Christie Digital Systems 38-VIV402-01 User Manual

User's Manual

38-VIV402-01

MODEL

✽ Projection lens is optional.

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE USER'S MANUAL WITH THIS UNIT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center.

TO THE OWNER

SAFETY PRECAUTIONS

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

● This projector produces intense light from the projection lens. Do not stare directly into the lens. Eye damage could result. Be especially careful that children do not stare directly into the beam.

● This projector should be set in the way indicated. If not, it may result in a fire hazard.

● Take appropriate space on the top, sides and rear of the projector

cabinet for allowing air circulation and cooling the projector. Minimum distance should be taken. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous.

● Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes.

● Remote Control Unit, supplied to this projector, emits the laser beam as the laser pointer function from Laser Light Window while pressing LASER button (for 1 minute / LASER POINTER INDICATOR lights red to indicate laser emission). Do not look into Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.

● If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS USER'S MANUAL FOR LATER USE.

SIDE and TOP

REAR

20cm

50cm 50cm

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.

Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the

operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been

damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

Voor de klanten in Nederland

Bij dit product zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.

COMPLIANCES

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA). AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

AC POWER CORD REQUIREMENT

Federal Communication Commission Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

CAUTION!

This is a Class A equipment. This equipment can cause interference in residential areas; in this case, the operator can be asked to take adequate countermeasures.

GROUND

TABLE OF CONTENTS

FEATURES AND DESIGN 6

BEFORE OPERATION 16

COMPUTER MODE 26

VIDEO MODE 35

SETTING 40

APPENDIX 43

PREPARATION 7

NAME OF EACH PART OF PROJECTOR 7 SETTING-UP PROJECTOR 8

CONNECTING AC POWER CORD 8 LENS INSTALLATION 9 POSITIONING PROJECTOR 9 LENS SHIFT ADJUSTMENT 9 PICTURE LEVEL AND TILT ADJUSTMENT 10 MOVING PROJECTOR 10

CONNECTING PROJECTOR 11

TERMINALS OF PROJECTOR 11 CONNECTING TO COMPUTER 14 CONNECTING TO VIDEO EQUIPMENT 15

SIDE CONTROLS AND INDICATORS 16 OPERATION OF REMOTE CONTROL 18

LASER POINTER FUNCTION 18 REMOTE CONTROL BATTERIES INSTALLATION 19

OPERATING ON-SCREEN MENU 20

HOW TO OPERATE ON-SCREEN MENU 20 FLOW OF ON-SCREEN MENU OPERATION 20 MENU BAR 21

SELECTING INPUT SOURCE 26 SELECTING COMPUTER SYSTEM 26

COMPATIBLE COMPUTER SPECIFICATIONS 28

PC ADJUSTMENT 29

AUTO PC ADJUSTMENT 29 MANUAL PC ADJUSTMENT 30

PICTURE IMAGE ADJUSTMENT 32

IMAGE LEVEL SELECT 32 IMAGE LEVEL ADJUSTMENT 33

PICTURE SCREEN ADJUSTMENT 34

SELECTING INPUT SOURCE 35 SELECTING VIDEO SYSTEM 36 PICTURE IMAGE ADJUSTMENT 37

IMAGE LEVEL SELECT 37 IMAGE LEVEL ADJUSTMENT 38

PICTURE SCREEN ADJUSTMENT 39

SETTING MENU 40

OPERATING WIRELESS MOUSE 43 MAINTENANCE 43

WARNING TEMP. INDICATOR 43 AIR FILTER CARE AND CLEANING 44 CLEANING PROJECTION LENS 44 LAMP MANAGEMENT 45 LAMP REPLACEMENT 46

TROUBLESHOOTING 48 TECHNICAL SPECIFICATIONS 50

BASIC OPERATION 22

TURNING ON / OFF PROJECTOR 22 ADJUSTING SCREEN 23

ZOOM ADJUSTMENT 23 FOCUS ADJUSTMENT 23 LENS SHIFT ADJUSTMENT 23 KEYSTONE ADJUSTMENT 23 PICTURE FREEZE FUNCTION 24 NO SHOW FUNCTION 24 P-TIMER FUNCTION 24

SOUND ADJUSTMENT 25

TRADEMARKS

● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.

● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

● Windows and PowerPoint are registered trademarks of Microsoft Corporation.

● Each name of corporations or products in the user's manual is a trademark or a registered trademark of its

respective corporation.

FEATURES AND DESIGN

This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.

◆ Compatibility

This projector widely accepts various video and computer input signals including;

● Computers

IBM-compatible or Macintosh computer up to 1600 x 1200 resolution.

● 6 Color Systems

NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PALN color system can be connected.

● Component Video

Component video signal, such as a DVD player output high definition TV signals including 480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 or 1080i60, can be connected.

● S-Video

S-Video signal, such as a S-VHS VCR output signal, can be connected.

◆ High Resolution Image

◆ Multi-Scan System

This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for troublesome manual adjustment of frequency and other settings.

◆ Keystone Correction

Positioning height of a projector may result in distorted image being displayed in a trapezoid shape. Keystone Correction solves this problem by digitally altering projection to produce undistorted images.

◆ Multilanguage Menu Display

Operation menu is displayed in; English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Chinese, Korean or Japanese.

◆ One-Touch Auto PC Adjustment

Incoming computer video signals are recognized and best adjustment is automatically set by Auto PC Adjustment. No complicated setup is necessary and projection is always precise.

◆ Digital Zoom (for Computer)

Digital Zoom function adjusts image size to approx. 1/4 ~ 49 times of original image size, allowing you to focus on crucial information at a presentation.

◆ Power Management

Power Management function is provided to reduce power consumption while a projector is not in use. This Power Management function operates to turn Projection Lamp off when a projector detects signal interruption and any button is not pressed over 5 minutes. Projection Lamp is automatically turned on again when a projector detects signal or any operation button is pressed. This projector is shipped with this function ON.

◆ Wireless Mouse

Remote Control Unit supplied with this projector has Wireless Mouse function for a connected computer. This function enables you to operate both projector and computer with Remote Control Unit only.

◆ Digital Visual Interface

This projector is equipped with DVI 29-pin terminal for connecting DVI output from a computer.

◆ Laser Pointer Function

Remote Control Unit supplied with this projector includes Laser Pointer function. This function helps you to make a smart presentation on a projected screen.

◆ Progressive Scan Function

This function converts interlace video signals into progressive scan signals and provide fine picture quality.

◆ Motor-driven Lens Shift

Projection lens can be moved up, down left and right with motor-driven lens shift function. This function makes it easy to provide projected image where you want. Zoom and focus can be also adjusted with motor-driven operation.

◆ Multi Versatile Platform

This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from computers and video equipment.

4-built-in Terminal Slots enable you to arrange any combinations of input sources just by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector.

◆ Selectable Terminal Slots

◆ Network board (Optional)

Network board is an optional product to control and set up a projector via the network cable. By accessing to the connected projector using the web browser on your computer. It can be controlled and set up the projector remotely. Contact the sales dealer where you purchased this projector for optional parts.

This projector provides 1024 x 768 dots resolution for computer input and 800 horizontal TV lines. Resolution from a computer between XGA (1024 x 768) and UXGA (1600 x 1200) is compressed into 1024 x 768 dots. This projector can not display image of over 1600 x 1200 dots. When resolution of your computer is more than 1600 x 1200, reset a computer output for lower resolution.

PREPARATION

NAME OF EACH PART OF PROJECTOR

BOTTOM OF CABINET

BACK OF CABINET

HOT AIR EXHAUSTED !

Air blown from exhaust vent is hot. When using or installing a projector, following precautions should be taken.

● Do not put a flammable object near this vent.

● Keep rear grills at least 3’ (1m) away from

any object, especially heat-sensitive object.

● Do not touch this area, especially screws and metallic parts. This area will become hot while a projector is used.

This projector detects internal temperature and automatically controls operating power of Cooling Fans.

FRONT OF CABINET

LAMP COVER

ADJUSTABLE FEET

This projector is equipped with cooling fans for protection from overheating. Pay attention to following to ensure proper ventilation and avoid a possible risk of fire and malfunction.

● Do not cover vent slots.

● Keep bottom clear of any objects.

Obstructions may block cooling air.

AIR INTAKE VENTS

PROJECTION LENS

SPEAKERS

INFRARED

REMOTE RECEIVER

LENS COVER

POWER CORD

CONNECTOR

EXHAUST VENT

MAIN ON / OFF

SWITCH

INFRARED

REMOTE RECEIVER

CARRYING HANDLE

LEVEL AND TILT ADJUST HANDLE

AIR FILTER

ADJUSTABLE FEET

Do not turn on a projector with lens cover attached. High temperature from light beam may damage lens cover and result in fire hazard.

CAUTION

PREPARATION

SETTING-UP PROJECTOR

This projector uses nominal input voltages of 120 V or 200-240 V AC. This projector automatically selects correct input voltage. It is designed to work with singlephase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of type of power supply being in use. Connect a projector with peripheral equipment before turning a projector on. (Refer to pages 12 ~ 15 for connection.)

CONNECTING AC POWER CORD

Connect AC Power Cord (supplied) to a projector. AC outlet must be near this equipment and must be easily accessible.

To POWER CORD CONNECTOR on a projector.

Projector side

AC Outlet side

Ground

CAUTION

AC Power Cord must meet requirement of country where you use a projector. Confirm AC plug type with chart below and proper AC power cord must be used. If supplied AC Power Cord does not match AC outlet, contact your sales dealer.

To AC Outlet.

(120 V AC)

For Continental Europe

For U.S.A. and Canada

To AC Outlet.

(200 - 240 V AC)

PREPARATION

POSITIONING PROJECTOR

Before setting up a projector, install Projection Lens on a Projector.

1. Before installation, check where a projector is used and prepare suitable lens. For specifications of Projection Lens, refer to manual separately attached or contact sales dealer where you purchased a projector.

2. For installation, refer to installation manual supplied to a Projector.

LENS INSTALLATION

When moving or setting up a projector, be sure to replace a Lens Cover to protect a surface. And be careful not to hold or subject a lens to strong forces. It may damage lens, cabinet, or mechanical parts.

Projection lens can be moved up, down, left and right with motor-driven lens shift function. This function makes it easy to provide projected image where you want.

LENS SHIFT ADJUSTMENT

MOVED UP OR DOWN

MOVED LEFT OR RIGHT

Use LENS SHIFT button and POINT UP/DOWN button to move image up or down. (Refer to page 23.)

Use LENS SHIFT button and POINT LEFT/RIGHT button to move image left or right. (Refer to page 23.)

This projector is designed to project on a flat projection surface.

ROOM LIGHT

Brightness in room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide best image.

This projector is equipped with cooling fan to protect it from overheating. Pay attention to following to ensure proper ventilation and avoid a possible risk of fire and malfunction.

● Do not cover vents with papers or other materials.

● Keep rear grill at least 3 feet (1 m) away from any

object.

● Make sure that there are no objects under a projector. An object under a projector may prevent a projector from taking cooling air through bottom vent.

VENTILATION

SCREEN

AIR INTAKE VENT (BOTTOM SIDE)

EXHAUST VENT (REAR SIDE)

PREPARATION

PICTURE LEVEL AND TILT ADJUSTMENT

Picture tilt and projection angle can be adjusted with handles on both sides of a projector. Projection angle can be adjusted to 5.7 degrees upper way.

CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR

● Do not drop or bump a projector, otherwise damages or malfunctions may result.

● When carrying a projector, use a suitable carrying case.

● Do not transport a projector by using a courier or transport service in an unsuitable transport case. This

may cause damage to a projector. To transport a projector through a courier or transport service, consult your dealer and best case should be applied.

For safety, be sure to hold Carrying Handles on both sides by 2 or more people when moving a projector. Moving it unproperly may result in damage of cabinet or person's injury. Replace lens cover and retract feet to prevent damage to lens and cabinet.

Pull up lock buttons on each side of carrying handles and release locks.

Pull carrying handles out fully until it's locked (with a click). Move a projector by holding two handles by 2 or more people.

To retract carrying handles, pull up lock buttons and release lock of handles and press handles fully in until it's locked.

Press knob on handle. Handle pop out.

Turn handles (right and left) until picture is projected on proper position. Adjust height of rear adjustable feet by rotating them until projector properly stabled on table.

Press knob and retract handle.

MOVING PROJECTOR

CARRYING HANDLE

LOCK BUTTONS

LEVEL AND TILT ADJUST HANDLE

ADJUSTABLE FEET

Height of front feet can be adjusted by turning handles.

KNOB

REAR ADJUSTABLE FEET. (Refer to P7).

Pull up lock buttons to release lock.

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired combinations of input sources just by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector.

Pull out terminal by holding handle.

Remove 2 Screws on terminal.

REPLACEMENT OF TERMINAL

Tighten screws to secure terminal.

Replace terminal. Insert terminal along Guide to fit Plug into Socket.

ANALOG RGB

R/Pr G/Y B/Pb H/HV V

CONTROL PORT

DVI

INPUT 1

R/C JACK

USB

RESET

(MONO)

CONTROL PORT

AUDIO

CONTROL PORT

S-VIDEO

VIDEO/Y

INPUT 2INPUT 3

INPUT 4

AUDIO

SERIAL PORT IN

SERIAL PORT OUT

AUDIO OUT

Screws

Guide

Socket

Plug

Figure shows HDB 15-PIN terminal.

DVI Terminal

5 BNC Terminal

AV Terminal

HDB 15-PIN Terminal

4 TERMINAL SLOTS (Factory set)

NOTES ON ORDERING OR USING OPTIONAL INTERFACE BOARD

When ordering or using Optional Interface Board (Terminal Board), contact your sales dealer. When contacting the sales dealer, tell the Optional Control Number (Op.cont.No.) in the menu that is located under Language Select Menu. (See page 40.)

NOTE; When replacement of terminal board, MAIN

ON/OFF switch should be OFF position.

INPUT/OUTPUT TERMINALS

CONNECTING PROJECTOR

When controlling computer with Remote Control of this projector, connect mouse port of your personal computer to these connectors. (Refer to P14.)

Connect S-VIDEO output from video equipment to this jack. (Refer to P15.)

Connect audio output from computer or video equipment to these jacks. (Refer to P14, 15.)

CONTROL PORT CONNECTORS

AUDIO INPUT JACKS

5 BNC INPUT JACKS

S-VIDEO INPUT JACK

Connect component video output (Cr, Y, Cb or Pr, Y, Pb) from video equipment to R/Pr, G/Y and B/Pb jacks or connect computer output [5 BNC Type (Red, Green, Blue, Horiz. Sync and Vert. Sync.)] from computer to R/Pr, G/Y, B/Pb, H/HV and V jacks. (Refer to P14,

15)

Connect computer output (Digital/Analog DVI-I type) to this terminal. (Refer to P14.)

DVI INPUT TERMINAL

INPUT/OUTPUT TERMINALS AND JACKS

Connect computer output (Analog HDB 15-pin type) to this terminal. (Refer to P14.)

HDB 15-PIN INPUT TERMINAL

AV INPUT (VIDEO/Y, C) JACKS

Connect composite video output from video equipment to VIDEO/Y jack or connect Separate Y/C video outputs to VIDEO/Y and C jacks. (Refer to P15.)

INPUT 2

INPUT 1 INPUT 1, 2, 3, 4

INPUT 1, 2, 4

INPUT 3

INPUT 4

INPUT 3

SERIAL PORT IN

SERIAL PORT OUT

R/C JACK

AUDIO OUT

USB

RESET

R/Pr G/Y B/Pb H/HV V

VIDEO/Y

ANALOG RGB

AUDIO

DVI

S-VIDEO

AUDIO

CONTROL PORT

(MONO)

CONTROL PORT

INPUT 1

INPUT 2INPUT 3

(MONO)

INPUT 4

CONNECTING PROJECTOR

Connect an external audio amplifier to these jacks. (Refer to P14, 15.)

AUDIO OUTPUT JACKS

This projector uses a micro processor to control unit. Occasionally, micro processor may malfunction and need to be reset. This can be done by pressing RESET button with a pen, which will shut down and restart unit. Do not use RESET function excessively.

RESET BUTTON

When using Wired / Wireless Remote Control Unit as Wired Remote Control, Connect Wired Remote Control Unit to this jack with Remote Control Cable (supplied). (Refer to page 19.)

R/C JACK

USB PORT (Series B)

SERIAL PORT

OUT TERMINAL

SERIAL PORT

IN TERMINAL

This port is used to control a projector with computer. It is also used to control computer with Remote Control of this projector. (Refer to P41-43.) Connect USB port of computer to this port.

If you control a projector by computer, you must connect a cable (not provided) from your computer to this terminal.

This terminal outputs signal from SERIAL PORT IN. More than two projectors can be controlled with one computer by connecting SERIAL PORT IN. of another projector to this terminal.

R/C JACK

SERIAL PORT IN

SERIAL PORT OUT

USB

AUDIO OUT

RESET

DVI

R/Pr G/Y B/Pb H/HV V

VIDEO/Y

ANALOG RGB

S-VIDEO

AUDIO

CONTROL PORT

(MONO)

CONTROL PORT

INPUT 1

CONTROL PORT

INPUT 2INPUT 3

(MONO)

INPUT 4

CONNECTING PROJECTOR

CONNECTING TO COMPUTER

IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA/UXGA)

VGA Cable

Monitor Output

Desktop type Laptop type

Control Cable for Serial Port

Audio Cable

(stereo)

✽

Serial port

PS/2 port

Audio Output

Audio Input

AUDIO OUT

Use one of these Control Cables corresponding with terminal of your computer.

MAC/VGA Adapter

Set slide switches following chart below.

ADB port

Cables used for connection (✽ = Cables are not supplied with this projector.)

• VGA Cable (HDB 15 pin)

•

Control Cable for PS/2 port, Serial port, or ADB port

• MAC/VGA Adapter, DVI/VGA Adapter

• DVI Cable

• BNC Cable (BNC x 5)

✽

• Audio Cables (RCA x 2) ✽

Control Cable

for PS/2 Port

Control Cable

for ADB Port

Audio Cable

(stereo)

✽

NOTE :

When connecting cable, power cords of both a projector and external equipment should be disconnected from AC outlet. Turn a projector and peripheral equipment on before computer is switched on.

Terminals of

a Projector

Audio Amplifier

Audio Speaker

(stereo)

External Audio Equipment

Monitor Output

DVI Cable

BNC Cable

✽

Monitor Output

Set switches as shown in table below depending on RESOLUTION MODE that you want to use before your turn on a projector and computer

13"MODE (640 x 480)

16"MODE (832 x 624)

19"MODE (1024 x768)

21"MODE (1152 x 870)

OFF

OFF OFF OFF OFF

OFF OFFOFF

OFF OFF OFF

ON ON ON

OFF

OFF OFF

ON ON

1 2 3 4 5 6

MODE

SWITCHES

Switches of MAC/VGA Adapter

MAC/VGA ADAPTER

DVI/VGA Adapter

Terminal Terminal

Terminal

SERIAL PORT IN

SERIAL PORT OUT

R/C JACK

USB

AUDIO OUT

RESET

(MONO)

R/Pr G/Y B/Pb H/HV V

VIDEO/Y

ANALOG RGB

DVI

S-VIDEO

AUDIO

CONTROL PORT

(MONO)

AUDIO

CONTROL PORT

(MONO)

AUDIO

(MONO)

AUDIO

CONTROL PORT

(MONO)

INPUT 1

INPUT 2INPUT 3INPUT 4

OFF

DIP

2 3 4 5 6

CONNECTING PROJECTOR

CONNECTING TO VIDEO EQUIPMENT

Video Source (example)

Video Cassette Recorder

Video Disc Player

Video

Cable ✽

S-VIDEO

Cable ✽

Audio Amplifier

Audio Speaker (stereo)

Audio Cable

(Stereo) ✽

S-VIDEO Output

Audio Input

Cables used for connection

• Video Cable (BNC x 1, BNC x 2 or BNC x 3) ✽

• S-VIDEO Cable ✽

• Audio Cable (RCA x 2) ✽

(✽ = Cables are not supplied with this projector.)

NOTE :

When connecting cable, power cords of both a projector and external equipment should be disconnected from AC outlet. Turn a projector and peripheral equipment on before computer is switched on.

Audio Output

Pb/Cb

Pr/Cr

External Audio Equipment

AV AUDIO IN

S-VIDEO

Pr/Cr-Y-Pb/Cb

VIDEO

AUDIO OUT

Component video output equipment.

(such as DVD player or

high-definition TV source.)

Composite

Video Output

Component Video Output

Audio Cable

(Stereo) ✽

Video

Cable ✽

Video

Cable ✽

Separate Y/C

Video Output

Y-C

Terminals of

a Projector

SERIAL PORT IN

SERIAL PORT OUT

R/C JACK

USB

AUDIO OUT

(MONO)

RESET

R/Pr G/Y B/Pb H/HV V

VIDEO/Y

ANALOG RGB

DVI

S-VIDEO

AUDIO

CONTROL PORT

(MONO)

AUDIO

CONTROL PORT

(MONO)

AUDIO

(MONO)

AUDIO

CONTROL PORT

(MONO)

INPUT 1

INPUT 2INPUT 3INPUT 4

IMAGE BUTTON

Used to select image level. (P32, 37)

BEFORE OPERATION

AUTO PC ADJUST

IMAGE

SELECT

VOLUME

ZOOM FOCUS

LENS SHIFT

ON-OFF

INPUT 1/2

INPUT 3/4

SIDE CONTROLS AND INDICATORS

Used to adjust zoom. (P23)

INPUT 3/4 BUTTON

POWER ON–OFF BUTTON

FOCUS BUTTONS

VOLUME BUTTONS

Used to select input source either INPUT 3 or INPUT 4. (P26)

Used to adjust focus. (P23)

Used to adjust volume. (P25)

Used to select an item or adjust value in MENU. It is also used to pan image in DIGITAL ZOOM mode. (P34)

Used to execute item selected. It is also used to expand image in DIGITAL ZOOM mode. (P34)

Used to turn a projector on or off. (P22)

ZOOM BUTTONS

Used to select LENS SHIFT function. (P23)

SELECT BUTTON

POINT BUTTONS

LENS SHIFT BUTTONS

SIDE CONTROLS

MENU BUTTONS

Used to open or close MENU operation. (P20, 21)

INPUT 1/2 BUTTON

Used to select input source either INPUT 1 or INPUT 2. (P26)

SIDE CONTROLS

REAR INDICATORS

FRONT INDICATORS

AUTO PC ADJ. BUTTON

Use to operate AUTO PC Adjustment function. (P29)

BEFORE OPERATION

READY

LAMP

REPLACE

WARNING

TEMP.

READY INDICATOR

LAMP INDICATOR

LAMP REPLACE INDICATOR

This indicator lights green when a projector is ready to be turned on. And it flashes green in Power Management mode. (P41)

This indicator is dim when a projector is turned on. And bright when a projector is in stand-by mode.

INDICATORS

WARNING TEMP. INDICATOR

This indicator flashes red when internal projector temperature is too high. (P43)

WARNING

TEMP.

READY

LAMP

REPLACE

LAMP

FRONT INDICATORS

REAR INDICATORS

This LAMP REPLACE indicator lights yellow when any of Projection Lamps is nearing its end, and flashes when any of them becomes out. Check which lamp needs to be replaced on Lamp Status Display.

(P45-47)

+ 39 hidden pages