK
position.

3. Depress the power door lock switch to lock the doors.

4. A single chime will indicate the completion of the
programming.

5. Repeat these steps if you want to return this feature to
its previous setting.

NOTE: Use the Automatic Door Locks feature in accor­dance with local laws.

Automatic Unlock Doors on Exit

The doors will unlock automatically on vehicles with
power door locks if:

1. The Automatic Unlock Doors On Exit feature is en­abled.

2. The transmission was in gear and the vehicle speed
returned to 0 mph (0 km/h).

3. The transmission is in “N” (Neutral) or “P” (Park).

4. The driver door is opened.

5. The doors were not previously unlocked.

6. The vehicle speed is 0 mph (0 km/h).

Automatic Unlock Doors on Exit Programming

The Automatic Unlock Doors On Exit feature can be
enabled or disabled as follows:

•

For vehicles equipped with the Electronic Vehicle
Information Center (EVIC), refer to “Personal Settings
(Customer Programmable Features)” under “Elec­tronic Vehicle Information Center (EVIC)” in Section 4
of this manual for details.

•

For vehicles not equipped with the EVIC, performing
the following procedure:

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33

1. Close all doors and place the key in the ignition.

2. Cycle the ignition switch between LOCK and ON and
then back to LOCK 4 times ending up in the LOCK
position.

3. Depress the power door unlock switch to unlock the
doors.

4. A single chime will indicate the completion of the
programming.

5. Repeat these steps if you want to return this feature to
its previous setting.

NOTE: Use the AutomaticUnlockDoors On Exit feature
in accordance with local laws.

Child Protection Door Lock

To provide a safer environment for small children riding
in the rear seats, the rear doors are equipped with a child
protection door lock system.

To Engage the Child Protection Door Lock

1. Open the rear door.

2

34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. Insert the tip of the valet key or alike into the child
lock control and pull it upward.

Child Lock Control

3. Repeat Steps 1 and 2 on the opposite rear door.

NOTE: When the child lock system is engaged, the door
can be opened only by using the outside door handle
even though the inside door lock is in the unlocked
position.

WARNING!

Avoid trapping anyone in a vehicle in a collision.
Remember that the rear doors can only be opened
from the outside when the child protection locks are
engaged.

NOTE:

•

After engaging the child protection door lock system,
always test the door from the inside to make certain it
is in the desired position.

•

For emergency exit with the system engaged, move
the door lock switch to the UNLOCK position, roll
down the window and open the door with the outside
door handle.

To Disengage the Child Protection Door Lock

1. Open the rear door.

2. Insert the tip of the valet key or alike into the child
lock control and pull it downward.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35

2

Child Lock Control

3. Repeat Steps 1 and 2 on the opposite rear door.
NOTE: After disengaging the child protection door lock

system, always test the door from the inside to make
certain it is in the desired position.

36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WINDOWS
Power Windows

The window controls on the driver’s door control all the
door windows.

Power Window Switches

There are single window controlson each passenger door
trim panel, which operate the passenger door windows.
The window controls will operate only when the ignition
switch is in the ON or ACC position.

WARNING!

Never leave children in a vehicle, with the keys in
the ignition switch. Occupants, particularly unat­tended children, can become entrapped by the win­dows while operating the power window switches.
Such entrapment may result in serious injury or
death.

Auto Down Feature

The driver door power window switch, and some model
passenger door power window switches have an auto

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37

down feature. Press the window switch to the second
detent, release, and the window will go down automati­cally.

To open the window part way, press the window switch
to the first detent and release it when you want the
window to stop.

To stop the window from going all the way down during
the auto-down operation, pull up on the switch briefly.

For vehicles not equipped with the Electronic Vehicle
Information Center (EVIC), the power window switches
will remain active for 10 minutes after the ignition switch
is turned to the LOCK position. Opening either front
door will cancel this feature.

For vehicles equipped with the EVIC, the power window
switches will remain active for up to 60 minutes after the
ignition switch is turned to the LOCK position. Opening
either front door will cancel this feature. The time is

programmable. For details, refer to “Delay Power Off to
Accessories Until Exit,” under “Personal Settings (Cus­tomer Programmable Features),” under “Electronic Ve­hicle Information Center (EVIC)” in Section 4 of this
manual.

Auto Up Feature with Anti–Pinch Protection — If
Equipped

Lift the window switch to the second detent, release, and
the window will go up automatically.

To stop the window from going all the way up during the
auto-up operation, push down on the switch briefly.

To close the window part way, lift the window switch to
the first detent and release it when you want the window
to stop.

For vehicles not equipped with the Electronic Vehicle
Information Center (EVIC), the power window switches

2

38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

will remain active for 10 minutes after the ignition switch
is turned to the LOCK position. Opening either front
door will cancel this feature.

For vehicles equipped with the EVIC, the power window
switches will remain active for up to 60 minutes after the
ignition switch is turned to the LOCK position. Opening
either front door will cancel this feature. The time is
programmable. For details, refer to “Delay Power Off to
Accessories Until Exit,” under “Personal Settings (Cus­tomer Programmable Features),” under “Electronic Ve­hicle Information Center (EVIC)” in Section 4 of this
manual.

NOTE:

•

If the window runs into any obstacle during auto­closure, it willreverse direction and then stop. Remove
the obstacle and use the window switch again to close
the window.

•

Any impact due to rough road conditions may trigger
the auto reverse function unexpectedly during auto­closure. If this happens, pull the switch lightly to the
first detent and hold to close window manually.

WARNING!

There is no anti-pinch protection when the window
is almost closed. Be sure to clear all objects from the
window before closing.

Window Lockout Switch

The window lockout switch on the driver’s door trim
panel allows you to disable the window controls on the
passenger doors. To disable the window controls, press
and release the window lock button (setting it in the
down position). To enable the window controls, press
and release the window lock button again (setting it in
the up position).

Window Lockout Switch

Reset

Any time the vehicle battery is disconnected, or goes
dead, the auto-up function will be disabled. To reactivate
the auto-up feature, perform the following steps after
vehicle power is restored:

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39

1. Pull the window switch up to close window com­pletely and continue to hold the switch up for an
additional two seconds after the window is closed.

2. Push the window switch down firmly to the second
detent to open the window completely and continue to
hold the switch down for an additional two seconds after
the window is fully open.

Wind Buffeting

Wind buffeting can be described as the perception of
pressure on the ears or a helicopter type sound in the
ears. Your vehicle may exhibit wind buffeting with the
windows down, or the sunroof (if equipped) in certain
open or partially open positions. This is a normal occur­rence and can be minimized. If the buffeting occurs with
the rear windows open, then open the front and rear
windows together to minimize the buffeting. If the
buffeting occurs with the sunroof open, then adjust the
sunroof opening to minimize the buffeting.

2

40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

TRUNK LOCK AND RELEASE

The trunk lid can be released from inside the vehicle by
pressing the Trunk Release Button located on the instru­ment panel to the left of the steering wheel.

NOTE: The transmission must be in “P” (Park) before
the switch will operate.

Trunk Release Button

The trunk lid can be released from outside the vehicle by
pressing the trunk button on the Remote Keyless Entry
(RKE) transmitter twice within 5 seconds.

With the ignition switch in the ON position, the trunk
open symbol will display in the instrument cluster indi­cating that the trunk is open. The odometer display will
reappear once the trunk is closed.

With the ignition switch in the LOCK position or the key
removed from the ignition switch, the trunk open symbol
will display until the trunk is closed.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41

TRUNK SAFETY WARNING

WARNING!

Do not allow children to have access to the trunk,
either by climbing into the trunk from outside, or
through the inside of the vehicle. Always close the
trunk lid when your vehicle is unattended. Once in
the trunk, young children may not be able to escape,
even if they entered through the rear seat. If trapped
in the trunk, children can die from suffocation or
heat stroke.

Trunk Emergency Release

2

Emergency Release

The trunk of your vehicle is equipped with an emergency
release handle. It is located on the inside of the trunk lid,
near the latch, and iscoatedso that it glows in a darkened
trunk. Pull on the handle to open the trunk.

42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

OCCUPANT RESTRAINTS

Some of the most important safety features in your
vehicle are the restraint systems. These include the front
and rear seat belts for the driver and all passengers, the
front airbags for both the driver and front passenger, the
optional supplemental side curtain airbags for the driver
and passengers seated next toawindow, andtheoptional
supplemental front-seat-mounted side airbags. If you
will be carrying children too small for adult-size belts,
your seat belts also can be used to hold infant and child
restraint systems.

Please pay close attention to the information in this
section. It tells you how to use your restraint system
properly to keep you and your passengers as safe as
possible.

WARNING!

In a collision, you and your passengers can suffer
much greater injuries if you are not properly buckled
up. You can strike the interior of your vehicle or other
passengers, or you can be thrown out of the vehicle.
Always be sure you and others in your vehicle are
buckled up properly.

Buckle up even though you are an excellent driver, even
on short trips. Someone on the road may be a poor driver
and cause a collision that includes you. This can happen
far away from home or on your own street.

Research has shown that seat belts save lives, and they
can reduce the seriousness of injuries in a collision. Some
of the worst injuries happen when people are thrown
from the vehicle. Seat belts reduce the possibility of

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43

ejection and the risk of injury caused by striking the
inside of the vehicle. Everyone in a motor vehicle should
be belted at all times.

Lap/Shoulder Belts

All seating positions in your vehicle are equipped with
Lap/Shoulder Belts.

The belt webbing retractor is designed to lock during
very sudden stops or impacts. This feature allows the
shoulder part of the belt to move freely with you under
normal conditions. However, in a collision, the belt will
lock and reduce your risk of striking the inside of the
vehicle or being thrown out.

WARNING!

• It is extremely dangerous to ride in a cargo area, inside or
outside of a vehicle. In a collision, people riding in these
areas are more likely to be seriously injured or killed.

• Do not allow people to ride in any area of your vehicle
that is not equipped with seats and seat belts.

• Be sure everyone in your vehicle is in a seat and using a
seat belt properly.

• Wearing a seat belt incorrectly is dangerous. Seat belts
are designed to go around the large bones of your body.
These are the strongest parts of your body and can take
the forces of a collision the best.

Wearing your belt in the wrong place could make your

•

injuries in a collision much worse. You might suffer internal
injuries, or you could even slide out of part of the belt.
Follow these instructionsto wear your seat beltsafely and to
keep your passengers safe, too.

• Two people should never bebelted into asingle seat belt.
People belted together can crash into one another in an
accident, hurting one another badly. Never use a lap/
shoulder belt or a lap belt for more than one person, no
matter what their size.

2

44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Lap/Shoulder Belt Operating Instructions

1. Enter the vehicle and close the door. Sit back and
adjust the front seat.

2. The seat belt latch plate is above the back of your seat.
Grasp the latch plate and pull out the belt. Slide the latch
plate up the webbing as far as necessary to make the belt
go around your lap.

Pulling Out Lap/Shoulder Belt

3. When the belt is long enough to fit, insert the latch
plate into the buckle until you hear a “click.”

Connecting Latch Plate To Buckle

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45

WARNING!

• A belt that is buckled into the wrong buckle will not

protect you properly. Thelap portion could ride too high on
your body, possibly causing internal injuries. Always
buckle your belt into the buckle nearest you.

• A belt that is too loose will not protect you as well. In a

sudden stop, you could move too far forward, increasing
the possibility of injury. Wear your seat belt snugly.

• A belt that is worn under your arm is very dangerous.

Your body could strike the inside surfaces of the vehicle in
a collision, increasing head and neck injury. A belt worn
under the arm can cause internal injuries. Ribs aren’t as
strong as shoulder bones. Wear the belt over your shoulder
so that your strongest bones will take the force in a
collision.

• A shoulder belt placed behind you will not protect you

from injury during a collision. You are more likely to hit
your head in a collision if you do not wear your shoulder
belt. The lap and shoulder belt are meant to be used
together.

2

46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

4. Position the lap belt across your thighs, below your
abdomen. To remove slack in the lap belt portion, pull up
a bit on the shoulder belt. To loosen the lap belt if it is too
tight, tilt the latch plate and pull on the lap belt. A snug
belt reduces the risk of sliding under the belt in a
collision.

Removing Slack From Belt

WARNING!

• A lap belt worn too high can increase the risk of

internal injury in a collision. The belt forces won’t be at
the strong hip and pelvic bones, but across your abdo­men. Always wear the lap belt as low as possible and
keep it snug.

• A twisted belt can’t do its job as well. In a collision, it

could even cut into you. Be sure the belt is straight. If
you can’t straightena belt in your vehicle, takeit to your
dealer and have it fixed.

5. Position the shoulder belt on your chest so that it is
comfortable and not resting on your neck. The retractor
will withdraw any slack in the belt.

6. To release the belt, push the red button on the buckle.
The belt will automatically retract to its stowed position.
If necessary, slide the latch plate down the webbing to
allow the belt to retract fully.

WARNING!

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47

A frayed or torn belt could rip apart in a collision and
leave you with no protection. Inspect the belt system
periodically, checking for cuts, frays, or loose parts.
Damaged parts must be replaced immediately. Do
not disassemble or modify the system. Seat belt
assemblies must be replaced after a collision if they
have been damaged (bent retractor, torn webbing,
etc.).

Adjustable Upper Shoulder Belt Anchorage

In the driver and front passenger seats, the shoulder belt
can be adjusted upward or downwardto position the belt
away from your neck. Push and fully depress the button
above the webbing to release the anchorage, and then
move it up or down to the position that serves you best.

2

Adjusting Upper Shoulder Belt

As a guide, if you are shorter than average, you will
prefer a lower position, and if you are taller than average,
you will prefer a higher position. When you release the
anchorage, try to move it up and down to make sure that
it is locked in position.

48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

In the rear seat, move toward the center of the seat to
position the belt away from your neck.

Lap/Shoulder Belt Untwisting Procedure

Use the following procedure to untwist a twisted lap/
shoulder belt.

1. Position the latch plate as close as possible to the
anchor point.

2. At about 6 to 12 inches (15 to 30 cm) above the latch
plate, grasp and twist the belt webbing 180° to create a
fold that begins immediately above the latch plate.

3. Slide the latch plate upward over the folded webbing.
The folded webbing must enter the slot at the top of the
latch plate.

4. Continue to slide the latch plate up until it clears the
folded webbing.

Seat Belt Pretensioners

The seat belts for both front seating positions are
equipped with pretensioning devices that aredesignedto
remove any slack from the seat belts in the event of a
collision. These devices improve the performance of the
seat belt system by assuringthat the belt is tight about the
occupant in a collision. Pretensioners work for all size
occupants, including those in child restraints.

NOTE: These devices are not a substitute for properseat
belt placement by the occupant. The seat belt still must be
worn snugly and positioned properly.

The pretensioners are triggered by the Occupant Re­straint Controller (ORC) (refer to information on Airbags
in this section). Like the front airbags, the pretensioners
are single use items. After a collision that is severe
enough to deploy the airbags and pretensioners, both
must be replaced.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49

Enhanced Seat Belt Reminder System (BeltAlert姞)

If the driver’s seat belt has not been buckled within 60
seconds of starting the vehicle and if the vehicle speed is
greater than 5 mph (8 km/h), the Enhanced Warning
System (BeltAlert威) will alert the driver to buckle their
seat belt. The driver should also instruct all other occu­pants to buckle their seat belts. Once the warning is
triggered, the Enhanced Warning System (BeltAlert威)
will continue to chime and flash the Seat Belt Reminder
Light for 96 seconds or until the driver’s seat belt is
buckled. The Enhanced Warning System (BeltAlert威) will
be reactivated if the driver’s seat belt is unbuckled for
more than 10 seconds and the vehicle speed is greater
than 5 mph (8 km/h).

BeltAlert威 Programming

The Enhanced Warning System (BeltAlert威) can be en­abled or disabled by your authorized dealer or by
performing the following steps:

NOTE: DaimlerChrysler does not recommend deacti­vating the Enhanced Warning System (BeltAlert威).

1. With all doors closed, and the ignition switch in any
position except ON or START, buckle the driver’s seat
belt.

2. Turn the ignition switch to the ON position, but do not
start the engine. Wait for the Seat Belt Reminder Light to
turn off and then proceed to the next step.

NOTE: You must perform the following steps within 60
seconds of turning the ignition switch to the ON position.

3. Within 60 seconds of turning the ignition switch to the
ON position, unbuckle and then re-buckle the driver’s
seat belt at least three times within 10 seconds, ending
with the seat belt buckled.

2

50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: Watch for the Seat Belt Reminder Light to turn
on while unbuckling the seat belt and turn off while
re-buckling the seat belt. It may be necessary to retract
the seat belt.

4. Turn the ignition switch to the LOCK position. A
single chime will sound to signify that you have success­fully completed the programming.

The Enhanced Warning System (BeltAlert威) can be reac­tivated by repeating this procedure.

NOTE: When the Enhanced Warning System
(BeltAlert威) is deactivated, the Seat Belt Reminder Light
will continue to illuminate as long as the driver’s seatbelt
is unbuckled.

Automatic Locking Mode — If Equipped

In this mode, the shoulder belt is automatically pre­locked. However, the belt will still retract to remove slack
in the shoulder belt. Use The Automatic Locking Mode
any time a child safety seat is installed in a seating
position that has a seat belt with this feature. Seat belts
that have the Automatic Locking Mode feature have a
distinctive label on the webbing. Children 12 years old
and under should be properly restrained in the rear seat
whenever possible.

How To Engage The Automatic Locking Mode

1. Buckle the combination lap and shoulder belt.

2. Grasp the shoulder portion and pull downward until
the entire belt is extracted.

3. Allow the belt to retract. As the belt retracts, you will
here a clicking sound. This indicates the safety belt is
now in the automatic locking mode.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51

How To Disengage The Automatic Locking Mode

Unbuckle the combination lap and shoulder belt and
allow it to retract completely to disengage the automatic
locking mode and activate the vehicle sensitive (emer­gency) locking mode.

Seat Belts and Pregnant Women

We recommend that pregnant women use the seat belts
throughout their pregnancy. Keeping the mother safe is
the best way to keep the baby safe.

Pregnant women should wear the lap part of the belt
across the thighs and as snug across the hips as possible.
Keep the belt low so that it does not come across the
abdomen. That way the strong bones of the hips will take
the force if there is a collision.

Seat Belt Extender

If a seat belt is too short, even when fully extended, and
when the adjustable upper shoulder belt anchorage (if so
equipped) is in its lowest position, your dealer can
provide you with a seat belt extender. This extender
should be used only if the existing belt is not long
enough. When it is not required, remove the extender,
and store it.

WARNING!

Using a seat belt extender when not needed can
increase the risk of injury in a collision. Only use
when the seat belt is not longenoughwhenitis worn
low and snug, and in the recommended seating
positions. Remove and store the extender when not
needed.

2

52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag

This vehicle has front airbags for both the driver and
front passenger as a supplement to the seat belt restraint
systems. The driver’s airbag is mounted in the center of
the steering wheel. The passenger’s front airbag is
mounted in the instrument panel, above the glove com­partment. The words SRS AIRBAG are embossed on the
airbag covers.

Front Airbag Components

NOTE: The front airbags are certified to the Federal

regulations that allow less forceful deployment.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53

The front airbags have a multistage inflator design. This
may allow the airbag to have different rates of inflation
that are based on collision severity.

WARNING!

•

Do not put anything on or around the front airbag
covers or attempt to manually open them. You may
damage the airbags and you could be injured
because the airbags are no longer functional.
These protective covers for the airbag cushions are
designed to open only when the airbags are inflat­ing.

•

Do not drill, cut or tamper with the knee bolster in
any way.

•

Do not mount any accessories to the knee bolster
such as alarm lights, stereos, citizens band radios
etc.

This vehicle may also be equipped with supplemental
side curtain airbags to protect the driver and passengers
sitting next to a window and/or supplemental front-seat­mounted side airbags.

If the vehicle is equipped with supplemental side curtain
airbags, they are located above the side windows. Their
covers are also labeled SRS AIRBAG.

2

54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Window Airbag

NOTE: Airbag covers may not be obvious in the interior

trim; but they will open to allow airbag deployment.
If the vehicle is equipped with supplemental front-seat-

mounted side airbags, they are marked with an SRS label
sewn into the outboard side of the seat.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55

WARNING!

• If your vehicle is equipped with supplemental front-seat­mounted side airbags, do not use accessory seat covers or
place objects between you and the seat airbags; the perfor­mance could be adversely affected and/or objects could be
pushed into you, causing serious injury.

If your vehicle is equipped with supplemental front-seat-

•

mounted side airbags, do not attach cup holders or any other
objects on or around the door. The inflating seat airbag could
drive the object into occupants, causing serious injury.

• If your vehicle is equipped with supplemental side curtain
airbags, do not stack luggage or other cargo up high
enough to blockthe location of the side curtain airbag. The
area where the side curtain airbag is located should remain
free from any obstructions.

• If your vehicle is equipped with supplemental side curtain
airbags, do not have any accessory items installed which
will alter the roof, including adding a sunroof to your
vehicle. Do not add roof racks that require permanent
attachments (bolts or screws) for installation on the vehicle
roof. Donot drill intothe roof ofthe vehicle forany reason.

NOTE: Do not use a clothing bar mounted to the coat

hooks in this vehicle. A clothing bar will impede the
proper performance of the curtain airbags.

Along with the seat belts, front airbags work with the
instrument panel knee bolsters to provide improved
protection for the driver and frontpassenger. Side curtain
and seat airbags also work with seat belts to improve
occupant protection.

While the seat belts are designed to protect you in many
types of collisions, the front airbags will deploy in
moderate to severe frontal collisions. For vehicles so
equipped, the supplemental side curtain airbag and
front-seat-mounted side airbag on the crash side of the
vehicle will also trigger in moderate to severe side
collisions. However, even in collisions where the airbags
deploy, you need the seat belts to keep you in the correct
position for the airbags to protect you properly.

2

56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Here are some simple steps you can take to minimize
the risk of harm from a deploying airbag.

1. Children 12 years old and under should ride buckled
up in the rear seat.

2. Infants in rear-facing child restraints should NEVER
ride in the front seat of a vehicle with a passenger front
airbag. An airbag deployment could cause severe injury
or death to infants in that position.

3. Children that are not big enough to wear the vehicle
seat belt properly (refer to information on Child Restraint
in this section) should be secured in the rear seat in child
restraints or belt-positioning booster seats.

4. Older children who do not use child restraints or
belt-positioning booster seats should ride properly buck­led up in the rear seat. Never allow children to slide the
shoulder belt behind them or under their arm.

5. If a child from 1 to 12 years old must ride in the front
passenger seat because the vehicle is crowded, move the
seat as far back as possible, and use the proper child
restraint (refer to information on Child Restraint in this
section).

6. You should read the instructions provided with your
child restraint to make sure that you areusing it properly.

7. All occupants should use their seat belts properly.

8. The driver and front passenger seats should be moved
back as far as practical to allow the airbags timetoinflate.

9. If your vehicle has supplemental side curtain airbags
and/or supplemental front-seat-mounted side airbags,
do not lean against thedoor, airbags will inflateforcefully
into the space between you and the door.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57

10. If the airbag system in this vehicle needs to be
modified to accommodate a disabled person, contact the
Customer Center. Phone numbers are provided in the ⬙If
You Need Customer Assistance⬙ section in this manual.

WARNING!

•

Relying on the airbags alone could lead to more
severe injuries in a collision. The airbags work
with your seat belt to restrain you properly. In
some collisions, the airbags won’t deploy at all.
Always wear your seat belts even though you have
airbags.

•

Being too close to the steering wheel or instrument
panel during airbag deployment could cause seri­ous injury. Airbags need room to inflate. Sit back,
comfortably extending your arms to reach the
steering wheel or instrument panel.

•

If the vehicle has supplemental side curtain air­bags and/or supplemental front-seat-mounted side
airbags, they also need room toinflate.Donot lean
against the door or window. Sit upright in the
center of the seat.

2

58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Air Bag System Components

The airbag system consists of the following:

•

Occupant Restraint Controller (ORC)

•

Side Remote Acceleration Sensors (if equipped)

•

Airbag Warning Light

•

Driver Airbag

•

Front Passenger Airbag

•

Supplemental Side Curtain Airbags above Side Win­dows (if equipped)

•

Supplemental Front-Seat-Mounted Side Airbags (if
equipped)

•

Steering Wheel and Column

•

Instrument Panel

•

Interconnecting Wiring

•

Seat Belt Reminder Light

•

Knee Impact Bolsters

•

Front Acceleration Sensors

•

Driver and Front Passenger Seat Belt Pretensioners

How The Airbag System Works

The Occupant Restraint Controller (ORC) determines

•

if a frontal collision is severe enough to require the
airbags to inflate. The front airbag inflators are de­signed to provide different rates of airbag inflation
from directionprovided by the ORC. The ORC will not
detect roll over.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59

•

For vehicles so equipped, The ORC also determines if
a side impact is severe enough to deploy the supple­mental side curtain airbag and/or supplemental front­seat-mounted side airbag as required for each type of
impact.

•

The ORC also monitors the readiness of the electronic
parts of the system whenever the ignition switch is in
the START or ON positions. These include all of the
items listed above except the knee bolster, the instru­ment panel, and the steering wheel and column. If the
key is in the LOCK position, in the ACC position, or
not in the ignition, the airbags are not on and they will
not inflate.

•

The ORC also turns on the Airbag Warning
Light in the instrument panel for 6 to 8
seconds as a self-check when the ignition is
first turned on. After the self-check, the

Airbag Warning Light will turn off. If the ORC detects
a malfunction in any part of the system, it turns on the

Airbag Warning Light either momentarily or continu­ously. A single chime will sound if the light comes on
again after initial start up.

WARNING!

Ignoring the AIRBAG Warning Light in your instru­ment panel could mean you won’t have the airbags to
protect you in a collision. If the light does not come
on, stays on after you start the vehicle, or if it comes
on as you drive, have the airbag system checked right
away.

•

The Driver and Front Passenger Airbag/Inflator
Units are located in the center of the steering wheel

and the passenger side of the instrument panel. When
the ORC detects a collision requiring the airbags, it
signals the inflator units. A large quantity of nontoxic
gas is generated to inflate the front airbags. Different

2

60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

airbag inflation rates may be possible based on colli­sion severity. The steering wheel hub trim cover, and
the upper passenger side of the instrument panel
separate and fold out of the way, as the bags inflate to
their full size. The bags fully inflate in about 50 - 70
milliseconds. This is about half of the time that it takes
to blink your eyes. The bags then quickly deflate while
helping to restrain the driver and front passenger. The
driver’s front airbag gas is vented through vent holes
in the sides of the airbag. The passenger’s front airbag
gas is vented through vent holes in the sides of the
airbag. In this way, the airbags do not interfere with
your control of the vehicle.

•

The Knee Impact Bolsters help protect the knees of
the driver and the front passenger, and position every­one for the best interaction with the front airbag.

•

The Supplemental Side Impact SRS Side Curtain
Airbags are designed to activate only in certain side

collisions. When the ORC (with side impact option)
detects a collision requiring the side curtain airbag to
inflate, it signals the inflators on the crash side of the
vehicle. A quantity of nontoxic gas is generated to
inflate the side curtain airbag. The inflating side cur­tain airbag pushes the outside edge of the headliner
out of the way and covers the window. The airbag
inflates in about 30 milliseconds (about one quarter of
the time that it takes to blink your eyes) with enough
force to injure you if you are not belted and seated
properly, or if items are positioned in the area where
the side curtain airbag inflates. This especially applies
to children. The side curtain airbag is only about 3-1/2
inches (9 cm) thick when it is inflated.

•

The Supplemental Front-Seat-Mounted Side Airbags
are designed to activate only in certain side collisions.
When the ORC (with side impact option) detects a
collision requiring the front-seat-mounted side airbag
to inflate, it signals the inflatorsonthe crash side of the

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61

vehicle. A quantity of nontoxic gas is generated to
inflate the front-seat-mounted side airbag. The inflat­ing front-seat-mounted side airbag pushes through the
seam in the seat’s trim cover and opens into the space
between the occupant and the door. The airbag inflates
at a very high speed and with enough force to injure
you if you are not belted and seated properly, or if
items are positioned in the area where the front-seat­mounted side airbag inflates. This especially applies to
children.

The following requirements must be strictly adhered
to:

•

Do not make any modifications to the front seat
components, assembly, or to the seat cover in any
way.

•

Do not use prior or future model year seat covers
not designated for the specific model being re­paired. Always use the correct seat cover specified
for the vehicle.

•

Do not replace the seat cover with an aftermarket
seat cover.

•

Do not add a secondary seat cover other than those
approved by DaimlerChrysler/Mopar.威

•

At no time should any supplemental restraint sys­tem (SRS) component or SRS related component or
fastener be modified or replaced with any part
except those which are approved by
DaimlerChrysler/Mopar.威

2

62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Unapproved modifications or service procedures to
the front seat assembly, its related components, or
seat cover may inadvertently change the airbag de­ployment in case of a frontal crash. This could result
in death or serious injury to the driver or front seat
passenger if the vehicle is involved in an accident. A
modified vehicle may not comply with required
Federal Motor Vehicle Safety Standards (FMVSS).

If A Deployment Occurs

The airbag system is designed to deploy when the ORC
detects a moderate-to-severe collision, tohelprestrain the
driver and front passenger, and then to immediately
deflate.

NOTE: A frontal collision that is not severe enough to
need airbag protection will not activate the system. This
does not mean something is wrong with the airbag
system.

If you do have a collision, which deploys the airbags, any
or all of the following may occur:

•

The nylon airbag material may sometimes cause abra­sions and/or skin reddening to the driver and front
passenger as the airbags deploy and unfold. The
abrasions are similar to friction rope burns or those
you might get sliding along a carpet or gymnasium
floor. They are not caused by contact with chemicals.
They are not permanent and normally heal quickly.
However, if you haven’t healed significantly within a
few days, or if you have any blistering, seeyourdoctor
immediately.

•

As the airbags deflate, you may see some smoke-like
particles. The particles are a normal by-product of the

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63

process that generates the nontoxic gas used for airbag
inflation. These airborne particles may irritate the skin,
eyes, nose, or throat. If you have skin or eye irritation,
rinse the area with cool water. For nose or throat
irritation, move to fresh air. If the irritation continues,
see your doctor. If these particles settle on your
clothing, follow the garment manufacturer’s instruc­tions for cleaning.

•

It is not advisable to drive your vehicle after the
airbags have been deployed. If you are involved in
another collision, the airbags will not be in place to
protect you.

WARNING!

Deployed airbags can’t protect you in another colli­sion. Have the airbags replaced by an authorized
dealer as soon as possible.

Enhanced Accident Response System

In the event of an impact that causes airbag deployment,
with the vehicle stopped, and the vehicle communication
network intact, and the power intact, the Enhanced
Accident Response System performs the following func­tions:

•

Cuts off fuel to the engine.

•

Flashes hazard lights.

•

Turns on the interior lights, which remainonas long as
the battery has power or until the ignition key is
removed.

•

Unlocks the doors automatically.

NOTE: The interior lights can only be deactivated if the
key is removed from the ignition switch or the vehicle is
driven.

2

64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Maintaining Your Airbag System

WARNING!

• Modifications to any part of the airbag system
could cause it to fail when you need it. You
could be injured because the airbags are not
there to protect you. Do not modify the compo­nents or wiring, including adding any kind of
badges or stickers to the steering wheel hub
trim cover or the upper passenger side of the
instrument panel. Do not modify the front
bumper, vehicle body structure, or frame.

• You need proper knee impact protection in a
collision. Do not mount or locate any aftermar­ket equipment on or behind the knee impact
bolster.

• It is dangerous to try to repair any part of the
airbag system yourself. Be sure to tell anyone
who works on your vehicle that it has airbags.

NOTE: Perchlorate Material — special handling may

apply. See www.dtsc.ca.gov/hazardouswaste/
perchlorate.

Airbag Warning Light

You will want to have the airbags ready to
inflate for your protection in an impact. While
the airbag system is designed to be mainte­nance free, if any of the following occurs, have

an authorized dealer service the system promptly:

•

The Airbag Warning Light does not come on or flickers
during the 6 to 8 seconds when the ignition switch is
first turned on.

•

The light remains on or flickers after the 6 to 8 second
interval.

•

The light flickers or comes on and remains on while
driving.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65

Event Data Recorder (EDR)

In the event of an accident, your vehicle is designed to
record up to 5 seconds of specific vehicle data parameters
(see the following list) in an event data recorder prior to
the moment of airbag deployment, or near deployment,
and up to a quarter second of high-speed deceleration
data during and/or after airbag deployment. EDR data
are ONLY recorded if an airbag deploys, or nearly
deploys, and are otherwise unavailable.

NOTE:

1. A near-deployment event occurs when the airbag
sensor detects severe vehicle deceleration usually indica­tive of a crash, but not severe enough to warrant airbag
deployment.

2. Under certain circumstances, EDR data may not be
recorded (e.g., loss of battery power).

In conjunction with other data gathered during a com­plete accident investigation, the electronic data may be

used by DaimlerChrysler Corporation and others to learn
more about the possible causes of crashes and associated
injuries in order to assess and improve vehicle perfor­mance. In addition to crash investigations initiated by
DaimlerChrysler Corporation, such investigations may
be requested by customers, insurance carriers, govern­ment officials, and professional crash researchers, such as
those associated with universities, and with hospital and
insurance organizations.

In the event that an investigation is undertaken by
DaimlerChrysler Corporation (regardless of initiative),
the company or its designated representative will first
obtain permission of the appropriate custodial entity for
the vehicle (usually the vehicle owner or lessee) before
accessing the electronic data stored, unless ordered to
download data by a court with legal jurisdiction (i.e.,
pursuant to a warrant). A copy of the data will be
provided to the custodial entity upon request. General
data that does not identify particular vehicles or crashes

2

66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

may be released for incorporation in aggregate crash
databases, such as those maintained by the US govern­ment and various states. Data of a potentially sensitive
nature, such as would identify a particular driver, ve­hicle, or crash, will be treated confidentially. Confidential
data will not be disclosed by DaimlerChrysler Corpora­tion to any third party except when:

1. Used for research purposes, such as to match data
with a particular crash record in an aggregate database,
provided confidentiality of personal data is thereafter
preserved

2. Used in defense of litigation involving a
DaimlerChrysler Corporation product

3. Requested by police under a legal warrant

4. Otherwise required by law

Data Parameters that May Be Recorded:

•

Diagnostic trouble code(s) and warning lamp status
for electronically-controlled safety systems, including
the airbag system

•

Airbag disable lamp status (if equipped)

•

⬙Time⬙ of airbag deployment (in terms of ignition
cycles and vehicle mileage)

•

Airbag deployment level (if applicable)

•

Impact acceleration and angle

•

Seat belt status

•

Brake status (service and parking brakes)

•

Accelerator status (including vehicle speed)

•

Engine control status (including engine speed)

•

Transmission gear selection

•

Cruise control status

•

Traction/stability control status

•

Tire pressure monitoring system status (if equipped)

Child Restraint

Everyone in your vehicle needs to be buckled up all the
time — babies and children,too. Every state in the United
States and all Canadian provinces require that small
children ride in proper restraint systems. This is the law,
and you can be prosecuted for ignoring it.

Children 12 years and under should ride properly buck­led up in a rear seat, if available. According to crash
statistics, children are safer when properly restrained in
the rear seats rather than in the front.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67

WARNING!

In a collision, an unrestrained child, even a tiny baby,
can become a missile inside the vehicle. The force
required to hold even an infant on your lap could
become so great that you could not hold the child, no
matter how strong you are. The child and others
could be badly injured. Any child riding in your
vehicle should be in a proper restraint for the child’s
size.

2

68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

There are different sizes and types of restraints for
children from newborn size to the child almost large
enough for an adult safety belt. Always check the child
seat Owner’s Manual to ensure you have the correct seat
for your child. Use the restraint that is correct for your
child:

Infants and Child Restraints

Safety experts recommend that children ride

•

rearward-facing in the vehicle until they are at least
one year old and weigh at least20 lbs (9 kg). Twotypes
of child restraints can be used rearward-facing: infant
carriers and “convertible” child seats.

•

The infant carrier is only used rearward-facing in the
vehicle. It is recommended for children who weigh up
to about 20 lbs (9 kg). “Convertible” child seats can be
used either rearward-facing or forward-facing in the
vehicle. Convertible child seats often have a higher
weight limit in the rearward-facing direction than

infant carriers do, so they can be used rearward-facing
by children who weigh more than 20 lbs (9 kg) but are
less than one year old.Both types of child restraints are
held in the vehicle by the lap/shoulder belt or the
LATCH child restraint anchorage system. Refer to
“LATCH — Child Seat Anchorage System (Lower
Anchors and Tether for CHildren)” in this section.

•

Rearward-facing child seats must NEVER be used in
the front seat of a vehicle with the front passenger
airbag unless the airbag is turned off. An airbag
deployment could cause severe injury or death to
infants in this position.

Older Children and Child Restraints

Children who weigh more than 20 lbs (9 kg) and who are
older than one year can ride forward-facing in the
vehicle. Forward-facing child seats and convertible child
seats used in the forward-facing direction are for children
who weigh 20 to 40 lbs (9 to 18 kg) and who are older

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69

than one year. These child seats are also held in the
vehicle by the lap/shoulder belt or the LATCH child
restraint anchorage system. Refer to “LATCH — Child
Seat Anchorage System (Lower Anchors and Tether for
CHildren)” in this section.

The belt-positioning booster seat is for children weighing
more than 40 lbs (18 kg), but who are still too small to fit
the vehicle’s seat belts properly. If the child cannot sit
with knees bent over the vehicle’s seat cushion while the
child’s back is against the seat back, they should use a
belt-positioning booster seat. The child and belt­positioning booster seat are held in the vehicle by the
lap/shoulder belt.

Children Too Large For Booster Seats

Children who are large enough to wear the shoulder belt
comfortably, and whose legs are long enough to bend
over the front of the seat when their back is against the
seat back, should use the lap/shoulder belt in a rear seat.

•

Make sure that the child is upright in the seat.

•

The lap portion should be low on the hips and as snug
as possible.

•

Check belt fit periodically. A child’s squirming or
slouching can move the belt out of position.

•

If the shoulder belt contacts the face or neck, move the
child closer to the center of the vehicle. Never allow a
child to put the shoulder belt under an arm or behind
their back.

NOTE: For additional information, refer to
www.seatcheck.org or call 1–866–SEATCHECK.

2

70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

•

Improper installation can lead to failure of an
infant or child restraint. It could come loose in a
collision. The child could be badly injured or
killed. Follow the manufacturer’s directions ex­actly when installing an infant or child restraint.

•

A rearward facing child restraint should only be
used in a rear seat. A rearward facing child re­straint in the front seat may be struck by a deploy­ing passenger airbag, which may cause severe or
fatal injury to the infant.

Here are some tips on getting the most out of your child
restraint:

•

Before buying any restraint system, make sure that it
has a label certifying that it meets all applicable Safety

Standards. We also recommend that you make sure
that you can install the child restraint in the vehicle
where you will use it before you buy it.

•

The restraint must be appropriate for your child’s
weight and height. Check the label on the restraint for
weight and height limits.

•

Carefully follow the instructions that come with the
restraint. If you install the restraint improperly, it may
not work when you need it.

•

Buckle the child into the seat according to the child
restraint manufacturer’s directions.

•

When your child restraint is not in use, secure it in the
vehicle with the seat belt or remove it from the vehicle.
Do not leave it loose in the vehicle. In a sudden stop or
collision, it could strike the occupants or seat backs
and cause serious personal injury.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71

LATCH — Child Seat Anchorage System (Lower
Anchors and Tether for CHildren)

Your vehicle’s rear seat is equipped with the child
restraint anchorage system called LATCH. The LATCH
system provides for the installation of the child restraint
without using the vehicle’s seat belts, instead securing
the child restraint using lower anchorages and upper
tether straps from the child restraint to the vehicle
structure.

LATCH-compatible child restraint systems are nowavail­able. However, because the lower anchorages are to be
introduced over a period of years, child restraint systems
having attachments for those anchorages will continue to
have features for installation using the vehicle’s seat
belts. Child restraints having tether straps and hooks for
connection to the top tether anchorages have been avail­able for some time. For some older child restraints, many
child restraint manufacturers offer add-on tether strap

kits or retrofit kits. You are urged to take advantage of all
the available attachments provided with your child re­straint in any vehicle.

All three rear-seating positions have lower anchorages
that are capable of accommodating LATCH-compatible
child seats. You should NEVER install LATCH­compatible child seats such that two seats share a com­mon lower anchorage. If installing child seats in adjacent
rear-seating positions, or if your child restraints are not
LATCH-compatible, install the restraints using the vehi­cle’s seat belts.

2

72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

LATCH Anchorages

Installing the LATCH-Compatible Child Restraint
System

We urge that you carefully follow the directions of the
manufacturer when installing your childrestraint. Not all
child restraint systems will be installed as described here.

Again, carefully follow the installation instructions that
were provided with the child restraint system.

The rear seat lower anchorages are round bars,
located at the rear of the seat cushion where it
meets the seat back, and are just visible when

you lean into the rear seat to install the child
restraint. You will easily feel them if you run your finger
along the intersection of the seatback and seat cushion
surfaces.

In addition, there are tether strap anchorages

behind each rear seating position located in the

panel between the rear seat back and the rear

window. These tether strap anchorages are
under a plastic cover with this symbol on it.

Many, but not all restraint systems will be equipped with
separate straps on each side, with each having a hook or
connector for attachment to the lower anchorage and a

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73

means of adjusting the tension in the strap. Forward­facing toddler restraints and some rear-facing infant
restraints will also be equipped with a tether strap, a
hook for attachment to the tether strap anchorage and a
means of adjusting the tension of the strap.

You will first loosen the adjusters on the lower straps and
on the tether strap so that you can more easily attach the
hooks or connectors to the vehicle anchorages. Next,
attach the lower hooks or connectors over the top of the
seat cover material. Then rotate the tether anchorage
cover directly behind the seat where you are placing the
child restraint and attach the tether strap to the anchor­age, being careful to route the tether strap to provide the
most direct path between the anchor and the child
restraint. Finally, tighten all three straps as you push the
child restraint rearward and downward into the seat,
removing slack in the straps according to the child
restraint manufacturer’s instructions.

NOTE:

•

Ensure that the tether strap does not slip into the
opening between the seat backs as you remove slack in
the strap.

•

When using the LATCH attaching system to install a
child restraint, please ensure that all seat belts not
being used for occupant restraints are stowed and out
of reach of children. It is recommended that before
installing the child restraint, buckle the seat belt so the
seat belt is tucked behind the child restraint and out of
reach. If the buckled seat belt interferes with the child
restraint installation, instead of tucking the seat belt
behind the child restraint, route the seat belt through
the child restraint belt path and then buckle it. This
should stow the seat belt out of the reach of an
inquisitive child. Remind all children in the vehicle
that the seat belts are not toys and should not be
played with, and never leave your child unattended in
the vehicle.

2

74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Improper installation of a child restraint to the
LATCH anchorages can lead to failure of an infant or
child restraint. The child could be badly injured or
killed. Follow the manufacturer’s directions exactly
when installing an infant or child restraint.

Installing Child Restraints Using the Vehicle Seat
belt

The passenger seat belts are equipped with either cinch­ing latch plates or automatic locking retractors, which are
designed to keep the lap portion tight around the child
restraint so that it is not necessary to use a locking clip.
Pulling up on the shoulder portion of the lap/shoulder
belt will tighten the belt. The cinching latch plate will

keep the belt tight; however, any seat belt system will
loosen with time, so check the belt occasionally, and pull
it tight if necessary.

Seat belts with an automatic locking retractor have a
distinctive label on the seat belt webbing. The seat belt
must be in the automatic locking mode in order to enable
a child restraint to be tightly installed. Refer to “Auto­matic Locking Mode” in this section for details. A locking
clip should not be necessary once the automatic locking
feature is enabled. Position the shoulder and lap belt on
the child restraint. The automatic locking retractor is
activated by first attaching the child seat, then pulling all
of the webbing out of the retractor, then allowing back in.
Tighten webbing. To release, simply unbuckle the seat
belt by depressing the button, allowing the webbing to
retract into the retractor.

In the rear seat, you may have trouble tightening the
lap/shoulder belt on the child restraint because the
buckle or latch plate is too close to the belt path opening
on the restraint. Disconnect the latch plate from the
buckle and twist the short buckle-end belt several times
to shorten it. Insert the latchplate into the buckle with the
release button facing out.

If the belt still can’t be tightened, or if by pulling and
pushing on the restraint loosens the belt, you may need
to do something more. Disconnect the latch plate from
the buckle, turn the buckle around, and insert the latch
plate into the buckle again. If you still can’t make the
child restraint secure, try a different seating position.

To attach a child restraint tether strap:

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75

2

Tether Strap Mounting

2. Route the tether strap to provide the most direct path
for the strap between the anchor and the child seat.

1. Rotate the cover over the anchor directly behind the
seat where you are placing the child restraint.

3. Attach the tether strap hook (A) of the child restraint to
the anchor (B) and remove slack in the tether strap
according to the child restraint manufacturer’s instruc­tions.

76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: Ensure that the tether strap does not slip into the
opening between the seat backs as you remove slack in
the strap.

WARNING!

An incorrectly anchored tether strap could lead to in­creased head motion and possible injury to the child.
Use only the anchor positions directly behind the child
seat to secure a child restraint top tether strap.

Transporting Pets

Airbags deploying in the front seat could harm your pet.
An unrestrained pet will be thrown about and possibly
injured, or injure a passenger during panic braking or in
a collision.

Pets should be restrained in the rear seat in pet harnesses
or pet carriers that are secured by seat belts.

ENGINE BREAK-IN RECOMMENDATIONS

A long break-in period is not required for the engine in
your new vehicle.

Drive moderately during the first 300 miles (500 km).
After the initial 60 miles (100 km), speeds up to 50 or 55
mph (80 or 90 km/h) are desirable.

While cruising, brief full-throttle acceleration, within the
limits of local traffic laws, contributes to a good break-in.
Wide-open throttle acceleration in low gear can be detri­mental and should be avoided.

The engine oil installed in the engine at the factory is a
high quality energy conserving type lubricant. Oil
changes should be consistent with anticipated climate
conditions under which vehicle operations will occur.
The recommended viscosity and quality grades are
shown in Section 7 of this manual. NON-DETERGENT
OR STRAIGHT MINERAL OILS MUST NEVER BE
USED.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77

A new engine may consume some oil during its first few
thousand miles (kilometers) of operation. This should be
considered as a normal part of the break-in and not
interpreted as an indication of difficulty.

SAFETY TIPS
Transporting Passengers

NEVER TRANSPORT PASSENGERS IN THE CARGO
AREA.

WARNING!

It is extremely dangerous to ride in a cargo area,
inside or outside of a vehicle. In a collision, people
riding in these areas are more likely to be seriously
injured or killed.

Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat belts.

Be sure everyone in your vehicle is in a seat and
using a seat belt properly.

Lock Your Vehicle

Always remove the key from the ignition and lock all
doors when leaving the vehicle unattended, even in your
own driveway or garage. Try to park your vehicle in a
well-lit area and never invite theft by leaving articles of
value exposed.

2

78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Exhaust Gas

Do not run the engine in a closed garage or in confined
areas any longer than needed to move your vehicle in or
out of the area.

If it is necessary to sit in a parked vehicle with the engine
running, adjust your heating or cooling controls to force
outside air into the vehicle. Set the blower at high speed.

The best protection against carbon monoxide entry into
the vehicle body is a properly maintained engine exhaust
system.

Whenever a change is noticed in the sound of the exhaust
system, when exhaust fumes can be detected inside the
vehicle, or when the underside or rear of the vehicle is
damaged, have a competent mechanic inspect the com­plete exhaust system and adjacent body areas for broken,
damaged, deteriorated, or mispositioned parts. Open
seams or loose connections could permit exhaust fumes
to seep into the passenger compartment. In addition,

inspect the exhaust system each time the vehicle is raised
for lubrication or oil change. Replace as required.

WARNING!

•

Exhaust gases can injure or kill. They contain
carbon monoxide (CO) which is colorless and
odorless. Breathing it can make you unconscious
and can eventually poison you. To avoid breathing
(CO) follow the safety tips below.

•

If you are required to drive with the trunk open,
make sure that all windows are closed, and the
climate control blower switch is set at high speed.
DO NOT use the recirculation mode.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79

Safety Checks You Should Make Inside The Vehicle

Seat Belts

Inspect the belt system periodically, checking for cuts,
frays, and loose parts. Damaged parts must be replaced
immediately. Do not disassemble or modify the system.

Front seat belt assemblies must be replaced after a
collision. Rear seat belt assemblies must be replaced after
a collision if they have been damaged (bent retractor, torn
webbing, etc. If there is any question regarding belt or
retractor condition, replace the belt.

Airbag Warning Light

The light should come on and remain on for 6 to 8
seconds as a bulb check when the ignition switch is first
turned ON. If the light is not lit during starting, see you
authorized dealer. If the light stays on, flickers, or comes
on while driving, have the system checked by an autho­rized dealer.

Defroster

Check operation by selecting the defrost mode and place
the blower control on high speed. You should be able to
feel the air directed against the windshield. See your
authorized dealer for service if your defroster is inoper­able.

Periodic Safety Checks You Should Make Outside The Vehicle

Tires

Examine tires for excessive tread wear and uneven wear
patterns. Check for stones, nails, glass, or other objects
lodged in the tread. Inspect the tread and sidewall for
cuts and cracks. Check the wheel nuts for tightness.
Check the tires (including spare) for proper pressure.

Lights

Have someone observe the operation of exterior lights
while you work the controls. Check turn signal and high
beam indicator lights on the instrument panel.

2

80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Door Latches

Check for positive closing, latching, and locking.

Fluid Leaks

Check area under vehicleafter overnight parking for fuel,
engine coolant, oil, or other fluid leaks. Also, if gasoline
fumes are detected or if fuel, power steering fluid, or
brake fluid leaks are suspected, the cause should be
located and corrected immediately.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CONTENTS

䡵 Mirrors ...............................86

▫ Tilt In Reverse Feature — If Equipped .......89

3

▫ Inside Day/Night Mirror .................86

▫ Automatic Dimming Inside Mirror —

If Equipped ..........................86

▫ Outside Mirrors .......................87

▫ Exterior Mirrors Folding Feature —

If Equipped ..........................88

▫ Outside Mirror Auto Dimmer — If Equipped . .88
▫ Outside Mirrors With Turn Signal & Approach

Lighting — If Equipped ..................88

▫ Power Remote Control Mirrors .............89

▫ Heated Remote Control Mirrors —

If Equipped ..........................90

▫ Illuminated Vanity Mirrors — If Equipped ....90

䡵 Hands–Free Communication (UConnect™) —

If Equipped ............................91

▫ Operation ............................93

▫ Phone Call Features ...................100

▫ UConnect™ System Features .............103

82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

▫ Advanced Phone Connectivity ............107

▫ Things You Should Know About Your

UConnect™ System ....................109

▫ General Information ...................117

䡵 Seats ................................117

▫ Power Seats .........................117

▫ Power Reclining Seats ..................118

▫ Lumbar Support ......................119

▫ Head Restraints ......................120

▫ Heated Seats — If Equipped .............120

▫ Folding Rear Seat .....................123

䡵 Driver Memory Seat — If Equipped .........124

▫ Programming The Memory Feature ........124

▫ Linking & Unlinking The Remote Keyless

Transmitter To The Memory Feature ........125

▫ Memory Position Recall .................126

▫ Easy Entry/Exit Seat

(Available With Memory Seat Only) ........127

䡵 To Open And Close The Hood .............128

䡵 Lights ...............................130

▫ Headlight Switch .....................130

▫ Automatic Headlights – If Equipped ........131

▫ Headlights On With Wipers

(Available With Auto Headlights Only) ......132

▫ SmartBeams — If Equipped ..............132

▫ Headlight Time Delay ..................133

▫ Daytime Running Lights — If Equipped .....134

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83

▫ Lights-On Reminder ...................134

▫ Fog Lights — If Equipped ...............134

▫ Multi-Function Lever ...................134

▫ Overhead Console Map/Reading Lights .....136

▫ Interior Lights .......................136

䡵 Windshield Wipers And Washers ............138

▫ Intermittent Wiper System ...............138

▫ Mist Feature .........................139

▫ Windshield Washers ...................139

▫ Headlights On With Wipers

(Available With Auto Headlights Only) ......139

▫ Rain Sensing Wipers — If Equipped ........140

▫ Adding Washer Fluid ..................141

䡵 Headlight Washers — If Equipped ...........142

▫ Adding Washer Fluid ..................143

䡵 Tilt/Telescoping Steering Column ...........144

䡵 Power Tilt/Telescoping Steering Column —

If Equipped ...........................145

䡵 Adjustable Pedals — If Equipped ...........147

䡵 Electronic Speed Control ..................148

▫ Electronic Speed Control Operation ........149

▫ To Activate ..........................149

▫ To Set At A Desired Speed ...............150

▫ To Deactivate ........................150

▫ To Resume Speed .....................150

▫ To Vary The Speed Setting ...............150

3

84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

▫ To Accelerate For Passing ...............151

䡵 Adaptive Cruise Control (ACC) —

If Equipped ...........................152

▫ Adaptive Cruise Control (ACC) Operation . . .154
▫ Activating Adaptive Cruise Control (ACC) . . .154

▫ To Activate ..........................155

▫ To Set a Desired Speed .................156

▫ To Cancel ...........................157

▫ ToTurnOff .........................157

▫ To Resume Speed .....................158

▫ To Vary The Speed Setting ...............158

▫ Setting The Following Distance In ACC ......159

▫ Adaptive Cruise Control (ACC) Menu ......162

▫ Display Warnings & Maintenance ..........165

▫ Precautions While Driving With ACC .......168

▫ General Information ...................172

䡵 Rear Park Assist System — If Equipped .......172

䡵 Overhead Console ......................176

▫ Courtesy/Reading Lights ................176

▫ Sunglasses Storage ....................177

䡵 Garage Door Opener — If Equipped .........177

▫ Programming HomeLink威 ...............178

▫ Gate Operator/Canadian Programming .....181

▫ Using HomeLink威 .....................182

▫ Reprogramming a Single HomeLink威 Button . . 182

▫ Security ............................182

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85

▫ Troubleshooting Tips ...................183

▫ General Information ...................183

䡵 Power Sunroof — If Equipped .............184

▫ Opening Sunroof - Express ..............185

▫ Closing Sunroof - Express ...............185

▫ Pinch Protect Feature ...................185

▫ Pinch Protect Override .................185

▫ Venting Sunroof - Express ...............185

▫ Sunshade Operation ...................186

▫ Wind Buffeting .......................186

▫ Sunroof Maintenance ...................186

▫ Ignition Off Operation ..................186

▫ Sunroof Fully Closed ...................187

䡵 Electrical Power Outlets ..................187

▫ Electrical Outlet Use With Engine Off .......188

䡵 Cup Holders ..........................189

▫ Front Seat Cup Holders .................189

▫ Rear Seat Cup Holders .................189

䡵 Storage ..............................190

▫ Console Features ......................190

▫ CargoArea..........................192

䡵 Load Leveling System — If Equipped ........193

3

86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

MIRRORS
Inside Day/Night Mirror

Adjust the mirror to center on the view through the rear
window. A two-point pivot system allows for horizontal
and vertical mirror adjustment.

Adjusting Rearview Mirror

Annoying headlight glare can be reduced by moving the
small control under the mirror to the night position
(toward rear of vehicle). The mirror should be adjusted
while set in the day position (toward windshield).

Automatic Dimming Inside Mirror — If Equipped

This mirror automatically adjusts for annoying headlight
glare from vehicles behind you. You can turn the feature
on or off by pressing the button at the base of the mirror.
A light, next to the button, will illuminate to indicate
when the dimming feature is activated.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87

Outside Mirrors

To receive maximum benefit, adjust the outside mirror(s)
to center on the adjacent lane of traffic and a slight
overlap of the view obtained from the inside mirror.

Automatic Dimming Mirror

CAUTION!

To avoid damage to the mirror during cleaning, never
spray any cleaning solution directly onto the mirror.
Apply the solution onto a clean cloth and wipe the
mirror clean.

NOTE: The passenger side convex outside mirror will

give a much wider view to the rear, and especially of the
lane next to your vehicle.

WARNING!

Vehicles and other objects seen in the passenger side
convex mirror will look smaller and farther away
than they really are. Relying too much on your
passenger side convex mirror could cause you to
collide with another vehicle or other object. Use your
inside mirror when judging the size or distance of a
vehicle seen in the passenger side convex mirror.

3

88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Exterior Mirrors Folding Feature — If Equipped

Some models have exterior mirrors that are hinged. The
hinge allows the mirror to pivot forward and rearward to
resist damage. The hinge has three detent positions, full
forward, full rearward, and normal.

Outside Mirror Auto Dimmer — If Equipped

This mirror automatically adjusts for annoying headlight
glare from vehicles behind you. You can turn this feature
on or off by pressing the button at the base of the Inside
Rearview Mirror. This feature is also available on the
passenger outside mirror of mirrors equipped with turn
signal and approach lighting.

Outside Mirrors with Turn Signal & Approach
Lighting — If Equipped

Driver and passenger outside mirrors with turn signal
and approach lighting contain four LEDs, which are
located in the upper outer corner of each mirror.

Three of the LEDs are turn signal indicators, which flash
with the corresponding turn signal lights in the front and
rear of the vehicle. Turning on the hazard flashers will
also activate these LEDs.

The fourth (uppermost) LED supplies illuminated entry
lighting, which turns on in both mirrors when you use
the Remote Keyless Entry (RKE) transmitter or open any
door. This LED shines outward to illuminate the front
and rear door handles. It also shines downward to
illuminate the area in front of the doors.

The illuminated entry lighting fades to off after about 30
seconds or it will fade to off immediately once the
ignition switch is turned ON from the LOCK position.

NOTE: The approach lighting will not function when
the gear selector lever is moved out of the “P” (Park)
position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89

Tilt in Reverse Feature — If Equipped

The ⬙Tilt in Reverse⬙ feature tilts the outside rearview
mirrors downward when the ignition switch is to the ON
position and the transmission is in the “R” (Reverse)
position. This feature provides the driver with a better
view of the ground andvehiclein the area of the rear tires
when backing up. The mirrors will move back to their
previous position when the transmission is shifted out of
“R” (Reverse).

The ⬙Tilt in Reverse⬙ feature can be enabled or disabled
through the Electronic Vehicle Information Center (EVIC)
— if equipped. For details, refer to “Personal Settings
(Customer Programmable Features)” under “Electronic
Vehicle Information Center (EVIC)” in Section 4 of this
manual.

Power Remote Control Mirrors

The power mirror switch is located on the driver’s door
trim panel next to the power door lock switch. A rotary
knob selects the left mirror, right mirror, or off position.

After selecting a mirror, move the knob in the same
direction you want the mirror to move. Use the center off
position to guard against accidentally moving a mirror
position.

3

90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Power Mirror Control

NOTE: For vehicles equipped with Driver Memory

Seat, you can use your Remote Keyless Entry (RKE)
transmitter or the memory switch on the driver’s door
panel to return the power mirrors to pre-programmed
positions. Refer to “Driver Memory Seat” in this section
for details.

Heated Remote Control Mirrors — If Equipped

These mirrors are heated to melt frost or ice. This feature
is activated whenever you turn on the Rear Window
Defrost.

Illuminated Vanity Mirrors — If Equipped

An illuminated vanity mirror is on the sun visor. To use
the mirror, rotate the sun visor downward and swing the
mirror cover upward. The light turns on automatically.
Closing the mirror cover turns off the lights.

Illuminated Vanity Mirror

HANDS–FREE COMMUNICATION (UConnect™) —
IF EQUIPPED

NOTE:
Hands-Free Communication (UConnect™) system. Refer
to your “Navigation User’s Manual” for UConnect™
system operating instructions for this radio.

The sales code RER radio contains an integrated

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91

UConnect™ is a voice-activated, hands-free, in- vehicle
communications system. UConnect™ allows you to dial
a phone number with your cellular phone using simple
voice commands (e.g., ⬙Call” ѧ “Mike” ѧ”Work⬙ or ⬙Dial”
ѧ “248-555-1212⬙). Your cellular phone’s audio is trans­mitted through your vehicle’s audio system; the system
will automatically mute your radio when using the
UConnect™ system.

NOTE: The UConnect™ system use requires a cellular
phone equipped with the Bluetooth ⬙Hands-Free Profile,⬙
version 0.96 or higher. See UConnect™ website for sup­ported phones.

NOTE: For UConnect™ customer support, visit the
following web sites:

•

www.chrysler.com/uconnect

•

www.dodge.com/uconnect

•

www.jeep.com/uconnect

•

or call 1–877–855–8400

3

92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

UConnect™ allows you to transfer calls between the
system and your cellular phone as you enter or exit your
vehicle, and enables you to mute the system’s micro­phone for private conversation.

The UConnect™ phone book enables you to store up to
32 names and four numbers per name. Eachlanguage has
a separate 32-name phone book accessible only in that
language. This system is driven through your Blue­tooth™ Hands-Free profile cellular phone. UConnect™
features Bluetooth™ technology - the global standard
that enables different electronic devices to connect to
each other without wires or a docking station, so UCon­nect works no matter where you stow your cellular
phone (be it your purse, pocket, or briefcase), as long as
your phone is turned on and has been paired to the
vehicle’s UConnect™ system. The UConnect™ system
allows up to seven cellular phones to be linked to system.
Only one linked (or paired) cellular phone can be used

with the system at a time. The system is available in
English, Spanish, or French languages (as equipped).

Phone Button

The rearview mirror contains the microphone
for the system (depending on the type of
mirror and radio equipped), and either the

radio or the mirror has the two control buttons
(Phone Button and Voice Recognition Button) that will
enable you to access the system.

Voice Recognition Button

Actual button location may vary with radio.

The individual buttons are described in the

“Operation” section.

The UConnect™ system can be used with any Hands­Free Profile certified Bluetooth™ cellular phone. See
UConnect™ website for supported phones. If your cellu­lar phone supports a different profile (e.g., Headset

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93

Profile) you may not be able to use any UConnect™
features. Refer to your cellular service provider or the
phone manufacturer for details.

The UConnect™ system is fully integrated with the
vehicle’s audio system. The volume of the UConnect™
system can be adjusted either from the radio volume
control knob or from the steering wheel radio control
(right switch), if so equipped.

The radio display will be used for visual prompts from
the UConnect™ system such as ⬙CELL⬙ or caller ID on
certain radios.

Operation

Voice commands can be used to operate the UConnect™
system and to navigate through the UConnect™ menu
structure. Voice commands are required after most
UConnect™ system prompts. You will be prompted for a
specific command and then guided through the available
options.

•

Prior to giving a voice command, one must wait for
the beep, which follows the⬙Ready⬙ prompt or another
prompt.

•

For certain operations, compound commands can be
used. For example, instead of saying ⬙Setup⬙ and then
⬙Phone Pairing,⬙ the following compound command
can be said: ⬙Setup Phone Pairing.⬙

•

For each feature explanation in this section, only the
combined form of the voice command is given. You
can also break the commands into parts and say each
part of the command, when you are asked for it. For
example, you can use the combined form voice com­mand ⬙Phonebook New Entry,⬙ or you can break the
combined form command into two voice commands:
⬙Phonebook⬙ and ⬙New Entry.⬙ Please remember, the
UConnect™ system works best when you talk in a
normal conversational tone, as if speaking to some one
sitting eight feet away from you.

3

94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Voice Command Tree

Refer to “Voice Tree” at the end of this section.

Help Command

If you need assistance at any prompt, or if you want to
know your options at any prompt, say ⬙Help⬙ following
the beep. The UConnect™ system will play all the
options at any prompt if you ask for help.

To activate the UConnect™ system from idle, simply
press the “Phone” button and follow audible prompts for
directions. All UConnect™ system sessions begin with a
press of the “Phone” button on the radio control head.

Cancel Command

At any prompt, after the beep, you can say ⬙Cancel⬙ and
you will be returned to the main menu. However, in a
few instances the system will take you back to the
previous menu.

Pair (Link) UConnect™ System to a Cellular Phone

To begin using your UConnect™ system, you must pair
your compatible Bluetooth™ enabled cellular phone.

To complete the pairing process, you will need to refer­ence your cellular phone owner’s manual. The UCon­nect™ website may also provide detailed instructions for
pairing.

The following are general phone to UConnect™ System
pairing instructions:

•

Press the “Phone” button to begin.

•

After the ⬙Ready⬙ prompt and the following beep, say
⬙Setup Phone Pairing.⬙

•

When prompted, after the beep, say ⬙Pair aPhone⬙ and
follow the audible prompts.

•

You will be asked to say a four-digit pin number,
which you will later need to enter into your cellular.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95

You can enter any four-digit pin number. You will not
need to remember this pin number after the initial
pairing process.

•

For identification purposes, you will be prompted to
give the UConnect™ system a name for your cellular
phone. Each cellular phone that is paired should be
given a unique phone name.

•

You will then be asked to give your cellular phone a
priority level between 1 and 7, 1 being the highest
priority. You can pair up to seven cellular phones to
your UConnect™ system. However, at any given time,
only one cellular phone can be in use, connected to
your UConnect™ System. The priority allows the
UConnect™ system to know which cellular phone to
use if multiple cellular phones are in the vehicle at the
same time. For example, if priority 3 and priority 5
phones are present in the vehicle, the UConnect™
system will use the priority 3 cellular phone when you

make a call. You can select to use a lower priority
cellular phone at any time (refer to ⬙Advanced Phone
Connectivity⬙).

Dial by Saying a Number

•

Press the “Phone” button to begin.

•

After the ⬙Ready⬙ prompt and the following beep, say
⬙Dial.⬙

•

System will prompt you to say the number you want
call.

•

For example, you can say ⬙234-567-8901.⬙ The phone
number that you enter must be of valid length and
combination. Based on the country in which the ve­hicle was purchased, the UConnect™ limits the user
from dialing invalid combination of numbers. For
example, in USA, 234-567-890 is nine digits long,
which is not a valid USA phone number - the closest
valid phone number has ten digits.

3

96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

•

The UConnect™ system will confirm the phone num­ber and then dial. The number will appear in the
display of certain radios.

•

The UConnect™ system will confirm the name and
then dial the corresponding phone number, which
may appear in the display of certain radios.

Call by Saying a Name

•

Press the “Phone” button to begin.

•

After the ⬙Ready⬙ prompt and the following beep, say
“Call.⬙

•

System will prompt you to say the name of the person
you want call.

•

After the ⬙Ready⬙ prompt and the following beep, say
the name of the person you want to call. For example,
you can say ⬙John Doe,⬙ where John Doe is a previ­ously stored name entry in the UConnect™ phone
book. Refer to ⬙Add Names to Your UConnect™
Phonebook,⬙ to learn how to store a name in the phone
book.

Add Names to Your UConnect™ Phonebook
NOTE: Adding names to phone book is recommended

when vehicle is not in motion.

•

Press the “Phone” button to begin.

•

After the ⬙Ready⬙ prompt and the following beep, say
⬙Phonebook New Entry.⬙

•

When prompted, say the nameofthe new entry. Use of
long names helps the voice recognition and it is
recommended. For example, say ⬙Robert Smith⬙ or
⬙Robert⬙ instead of ⬙Bob.⬙

•

When prompted, enter the number designation (e.g.,
⬙Home,⬙⬙Work,⬙⬙Mobile,⬙ or ⬙Pager⬙). This will allow
you to store multiple numbers for each phone book
entry, if desired.

•

When prompted, recite the phone number for the
phone book entry that you are adding.

After you are finished adding an entry into the phone
book, you will be given the opportunity to add more
phone numbers to the current entry or to return to the
main menu.

The UConnect™ system will allow you to enter up to 32
names in the phone book with each name having up to
four associated phone numbers and designations. Each
language has a separate 32-name phone book accessible
only in that language.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97

Phonebook Download

UConnect™ allows the user to download entries from
their phone via Bluetooth. To use this feature, press the
“Phone” button and say “Phonebook Download.” Sys­tem prompts “Ready to accept vcard entry via Blue­tooth…” The system is now ready to accept phonebook
entries from your phone using the Bluetooth Object
Exchange Profile (OBEX). Please see your phone owners’
manual for specific instructions on how to send these
entries from your phone.

NOTE:

•

Phone handset must support Bluetooth OBEX trans­fers of phonebook entries to use this feature.

•

Some phones cannot send phonebook entries if they
are already connected to any system via Bluetooth,
and you may see a message on the phone display that
the Bluetooth link is busy. In this case, the user must
first disconnect or drop the Bluetooth connection to

3

98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

the UConnect™ and then send the address book entry
via Bluetooth. Please see your phone owners’ manual
for specific instructions on how to drop the Bluetooth
connection.

•

If the phonebook entry is longer than 24 characters it
will be use only the first 24 characters.

Edit Entries in the UConnect™ Phonebook
NOTE: Editing names in the phone book is recom-

mended when vehicle is not in motion.

•

Press the “Phone” button to begin.

•

After the ⬙Ready⬙ prompt and the following beep, say
⬙Phonebook Edit.⬙

•

You will then be asked for the name of the phone book
entry that you wish to edit.

•

Next, choose the number designation (home, work,
mobile, or pager) that you wish to edit.

•

When prompted, recite the new phone number for the
phone book entry that you are editing.

After you are finished editingan entry in the phone book,
you will be given the opportunities to edit another entry
in the phonebook, call the number you just edited, or
return to the main menu.

⬙Phonebook Edit⬙ can be used to add another phone
number to a name entry that already exists in the
phonebook. For example, the entry John Doe may have a
mobile and a home number, but you can add John Doe’s
work number later using the ⬙Phonebook Edit⬙ feature.

Delete Entries in the UConnect™ Phonebook
NOTE: Editing phone book entries is recommended

when vehicle is not in motion.

•

Press the “Phone” button to begin.

•

After the ⬙Ready⬙ prompt and the following beep, say
⬙Phonebook Delete.⬙

•

After you enter the Phonebook Delete menu, you will
then be asked for the name of the entry that you wish
to delete. You can either say the name of a phone book
entry that you wish to delete or you can say ⬙List
Names⬙ to hear a list of the entries in the phone book
from which you choose. To select one of the entries
from the list, press the ⬙Voice Recognition⬙ button
while the UConnect™ system is playing the desired
entry and say ⬙Delete.⬙

•

After you enter the name, the UConnect™ system will
ask you which designation you wish to delete, home,
work, mobile, pager, or all. Say the designation you
wish to delete.

•

Note that only the phone book entry in the current
language is deleted.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99

Delete All Entries in the UConnect™ Phonebook

Press the “Phone” button to begin.

•

•

After the ⬙Ready⬙ prompt and the following beep, say
⬙Phonebook Erase All.⬙

•

The UConnect™ system will ask you to verify that you
wish to delete all the entries from the phonebook.

•

After confirmation, the phone book entries will be
deleted.

•

Note that only the phone book in the current language
is deleted.

List All Names in the UConnect™ Phonebook

Press the “Phone” button to begin.

•

•

After the ⬙Ready⬙ prompt and the following beep, say
⬙Phonebook List Names.⬙

3