Christie Digital Systems 104-007101-XX, 38-DHD106-XX, 104-017101-XX, 38-DSP104-XX, 104-018101-XX User Manual

...
Stacking Frame Installation Instructions
Introduction
Use the following instructions when installing stacking frames onto the models listed in Table 1. Only use the stacking frame provided by Christie (104-117101-01) to hoist or stack a maximum of three projectors. The stacking frame can also be connected to the integral rigging points on any Roadster/Mirage S+ and Roadster HD12k projectors. For information on the rigging hardware of these models, refer to section 2.2 Installation Considerations in the Roadster S+/HD & Mirage S+ User’s Manual.
Table 1. Projector Models
Projector Model Model Number
Christie DS+4K 38-DSP104-xx
Christie DS+5K/Kc 38-DSP104-xx/38-DSP104-5x
Christie DS+8K 38-DSP106-xx/38-DSP106-5x
DLV1920-DX 104-017101-xx
DLV1400-DX 38-DSP102-xx Christie DW3K/Kc 38-DHD103-xx/38-DHD103-5x Christie DW6K/Kc 38-DHD106-xx/38-DHD106-5x
Christie HD5K 104-006101-xx
Christie HD5Kc 104-007101-xx
Christie HD8K 104-008101-xx
Christie HD8Kc 104-018101-xx
Mirage S+2K 38-DSP102-xx/38-DSP102-5x Mirage S+4K 38-DSP104-xx/38-DSP104-5x Mirage S+8K 38-DSP106-XX/38-DSP106-5X
Mirage W3 104-012101-xx
OFFICIALLY RELEASED
Document Control
September 8, 2006
Mirage W6 104-013101-xx Mirage W8 104-014101-xx
Matrix 4000 38-DSP104--xx
Matrix W4 104-016101-xx
013-100342-01 (Rev.1) (08/06) 1 of 12 pages
Stacking Frame Installation Instructions
Warnings
Christie stacking hardware is required to prevent the top projector from sliding
off the stack. Failure to incorporate this hardware may cause injury or death.
This procedure must only be performed by a qualified service technician.
The frame is designed to support a maximum stacking capacity of three
projectors. Always stack before hoisting.
Never attempt to physically carry a stack of projectors. Always follow the
Hoisting Procedure, outlined on page 6.
Use metric hardware only. Never force incompatible threads.
Always use all rigging points.
The stacking frame handles have a maximum load capacity of 360 lbs.
The projectors can be stacked and hoisted in either an upright or inverted
position. Do not mix orientations in a stack (i.e. inverted and upright).
All rigging must be in compliance with applicable local safety codes.
Only licensed riggers should perform the procedures outlined in this document.
OFFICIALLY RELEASED
Document Control
September 8, 2006
013-100342-01 (Rev.1) (08/06) 2 of 12 pages
Figure 1. Projector with Stacking Frame
Stacking Frame Installation Instructions
1. Stacking Frame Installation
ALWAYS power down and unplug the projector prior to servicing.
Wait for the internal cooling fans to stop before unplugging the unit.
WARNING
To avoid possible injury, a minimum of two
1. Turn the projector OFF and disconnect the AC power cord after the cooling fans have stopped. Allow the projector to cool for at least 45 minutes.
2. Place the projector into the stacking frame so the cut-outs in the bottom mounting plate of the frame align with the fold mirror and adjustable feet access points on the projector. Refer to Figure 2.
3. Use a 10mm socket wrench to tighten the six (6) M10 bolts securing the mounting plate to the bottom of the projector. Refer to Figure 2.
people are required to complete this procedure.
WARNING
Document Control
OFFICIALLY RELEASED
September 8, 2006
013-100342-01 (Rev.1) (08/06) 3 of 12 pages
Figure 2. Projector Orientation for Stacking Frame Assembly
Stacking Frame Installation Instructions
2. Stacking Multiple Projectors
Warnings
Christie stacking hardware is required to prevent the top projector from sliding
off the stack. Failure to incorporate this hardware may cause injury or death.
The frame is designed to support a maximum stacking capacity of three
projectors. Always stack before hoisting.
The projectors can be stacked and hoisted in either an upright or inverted
position. Do not mix orientations in a stack (i.e. inverted and upright).
Never attempt to physically carry a stack of projectors. Always follow the
Hoisting Procedure, outlined on page 6.
When hoisting a stack combining Roadster/Mirage S+ and Roadster HD12K
models with any of the models listed in Table 1, use the hardware provided with the Roadster/Mirage S+ and Roadster HD12K models to hoist the stack.
1. Place the first projector in the stack on a secure table or cart. For upright stack:
on the table or cart. Ensure the adjustable feet are NOT projector. When installing the second and third projector in the stack the feet must be retracted. All projectors must be stacked in the same orientation.
For inverted stack:
on the table or cart. Ensure the adjustable feet ARE installing a second and third projector. All projectors must be stacked in the same orientation.
OFFICIALLY RELEASED
2. Turn each stacking leg until at least 1” of thread is visible. For upright position: For inverted position:
This clearance accommodates the up-or-down movement for image alignment. Repeat Step 2 when installing a third projector.
IMPORTANT: Ensure all stacking legs are extended equally by at least 1”.
Place the projector to be positioned on the bottom of the stack
retracted on the bottom
Document Control
Place the projector to be positioned on the bottom of the stack
retracted. Repeat this step when
September 8, 2006
Extend the legs of the projector on the top of the stack.
Extend the legs of the projector on the bottom of the stack.
013-100342-01 (Rev.1) (08/06) 4 of 13 pages
Loading...
+ 8 hidden pages